REPAIR TO SANITARY FITTINGS PLUMBING FLOORING PLASTERING PLINTH PROTECTION SUNKEN FLOOR AND CONNECTED WORKS IN ZONE C AREA UNDER AGE BR N NO 1 OF GE N SECUNDERABAD

Amount

Dismantling floor, hearth or wall tiling including cement mortar bedding removing serviceable tiles and rubbish off the premises etc and removal of rubbish/ demolished materials out of MD land complete all as specified and as directed.

M&L for Screed bed or bedding layer of mortar 15 mm thick for laying floor finishes in CM 1:6 etc: complete all as specified and as directed.

M&L for Rendering 10 mm thk in CM (1:4) as in backing coat of cement plaster for laying of wall tiles etc: complete all as specified and as directed.

M&L for Non-skid ceramic tiles (Coloured) 7 to 8mm thick rectangular area of each tiles exc 0.18 sqm not exceeding 0.36 sqm in floors etc,.set and jointed in neat cement slurry and pointed in white or coloured cement to match, etc complete all as specified and as directed.

M&L for Non-skid ceramic tiles (Coloured) 7 to 8mm thick rectangular area of each tiles exceeding 0.18 sqm not exceeding 0.36 sqm in floors etc,.set and jointed in neat cement slurry and pointed in white or coloured cement to match etc.complete all as specified and as directed.

S&F Non Skid (coloured) ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match etc complete all as specifed and as directed.

M&L for Glazed (Coloured) ceramic tiles in vertical surfaces 300 x 450 x 8 to 9 mm/ 450 x 350 x 8 to 9 mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to matchet complete all as specified and as directed.

M&L reinforced cement concrete(nominal mix) type B1 1:2:4 (using 20 mm graded aggregate) as in slab supported on walls, beams and columns in floors,roof, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed.

M&L for formwork to sides and soffits o floor or roof beams, beam haunhings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs,etc. also splays between floors and beams etc as in rough finished flat surfaces of concrete complete all as directed.

S & F mild steel TMT bars 10 mm dia over, cut to length, bent to shape required including crancking bending spirally for hooping for col hooking ends and binding with and including mile steel wire non less than 0.9 mm dia securing with clips in quality complete all as specifed and directed.

All as per item No 10 here in before but 6mm to 8mm dia quality conforming complete all as specified and as directed.

M&L for 20 to 25mm thick machine cut and machine polished cudappa stone slab for kitchen plateform jointed and set in CM 1:3 and fixed including rounding to edge of stone slabs one side edge etc complete all as specified and as directed

M&L for machine cut granite 18 to 20 mm thick (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills,cooking platforms and like laid over & including 10mm thick bedding /backing coat in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of slab complete all as specified and as directed.

M&L for rounding and moulding to edges of stone slabs one edge, such as in steps, cooking platform and other similar situations complete all as specified and as directed.

Demolition of brickwork or stone/boulder masonry, built in cement mortar with all quoins, arches, pillars, etc but excluding ashlar facings, dressed stone work and precast concrete articles including disposal of the rubbish out off the premises complete all as specified and as directed.

M&L for brick work with fly ash bricks old size, straight or curved on plan exceeding 6.0 metre mean radius built in cement mortar 1:6 complete all as specified and as directed

M&L for brick work with flyash bricks, straight, or curved on plan to any radius as in half brick thick wall in CM 1:4 complete all as specified and directed.

Demolition of concrete in sunken floor incl removal of filling etc complete incl removal of demolished material to a distance complete all as specified and as directed.

Material and labour for rendering 15 mm thick on fair face of brickwork or concrete surfaces of sunken floors duly mixed with water proofing compound as per manufacturer's instructions in cement mortar 1:3 and finished even and smooth without using extra cement complete all as specified and as directed Note : Water proofing compound shall be measured and paid separately under relevant items in this schedule.

Material and labour for application of one coat of water based bitumen emulsion primer at the rate of 0.3 litre per SQM after cleaning of the surfaces thoroughly from dust, dirt and projections and applying water proofing treatment with APP polymeric membrane of weight 3 kilogram per SQM and minimum 3mm thick reinforced with polyster non oven fabric (weight not less than 150 gm/SQM) over that a coat of blown bitumen of 85 / 25 at the rate of 1.2 kilogram per SQM over that providing a sand layer of 25mm thick thick in sunken floors complete all as specified and as directed.

Supply only integral water proofing compound complete all as specified and as directed.

M&L for plain cement concrete, Type E2 (1:5:10) mix (Using 40 mm graded stone aggregates) for filling in sunken floor and mass concrete complete all as specified and as directed.

Taking down cement plaster of any description and thickness on brick walls including racking out joints, hacking for key, scrubbing down with water etc complete all as specified and as directed

Material and labour for rendering 10 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 without using extra cement complete all as specified and as directed

M & L for rendering 5 mm thick in cement plaster 1:3 on concrete surfaces of ceiling finished even and smooth without using extra cement in patchesnot exceeding 3 sqm each patch all as specified and as specified.

M&L for preparation of newly plastered surfaces of wall and applying three coats of white wash on wall surfaces complete all as specified and as directed.

M & L for preparing newly plastered ceiling surfaces and applying three coats of white wash complete all as specified and as directed.

Demolition of concrete in ground floors (un re-inforced) and pavingnot exceeding 15 cm thickness (below or above ground level) and including removal of rubbish/ demolished materials out of MD land complete all as specified and directed.

Material and labour for 40mm thick plain cement concrete 1:2:4 type B1 using 20mm graded stone aggregate as in floor finishes and finished even and smooth using extra cement complete all as specified and as directed.

Material and labour for 75 mm thick plain cement concrete 1:3:6, type C2 (using 40 mm graded stone aggregate) in plinth protection / paths laid in alternative bays finished even and smooth without using extra cement including making 10 mm wide grooves to full depth at the junction of wall and plinth protection , at 3 metre interval and every change of direction duly filling the grooves with mixture of bitumen and sand mixed in the ratio of 1:3 by weight and top 10 mm depth to be sealed with ceiling compound grade ‘A’ complete all as specified and as directed

Dismantling / taking down PVC/ Cast iron soil /waste pipes 100 mm / 75mm bore including all fitting like bends etc complete all as specified and as directed

S&F PVC (SWR) Nahani /Floor trap, 75 mm dia of out let, plain with grating including jointing to waste pipe with solvent and cement concrete type B1 (1:2:4) & including removing old trap and fixing of stainless steel grating in ground shape etc complete all as specified and as directed.

S&F 75mm bore PVC (SWR) pipe single socketed(ISI Marked) any length with rubber ring joints, complete fittings etc fixed to wall fixed with MS clamps 8mm dia with two nuts wall nails etc complete all as specifed and as directed.

S&F 110mm bore PVC (SWR) pipe single socketed(ISI Marked) any length with rubber ring joints, complete fittings etc fixed to wall fixed with MS clamps 8mm dia with two nuts wall nails etc complete all as specifed and as directed.

S&F 75mm bore PVC (SWR) bends any radius dimnishing pieces or tapers with access doors etc, complete all as specified and as directed.

S&F 110mm bore PVC (SWR) bends any radius dimnishing pieces or tapers with access doors etc, complete all as specified and as directed.

S&F 75mm bore PVC (SWR) branch piece, single (single Y ) equal or unequal with access doors etc, complete all as specified and as directed.

S&F 110 mm bore PVC (SWR) junction single (single T ) equal or unequal with access doors etc, complete all as specified and as directed.

S&F for 75mm bore PVC (SWR) vent cowl etc, complete all as specified and as directed.

S&F for 110 mm bore PVC (SWR) vent cowl etc, complete all as specified and as directed.

Taking down chowkats or frame with shutters ( without taking off shutters from the frame ) not exceeding 1.5 Sqm each complete all as specified and as directed.

S & F Solid PVC door framed of size 50mm x 95mm made out of 5mm prelam PVC sheet re-inforced with MS square tube, supplying & fixing in opening as per spcification & drawing etc, complete all as specified and as directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail ; Panelling of prelam PVC sheet on both sides to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawings given in Section 8 of MES Schedule Part-II 2020 as applicable complete all as specified and directed.

Supply and fix butt hinges of 100mm size extruded aluminium alloy with galvanised mild steel hinge pin, anodised, type C-21 complete all as specified and as directed

S/F 150mm length extruded aluminium alloy handles, fabricated type, anodised complete all as specified and as directed.

S&F 200mm length aluminium anodised barrel tower bolt of extruded section complete all as specified and as directed.

Taking up or down steel tubing and connection, removing clear off site after credit for the same is recovered by the dept., bore of pipe 15mm complete all as specified and as directed.

Taking up or down steel tubing and connection, removing clear off site after credit for the same is recovered by the dept., bore of pipe 20mm complete all as specified and as directed.

Taking up or down steel tubing and connection, removing clear off site after credit for the same is recovered by the dept., bore of pipe 25mm complete all as specified and as directed.

Taking up or down steel tubing and connection, removing clear off site after credit for the same is recovered by the dept., bore of pipe 40mm complete all as specified and as directed.

Cutting and grooving of wall for fixing of CPVC pipe lines and after fixing of CPVC pipe line and making good of all cutting surfaces etc complete all as specified and as directed.

S&F CPVC pipes, SDR 11, 20 mm outer dia of pressure rating 6kgf/sqcm conforming to IS-15778 with all CPVC fittings with such as brass elbow ,Tee, bends, unions, sockets ,Threaded Adoptor and end pieces etc to receive fittings and fixed with solvents fixed to walls / ceiling with all clamps in Shafts/ducts with all necessary scaffolding to fix the pipes and testing the joints under prescribed pressure etc complete all as specified and as directed.

S&F Tubes, ‘medium grade’ galvanised, 15 mm bore with all fitting and fixed complete to walls and ceilings or laid in floors etc complete all as specified and as directed.

S&F Tubes, ‘medium grade’ galvanised, 20 mm bore with all fitting and fixed complete to walls and ceilings or laid in floors etc complete all as specified and as directed.

S&F Tubes, ‘medium grade’ galvanised, 25 mm bore with all fitting and fixed complete to walls and ceilings or laid in floors etc complete all as specified and as directed.

S&F GI tube medium grade of 40 mm bore with all fittings and fixed complete to walls and ceilings or laid in floors etc complete all as specified and as directed.

S&F in repair for gun metal globe or gate valves with iron wheel head, screwed both ends for iron pipe & fixed of size 25 mm bore complete all as specified and as directed.

S&F in repairs for 20mm gun meteal, globe or gate valves, with iron wheel head screwed both ends for iron pipe and fixed omplete all as specified and as directed.

Cutting holes into or through brick/ stone walls built in cement mortar of superficial area not exceeding 150 Sq.cm and making good in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required complete all as specified and directed

S&F stainles steel sink with drainage board , 1 mm thick sheet of steel grade AISI 304 for kitchen or laboratory, with plug, waste pipe, washers and wastes including bedding in cement morter to dwarf wall or including fixing CI cantilever bracket, connecting union to pipe etc., overall size 915 x 460 mm with bowl size 410 mm x 330 mm x 160 mm etc complete all as specified and directed. Make : Nirali, Bule star (ISI marked).

S&F in repairs stainless steel kitchen plate rack of size 90cm x120cm x 1mm thick (18 gauge) conforming to the sample kept in the office of the AGE B/R I, complete all as specified and as directed.

S&F in repairs vitreous china water closet 'Orissa' pattern of size 580mm X 440mm, white with integral foot rest (excluding flushing cistern), but including PVC flush pipe and provision of lime concrete bedding complete all as specified and as directed.

S&Fin repair wash down water closet (pedestal pattern) white and including plastic water closet seat cover as per reqd colour with flat bottom and cover and mild steel chromium plated or aluminium hinging device (excluding flushing cistern) etc complete all as specified and directed.

S&F in repairs vitreous china wash basin, white, flat back, size 580mm X 450mm including CI brackets, 32mm dia brass chromium plated waste fittings with long screwed shanks and fly nuts flanged end bedded in red lead cement and other end fixed with & including cutting for & pinning in end of brackets and 15mm bore pillar tap, cast copper alloy fancy type chromium plated, screwed down high pressure complete all as specified and as directed.

S&F in Low level flushing cistern 10 ltr capacity, PVC incl waste pipe, down take pipe, pair of CI brackets and all accessories complete all as specified and as directed.

Supply and fix in repairs of stop valves cast copper alloy, fancy type chromium plated screwed down with long shank and cup (concealed) type, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe and fixed to 15 mm bore pipe complete all as specified and as directed

S&F in repairs CP angle cock 15mm bore fancy type chromium plated.with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

S&F in repairs CP bib tap 15mm bore fancy type with crutch or butterfly handle, screwed for iron pipe or for unions and fixed complete all as specified and directed.

Supply and fix in repairs of brass chromium plated, hand shower health faucet with health facet tube of 1.2 metre long and stand etc screwed for 15 mm bore iron pipe for two in one tap for WC complete all as specified and as directed. Make: CAT No F160038 of HINDWARE or equivalent in PARRY WARE/CERA as approved

Supply and fix in repairs brass chromium plated two way Bib tap screwed for 15mm dia bore iron pipe complete all as specified and as directed MAKE: CAT No F200004FT of HINDWARE or equivalent in PARRY WARE/CERA as approved

S&F in repairs Pillar taps, fancy type, chromium plated, screwed down, high pressure, with or without lettered ‘Hot' or ‘Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed 15 mm bore complete all as specified and as directed.

S&F in repairs chromium plated shower roses 125mm size with or without swivel joint including fixing to steel pipe or union etc.complete all as specified and as directed.

S&F in repairs 15mm size PVC connection with PTMT nuts 450mm length.complete all as specified and as directed.

S&F in repairs 15mm size PVC connection with PTMT nuts 600mm length.complete all as specified and directed.

S&F in repairs low density polyethene pipes (LDPE) 32mm of pressure rating 6 Kg/cm2 fixed to walls or laid in floors etc.complete all as specified and as directed.

Supply and fixed in repairs PTMT bath room mirror cabinet of size 330x430mm complete all as specified and as directed MAKE: CAT No 551 of PRAYAG or equivalent model in POLYTUF as approved by GE

S&F in repairs Towel Rail, 600mm long of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats. Minimum weight 190gms) complete all as specified and as directed.

Supply and fixed in repairs 15 mm dia bib tap of standard PTMT of any colour screwed for iron pipe minimum weight 90 grams complete all as specified and as directed.

Supply and fixed in repairs 15 mm dia Stop valve of standard PTMT of any colour screwed for iron pipe minimum weight 90 grams complete all as specified and as directed.

Supply and fixed in repairs 15 mm dia Angle Stop valve of standard PTMT of any colour screwed for iron pipe minimum weight 90 grams complete all as specified and as directed.

Supply and fixed in repairs 15 mm dia Pillar tap fancy type of standard PTMT of any colour screwed for iron pipe minimum weight 120 grams complete all as specified and as directed.

Supply and fixed in repairs PVC waste pipe 32/40 mm dia fixed to WHB/Kitchen Sink complete all as specified and as directed.

Supply and fixed in repairs PVC lid for 500/1000 litres capacity water tank complete all as specified and as directed.

Disconnecting existing tanks disconnecting existing tank, setting aside (or lowering if required) for repairs, cheaning, etc. and hoisting if required reconnecting and re-fixing in position. (Cleaning repainring, etc. measured separately), exceeding 250& not exceeding 500 litrs tanks complete all as specified and as directed.

Disconnecting existing tanks disconnecting existing tank, setting aside (or lowering if required) for repairs, cheaning, etc. and hoisting if required reconnecting and re-fixing in position. (Cleaning repainring, etc. measured separately), exceeding 500& not exceeding 1000 litrs tanks complete all as specified and as directed.

Cleaning of PVC water tank capacity not exceeding 500 litres at any height ( on accessible/inaccessible roofs) by removing all scale, dirt, mud ,any foreign material and removing accumulated silt, other dirty substance, algae, fungus and other bacterial material from sides/bottom of tank by draining / pumping out water/sludge from bottom and other growth from wall/ floor by high pressure cleaning method with jet set, vaccum machine and again cleaning the tank with fresh water and disinfecting the tank Disinfecting by using UV radiator and approved chemical (chloriten). for following capacities of tanks complete all as specified and as directed. Note:- (i) Unit rate quoted shall include for necessary ladder and machinery for pressure cleaning and safety apparatus required for execution of work. (ii) Unit rate quoted shall include for writing the date of actual cleaning with white paint on black background to match with the existing.

All as item No 87 above but of capacity exceeding 501 ltrs but not exceeding 1000 litres complete all as specified and as directed.

S & F in repair Ball valve of size 15mm dia high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball screwed for iron pipe and fixed complete all as specified and as directed. Make:- PRAYAG / SYMET.

All as item No 89 above but of size 20 mm dia complete all as specified and as directed.

All as item No 89 above but of size 25 mm dia complete all as specified and as directed.

Supply and fixed in repairs 1000 litres capacity rotational moulded polyethylene water storage tank of triple layer type(cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I complete all as specified and as directed

Supply and fixed in repairs 500 litres capacity rotational moulded polyethylene water storage tank of triple layer type(cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I complete all as specified and as directed.

Dismantling stone slabs and tiles of any description or thickness in floors aprons etc laid bedded and pointed in any mortar complete all as specified and as directed.

M&L for machine cut kota stone flooring 20-25mm thick over cement scredd base laid and jointed with gray cement slurry mixed with pigment to match the shade of the slab inclduing rubbing and polishing over screed bed of 15mm thick in cm 1:6 complete all as specified and as directed.

M&L for machine cut kota stone as in skirting / dado 20-25mm thick over cement plster of 10mm thick base laid and jointed with gray cement slurry mixed with pigment to match the shade of the slab inclduing rubbing and polishign complete all as specified and as directed.

SURA INFRASTRUCTURE

M/s GM Constructions

Pragathi Infrastructure Co.

K LAKSHMAN SINGH AND CO

MINOR INTERIORS

SKY CONSTRUCTIONS

R G NAIDU CIVIL CONTRACTOR AND BUILDERS