Construction of Permanent Campus for JNV, Shahdara, Delhi (U.T. of Delhi)

GRAND TOTAL OF DSR AND NDSR 69,68,83,000.06

Sl. No. Ref. (DSR-2 DESCRIPTION UNIT correction Total Qty DSR Amount NDSR Amount

SH-1 EARTH WORK

Earth work in Excavation by mechanical means (Hydraulic

excavator)/manualmeans over areas (exceeding 30 cm in

depth, 1.5 m in width as well as 10sqm on plan) including

getting out and disposal of excavated earth lead upto 50 m

1 2.6 and lift upto 1.5 m, as directed by Engineer-in-charge.

Filling available excavated earth (excluding rock) in trenches,

plinth, sides of foundations etc. in layers not exceeding 20cm

in depth, consolidating each deposited layer by ramming and

3 2.25 watering, lead up to 50 m and for all lift. Cum 196 190.708 8624.72 1644803.10

Excavating, supplying and filling of local earth (including

royalty) by mechanical transport upto a lead of 5km also

including ramming and watering of the earth in layers not

exceeding 20 cm in trenches, plinth, sides of foundation etc.

Extra for every additional lift of 1.5 m or part thereof in

5 2.26 excavation / banking excavated or stacked materials.

Clearing grass and removal of the rubbish up to a distance of

7 2.32 50 m outside the periphery of the area cleared. Sqm 8.95 8.70835 8788.19 76530.63

Supplying chemical emulsion in sealed containers including

8 2.34 delivery as specified.

9 2.34.1 Chlorpyriphos/ Lindane emulsifiable concentrate of 20% Litr 234.75 228.41175 3297.9 753279.11

Diluting and injecting chemical emulsion for POST-

CONSTRUCTIONAL anti-termite treatment (excluding the cost

10 2.35 of chemical emulsion) :

Treatment of soil under existing floors using chemical emulsion

@ one litre per hole, 300 mm apart including drilling 12 mm

diameter holes and plugging with cement mortar 1 :2

(1 cement : 2 Coarse sand) to match the existing floor:

Digitally signed by ANUJ

With Chlorpyriphos E.C. 20% with 1%

TOTAL EARTH WORK 11124476.34 0.00

B 4 CONCRETE WORKS

Providing and laying in position cement concrete of specified

grade excluding the cost of centering and shuttering - All work

13 4.1 up to plinth level :

1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural

sources : 8 graded stone aggregate 40 mm nominal size Cum 6812 6628.076 1496.59 9919512.26

14 4.1.8 derived from natural sources)

Providing and laying damp-proof course 40mm thick with

cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III)

derived from natural sources : 4 graded stone aggregate

15 4.1 12.5mm nominal size derived from natural sources)

Extra for providing and mixing water proofing material in

cement concrete work in doses by weight of cement as per Per 50 kg 18.15 17.65995

16 4.12 manufacturer's specification.

Making plinth protection 50mm thick of cement concrete 1:3:6

(1 cement : 3 coarse sand (zone-III) derived from natural

sources : 6 graded stone aggregate 20 mm nominal size

derived from natural sources) over 75mm thick bed of dry Sqm 749.3 729.0689 1798.7973 1311447.17

brick ballast 40 mm nominal size, well rammed and

consolidated and grouted with fine sand, including necessary

17 4.17 excavation, levelling & dressing & finishing the top smooth.

Providing & applying a coat of residual petroleum bitumen of

grade of VG-10 of approved quality using 1.7kg per square

metre on damp proof course after cleaning the surface with Sqm 146.15 142.20395 1503.2 213760.98

brushes and finally with apiece of cloth lightly soaked in

18 4.13 kerosene oil.

TOTAL (Carried Over to Summary of Civil Works) 12045635.20 0.00

C 5 REINFORCED CEMENT CONCRETE WORK

Centering and shuttering including strutting, propping etc. and

19 5.9 removal of form for :

Foundations, footings, bases of columns, etc. for mass

Digitally signed by ANUJ

Walls (any thickness) including attached pilasters,

21 5.9.2 butteresses,plinth and string courses etc. Sqm 842.5 819.7525 0.00

Suspended floors, roofs, landings, balconies and access

22 5.9.20 platform. with water proof ply 12 mm thick Sqm 1028.4 1000.6332 23843.094 23858191.45

23 5.9.4 Shelves (Cast in situ) Sqm 927.25 902.21425 0.00

Lintels, beams, plinth beams, girders, bressumers and

25 5.9.6 Columns, Pillars, Piers, Abutments, Posts and Struts. Sqm 961.3 935.3449 10503.42 9824320.33

26 5.9.7 Stairs, (excluding landings) except spiral-staircases. Sqm 764.95 744.29635 682 507610.11

27 5.9.16 Edges of slabs and breaks in floors and walls

Extra for additional height in centering, shuttering where ever

required with adequate bracing, propping etc., including cost

of de-shuttering and decentering at all levels, over a height of

3.5 m, for every additional height of 1 metre or part thereof

29 5.11 (Plan area to be measured).

Suspended floors, roofs, landing, beams and balconies (Plan

Steel reinforcement for R.C.C. work including straightening,

cutting, bending, placing in position and binding all complete

31 5.22 upto plinth level.

32 5.22.6 Thermo-Mechanically Treated bars. kg 107.85 104.93805 337894.42 35457981.54

Steel reinforcement for R.C.C. work including straightening,

cutting, bending, placing in position and binding all complete

33 5.22A Above plinth level.

34 5.22A-6 Thermo-Mechanically Treated bars. kg 107.85 104.93805 696833.15 73124311.94

Providing and Laying in position ready mixied or site batched

design mix cement concrete for reinforced cement concrete

work : using Coarse aggregate and fine aggreagate is derived

from natural sources, portland pozzolana /ordinary portland

/Portland salg cement, admixtures in recomended proportion

as per IS; 9103 to accelerate / retard setting of Concrete, to

improve durability and workabilty without impairing Strength :

Inculding pupming of concrete to site of laying, Curing carriage

of all lead but excluding the cost of centring and shuttring

finishing and reinforcment as per Direction of EIC for following

grade of Conctrete

Digitally signed by ANUJ

Note Extra Cement up to 10% of the minimun specified cement

content in design mix shall be Payable separetaly. in case the

cement content indesign mix is more than110% of the

specified minimum cement content, the contractor shall have

the discreation to either Re design the mix or bear the cost of

36 Extra cemnt

37 5.33.1 All works upto plinth level.

Concrete M-25 Grade with Minimum cement content

39 5.33.2 All works above plinth level upto floor V level.

Concrete M-25 Grade with Minimum cement content

Add for using extra cement in the items of design mix over and

41 5.35 above the specified cement content therein. Quintal 733.5 713.6955 2953.46 2107871.11

TOTAL (Carried Over to Summary of Civil Works) 241174495.09 0.00

D 6 BRICK WORK

Brick work with common burnt clay F.P.S. (non modular) bricks

42 6.1 of class designation 7.5 in foundation and plinth in:

43 6.1.2 Cement mortar 1:6 (1 cement : 6 coarse sand) Cum 7132.25 6939.67925 326.77 2267693.78

Providing and laying autoclaved aerated cement blocks

masonry with 100 mm thick AAC blocks in super structure

above plinth level up to floor V level in cement mortar 1:4 (1

cement : 4 coarse sand ). The rate includes providing and

placing in position 2 Nos 6 mm dia M.S. bars at every third

Providing and laying autoclaved aerated cement blocks

masonry with 150mm/230mm/300 mm thick AAC blocks in

super structure above plinth level up to floor V level with RCC

band at sill level and lintel level with approved block laying

polymer modified adhesive mortar all complete as per

direction of Engineer-in-Charge. (The payment of RCC band

45 6.47 and reinforcement shall be made for seperately). Cum 8333.65 8108.64145 3686.048 29888839.76

TOTAL (Carried Over to Summary of Civil Works) 39394908.32 0.00

SH-8 MARBLE & GRANITE WORK

Digitally signed by ANUJ

Providing and fixing 18 mm thick gang saw cut, mirror

polished,premoulded and prepolished, machine cut for kitchen

platforms, vanity counters, window sills, facias and similar

locations of required size,approved shade, colour and texture

laid over 20 mm thick base cement mortar 1:4 (1 cement : 4

coarse sand), joints treated with white cement,mixed with

matching pigment, epoxy touch ups, including rubbing,

curing,moulding and polishing to edges to give high gloss finish

etc. completeat all levels.

47 47 Granite stone slab colour black, Cherry/Ruby red

8.3 Providing edge moulding to 18 mm thick marble stone

counters, Vanities etc., including machine polishing to edge to

give high gloss finish etc.complete as per design approved by

49 Engineer-in-Charge.

Extra for fixing marble /granite stone, over and above

corresponding basic item, in facia and drops of width upto 150

mm with epoxy resin based adhesive, including cleaning etc.

8.5 Extra for providing opening of required size & shape for wash

basins / kitchens sink in kitchen platform, vanity counters and

similar location in marble / Granite /stone work including

necessary holes for pillar taps etc. including moulding, rubbing

52 and polishing of cut edges etc. complete. Nos 978.7 952.2751 245.000 233307.40

Stone tile (polished) work for wall lining over 12 mm thick bed

of cement mortar 1:3 (1 cement : 3 coarse sand) and cement

slurry @ 3.3 kg/sqm including pointing in white cement

54 8.9.1 8 mm thick

55 8.9.1.2 Granite of any colour and shade

TOTAL (Carried Over to Summary of Civil Works) 27221454.04 0.00

E 9 WOOD AND P.V.C. WORK

Digitally signed by ANUJ

Providing and fixing fire resistant door frame of section 50 x 60

mm on horizontal side & 35 x 60 mm on vertical sides having

built in rebate made out of 1.6 mm thick GI sheet ( Zinc coating

not less than 120gm/sqm) suitable for mounting 120 minutes

Fire Rated Glazed Door Shutters. The frame shall be filled with

mineral wool Insulation having density minimum 96Kg/sqm .

The frame will have a provision of G.I. anchor fastners 14 nos (

5 each on vertical style & 4 on horizontal style of size M10 x 80

) suitable for fixing in the opening along with factory made

template for SS ball bearing hinges of Size 100x89x3mm for

fixing of fire rated glazed shutter . The frame shall be finished

with a approved fire resistant primer or powder coating of not

less than 30 micron in desired shade as per the directions of

Engineer - in- Charge . (Cost of SS ball bearing hinges is

Providing and fixing 60 mm thick glazed fire resistant door

shutters of 120 minutes Fire rating conforming to IS:3614 (Part

II) or EN1634-1:1999, tested and certified as per laboratory

approved by Engineer-in-Charge, with suitable mounting on

door frame, consisting of vertical styles, top rail & side rail 60

mm x 60 mm wide and bottom rail of 110 mm x 60 mm made

out of 1.6mm thick G.I. sheet (zinc coating not less than

120gm/sqm) duly filled mineral wool insulation having density

minimum 96 kg/cum and fixing with necessary stainless steel

ball bearing hinges of size 100x89x3mm of approved make,

including applying a coat of approved fire resistant primer or

powder coating not less than 30 micron etc all complete as per

direction of Engineer-in-Charge (panelling to be paid for

Digitally signed by ANUJ

Providing and fixing glazing in fire resistant door shutters, fixed

panels & partitions etc., with G.I. beading made out of 1.6 mm

thick G.I. sheet (zinc coating not less than 120 gm/sqm) of size

20 x 33 mm screwed with M4 x 38 mm SS screws at distance 75

mm from the edges and 150 mm c/c , including applying a coat

of approved fire resistant primer/powder coating of not less

than 30 micron on G.I. beading, & special ceramic tape of 5 x

20 mm size etc complete in all respect as per NBC 2016, IS

16231 (Part 3):2016 and as per direction of Engineer-in-

Charge with glass of required thickness having 120 minutes of

fire resistance both integrity & radiation control (EW120) and

minimum 20 minutes of insulation (EI20). The manufacturer

have to give test report/certification of fire glass and the glass

should have the stamp showing the value of E, EW & EI. The

glass shall be tested in approved NABL accredited lab or by any

other accreditation body which operates in accordance with

ISO/IEC 17011 and accredited labs as per ISO/IEC 17025 for

testing and calibration scopes shall be eligible. The maximum

glazing size shall not be more than 1100x2200 mm (w x h) or

Providing and fixing panic bar / latch (Double point) fitted with

a single body, Trim Latch & Lock on back side of the Panic

Latch of reputed brand and manufacture to be approved by

9.139 the Engineer- in- charge, all complete Nos 8366.15 8140.26395 6 48841.58

Providing and fixing pressed steel door frames conforming to

IS: 4351, manufactured from commercial mild steel sheet of

1.60 mm thickness, including hinges, jamb, lock jamb, bead

and if required angle threshold of mild steel angle of section

50x25 mm, or base ties of 1.60 mm, pressed mild steel welded

or rigidly fixed together by mechanical means, including M.S.

pressed butt hinges 2.5 mm thick with mortar guards, lock

strike-plate and shock absorbers as specified and applying a

coat of approved steel primer after pre-treatment of the

56 10.14 surface as directed by Engineer-in-charge:

58 Fixing with adjustable lugs with split end tail to each jamb

Digitally signed by ANUJ

Providing and fixing ISI marked flush door shutters conforming

to IS : 2202 (Part I) non-decorative type, core of block board

construction with frame of 1st class hard wood and well

matched commercial 3 ply veneering with vertical grains or

59 9.21 cross bands and face veneers on both faces of shutters:

35 mm thick including ISI marked Stainless Steel butt hinges

61 9.122 Providing and fixing to existing door frames.

30 mm thick Fiberglass Reinforced Plastic (F.R.P.) flush door

shutter in different plain and wood finish made with fire

retardant grade unsaturated polyester resin, moulded to 3 mm

thick FRP laminate all around, with suitable wooden blocks

inside at required places for fixing of fittings and polyurethane

foam (PUF)/Polystyrene foam to be used as filler material

throughout the hollow panel, casted monolithically with

testing parameters of F.R.P. laminate conforming to table - 3 of

62 9.122.2 IS: 14856, complete as per direction of Engineer-in-charge. sqm 4489.95 4368.72135

9.23 Extra for providing lipping with 2nd class teak wood battens 25

mm minimum depth on all edges of flush door shutters (over

63 all area of door shutter to be measured). Sqm 462.35 449.86655 1013.336 455865.99

9.40.1 Providing and fixing wooden moulded beading to door and

window frames with iron screws, plugs and priming coat on

64 unexposed surface etc. complete.

Providing 40x5 mm flat iron hold fast 40 cm long including

fixing to frame with 10 mm diameter bolts, nuts and wooden

plugs and embedding in cement concrete block 30x10x15cm

1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate

Providing and fixing aluminium sliding door bolts, ISI marked

anodised (anodic coating not less than grade AC 10 as per IS :

1868), transparent or dyed to required colour or shade, with

67 9.96 nuts and screws etc. complete :

Digitally signed by ANUJ

Providing and fixing aluminium tower bolts, ISI marked,

anodised (anodic coating not less than grade AC 10 as per IS :

1868 ) transparent or dyed to required colour or shade, with

69 9.97 necessary screws etc. complete :

9.1 Providing and fixing aluminium handles, ISI marked, anodised

(anodic coating not less than grade AC 10 as per IS : 1868)

transparent or dyed to required colour or shade, with

71 necessary screws etc. complete :

9.101 Providing and fixing aluminium hanging floor door stopper, ISI

marked, anodised (anodic coating not less than grade AC 10 as

per IS : 1868) transparent or dyed to required colour and

73 shade, with necessary screws etc. complete.

74 9.101.1 Single rubber stopper Each 39.6 38.5308 627.000 24158.81

Providing and fixing casement handle made of zinc alloyed

(white powder coated) for uPVC casement window with

75 9.149 necessary screws etc. complete. Nos 231.05 224.81165 2296.000 516167.55

Providing and fixing zinc alloyed (white powder coated) touch

lock for uPVC sliding window with necessary screws etc.

TOTAL (Carried Over to Summary of Civil Works) 8309472.74 0.00

F 10 STEEL WORK

Structural steel work riveted, bolted or welded in built up

sections, trusses and framed work, including cutting, hoisting,

fixing in position and applying a priming coat of approved steel

77 10.2 primer all complete.

78 M.S work Taken as 14Kg per sqm Kg 133.7 130.0901 146160 19013969.02

Steel work welded in built up sections/ framed work, including

cutting, hoisting, fixing in position and applying a priming coat

79 10.25 of approved steel primer using structural steel etc. as required.

In gratings, frames, guard bar, ladder, railings, brackets, gates

Digitally signed by ANUJ

Steel work in built up tubular (round, square or rectangular

hollow tubes etc.) trusses etc., including cutting, hoisting,

fixing in position and applying a priming coat of approved steel

primer, including welding and bolted with special shaped

81 10.16 washers etc. complete.

82 10.16.1 Hot finished welded type tubes Kg 194.4 189.1512 0 0.00

Providing and fixing stainless steel ( Grade 304) railing made of

Hollow tubes, channels, plates etc., including welding,

grinding, buffing, polishing

and making curvature (wherever required) and fitting the

same with necessary stainless steel nuts and bolts complete,

i/c fixing the railing with necessary accessories & stainless steel

dash fasteners , stainless steel bolts etc., of required size, on

the top of the floor or the side of waist slab with suitable

arrangement as per approval of Engineer-incharge,

(for payment purpose only weight of stainless steel members

shall be considered excluding fixing accessories such as nuts,

Fencing with angle iron post placed at required distance

embedded in cement concrete blocks,

every 15th post, last but one end post and corner post shall be

strutted on both sides and

end post on one side only and provided with horizontal lines

and two diagonals interwoven

with horizontal wires, of barbed wire weighing 9.38 kg per 100

m (minimum), between the two

posts fitted and fixed with G.I. staples, turn buckles etc.

complete. (Cost of posts, struts, earth

work and concrete work to be paid for separately). Payment to

be made per metre cost of total

84 16.18 length of barbed wire used.

Supplying at site Angle iron post & strut of required size

including bottom to be split and bent

at right angle in opposite direction for 10 cm length and

drilling holes upto 10 mm dia. etc.

Digitally signed by ANUJ

Supplying and fixing rolling shutters of approved make, made

of required size M.S. laths, interlocked together through their

entire length and jointed together at the end by end locks,

mounted on specially designed pipe shaft with brackets, side

guides and arrangements for inside and outside locking with

push and pull operation complete, including the cost of

providing and fixing necessary 27.5 cm long wire springs

manufactured from high tensile steel wire of adequate

strength conforming to IS: 4454 - part 1 and M.S. top cover of

87 10.6 required thickness for rolling shutters.

88 10.6.2 80x1.20 mm M.S. laths with 1.20 mm thick top cover Sqm 3307.05 3217.75965 10.50 33786.48

89 10.7 Providing and fixing ball bearing for rolling shutters. Nos 492.35 479.05655 2.00 958.11

Providing & fixing fly proof wire gauze to windows, clerestory

windows & doors with M.S. Flat 15x3 mm and nuts & bolts

90 10.29 complete

Stainless steel (grade 304) wire gauze of 0.5 mm dia wire and

TOTAL (Carried Over to Summary of Civil Works) 48313464.69 0.00

G 11 FLOORING WORK

52 mm thick cement concrete flooring with concrete hardener

topping, under layer 40 mm thick cement concrete 1:2:4 (1

cement : 2 coarse sand : 4 graded stone aggregate 20 mm

nominal size) and top layer 12 mm thick cement hardener

consisting of mix 1:2 (1 cement hardener mix : 2 graded stone

aggregate 6 mm nominal size) by volume, hardening

compound mixed @ 2 litre per 50 kg of cement or as per

manufacturer's specifications. This includes cost of cement

92 11.4 slurry, but excluding the cost of nosing of steps etc. complete. Sqm 978.45 952.03185 2075.60 1976037.31

Chequered terrazo tiles 22 mm thick with graded marble chips

of size up to 6 mm in floors, jointed with neat cement slurry

mixed with pigment to match the shade of the tiles, including

rubbing and polishing complete, on 20 mm thick bed of

93 11.19 cement mortar 1:4 (1 cement :4 coarse sand) :

94 11.19.1 Light shade pigment using white cement Sqm 1533.8 1492.3874 140.87 210232.61

Digitally signed by ANUJ

Providing and laying flamed finish Granite stone flooring in

required design and patterns, in linear as well as curvilinear

portions of the building all complete as per the architectural

drawings with 18 mm thick stone slab over 20 mm (average)

thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid

and jointed with cement slurry and pointing with white cement

slurry admixed with pigment of matching shade including

rubbing, curing and polishing etc. all complete as specified and

95 11.55 as directed by the Engineer-in-Charge :

Flamed finish granite stone slab Jet Black, Cherry Red, Elite

96 11.55.1 Brown, Cat Eye or equivalent Sqm 3186.7 3100.6591 2752.29 8533905.28

Providing and laying Polished Granite stone flooring in

required design and patterns, in linear as well as curvilinear

portions of the building all complete as per the architectural

drawings with 18 mm thick stone slab over 20 mm (average)

thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid

and jointed with cement slurry and pointing with white

cement slurry admixed with pigment of matching shade

including rubbing , curing and polishing etc. all complete as

97 11.56 specified and as directed by the Engineer-in-Charge.

Polished Granite stone slab of all colour and texture except

Extra for pre finished nosing to treads of steps of marble /

99 11.24 granite stone. Rmt 719.19 699.77187

Extra for marble / granite stone flooring in treads of steps and

100 11.25 risers using single length up to 2.00 metre. Sqm 851.8 828.8014

Kota stone slab flooring over 20 mm (average) thick base laid

over and jointed with grey cement slurry mixed with pigment

to match the shade of the slab, including rubbing and polishing

complete with base of cement mortar 1 : 4 (1 cement : 4

101 11.26 coarse sand) :

Kota stone slabs 20 mm thick in risers of steps, skirting, dado

and pillars laid on 12 mm (average) thick cement mortar 1:3 (1

cement: 3 coarse sand) and jointed with grey cement slurry

mixed with pigment to match the shade of the slabs, including

103 11.27 rubbing and polishing complete. Sqm 2354.7 2291.1231 934.30 2140605.48

Digitally signed by ANUJ

Providing and laying rectified Glazed Ceramic floor tiles of size

300x300 mm or more (thickness to be specified by the

manufacturer), of 1st quality conforming to IS : 15622, of

approved make, in colours White, Ivory, Grey, Fume Red

Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement: 4

Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm

including grouting the joints with white cement and matching

Providing and fixing 10 mm thick acid and/or alkali resistant

tiles of approved make and colour using acid and/or alkali

resisting mortar bedding, and joints filled with acid and/or

alkali resisting cement as per IS : 4457, complete as per the

105 11.21 direction of Engineer-in- Charge. Sqm 1738.15 1691.21995 429.70 726710.45

In flooring on a bed of 10 mm thick mortar 1:4 (1 acid proof

106 11.21.1 cement : 4 coarse sand)

107 11.21.1.1 Acid and alkali resistant tile

In dado/skirting on 12 mm thick mortar 1:4 (1 acid proof

Providing and laying Vitrified tiles in floor in different sizes

(thickness to be specified by the manufacturer) with water

absorption less than 0.08% and conforming to IS:15622, of

approved brand & manufacturer, in all colours and shade, laid

on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand)

jointing with grey cement slurry @3.3 kg/sqm including

grouting the joints with white cement and matching pigments

etc. The tiles must be cut with the zero chipping diamond

cutter only . Laying of tiles will be done with the notch trowel,

plier, wedge, clips of required thickness, leveling system and

109 11.41A rubber mallet for placing the tiles gently and easily Sqm 1502.75 1462.17575 1616.92 2364226.55

110 11.41A.3 Glazed Vitrified tiles Matt/Antiskid finish of size

111 11.41A.1.1 Size of Tile 600x600mm

112 11.41A.1 Double charge vitrified tile polished finish of size Sqm 1453.65 1414.40145 796.65 1126784.97

113 11.41A.1.1 Size of Tile 600 x 600 mm

Digitally signed by ANUJ

Grouting the joints of flooring/wall tiles having joints of 3 mm

width, using epoxy grout mix of 0.70 kg of organic coated filler

of desired shade (0.10 kg of hardener and 0.20 kg of resin per

kg), including filling /grouting and finishing complete as per

114 11.48 direction of Engineer-in-charge.

Providing and laying Vitrified tiles in different sizes (thickness

to be specified by manufacturer), with water absorption less

than 0.08 % and conforming to I.S. 15622, of approved make,

in all colours & shade, in skirting, riser of steps, over 12 mm

thick bed of cement mortar 1:3 (1 cement: 3 coarse sand),

jointing with grey cement slurry @ 3.3 kg/ sqm including

grouting the joint with white cement & matching pigments etc.

117 11.46.2 Size of Tile 600x600 mm

TOTAL (Carried Over to Summary of Civil Works) 50313620.24 0.00

H 12 ROOFING WORK

Painting top of roofs with bitumen of approved quality @ 17kg

per 10 sqm impregnated with a coat of coarse sand at 60 cudm

per 10 sqm, including cleaning the slab surface with brushes

and finally with a piece of cloth lightly soaked in kerosene oil

118 12.15.1 complete :

119 12.15.1 With residual type petroleum bitumen of grade VG -10 Sqm 133.15 129.55495 4522.58 585922.03

12.21 Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement :

2 coarse sand : 4 stone aggregate 10 mm and down gauge),

including finishing with cement mortar 1:3 (1 cement : 3 fine

120 sand) as per standard design :

Making khurras 45x45 cm with average minimum thickness of

5cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4

graded stone aggregate of 20 mm nominal size) over P.V.C.

sheet 1 m x1 m x 400 micron, finished with 12 mm cement

plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat

cement, rounding the edges and making and finishing the

Digitally signed by ANUJ

Supply & fixing of Galvalume profile sheet of 1072

mm Supply width and nominal 28.5 mm deep ribs with subtle

square fluting in the five pans at nominal 203 mm centre-to-

centre. The end rib shall be designed for anti-capillary action,

to avoid any seepage of water through the lateral overlap. The

feed material is manufactured out of nominal 0.55 mm Base

Metal Thickness (BMT) with +/-0.05 mm Thickness tolerance,

Hi-Tensile steel with min. 550 MPa yield strength, metallic hot

dip coated with Aluminum-Zinc alloy (55% Aluminum, 45%

Zinc) as per AS 1397 - Zincalume AZ150 (Min. 150 gms/sq.mt

total on both sides) with Super durable Polyester Colorbond

XRW quality paint coat as per AS/NZS 2728 Class 3 of

BlueScope Steel make. The paint will have a total coating

thickness of nominal 35 μm, comprising of nominal 20 μm

exterior coat on top surface and nominal 5 μm reverse coat on

back surface over nominal 5 μm primer coat on both surfaces

of approved colour shade by concern authority. The exposed

paint system’s shall have higher SRI value (Thermatech

technology) and use inorganic (lead free) pigment in paint

system.The sheet shall have brand marking of the

manufacturer giving product details on the back of the sheet at

123 M.R every regular interval for confirming genuinity of the material. Sqm 972.42 8496.58 8262204.01

Providing and fixing Flashings/Trims/Gutter of same material

124 M.R as above Girth upto 610 mm RMTR 697.56 872.28 608466.2341

GI Metal Ceiling Lay in perforated Tegular edge global white

color tiles of size 595x595 mm and 0.5 mm thick with 8 mm

drop; made of GI sheet having galvanizing of 100 gms/sqm

(both sides inclusive) and 20% perforation area with 1.8 mm

dia holes and having NRC (Noise Reduction Coefficient) of 0.5,

electro statically polyester powder coated of thickness 60

microns (minimum), including factory painted after bending

and perforation, and backed with a black Glass fiber acoustical

TOTAL (Carried Over to Summary of Civil Works) 9942698.12 8870670.24

I 13 FINISHING WORK

126 13.4 12 mm cement plaster of mix :

Digitally signed by ANUJ

128 13.16.1 6mm cement Ceilling plaster of mix :-

18 mm cement plaster in two coats under layer 12 mm thick

cement plaster 1:5 (1 cement : 5 coarse sand) finished with a

top layer 6 mm thick cement plaster 1:6 (1 cement : 6 fine

Providing and applying plaster of paris putty of 2mm thickness

over plastered surface to prepare the surface even and

Finishing walls with Premium Acrylic Smooth waterproofing

exterior paint with Silicone additives of required shade having

antifungal properties on external walls two or more coats as

per manufacturer's specification. including priming coat of

132 M.R exterior primer applied @ 0.90 l/10 sqm) Sqm 237.96 9100.07 2165453.74

Providing and applying white cement based putty of average

thickness 1 mm, of approved brand and manufacturer, over

the plastered wall surface to prepare the surface even and

Wall painting with premium acrylic emulsion paint of interior

grade, having VOC (Volatile Organic Compound ) content less

than 50 grams/ litre of approved brand and manufacture,

including applying additional coats wherever required to

134 13.83 achieve even shade and colour.

Distempering with oil bound washable distemper of approved

136 13.41 brand and manufacture to give an even shade :

New work (two or more coats) over and including water

137 13.41.1 thinnable priming coat with cement primer Sqm 185.65 180.63745

Painting with synthetic enamel paint of approved brand and

138 13.62 manufacture of required colour to give an even shade :

Two or more coats on new work over an under coat of suitable

139 13.62.1 shade with ordinary paint of approved brand and manufacture Sqm 226.25 220.14125 4280.65 942348.52

Digitally signed by ANUJ

Providing & fixing Clay Exterior Wall Cladding Tiles of Length :-

230mm, width :- 75mm, 15 thick with back side groove of

1.75mm (Dimensional Tolerance ± 2mm) Made from unglazed

fired clay, fired at more than 1100 degree Celsius for minimal

porosity and high strength. in Smooth finish face with

completely natural and matt appearance. All natural shades

i.e. Terracotta, Brown, Chocolate and Beige. or as per

140 M.R approved fixed on 12mm cement mortar of 1:3 ratio Sqm 3013.00 2241.78 6754479.75

TOTAL (Carried Over to Summary of Civil Works) 31634740.12 8919933.49

ALUMINIUM WORKS

Providing and fixing aluminium work for doors, windows,

ventilators and partitions with extruded built up standard

tubular sections/ appropriate Z sections and other sections of

approved make conforming to IS: 733 and IS: 1285, fixing with

dash fasteners of required dia and size, including necessary

filling up the gaps at junctions, i.e. at top, bottom and sides

with required EPDM rubber/ neoprene gasket etc. Aluminium

sections shall be smooth, rust free, straight, mitred and jointed

mechanically wherever required including cleat angle,

Aluminium snap beading for glazing / paneling, C.P. brass /

stainless steel screws, all complete as per architectural

drawings and the directions of Engineer-in-charge. (Glazing,

141 21.1 paneling and dash fasteners to be paid for separately) :

142 For fixed portion

Anodised aluminium (anodised transparent or dyed to

required shade according to IS: 1868, Minimum anodic coating

For shutters of doors, windows & ventilators including

providing and fixing hinges/ pivots and making provision for

fixing of fittings wherever required including the cost of EPDM

rubber / neoprene gasket required (Fittings shall be paid for

144 21.1.2 separately)

Digitally signed by ANUJ

Anodised aluminium (anodised transparent or dyed to

required shade according to IS: 1868, Minimum anodic coating

Providing and fixing glazing in aluminium door, window,

ventilator shutters and partitions etc. with EPDM rubber /

neoprene gasket etc. complete as per the architectural

drawings and the directions of engineer-in-charge . (Cost of

146 21.3 aluminium snap beading shall be paid in basic item):

With float glass panes of 8 mm thickness (weight not less than

Filling the gap in between aluminium frame & adjacent RCC/

Brick/ Stone work by providing weather silicon sealant over

backer rod of approved quality as per architectural drawings

148 21.8 and direction of Engineer-in-charge complete. Rmtr 96.75 94.13775 6643.10 625366.49

149 21.8.1 Upto 5mm depth and 5 mm width

TOTAL (Carried Over to Summary of Civil Works) 12395466.29 0.00

M 22 WATER PROOFING

Providing and laying water proofing treatment in sunken

portion of WCs, bathroom etc., by applying cement slurry

mixed with water proofing cement compound consisting of

150 22.5 applying

First layer of slurry of cement @ 0.488 kg/sqm mixed with

water proofing cement compound @ 0.253 kg/ sqm. This layer

151 a) will be allowed to air cure for 4 hours

Second layer of slurry of cement @ 0.242 kg/sqm mixed with

water proofing cement compound @ 0.126 kg/sqm. This layer

will be allowed to air cure for 4 hours followed with water

TOTAL (Carried Over to Summary of Civil Works) 994015.01 0

26 New Technologies

Digitally signed by ANUJ

Providing and fixing factory made single extruded WPC solid

Decorative type Flushdoor shutter of Required size comprising

of virgin polymer of K value 58 -60 (suspension grade) ,

Calcium carbonate and natural fiberand Non Toxic

additiveshaving Minimum density of 65 kg/cum and screw

withdrawal strength of 1800N (Face) & 900N (Edge) , minimum

compresive strength 50 n/mm2 , modulusof elasticity 850

N/mm2 and Resistance to spread of Flame of Class A Category

with Propertyof being termite/borerproof , water/moisture

proof and fire Retardent . WPC to be Laminatewith PVC foil of

Minimum 14 micron thick of approved design pasted with hot

melt adesive on Both Face Shutter and fixing Stainless steel

153 26.88 Butt Hinges required Size

TOTAL (Carried Over to Summary of Civil Works) 3733253.561 0

Digitally signed by ANUJ

SUMMARY OF INTERNAL ELECTRICAL WORK

S. No. Description of item

Schedule Item DSR - 2022 Market Rate

A MAIN DISTRIBUTION BOARDS 2,253,601 409,764

C HOT DEEP GI CABLE TRAYS & GI RACEWAYS 1,141,973 0

D EARTHING 725,298 0

E. LIGHITNG ARRESTOR 1,521,389 0

F INTERNAL WIRING: 34,793,683 0

G LIGHTING FIXTURE AND FANS 0 11,507,823

TOTAL COST FOR DSR + MR 57050944

Digitally signed by ANUJ

BOQ INTERNAL ELECTRICAL

Sl. No. Description Unit TOTAL QTY. DSR Rate 2022 correction DSR Amount MR Rate MR Amount

1.0 DISTRIBUTION BOARDS

Supplying and fixing following way, single pole and

steel, MCB distribution board, 240 V, on surface/ recess,

with tinned copper bus bar. neutral bus bar, earth bar.

interconnections, powder painted including earthing

etc. as required.

(But without MCBIRCCB/lsolator)

Supplying and fixing of following ways surface/ recess

mounting, vertical type, 415 V, TPN MCB distribution

board of sheet steel, dust protected, duly powder

painted, inclusive Of 200 A tinned copper bus bar,

common neutral link. earth bar, din bar for mounting

MCBs (but without MCBs and incomer ) as required .

(Note : Vertical type MCB TPDB is normally used where 3

phase outlets are required.)

Supplying and fixing following way, horizontal type three

pole and neutral, sheet steel, MCB distribution board, 415

V, on surface/ recess, complete with tinned copper bus

bar, neutral bus bar, earth bar, din bar, interconnections,

powder painted including earthing etc. as required. (But

without MCB/RCCB/Isolator)

Digitally signed by ANUJ

BOQ INTERNAL ELECTRICAL

Sl. No. Description Unit TOTAL QTY. DSR Rate 2022 correction DSR Amount MR Rate MR Amount

Supplying and fixing 5 amps to 32 amps rating, 240 volts,

'C' series, miniature circuit breaker suitable for inductive

DSR-2.10 load of following poles in the existing MCB DB complete

with connections, testing and commissioning etc. as

DSR-2.10.3 Double pole Each 49 599 637 620 30,366

Supplying and fixing single pole blanking plate in the

existing MCB DB complete etc. as required.

Supplying and fixing following rating, double pole, (single

phase and neutral), 240 V, residual current circuit

DSR-2.14 breaker (RCCB), having a sensitivity current 30 mA in the

existing MCB DB complete with connections, testing and

commissioning etc. as required.

Supplying, fixing, connecting, testing and commissioning

of following rating, ISI marked (IS 8828) 240 / 415 volts, 10

KA, Miniature Circuit Breaker (MCB) of single / double /

three / four poles in the existing MCB DB or in existing MS

enclosure complete in all respects.

TOTAL CARRIED TO SUMMARY 2,253,601 409,764

Supply of XLPE insulated and PVC sheathed

Aluminium/Copper conductor arm oured cable of 1.1 KV grade

confirming to IS : 7098:1988 with upto date am endm ents of

following sizes:-

MR - 2 4 core, 16 Sq.mm. Copper cable Mtr 2675 0 1,530 4,091,746

MR - 3 3.5 core, 25 Sq.mm. Aluminium cable Mtr 535 0 644 344,373

Digitally signed by ANUJ

BOQ INTERNAL ELECTRICAL

Sl. No. Description Unit TOTAL QTY. DSR Rate 2022 correction DSR Amount MR Rate MR Amount

Laying and fixing of following sizes of one number PVC

DSR-7.8 insulated and PVC sheathed/XLPE Power cable of 1.1kv

grade on cable tray as required.

DSR-7.8.1 Upto 35 sq. mm (clamped with 1mm thick saddle) Mtr 3210 45 48 47 149,447 0

Supplying and making end termination with brass compression

gland and aluminium lugs for following size of PVC insulated

and PVC sheathed / XLPE aluminium conductor cable of 1.1

KV grade as required.

TOTAL CARRIED TO SUMMARY 261,294 4,436,119

HOT DEEP GI CABLE TRAYS & GI RACEWAYS

Supplying and installing following size of perforated Hot

Dipped Galvanised Iron cable tray (galvanisation

thickness not less than 50 microns) with perforation not

more than 17.5%, in convenient sections, joined with

connectors, suspended from the ceiling with G.I.

suspenders including G.I. bolts & nuts, etc. as required.

DSR-4.6.1 100 mm width X 50 mm depth X 1.6 mm thickness Metre 920 669 711 692 636,770 0

DSR-4.6.2 150 mm width X 50 mm depth X 1.6 mm thickness Metre 682 716 761 741 505,203 0

TOTAL CARRIED TO SUMMARY 1,141,973 0

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm

thick including accessories, and providing masonry

DSR-5.4 enclosure with cover plate having locking arrangement Each 34 7,472 7,945 7,730 262,836 0

and watering pipe of 2.7 metre long etc. with charcoal/

coke and salt as required.

Digitally signed by ANUJ

BOQ INTERNAL ELECTRICAL

Sl. No. Description Unit TOTAL QTY. DSR Rate 2022 correction DSR Amount MR Rate MR Amount

Providing & fixing of 25mm x 5mm GI strip on surface or

recess for earth connection as required.

Providing and fixing 6 SWG dia G.I. wire on surface or in

recess for loop earthing as required.

TOTAL CARRIED TO SUMMARY 725,298 0

LIGHTNING ARRESTOR

Providing and fixing of lightning conductor finial, made

of 25 mm dia 300 mm long, G.I. tube, having single prong

at top, with 85 mm dia 6 mm thick G.I. base plate

including holes etc. complete as required

Providing and fixing G.I. tape 20 mm X 3 mm thick on

DSR-6.7 parapet or on surface of wall for lightning conductor Meter 2200 126 134 130 286,789

complete as required.(For horizontal run)

Providing and fixing G.I. tape 20 mm X 3 mm thick on

DSR-6.8 parapet or on surface of wall for lightning conductor Meter 1450 197 209 204 295,531

complete as required. (For vertical run)

Providing and fixing testing joint, made of 20 mm X 3 mm

thick G.I. strip, 125 mm long, with 4 Nos. of G.I. bolts, nuts,

chuck nuts and spring washers etc. complete as

Providing and laying G.I. tape 32 mm X 6 mm from earth

electrode directly in ground as required.

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm

thick including accessories, and providing masonry

DSR-5.4 enclosure with cover plate having locking arrangement Nos 64 7472 7,945 7,730 494,750

and watering pipe of 2.7 metre long etc. with charcoal/

coke and salt as required.

Digitally signed by ANUJ

BOQ INTERNAL ELECTRICAL

Sl. No. Description Unit TOTAL QTY. DSR Rate 2022 correction DSR Amount MR Rate MR Amount

TOTAL CARRIED TO SUMMARY 1,521,389 0

INTERNAL WIRING:

Wiring for light point/ fan point/ exhaust fan point/ call

bell point with 1.5 sq.mm FRLS PVC insulated copper

conductor single core cable in surface / recessed steel

conduit, with modular switch, modular plate, suitable GI

box and earthing the point with 1.5 sq.mm FRLS PVC

insulated copper conductor single core cable etc. as

Wiring for group controlled (looped) light point/fan

point/exhaust fan point/ call bell point (without

independent switch etc.) with 1.5 sq. mm FRLS PVC

insulated copper conductor single core cable in surface/

recessed steel conduit, and earthing the point with 1.5

sq. mm FRLS PVC insulated copper conductor single core

cable etc. as required.

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC

insulated copper conductor single core cable in surface/

DSR-1.5 recessed steel conduit alongwith 1 No. 4 sq. mm FRLS meter 10690 433 460 448 4,788,883 0

PVC insulated copper conductor single core cable for

loop earthing as required.

Wiring for circuit/ submain wiring alongwith earth wire

with the following sizes of FRLS PVC insulated copper

conductor, single core cable in surface/ recessed steel

conduit as required.

DSR-1.7.3 2 X 4 sq. mm + 1 X 4 sq. mm earth wire meter 10690 428 455 443 4,733,584

Digitally signed by ANUJ

BOQ INTERNAL ELECTRICAL

Sl. No. Description Unit TOTAL QTY. DSR Rate 2022 correction DSR Amount MR Rate MR Amount

Supplying and fixing suitable size GI box with modular

plate and cover in front on surface or in recess, including

providng and fixing 2 Nos. 3 pin 5/6 A modular socket

outlet and 2 Nos. 5/ 6 A modular switch, connections etc.

as required. (For light plugs to be used in non residential

Supplying and fixing suitable size GI box with modular

plate and cover in front on surface or in recess, including

DSR-1.32 providing and fixing 6 pin 5/6 A & 15/16 A modular Each 957 586 623 606 580,201 0

socket outlet and 15/16 A modular switch, connections

etc. as required.

Supplying and fixing two module stepped type

electronic fan regulator on the existing modular plate

switch box including connections but excluding modular

plate etc. as required.

Supplying and fixing modular blanking plate on the

DSR-1.26 existing modular plate & switch box excluding modular Each 75 40 43 41 3,104 0

plate as required.

Providing and fixing circular/hexagonal Fan box cast iron

/metal sheet Box for ceiling fan clamp of internal dia

140mm , 73 mm height,Top id of 1.5mm thick MS sheet

with its Top surface hacked of proper bonding top lid

shall be screwed into cast iron /metal sheet Box by mean

of 3.3mm dia round headed screw one lock at the

corners.clamp shall be made of 12mm dia ms Bar band

toshape as per standrd drawing.

Supplying and fixing 20 A, 240 V, SPN Industrial type

socket outlet, with 2 pole and earth, metal enclosed plug

top alongwith 20 A "C" curve, SP, MCB, in sheet steel

enclosure, on surface or in recess, with chained metal

cover for the socket outlet and complete with

connections, testing and commissioning etc. as required.

Digitally signed by ANUJ

BOQ INTERNAL ELECTRICAL

Sl. No. Description Unit TOTAL QTY. DSR Rate 2022 correction DSR Amount MR Rate MR Amount

TOTAL CARRIED TO SUMMARY 34,793,683 0

LIGHTING FIXTURE AND FANS

Supply, Installation, testing and commissioning of

following type Fluorescent/ Compact fluorescent/LED

light fixtures on wall/ Ceiling including all fixing

accessories such as leads, etc complete as required. The

Fluorescent /CFL fixtures shall be complete with Low loss

copper ballast PF improvement capacitor, Bipin Rotor

type lamp holder, starter, starter base, all pre wired upto

the terminal block. All fixtures shall be supplied with

SITC of 18W LED light with die cast aluminium housing

MR - 4 with inbuilt controller and robust consction complete as Nos 852 0 2,660 2,266,347

SITC of Surface/Wall mounted 12W LED light with die cast

MR - 5 aluminium housing with inbuilt controller and robust Nos 441 0 1,637 721,882

consction complete as required.

SITC of 9w LED Bulkhead with a nominal system lumen

output of 600 lumens and a minimum system efficacy of

100 lm/W. The luminaire shall have a rated system lifetime

of 50,000 burning hours at L70. The luminaire should have

a color temperature of 6500K and CRI > 70. The luminaire

shall meet IP66 rating and IK 09 rating with THD < 20% and

PF > 0.9. The luminaire housing should made of High

pressure die cast Aluminium with polycarbonate front

diffuser. The total power consumption should not exceed

6W (including driver).

SITC of of 9W LED (mirror light) 2ft Batten with a nominal

system lumen output of 1150 lumens and a minimum

system efficacy of 115 lm/W. The luminaire shall have a

rated system lifetime of 25,000 burning hours at L70. The

MR - 7 luminaire should have a color temperature of 6500K and Nos 248 0 778 192,849

CRI>80. The luminaire shall meet IP20 rating with THD <

20% and PF > 0.9. The luminaire housing should made of

CRCA with a PC glossy diffuser. The total power

consumption should not exceed 10W (including driver).

Digitally signed by ANUJ

BOQ INTERNAL ELECTRICAL

Sl. No. Description Unit TOTAL QTY. DSR Rate 2022 correction DSR Amount MR Rate MR Amount

SITC of Surface or wall mounted 20W & 2000Lumens LED

MR - 8 Tube Rod with extruded aluminium housing with inbuilt Nos 801 0 1,160 928,835

controller and robust consction complete as required.

SITC of Surface or wall mounted 20W & 2000Lumens LED

MR - 9 Light with extruded aluminium housing with inbuilt Nos 1174 0 617 723,853

controller and robust consction complete as required.

SITC of ceiling fans complete with blades, down rods,

electronic regulator and accessories, 230 V, 1200mm

MR - 10 sweep. Min air delivery 210 CFM with service value 6.00 Nos 764 0 6,364 4,861,842

BEE. Five star rated with brushless direct current motor

SITC of exhaust fan, steel body AC single Phase. 230V of

size 300m sweep with, blades, and frame and louvers

SITC of Surface/Recessed type 36W LED light with die

MR - 12 cast aluminium housing with inbuilt controller and robust Nos 218 0 3,614 787,842

consction complete as required.

SITC of Surface/Wall Mounted Spot Focus light 36W LED

MR - 13 light with die cast aluminium housing with inbuilt Nos 17 0 2,101 35,712

controller and robust consction complete as required.

SITC of Wall fan 400 mm

TOTAL CARRIED TO SUMMARY 0 11,507,823

Digitally signed by ANUJ

Sub Head Description of item DSR 2022 Market Rate

A TELEPHONE SYSTEM 729797

B LAN NET-WORKING SYSTEM 567326

C CCTV (IP VIDEO SURVEILLANCE) SYSTEM 129893 482758

TOTAL COST FOR DSR + MR 1909774

Digitally signed by ANUJ

Description DSR rate with

Unit TOTAL QTY. DSR Rate 2022 correction DSR Amount MR Rate MR Amount

TELEPHONE SYSTEM

S.I.T.C. telephone point wiring with 2 pair

telephone wires of minimum 0.61mm.

diameter annealed copper wire, PVC

insulated, PVC sheathed in 25 mm

diameter concealed

PVC conduit system complete with all

sheet steel terminal box and socket to

1 accept RJ-11 plugs as follows

Telephone point wiring with 2 pair

telephone wires for 26

one no. telephone socket out let. Each

Telephone tag block as per ITI design for

termination of specified number of pairs

housed in suitable sized Sheetsteel Box

with hinged cover duly painted tag box

making the connections as follows

Telephone wires Mtr 495

Digital EPABX complete with : Each 1

one Operator Console with 24 Key DSS.

Built-in Charger & battery back-up

(at-least for 4 Hrs.),

facilities such as ISDN, DTMF/DISA,

Conference, MDF,COLA

for PIT protection,

TOTAL CARRIED TO SUMMERY Set 1 729797 729797

LAN NET-WORKING SYSTEM

Digitally signed by ANUJ

Description DSR rate with

Unit TOTAL QTY. DSR Rate 2022 correction DSR Amount MR Rate MR Amount

S.I.T.C. Network point wiring for computer

local area network (LAN) comprising of

RJ-45 socket connectors connected to a

10 base T network using UTP category 6

cable (CAT 6). The cable shall be laid in

25 mm. diameter concealed /exposed

metallic I PVC conduit system and shall

2 be complete with

Sheet metal switch box & RJ-45

connector-socket at one end and male 34

connector at the other end (Hub end) Each

24 Ports, 10/100Mbps, + 2 Port 1

OOOBase-T Unmanaged . 1

Stand-alone Switch. Each

19" 6U Rack with accessories Each 1

Patch panel Each 1

Cable Manager Each 1

Patch Cord Each 34

Information outlet ( 1/0) Each 34

Wi-Fi Router ( 50 mtr. Range ) Each 1

TOTAL CARRIED TO SUMMERY Set 1 567326 567326

CCTV (IP VIDEO SURVEILLANCE) SYSTEM

CCTV (IP VIDEO SURVEILLANCE) SYSTEM Complete set

and accessories as per required system & technical

Digitally signed by ANUJ

Description DSR rate with

Unit TOTAL QTY. DSR Rate 2022 correction DSR Amount MR Rate MR Amount

Supply, installation, testing and

commissioning of 3 MP Bullet camera ,

ONVIF profile S ,G & T . UL , CE , FCC

Certified ,1/2.8” Progressive Scan CMOS

,2.7 mm to 12 mm motorized varifocal lens

, Quad stream with each stream support

H.265+ compression simultaneously ,min

illumination : 0.01 Lux @ (F1.2,AGC ON), 0

Lux with IR , Shutter speed : 1 / 5s ~ 1 /

100,000 s ,120 dB WDR , Compression : 6 8702 52210

support , Alarm trigger - 1 input / 1 output

, frame rate : Main stream should support

25 fps@5MP , Edge analytics : line crossing

, perimeter intrusion ,Face detection

(deep learning) , pedestrian detection

,cross counting , stationary object , In built

IR LED , IR Distance upto 50 meters , IP 67 ,

3 IK 10 housing , POE. No.

Supply, installation, testing and

commissioning of 3 MP Dome camera ,

ONVIF profile S , G& T ,UL , CE , FCC

Certified ,1/2.8” Progressive Scan CMOS

,2.7 mm to 12 mm motorized varifocal lens

, Quad stream with each stream support

H.265+ compression simultaneously ,min

illumination : 0.01 Lux @ (F1.2,AGC ON), 0

Lux with IR , Shutter speed : 1 / 5s ~ 1 /

100,000 s ,120 dB WDR , Compression : 6 9013 54079

support upto 128GB , Alarm trigger - 1

input / 1 output , frame rate : Main

stream should support 25 fps@5MP ,Edge

analytics : line crossing , perimeter

intrusion ,Face detection(deep learning) ,

pedestrian detection ,cross counting ,

stationary object , In built IR LED , IR

4 Distance upto 40 meters , IP 67 , IK10 ,POE. Nos.

Digitally signed by ANUJ

Description DSR rate with

Unit TOTAL QTY. DSR Rate 2022 correction DSR Amount MR Rate MR Amount

Supply , installation , testing and

commissioning of PTZ Bullet camera in

metal body with continues 360° pan for

both indoor and outdoor with 30x

Minimum & 12x Digital Zoom or

better,Lens 4.3-129 mm or better, Image

Resolution 1920 x 1080 or better in H.264

and Motion JPEG, Day & Night, IP66 and

Edge Storage Built in SD card slot with

support upto 64 GB with Class 10 speed

Autotracking , Mounting brackets are

5 included. Nos.

Supply, installation, testing and

commissioning of 16 channel NVR ,

ONVIF compliant , recording bandwidth

640 Mbps , output interface 1 HDMI (up to

4K), 1 VGA , Alarm in/out :16ch in / 4ch

out , 1 X RJ45 ethernet , iOS smartphone

support , 8 HDD support , each HDD slot

support upto 8 TB HDD , RAID support ,

1x3.0 USB for backup /upgrade , 2x 2.0 1 107349 107349

USB for mouse .Edge analytics of poposed

cameras must be integrated with NVR .

Artificial Intelligence Support having face

recognition with compatible deep

learning supported cameras, AI-Face

registered quantity upto 10,000 ,A.I

maximum captured quantity 200,000. .

6 UL,CE,FCC certified. Nos.

Supply, installation, testing and

commissioning of user Client control

software (web based) with system

complete as per spec with valid licenses. 1 73128 73128

The software should enable the user to

view multiple cameras in any

7 combination available on the network . Set

Digitally signed by ANUJ

Description DSR rate with

Unit TOTAL QTY. DSR Rate 2022 correction DSR Amount MR Rate MR Amount

Supply, Installation, Testing and

Commissioning of Full HD 55" LED 1 42558 42558

8 Professional Display Panel. Nos.

Supply, Installation, Testing &

Commissioning of Surviellance Hard Disk. 1 15295 15295

9 (15 Days Storage) Nos.

10 Joystick controller Nos 1 61802 61802

Supplying and drawing of UTP 4 pair CAT 6

LAN Cable as per EIA in the existing

surface/ recessed Steel/PVC Conduit as

DSR-1.53 required.

Supplying and fixing of followmg smes ot

medium class PVC conduit

along With accessories in surface/recess

including cutting the wall

and making good the same in case of

DSR-1.21 recessed conduit as required.

TOTAL CARRIED TO SUMMERY 129893 482758

Digitally signed by ANUJ

SUMMARY - FIRE FIGHTING

FIRE FIGHTING WORKS

S. No. Description DSR Amount MR Amount

1 SUBHEAD-I: HYDRANT SYSTEM 576096.42 210068.00

2 SUBHEAD-II: PIPING VALVE & ACCESSORIES 2894971.56 52938.00

3 SUBHEAD- III : FIRE EXTINGUSHER 0.00 1038600.00

4 SUBHEAD-IV: FIRE PUMP 1121072.35 684978.00

5 SUBHEAD-V: FIRE ALARM SYSTEM 1339389.66 991338.00

GRAND TOTAL 8,909,452.00

GRAND TOTAL 8,909,452.00

Digitally signed by ANUJ

BOQ FIRE FIGHTING

DESCRIPTION UNIT RATE rate with DSR AMOUNT NDSR AMOUNT

No. Item correction

SUBHEAD-I: HYDRANT SYSTEM

Supplying, installation, testing and commissioning of weather

proof M.S cabinet size 900 mm wide x1000 mm height x 600mm

1 MR-1 deep fabricated from 1.6mm thick M.S. sheets and M.S angle

40mmx40mmx6mm complete with glass, locking arrangements

to accommodate the following.

First Aid hose Reel - 1 No.

Pressure Gauge - 1 No.

The cabinet shall be painted with one coat of primer and 2 coats

of synthetic enamel paint of approved shade.

Supplying and fixing single headed internal hydrant valve with

instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia

with cast iron wheel ISI marked conforming to IS 5290 (Type -A)

with blank Gunmetal/Stainless Steel cap and chain as required

DSR- 18.9.1 Single headed Gunmetal Each 7646 8130 7910 21 166120.12

Supplying and fixing first-aid Hose Reel with MS construction

spray painted in post office red, conforming to IS 884 complete

with the following as required. 20 mm nominal internal dia water

hose thermoplastic (Textile reinforced) type -2 as per IS: 12585.

20 mm nominal internal dia gun metal globe valve & nozzle.

Drum and brackets for fixing the equipmets on wall.

Connections from riser with 25 mm dia stop gun metal valve &

M.S. Pipe and socket.

Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63

4 DSR-18.16 mm dia male and female couplings duly bound with GI wire,

rivets etc. conforming to IS 636 (type-A) as required :

Supplying & fixing 63 mm dia gun metal short branch pipe with

20 mm nominal internal diameter size nozzle conforming to IS

903 suitable for instantaneous connection to interconnect hose

pipe coupling as required :

Digitally signed by ANUJ

BOQ FIRE FIGHTING

DESCRIPTION UNIT RATE rate with DSR AMOUNT NDSR AMOUNT

No. Item correction

SUBHEAD-I: HYDRANT SYSTEM

Supplying, installation, testing and commissioning of fire brigade

connection of cast iron body with gun metal male & female

6 DSR-18.19 instantaneous inlet couplings complete with cap and chain as Set 6742 7169 6975 5 34876.06

reqd. for suitable dia MS pipe connection conforming to IS 904 as

DSR-18.19.1 2 way - 100 mm dia M.S. Pipe

Supplying and fixing orifice plate made out of 6 mm thick

stainless steel (Grade 304) with orifice of required size to be

7 DSR-18.13 fitted between flange & landing valve of external and internal Each 1321 1405 1367 24 32800.67

hydrants to reduce pressure at the outlet to the level of 3.5

kg/cm2 complete as required.

Providing and fixing in position the industrial type pressure

gauges with gun metal / brass valves complete as required

Providing and fixing standard fire man's axe with heavily

insulated rubber handle complete as required.

4 buckets set with sand, self-supported M.S. stand i/c shed duly

painted with red colour as per IS.

Sub Total Amount Total 576096.4238 210,068.00

Sub Total Amount Total 576096.4238 210,068.00

SUBHEAD-II: PIPING VALVE & ACCESSORIES

Providing, laying, testing & commissioning of 'C' class heavy duty

MS pipe conforming to IS 3589/IS 1239

including Welding, fittings like elbows, tees, flanges, tapers, nuts

1 DSR-18.7 bolts, gaskets etc. and fixing the pipe on the wall/ceiling with

suitable clamp/support frame and painting with two or more

coats of synthetic enamel paint of required shade complete as

Digitally signed by ANUJ

BOQ FIRE FIGHTING

DESCRIPTION UNIT RATE rate with DSR AMOUNT NDSR AMOUNT

No. Item correction

SUBHEAD-I: HYDRANT SYSTEM

Supplying, fixing, testing and commissioning of butterfly valve PN

1.6, with Bronze/Gunmetal seat duly ISI marked complete with

7 DSR-18.11 Nuts, Bolts, washers, gaskets, confirming to IS 13095, of following

Providing, installation, testing and commissioning Stainless steel

6 DSR-18.15 strainer fabricated out of 1.6 mm thick stainless steel sheet with 3

mm dia holes with stainless steel flange

Providing, installation, testing and commissioning of dual plate

non- return valve of following sizes confirming to IS 5312

complete with rubber gasket, GI bolts, nuts, washers etc. as

Providing, Installation, Testing and Commissioning of 25mm dia

8 MR-4 Gun Metal / Bronze Ball Valves screwed ends of following sizes as Each 1,903 17 32,351.00

required. (PN-1.6)

Providing and fixing single acting air valve with screwed inlet 25

Sub Total amount 2894971.565 52938

Sub Total amount 2894971.565 52938

SUBHEAD- III : FIRE EXTINGUSHER

Supply, installation, testing and commissioning fire extinguisher

of carbon dioxide type consisting of brand new high pressure

steel cylinder bearing IS: 7285 mark and having the approval of

controller of explosives Nagpur, wheel type valve bearing IS:3224

mark internal discharge tube, 1 meter long high pressure

discharge hose, non conducting horn, suspension bracket, fully

charged bearing IS: making fixed to wall as directed conforming

Digitally signed by ANUJ

BOQ FIRE FIGHTING

DESCRIPTION UNIT RATE rate with DSR AMOUNT NDSR AMOUNT

No. Item correction

SUBHEAD-I: HYDRANT SYSTEM

Providing and fixing ABC Powder type fire extinguishers

consisting of welded M.S. cylinderical body, squeeze lever

discharge valve fitted with pressure indicating guase internal

2 discharge tube 30 cms long high pressure discharge hose,

discharge nozzle, suspension bracket conforming to IS:15683

finished externally with re enamel paint and fixed to wall with

brackets complete with inernal charge.

Supply, installation, testing and commissioning of ISI marked

(IS:15683:2006) portable chemical fire extinguisher, water (gas

3 pressure) type capacity 9 litres with gun metal cap and nozzle

and complete in all respects including initial fill and wall

suspension brackets as required as per specifications.

Sub Total amount 0 1038600

Sub Total amount 0 1038600

SUBHEAD-IV: FIRE PUMP

1 TERRACE LEVEL - FIRE PUMP

Supplying, storing, handling, shifting, installation, testing and

commissioning, supervision of testing of electric driven terrace

pump suitable for automatic operation & consisting of , complete

in all respects as required. (Terrace Pump)

B) horizontal type , multistage, centrifigual, split casing pump of

cast iron body & bronze impeller with stainless sheet shaft,

mechanical conforming to IS: 1520

C) Suitable HP Squirell cage induction motor TEFC suitable type

for operation on 415V, 3 phase 50HZ ac supply, with IP : 55 class

of protection of enclosure, horizontal foot mounted type with

class-F insulation , conforming to IS 325

D) MS fabricated common base plate , coupling, coupling guard,

foundation bolt etc. as required.

Digitally signed by ANUJ

BOQ FIRE FIGHTING

DESCRIPTION UNIT RATE rate with DSR AMOUNT NDSR AMOUNT

No. Item correction

SUBHEAD-I: HYDRANT SYSTEM

E) Suitable cement concrete foundation duly plastered and with

anti vibration pads.

Supply, installation, testing and commissioning of following cables:

4 Core 4Sqmm, unarmoured ATC copper conductor multistranded,

cable. Mtr 108.10

Laying of one number additional PVC insulated and PVC

sheathed / XLPE power cable of 11 KV grade of following size

direct in ground including excavation, sand cushioning,

protective covering and refilling the trench etc as required.

Fabrication, supply, Insallation testing & commissioning Of

Electrical control panel Of cubical construction, floor mounted

type, fabricated out Of 2mm thick CRCA sheet,

compartmentalised with hinged lockable doors, dust and vermin

proof, powder coated of approved shade after 7 tank treatment

process, cable alley, inter-connection with suitable size copper

conductor cable/solid copper strip, having switchgears and

accessories, mountings and internal wiring, earth terminals,

numbering etc. complete in all respect, suitable for main fire

pump, pressurisation pump & diesel pump set complete as per

CPWD specification with following in coming and Outgoings,

suitable for operation on 415V, 3 phase, 50HzAc Supply with

enclosure protection class IP 42 as required :

Digitally signed by ANUJ

BOQ FIRE FIGHTING

DESCRIPTION UNIT RATE rate with DSR AMOUNT NDSR AMOUNT

No. Item correction

SUBHEAD-I: HYDRANT SYSTEM

63A, 50kA 4 Pole MCCB, lcs=1000/0 lcu rating

Digital Voltmeter 0-500V with selector switch

Digital Ammeter (0-250 A) with selector swtich & CTs etc.

LED type RYB phase indicating lamps, ON, OFF, trip indicating

Set of Copper Bus Bar 300A

25 A, 50kA TPN MCCB, lcu, with fully automatic Star/Delta starter

suitable for 7 HP pump with overload protection, current sensing

type single phase preventor complete with all acceessories and

internal wiring required for automatic operation, selector switch

for local/remote, auto/manual/OFF operation.

MR-10 Total set Set 98864 5 494320

4 buckets set with sand, self-supported M.S. stand i/c shed duly

painted with red colour as per IS.

Providing and fixing resilient rubber neoprene lined single vibration

elimination connection with unit control suitable for raw water upto

45 deg.C. temperature working pressure 20 kg/Sq.Cm.

Sub Total amount 1121072.353 684978

Sub Total amount 1121072.353 684978

SUBHEAD-V: FIRE ALARM SYSTEM

Digitally signed by ANUJ

BOQ FIRE FIGHTING

DESCRIPTION UNIT RATE rate with DSR AMOUNT NDSR AMOUNT

No. Item correction

SUBHEAD-I: HYDRANT SYSTEM

Supplying, installation, testing and commissioning of micro processor

based intelligent addressable main fire alarm panel, central

processing unit with the following loop modules and capable Of

supporting not less than 240 devices (including detectors) and

minimum 120 detectors per loop and loop length up to 2 km,

network communication card, minimum 320 character graphics/ LCD

display with touch screen or other keypad and minimum 4000 events

history log in the non volatile memory (EPROM), power supply unit

(230 ± 5 % V, 50 hz), 48 hrs back-up with 24 volt sealed maintenance

free batteries with automatic charger. The panel shall have facility to

connect printer to printout log and facility to have seamless

integration with analog/digital voice evacuation system (which is

part of the schedule of work under SH: PA System) and shall be

complete with all accessories . The panel shall be compatible for

IBMS system with open protocol BACnet/ Modbus over IP complete

17.2.1 sgnifications, as

17.2.1.1 Two Loop Panel. Each 195,000 5 975000

Supplying, installation, testing & commissioning of intelligent analog

addressable photothermal detector complete with mounting base 2858 3039 2957 173 511536.92

17.2.4 complete as required. Each

Supplying, installation, testing & commissioning of fault isolator complete

with base as required.

Providing and fixing of self illuminated / auto glow

"EXIT" signs printed on photoluminescent sheet containing self

illuminated base chemical, of appropriate size not less than

400 x 150 mm, suspended from ceiling or fixed to the walls

with accessories as required and as directed at site etc. complete as

MR-13 required. Each

Supplying & laying of 2x1.5 sqmm fire alarm armoured cable,

600/1000V rated with annealed copper conductor having XLPE

insulation, steel wire armouring & FRLS outer sheath complete as

17.5.2 required. Each

Digitally signed by ANUJ

BOQ FIRE FIGHTING

DESCRIPTION UNIT RATE rate with DSR AMOUNT NDSR AMOUNT

No. Item correction

SUBHEAD-I: HYDRANT SYSTEM

Supplying and fixing of following sizes of steel along with accessories

in surface/recess including painting in case of surface conduit, or

DSR-EL-2022/1. cutting the wall and making good the same in case Of recessed

20 conduit as required.

Supplying, installation, testing & commissioning of addressable horn

17.2.15 cum strobe complete as required. Each

Sub Total amount 1339389.66 991338

Sub Total amount 1339389.66 991338

Digitally signed by ANUJ

SUMMARY - PLUMBING

INTERNAL PLUMBING WORKS

S. No. Description DSR Amount MR Amount

1 SANITARY FIXTURES & FITTINGS 7917606.91 8186912.80

2 WATER SUPPLY (INTERNAL) 6636950.54 573157.49

3 INTERNAL DRAINAGE (SOIL, WASTE, VENT, RAIN WATER

PIPES & FITTINGS) 1150976.2 4881563.1

GRAND TOTAL 29,347,166.98

GRAND TOTAL 29,347,166.98

Digitally signed by ANUJ

BOQ - INTERNAL PLUMBING

DSR / DSR Rate with QUANTI DSR NDSR

S.N NDSR ITEM UNIT DSR 2023 Rate

/ MR correction factor TY AMOUNT AMOUNT'

PART-B PLUMBING WORKS

A. SANITARY FIXTURES & FITTINGS

Providing and fixing white vitreous china extended wall

mounting water closet of size 780x370x690 mm of

approved shape including providing & fixing white vitreous

china cistern with dual flush fitting, of flushing capacity 3

litre/ 6 litre (adjustable to 4 litre/ 8 litres), including seat

cover, and cistern fittings, nuts, bolts and gasket etc

Providing and fixing water closet squatting pan (Indian

type W.C. pan ) with 100 mm sand cast Iron P or S trap, IO

litre low level white P.V.C. flushing cistem, including flush

pipe, with manually controlled device (handle lever)

forming to IS : 7231, with all fittings and fixtures complete,

including tting and making good the walls and floors

2 17.10 wherever required:

White Vitreous china Orissa pattem W.C. pan of size

3 17.1.1 580x440 mm with integral type foot rests Each 6767.40 6584.68 116 763822.90

Providing and fixing white vitreous china wash basin

including making all connections but excluding the cost of

4 17.25 fittings :

5 17.25.1 Flat back wash basin of size 630x450 mm Each 1339.70 1303.53 264 344131.42

Providing and fixing white vitreous china laboratory sink

with C.I. brackets, C.P. brass chain with rubber plug, 40 mm

C.P brass waste and 40mm C.P. brass trap with necessary

C.P. brass unions complete, including painting of fittings and

brackets, cutting and making good the wall wherever

6 17.11 required :

Digitally signed by ANUJ

BOQ - INTERNAL PLUMBING

DSR / DSR Rate with QUANTI DSR NDSR

S.N NDSR ITEM UNIT DSR 2023 Rate

/ MR correction factor TY AMOUNT AMOUNT'

PART-B PLUMBING WORKS

Providing and fixing of 15 mm dia C.P. brass Pillar cock

with CP wall flange of approved quality with flow rate of 5

9 MR-01 LPM complying to Green Building requirements. Each 1677.83 270 453012.81

Providing and fixing first quality C.P. brass Long Body Bib

cock of 15 mm nominal bore, with CP wall flange of

approved quality with flow rate of 5 LPM complying to

10 MR-02 Green Building requirements. Each 1901.52 285 541934.39

Providing and fixing white vitreous china flat back half stall

Providing and fixing first quality C.P. brass Pressmatic

Urinal flush Valve of approved quality with flow rate of 1

12 MR-03 LPM complying to Green Building requirements. Each 3169.62 53 167989.73

Providing and fixing Urinal Division Plate with table

rubbed, edges rounded and polished, of size 900 x 450 mm,

fixed in urinal partitions by cutting a chase of appropriate

width with chase cutter and embedding the stone in the

chase with epoxy grout or with cement concrete 1:2:4 (1

cement : 2 coarse sand : 4 graded stone aggregate 6 mm

nominal size) as per direction of Engineer-in-charge and

13 MR-04 finished smooth. Each 5315.81 47 249843.19

Digitally signed by ANUJ

BOQ - INTERNAL PLUMBING

DSR / DSR Rate with QUANTI DSR NDSR

S.N NDSR ITEM UNIT DSR 2023 Rate

/ MR correction factor TY AMOUNT AMOUNT'

PART-B PLUMBING WORKS

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen

sink as per IS:13983 with C.I. brackets and stainless steel

plug 40 mm, including painting of fittings and brackets,

14 17.1 cutting and making good the walls wherever required :

17.10.1 Kitchen sink with drain board

Providing and fixing C.P brass Sink mixer swivel spout (Wall

mounted) of approved make complete as required with

flow rate of 5 LPM complying to Green Building

15 MR-05 requirements. Each 5215.06 59 307688.83

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible

tube upto 1 metre long with S.S. triangular plate to

Eureopean type W.C. of quality and make as approved by

Providing and fixing of vitreous China Sanitary fixtures and

CP fitting and other accessories for Handicapped toilet .

Each Matrix Set shall comprised (Wash Basin 650 x 350

with one pair mounting brackets, EWC & Cistern complete

with fittings & seat cover, one no hinged rail 76 cm and five

MR-06 no's of grab rails 60 cm). complete all respect. Each 16388.83 6 98332.97

Digitally signed by ANUJ

BOQ - INTERNAL PLUMBING

DSR / DSR Rate with QUANTI DSR NDSR

S.N NDSR ITEM UNIT DSR 2023 Rate

/ MR correction factor TY AMOUNT AMOUNT'

PART-B PLUMBING WORKS

Providing and fixing of 1 No. Swing Handicap Grab Bar -

Stainless Steel at fixed height for handicap toilet complete

18 MR-07 as required. Each 12127.36 6 72764.18

Providing and fixing of 1 No. Stainless Steel Grab Barl (600

Mm),32mm Dia. at fixed height for handicap toilet complete

19 MR-08 as required. Each 5107.41 6 30644.46

Providing and fixing of 1 No. Stainless Steel Grab Bar (350

Mm),32mm Dia. at fixed height for handicap toilet complete

20 MR-09 as required. Each 3159.83 6 18958.98

Providing and fixing of 15 mm dia CP brass bib cock with

CP wall flange of approved quality with flow rate of 5 LPM

21 MR-10 complying to Green Building requirements. Each 1497.47 322 482184.67

22 17.34 Providing and fixing toilet paper holder.

Providing and fixing of C.P. brass twin coat hook with PVC

23 MR-11 rawl plug & C.P. brass screw complete as required. Each 1037.49 172 178447.76

Providing and fixing C.P. brass angle valve for basin mixer

and geyser points of approved quality conforming to

Digitally signed by ANUJ

BOQ - INTERNAL PLUMBING

DSR / DSR Rate with QUANTI DSR NDSR

S.N NDSR ITEM UNIT DSR 2023 Rate

/ MR correction factor TY AMOUNT AMOUNT'

PART-B PLUMBING WORKS

Providing and fixing uplasticised PVC connection pipe with

25 18.21 brass unions.

18.21.2 15 mm nominal bore

Providing & fixing chrome plated brass battery based

18.84 infrared operated pillar cock, having foam flow technology.

Providing and fixing C.P. brass shower rose with 15 or 20 mm

26 18.22 inlet

Providing and fixing of CP Brass Bath and Shower Mixer with

provision of overhead shower with 115mm long bend pipe, in

built spout, spout / shower selector with wall flange complete

with all accessories as required and making good the walls

wherever required. with flow rate of 5.0 LPM complying to

27 MR-12 Green Building requirements. Each 5847.01 208 1216179.00

Providing and fixing PTMT liquid soap container 109 mm

wide, 125 mm high and 112 mm distance from wall of

standard shape with bracket of the same materials with

snap fittings of approved quality and colour, weighing not

Digitally signed by ANUJ

BOQ - INTERNAL PLUMBING

DSR / DSR Rate with QUANTI DSR NDSR

S.N NDSR ITEM UNIT DSR 2023 Rate

/ MR correction factor TY AMOUNT AMOUNT'

PART-B PLUMBING WORKS

Providing and fixing PTMT soap Dish Holder having length

of 138mm, breadth 102mm, height of 75mm with

concealed fitting arrangements, weighing not less than 106

Providing and fixing PTMT towel ring trapezoidal shape

215 mm long, 200 mm wide with minimum distances of 37

mm from wall face with concealed fittings arrangement of

30 17.72 approved quality and colour, weighing not less than 88 gms. Each 231.95 225.69 264 59581.46

Providing and fixing 600x450 mm beveled edge mirror of

superior glass (of approved quality) complete with 6 mm

thick hard board ground fixed to wooden cleats with C.P.

31 17.31 brass screws and washers complete Each 1607.95 1564.54 265 414601.87

Providing and fixing PTMT towel rail complete with

brackets fixed to wooden cleats with CP brass screws with

concealed fittings arrangement of approved quality and

32 17.73 colour.

450 mm long towel rail with total length of 495 mm, 78 mm

wide and effective height of 88 mm, weighing not less than

Providing and fixing CP Brass 32mm size Bottle Trap of

approved quality & make and as per the direction of

33 17.22A Engineer-in-charge. Each 1034.80 1006.86 338 340318.82

Digitally signed by ANUJ

BOQ - INTERNAL PLUMBING

DSR / DSR Rate with QUANTI DSR NDSR

S.N NDSR ITEM UNIT DSR 2023 Rate

/ MR correction factor TY AMOUNT AMOUNT'

PART-B PLUMBING WORKS

Supply of solid state, no touch operating, fully hygienic hand

drier of approved shade with single blower, with time delay,

summer & winter control, music while drying, volume ON/OFF

MR-13 controls complete as required. Each 10209.14 33 336901.75

Providing, Fixing,testing and commissioning drinking

water water coolar with in built RO facility including angle

valve and flexible connection piping of the following

capacity. It shall have C.P brass push cock complete with

inlet float valve (with angle valve) with all plumbing and

electrical accessories, inlet, outlet, overflow and PVC drain

out connection to F.D complete as required. (Storage

Providing and fixing of Storage type water heater/ Geyser

with required accessories like 15 mm CP angle valve on

inlet & outlet line, heavy duty reinforced flexible PVC

connector for cold water line and flexible CP brass

connector with CP checkout for hot water line, CPVC line

connection, MS bracket with two coats of enamel paint,

anchor fastners etc. to hang the units, providing and fixing

of 16 A 3 Pin plug of Anchor make, etc. complete as

a MR-15 Capacity 15 Liters Each 12846.00 86 1104755.61

MR-16 Capacity 25 Liters Each 16597.15 44 730274.48

B. WATER SUPPLY (INTERNAL)

Digitally signed by ANUJ

BOQ - INTERNAL PLUMBING

DSR / DSR Rate with QUANTI DSR NDSR

S.N NDSR ITEM UNIT DSR 2023 Rate

/ MR correction factor TY AMOUNT AMOUNT'

PART-B PLUMBING WORKS

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC)

pipes, having thermal stability for hot & cold water supply,

including all CPVC plain & brass threaded fittings, i/c fixing

the pipe with clamps at 1.00 m spacing. This includes

jointing of pipes & fittings with one step CPVC solvent

cement and the cost of cutting chases and making good the

same including testing of joints complete as per direction of

1 18.8 Engineer in Charge.

Concealed work, including cutting chases and making

good the walls etc.

1.2 18.8.2 20 mm nominal outer dia Pipes Metre 537.60 523.08 2221 1161771.34

1.3 18.8.3 25 mm nominal outer dia Pipes Metre 627.25 610.31 924 563930.37

1.4 18.8.4 32 mm nominal outer dia Pipes Metre 739.30 719.34 959 689846.01

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC)

pipes, having thermal stability for hot & cold water supply,

including all CPVC plain & brass threaded fittings, including

fixing the pipe with clamps at 1.00 m spacing. This includes

jointing of pipes & fittings with one step CPVC solvent

cement and testing of joints complete as per direction of

2 18.7 Engineer in Charge.

Internal work - Exposed on wall

Digitally signed by ANUJ

BOQ - INTERNAL PLUMBING

DSR / DSR Rate with QUANTI DSR NDSR

S.N NDSR ITEM UNIT DSR 2023 Rate

/ MR correction factor TY AMOUNT AMOUNT'

PART-B PLUMBING WORKS

2.6 DSR _RA 65 mm dia nominal bore Metre 1165.00 1133.55 220 249379.90

Providing and fixing ball valve (brass) of approved quality,

4 18.18 High or low pressure, with plastic floats complete :

4.4 MR-17 32mm nominal bore Each 1006.73 96 96645.92

MR-18 40mm nominal bore Each 1112.99 66 73457.03

Providing and fixing gun metal gate valve with C.I. wheel of

5 18.17 approved quality (screwed end) :

Providing and fixing in position of approved quality high

pressure rated Gun Metal Float Valve with copper ball float

and brass rods of required length suitable for test pressure

7 of not less than 15 Kg/sqcm of the following sizes:

7.1 MR-19 20 mm dia nominal bore Each 1243.48 3 3730.4

7.2 MR-20 25mm nominal bore Each 3025.61 12 36307.3

7.3 MR-21 32mm nominal bore Each 3431.07 25 85776.6

Digitally signed by ANUJ

BOQ - INTERNAL PLUMBING

DSR / DSR Rate with QUANTI DSR NDSR

S.N NDSR ITEM UNIT DSR 2023 Rate

/ MR correction factor TY AMOUNT AMOUNT'

PART-B PLUMBING WORKS

7.4 MR-22 40mm nominal bore Each 4123.13 24 98955.2

DSR-2022 Providing and fixing in position the industrial type pressure

/16.8 gauges with gun metal/ brass valves complete as required Each 1196.00 1163.71

Water Level Indicator with Musical Alarm on Tank Full and Buzz

MR-23 Empty with 20 metres of Sensor Wire Each 1423.37 61 86825.4

Providing & fixing Auto Air vent for cold water supply

8 risers, suitable for pressure not less than 15 Kg/Sq.cm.

Supplying, fixing, testing and commissioning of butterfly valve

of PN 1.6 rating with bronze/gunmetal seat duly ISI marked

complete with nuts, bolts, washers, gaskets conforming to IS

18.11 13095 of following sizes as required :

Providing and fixing C.I. dirt box strainer for bulk type water

meter with nutsi bolts, rubber insertions etc. complete

18.61 conforming to IS : 2373 :

Providing and placing on terrace (at all floor levels)

polyethylene water storage tank, IS : 12701 marked, with

cover and suitable locking arrangement and making

necessary holes for inlet, outlet and overflow pipes but

9 18.48 without fittings and the base support for tank. per liter 11.00 10.70 107820 1153997.46

C. INTERNAL DRAINAGE (SOIL, WASTE, VENT, RAIN WATER PIPES & FITTINGS)

Digitally signed by ANUJ

BOQ - INTERNAL PLUMBING

DSR / DSR Rate with QUANTI DSR NDSR

S.N NDSR ITEM UNIT DSR 2023 Rate

/ MR correction factor TY AMOUNT AMOUNT'

PART-B PLUMBING WORKS

Providing, jointing, testing and fixing UPVC Soil, Waste &

Vent system conforming to IS : 13592 (Type-B) and UPVC

fittings (moulded as well as fabricated) like bends, tees,

Y-tees, crosses, boss connections, access pieces, saddle

pieces, cleanouts, adaptors for connections to other

materials, plugs, reducers, cowls, offset and other specials.

Jointing shall be done with push fit EPDM ring jointing

technique in general. Solvent cement joints may be

provided for fittings and specials which are not

manufactured with push fit rubber joints. Fixing at

wall/ceiling level supported by galvanized steel clamps &

hangers etc. Making proper connection and also pipes may

be laid / fixed in sunken floors, under slung from ceiling.

The pipes laid in sunken floor shall be encased with not less

than 75 mm thick cement concrete (1:2:4) all around. The

installation shall be complete in all respects including

cutting chases / holes in walls, slabs and making good the

same as per specifications. (All major MS structure to hold

1 the stack is included in this item).

Digitally signed by ANUJ

BOQ - INTERNAL PLUMBING

DSR / DSR Rate with QUANTI DSR NDSR

S.N NDSR ITEM UNIT DSR 2023 Rate

/ MR correction factor TY AMOUNT AMOUNT'

PART-B PLUMBING WORKS

Providing, jointing, testing and fixing UPVC Rain water

system conforming to IS : 13592 (Type -A) and UPVC

fittings (moulded as well as fabricated) like bends, tees,

Y-tees, crosses, boss connections, access pieces, saddle

pieces, cleanouts, adaptors for connections to other

materials, plugs, reducers, cowls, offset and other specials.

Jointing shall be done with push fit EPDM ring jointing

technique in general. Solvent cement joints may be

provided for fittings and specials which are not

manufactured with push fit rubber joints. Fixing at

wall/ceiling level supported by galvanized steel clamps &

hangers etc. Making proper connection and also pipes may

be laid / fixed in sunken floors, under slung from ceiling.

The pipes laid in sunken floor shall be encased with not less

than 75 mm thick cement concrete (1:2:4) all around. The

installation shall be complete in all respects including

cutting chases / holes in walls, slabs and making good the

same as per specifications. (All major MS structure to hold

2 the stack is included in this item).

2.1 MR-27 110 mm dia Type A Metre 691.00

Digitally signed by ANUJ

BOQ - INTERNAL PLUMBING

DSR / DSR Rate with QUANTI DSR NDSR

S.N NDSR ITEM UNIT DSR 2023 Rate

/ MR correction factor TY AMOUNT AMOUNT'

PART-B PLUMBING WORKS

Providing, fixing, jointing and testing UPVC soil, waste, vent

pipework comprising UPVC pipe conforming to IS

:4985-1983 of class 3 (6kg/cm2) as specified below and

fittings (moulded as well as fabricated) like elbows, bends,

reducers, threaded tail pieces, caps, suitable elbow with

suitable extension piece for drain point and other specials

jointing with cement solvent, chasing, cutting and making

good the walls & floors pipes laid in floors shall be encased

with 40 mm thick concrete all around, complete in all

respects including testing of complete installation.(All

major MS structure to hold the stack with fixing including

3 anchor fasteners, sand, cement etc is included in this item)

3.1 MR-29 40 mm od 6 kg/cm2 (Class III ) Metre 387.02 826.5 319868.6

Providing and fixing UPVC/SWR trap (P trap) of self

cleaning design as per IS:13592 : 1992 complete including

cost of cutting and making good the cutouts in walls and

floors etc.including cutting and making good the walls and

4 floors wherever required complete.

4.1 MR-30 110 mm inlet and 110 mm outlet Nos. 858.53 325 279021.5

Providing and fixing floor drain made out of 110x63 mm

OD uPVC elbow connected to uPVC pipe complete as per

5 MR-31 direction of Project Manager. Nos. 810.99 362 293579.0

Digitally signed by ANUJ

BOQ - INTERNAL PLUMBING

DSR / DSR Rate with QUANTI DSR NDSR

S.N NDSR ITEM UNIT DSR 2023 Rate

/ MR correction factor TY AMOUNT AMOUNT'

PART-B PLUMBING WORKS

Providing and fixing Inlet Fitting for Urinal trap, formed out

of 110 mm PVC pipe with multiple side inlets formed with

saddle pieces, suitable for 40, 50 and 63 mm dia side

connections as per standard detail and support through

galvanized steel support from slab or set in cement

concrete mix 1:2:4 including cutting and making good the

6 MR-32 walls and floors wherever required. Nos. 910.26 52 47333.4

Providing and fixing Heavy Class SS grating of approved

design including setting in floor with cement motor to

match with floor finish as per architect requirement

7 suitable for waster and FT, UT & FD.

Providing and fixing P.V.C. WC connector (straight or bend

type) with rubber lip ring. Including 110 mm dia PVC pipe /

bend of required length and proper connection with M seal

8 MR-34 to C.I. pipe complete as required. Nos. 896.28 192 172085.2

Providing and fixing M.S. holder bat clamps of approved

design to C.I. or S.C.I. rain water pipes embedded in and

including cement concrete blocks 10x10x10 cm of 1:2:4 mix

(1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm

nominal size) and cost of cutting holes and making good the

10 12.38 walls etc. :

Digitally signed by ANUJ

BOQ - INTERNAL PLUMBING

DSR / DSR Rate with QUANTI DSR NDSR

S.N NDSR ITEM UNIT DSR 2023 Rate

/ MR correction factor TY AMOUNT AMOUNT'

PART-B PLUMBING WORKS

Making khurras 45x45 cm with average minimum thickness

of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4

graded stone aggregate of 20 mm nominal size) over P.V .C.

sheet 1 m x1 m x 400 micron, finished with 12 mm cement

12.22 plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat

cement, rounding the edges and making and finishing the

outlet complete.

Constructing brick masonry catch basin

chamber30x30x77.5 cm with bricks in cement mortar 1:4

(1 cement : 4 coarse sand) including 500x450 mm pre-cast

R.C.C. horizontal grating with frame complete as per

standard design :

With common burnt clay F.P.S. (non modular) bricks of class

MR-35 designation 7.5 each 6262.34 38.00 237968.87

Providing and fixing 15 Cm wide, 45 cm overall

semi-circular plain G.S. sheet with iron

brackets 40x3mm size, bolts, nuts and washers etc.,

including making necessary connections

12.7 With rain water pipes complete.

12.7.1 0.80 mm thick with zinc coatin not less than 275 m/m2 Metre 1029.65 1001.85 1086.00 1088008.50

Digitally signed by ANUJ

BOQ BOUNDARY WALL

Sl. DSR- Description of Item Qty. Unit DSR 2023 Rate Rate with Amount Amount NDSR

No. 2023 (In Rs.) correction (In Rs.)

1 Earth work in Excavation by mechanical means (Hydraulic excavator)/manualmeans

over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10sqm on plan)

including getting out and disposal of excavated earth lead upto 50 m and lift upto

2.6 1.5 m, as directed by Engineer-in-charge.

3 2.25 Filling available excavated earth (excluding rock) in trenches, plinth, sides of

oundations etc. in layers not exceeding 20cm in depth, consolidating each

deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. 723.88 Cum 196 190.708 138049.707

5 4.1 Providing and laying in position cement concrete of specified grade excluding the

cost of centering and shuttering - All work up to plinth level :

6 4.1.10 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded

stone aggregate 40 mm nominal size derived from natural sources) 24.05 Cum 6518.6 6342.5978 152539.4771

7 5.1 Providing and laying in position specified grade of reinforced cement concrete,

excluding the cost of centering, shuttering, finishing and reinforcement - All work

up to plinth level :

8 5.1.2 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm

9 5.2 Reinforced cement concrete work in walls (any thickness), including attached

pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers,

abutments, posts and struts etc. above plinth level up tofloor five level, excluding

cost of centering, shuttering, finishing and reinforcement :

10 5.2.2 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm

11 5.22 Steel reinforcement for R.C.C. work including straightening, cutting, bending,

placing in position and binding all complete upto plinth level.

12 5.22.6 Thermo-Mechanically Treated bars of grade Fe-500D or more. 21634.7 Kg 107.85 104.93805 2270303.23

13 5.9 Centering and shuttering including strutting, propping etc. and removal of form for

14 5.9.1 Foundations, footings, bases of columns, etc. for mass concrete 345.8 Sqm 392.15 381.56195 131944.1223

15 5.9.6 Columns, Pillars, Piers, Abutments, Posts and Struts 593.19 Sqm 961.3 935.3449 554837.2412

16 5.9.5 Lintels, beams, plinth beams, girders, bressumers and cantilevers. 319.41 Sqm 736.4 716.5172 228862.7589

Digitally signed by ANUJ

17 5.9.15 Small lintels not exceeding 1.5 m clear span, moulding as in cornices, window sills,

string courses, bands, copings, bed plates, anchor blocks and the like 202.99 Sqm 392.15 381.56195 77453.26

18 6.4 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation

7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :

19 6.4.2 Cement mortar 1:6 (1 cement : 6 coarse sand) 178.41 Cum 9105.95 8860.08935 1580728.541

20 18 mm cement plaster in two coats under layer 12 mm thick cement plaster 1:5 (1

cement : 5 coarse sand) finished with a top layer 6 mm thick cement plaster 1:6 (1

13.11 cement : 6 fine sand).

22 13.46 Finishing walls with Acrylic Smooth exterior paint of required shade :

23 13.46.1 New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming

coat of exterior primer applied @ 2.20 kg/10 sqm) 2007.72 Sqm 160.6 156.2638 313733.9565

24 Providing and fixing concertina coil fencing with punched tape concertina coil 600

mm dia 10 metre openable length ( total length 90 m), having 50 nos rounds per 6

metre length, upto 3 m height of wall with existing angle iron 'Y' shaped placed

2.4m or 3.00 m apart and with 9 horizontal R.B.T. reinforced barbed wire, stud tied

with G.I. staples and G.I. clips to retain horizontal, including necessary bolts or G.I.

barbed wire tied to angle iron, all complete as per direction of Engineer-in-charge,

with reinforced barbed tape(R.B.T.) / Spring core (2.5mm thick) wire of high tensile

strength of 165 kg/ sq.mm with tape (0.52 mm thick) and weight 43.478 gm/ metre

16.53 (cost of M.S. angle, C.C. blocks shall be paid separately) 507.49 Sqm 375.8 365.6534 185565.444

26 10.1 Structural steel work in single section, fixed with or without connecting plate,

including cutting, hoisting, fixing in position and applying a priming coat of

approved steel primer all complete. 881.06 Kg 117.35 114.18155 100600.80

Digitally signed by ANUJ

BILL OF QUANTITY FOR ENTRY GATE

DSR- DSR 2023 DSR-23

S.No. Description Quantity Unit Correction MR-Amount

2023 Rate Amount

Earth work in excavation by mechanical means (Hydraulic

excavator)/ manual means over areas (exceeding 30 cm in

depth, 1.5 m in width as well as 10 sqm on plan) including

getting out and disposal of excavated earth lead upto 50 m

2.6 and lift upto 1.5 m, as directed by Engineer-incharge.

Providing and laying in position cement concrete of

specified grade excluding the cost of centering and

4.1 shuttering - All work up to plinth level :

1:5:10 (1 cement : 5 coarse sand (zone-III) derived from

natural sources : 10 graded stone aggregate 40 mm

4.1.10 nominal size derived from natural sources) 3.14 Cum 6,518.60 6,342.60 19,915.76

Providing and laying damp-proof course 40mm thick with

cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III)

derived from natural sources : 4 graded stone aggregate

4.1 12.5mm nominal size derived from natural sources) 3.12 Sqm 410.85 399.76 1,247.24

Providing & applying a coat of residual petroleum bitumen

of grade of VG-10 of approved quality using 1.7kg per

square metre on damp proof course after cleaning the

surface with brushes and finally with apiece of cloth lightly

4.13 soaked in kerosene oil. 3.12 Sqm 146.15 142.20 443.68

Centering and shuttering including strutting, propping etc.

5.9 and removal of form for

Foundations, footings, bases of columns, etc. for mass

Digitally signed by ANUJ

Suspended floors, roofs, landings, balconies and access

Lintels, beams, plinth beams, girders, bressumers and

5.9.6 Columns, Pillars, Piers, Abutments, Posts and Struts 78.24 Sqm 961.3 935.34 73,181.38

Providing and laying in position ready mixed or site batched

design mix cement concrete for reinforced cement concrete

work; using coarse aggregate and fine aggregate derived

from natural sources, Portland Pozzolana / Ordinary

Portland /Portland Slag cement, admixtures in

recommended proportions as per IS: 9103 to accelerate /

retard setting of concrete, to improve durability and

workability without impairing strength; including pumping of

concrete to site of laying, curing, carriage for all leads; but

excluding the cost of centering, shuttering, finishing and

reinforcement as per direction of the engineer-in-charge; for

5.33 the following grades of concrete.

5.33.1 All works upto plinth level

Concrete of M25 grade with minimum cement

5.33.2 All works above plinth level upto floor V level

Concrete of M25 grade with minimum cement content of

Steel reinforcement for R.C.C. work including straightening,

bending, placing in position and binding all complete upto

5.22 plinth level.

Thermo-Mechanically Treated bars of grade Fe-500D or

Digitally signed by ANUJ

Steel reinforcement for R.C.C. work including straightening,

cutting, bending, placing in position and binding all

5.22A complete above plinth level.

Thermo-Mechanically Treated bars of grade Fe-500D or

Brick work with common burnt clay F.P.S. (non modular)

bricks of class designation 7.5 in superstructure above

6.4 plinth level up to floor V level in all shapes and sizes in :

6.4.2 Cement mortar 1:6 (1 cement : 6 coarse sand) 19.61 Cum 9,105.95 8,860.09 173,746.35

Providing and fixing ISI marked flush door shutters

conforming to IS : 2202 (Part I) non-decorative type, core of

block board construction with frame of 1st class hard wood

and well matched commercial 3 ply veneering with vertical

grains or cross bands and face veneers on both faces of

35 mm thick including ISI marked Stainless Steel butt

9.21.1 with necessary screws 1.58 Sqm 2,392.65 2,328.05 3,678.32

Providing and fixing M.S. grills of required pattern in frames

of windows etc. with M.S. flats, square or round bars etc.

including priming coat with approved steel primer all

9.48.1 Fixed to steel windows by welding 1,359.18 Kg 219.1 213.18 289,755.84

Providing and fixing aluminium hanging floor door stopper,

anodised (anodic coating not less than grade AC 10 as per

transparent or dyed to required colour and shade, with

necessary screws

9.101 etc. complete. 0.00

9.101.2 Twin rubber stopper 1 Nos 72.35 70.40 70.40

Digitally signed by ANUJ

Providing & fixing Stainless steel Sliding door bolt ISI

Marked Anodised( anodic coating not less than grade AC

10 as per IS: 1868) transparent or dyed to required coloure

or shade with nuts and screws etc complete. A

M.R 250mmx16mm 1 Nos 750 750

Providing and fixing Stainless steel towerbolts (barrelType)

M.R with necessary screws etc . Complete

M.R providing and fixing SS Handles with screws etc Complete 2 Nos 500 1,000.00

Providing and fixing factory made ISI marked steel glazed

doors, windows and ventilators, side /top /centre hung, with

beading and all members such as F7D,F4B, K11 B and K12

B etc. complete of standard rolled steel sections, joints

mitred and flash butt welded and sash bars tenoned and

riveted, including providing and fixing of hinges, pivots,

including priming coat of approved steel primer, but

excluding the cost of other fittings, complete all as per

approved design, (sectional weight of only steel members

10.11 shall be measured for payment).

Fixing with 15x3 mm lugs 10 cm long embedded in cement

concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3

coarse sand : 6 graded stone aggregate 20 mm nominal

Providing and fixing T-iron frames for doors, windows and

ventilators of mild steel Tee-sections, joints mitred and

welded, including fixing of necessary butt hinges and

screws and applying a priming coat of approved steel

Fixing with 15x3 mm lugs 10 cm long embedded in cement

concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3

coarse sand : 6 graded stone aggregate 20 mm nominal

Digitally signed by ANUJ

Providing & fixing glass panes with putty and glazing clips in

10.3 windows, clerestory windows, all complete with : 0.54 Sqm 1,064.65 1,035.90 559.39

11.3 Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand :

4 graded stone aggregate) finished with a floating coat of

neat cement, including cement slurry, but excluding the cost

of nosing of steps etc. complete.

11.3.1 40 mm thick with 20 mm nominal size stone aggregate 4.13 Sqm 614.2 597.62 2,468.16

Providing and fixing glass strips in joints of terrazo/ cement

11.13 concrete floors.

15 mm cement plaster on the rough side of single or half

13.2 brick wall of mix :

13.1 12 mm cement plaster of mix :

13.16 6 mm cement plaster of mix :

15 mm cement plaster on rough side of single or half brick

13.5 wall of mix:

13.15 20 mm cement plaster 1:2 (1 cement : 2 stone dust). 1.62 Sqm 520.55 506.50 820.52

Digitally signed by ANUJ

13.5 Applying priming coat:

With ready mixed red oxide zinc chromate primer of

approved brand and manufacture on steel galvanised iron/

Painting with synthetic enamel paint of approved brand and

13.61 manufacture to give an even shade :

13.61.1 Two or more coats on new work 48.28 Sqm 155.9 151.69 7,323.63

13.61.1 Same as above but wooden painting 3.78 Sqm 155.9 151.69 573.39

Distempering with oil bound washable distemper of

13.41 approved brand and manufacture to give an even shade :

New work (two or more coats) over and including water

13.41.1 thinnable priming coat with cement primer 75.94 Sqm 185.65 180.64 13,717.61

Finishing walls with water proofing cement paint of required

13.44.1 New work (Two or more coats applied @ 3.84 kg/10 sqm) 198.13 Sqm 116.9 113.74 22,536.04

13.8 Providing and applying white cement based putty of

average thickness 1 mm, of approved brand and

manufacturer, over the plastered wall surface to prepare the

surface even and smooth complete. 274.07 Sqm 156.05 151.84 41,613.87

Providing and laying water proofing treatment on roofs of

slabs by applying cement slurry mixed with water proofing

22.6 cement compound consisting of applying:

after surface preparation, first layer of slurry of cement @

0.488 kg/sqm mixed with water proofing cement compound

(a) @ 0.253 kg/sqm.

Digitally signed by ANUJ

laying second layer of Fibre glass cloth when the first layer

is still green. Overlaps of joints of fibre cloth should not be

(b) less than 10 cm.

) third layer of 1.5 mm thickness consisting of slurry of

cement @ 1.289 kg/ sqm mixed with water proofing cement

compound @ 0.670 kg/sqm and coarse sand @ 1.289

kg/sqm. This will be allowed to air cure for 4 hours followed

by water curing for 48 hours. The entire treatment will be

taken upto 30 cm on parapet wall and tucked into groove in

(c) parapet all around.

fourth and final layer of brick tiling with cement mortar

(d) (which will be paid for separately. 54.57 Sqm 688.9 670.30 36,578.25

For the purpose of measurement the entire treated surface

will be measured.

P/F School name Plate including labour, T&P etc all

M.R complete 1 JOB 150000 150000

Digitally signed by ANUJ

BOQ FOR PATHWAY

SNo Item Unit Correction Qty Amount DSR Amount NDSR

Earth work in surface excavation not exceeding 30 cm in

depth but exceeding 1.5 m in width as well as 10 sqm on plan

including getting out and disposal of excavated earth upto 50

2.1 m and lift upto 1.5 m, as directed by Engineer-in- Charge:

4.1 Providing and laying in position cement concrete of specified

grade excluding the cost of centering and shuttering - All work

up to plinth level :

4.1.8 1:5:10 (1 cement : 5 coarse sand (zone-III) derived from

natural sources : 10 graded stone aggregate 40 mm nominal

size derived from natural sources) Cum 6518.60 6342.60 91.02 577298.21

Providing and laying 60mm thick faciory made cement

concrete interlocking paver block of M -30 grade made by

block making machine with strong vibratory compaction, of

approved size, design & shape, laid in required colour and

pattern over and including 50mm thick compacted bed of

coarse sand, filling the joints with line sand etc. all complete

16.68 as per the direction of Engineer-in-charge Sqm 972.00 945.76 910.19 860817.65

Providing and laying at or near ground level factory made

kerb stone of M-25 grade cement concrete in position to the

required line, level and curvature, jointed with cement mortar

1:3 (1 cement: 3 coarse sand), including making joints with or

without grooves (thickness of joints except at sharp curve

shall not to more than 5mm), including making drainage

opening wherever required complete etc. as per direction of

Engineer-in-charge (length of finished kerb edging shall be

measured for payment). (Precast C.C. kerb stone shall be

16.69 approved by Engineer-in-charge). Cum 10117.60 9844.42 18.52 182318.75

Total Cost 1654934.12 0.00

Digitally signed by ANUJ

DSR Rate DSR Amount

SNo Item UOM Correction Qty Amount DSR

Code 2023 NDSR

Excavating, supplying and filling of local earth (including

royalty) by mechanical transport upto a lead of 5km

also including ramming and watering of the earth in

layers not exceeding 20 cm in trenches, plinth, sides of

2.25A foundation etc. complete. Cum 700.50 681.59 456.44 311104.36

Preparation and consolidation of sub grade with power

road roller of 8 to 12 tonne capacity after excavating

earth to an average of 22.5 cm depth, dressing to

camber and consolidating with road roller including

making good the undulations etc. and re-rolling the sub

grade and disposal of surplus earthwith lead upto 50

Supplying and Stacking at Site 90mm to 45 mm size

Supplying and Stacking at Site 63 mm to 45 mm size

Laying, spreading and compacting stone aggregate of

specified sizes to WBM specifications in uniform

thickness, hand picking, rolling with 3 wheeled road/

vibratory roller 8-10 tonne capacity in stages to proper

grade and camber applying and brooming requisite

type of screening / binding material to fill up interstices

of coarse aggregate, watering and compacting to the

16.3 Supplying and stacking at site

16.3.6 Stone screening 13.2 mm nominal size (Type A) Cum 2034.35 1979.42 93.97 186012.77

16.3.7 Stone screening 11.2 mm nominal size (Type B) Cum 2247.75 2187.06 28.19 61657.56

Digitally signed by ANUJ

2.5 cm premix carpet surfacing with 2.25 cum and 1.12

cum of stone chippings of 13.2 mm and 11.2 mm size

respectively per 100 sqm and 52 kg and 56 kg of hot

bitumen per cum of stone chippings of 13.2 mm and

11.2 mm size respectively, including a tack coat with

hot straight run bitumen, including consolidation with

road roller of 6 to 9 tonne capacity etc. complete (tack

16.33 coat to be paid for separately).

With paving Asphalt grade VG - 10 heated and then

mixed with solvent at the rate of 70 grams per kg of

Brick edging in full brick width and half brick depth

including excavation, refilling and disposal of surplus

16.7 earth lead upto 50 metres.

With common burnt clay F.P.S. (non modular) bricks of

Providing and applying tack coat using hot straight run

bitumen of grade VG - 10, including heating the

bitumen, spraying the bitumen with mechanically

operated spray unit fitted on bitumen boiler, cleaning

and preparing the existing road surface as per

Digitally signed by ANUJ

BOQ FOR HORTICULTURE WORKS

DSR Rate Correction

SNo DSR Code Item Unit 2023 Factor Qty Amount DSR AMOUNT NDSR

16.3 Supplying and stacking at site.

2.36 Extra for levelling & neatly dressing of disposed soil completely as

directed by Engineerin- charge Cum 93.05 90.54 564.00 51063.23

2.4 Supplying and stacking at site dump manure from approved source,

including carriage upto 5 km lead complete (manure measured in

stacks will be reduced by 8% for payment) :

2.4.3 Screened through sieve of I.S. designation 4.75 mm cum 287.75 279.98 300.00 83994.23

2.8 Spreading of sludge, dump manure and/or good earth in required

thickness as per direction of officer-in-charge (cost of sludge, dump

manure and/ or good earth to be paid separately). cum 46.15 44.90 300.00 13471.19

2.9 Mixing earth and sludge or manure in the required proportion specified

or directed by the Officer-in-charge cum 32.10 31.23 300.00 9369.99

2.1 Grassing with selection No. 1/ Doob grass including watering and

maintenance of the lawn for 30 days or more till the grass forms a thick

lawn, free from weeds and fit for mowing including supplying good

earth, if needed (the grass and good earth shall be paid for separately).

2.10.1 In rows 5 cm apart in both directions sqm 15.55 15.13 1640.00 24813.45

2.14 Digging holes in ordinary soil and refilling the same with the excavated

earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts

of stacked volume of earth after reduction by 20% : 1 part of stacked

volume of manure after reduction by 8%) flooding with water, dressing

including removal of rubbish and surplus earth, if any, with all leads and

lifts (cost of manure, sludge or extra good earth if needed to be paid for

2.14.3 Holes 60 cm dia, and 60 cm deep Each 39.95 38.87 80.00 3109.71

Digitally signed by ANUJ

2.33 Providing and laying Neelgiri/Mexican grass turf with earth 50mm to

60mm thickness of existing ground prepared with proper level and

ramming with tools wooden (Dhurmos) and than rolling the surface with

light roller make the surface smoothen and light waterning with

sprinkler and maintenance for 30 days or more till the grass establish

properly, as per direction of officer-in-charge. Per Sqm 211.25 205.55 160.00 32887.40

4.91 Providing and Displaying Budded Rose (H.T. variety) 3 to 4 healthy

branch 30 cm and above ht. well developed with one and above flower

plant in 20 cm Earthen Pot, as per direction of the officer-in-charge. Each 32.80 31.91 60.00 1914.86

4.92 Providing and Displaying Creeper Rose variety 3 to 4 healthy branch

60 cm and above ht. well developed with one and above flowers in 25

cm Earthen Pot, as per direction of the officer-in-charge. Each 75.85 73.80 60.00 4428.12

4.93 Providing and Displaying Standard Rose (H.T. variety) 3 to 4 healthy

branch 90 cm and above ht. well developed with one and above

flowers in 25 cm Earthen Pot, as per direction of the officer-in-charge. Each 150.70 146.63 80.00 11730.49

Digitally signed by ANUJ

BOQ Open Air AmphiTheater

Sl. DSR- Description of Item Qty. Unit DSR Rate Rate with Amount Amount NDSR

No. 2023 2023 Correction (In Rs.)

Take Area =421.7Sqm 0.973

1 Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over

areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting

2.6 out and disposal of excavated earth lead upto 50 m and for all lift, as directed by Engineer-incharge.

2 2.25 Filling available excavated earth (excluding rock) in trenches, plinth, sides of oundations etc. in

layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering,

lead up to 50 m and lift upto 1.5 m. 415.7 Cum 196 190.708 79277.3156

3 4.1 Providing and laying in position cement concrete of specified grade excluding the cost of centering

and shuttering - All work up to plinth level :

4.1.8 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate

40 mm nominal size derived from natural sources) 63.14 Cum 6812 6628.076 418496.7186

4 5.1 Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of

centering, shuttering, finishing and reinforcement - All work up to plinth level :

A 5.1.2 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size). 117.16 Cum 9045.75 8801.51475 1031185.468

B 5.2 Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses,

plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth

level up tofloor five level, excluding cost of centering, shuttering, finishing and reinforcement :

5.2.2 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size). 95.76 Cum 10852.95 10559.92035 1011217.973

5 5.22 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and

binding all complete upto plinth level.

5.22.6 Thermo-Mechanically Treated bars of grade Fe-500D or more. 27761 Kg 107.85 104.93805 2913185.206

6 5.9 Centering and shuttering including strutting, propping etc. and removal of form for all heights :

A 5.9.1 Foundations, footings, bases of columns, etc. for mass concrete 71.52 Sqm 392.15 381.56195 27289.31066

B 5.9.2 Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc 470.86 Sqm 842.5 819.7525 385988.6622

Brick work with common burnt clay modular bricks of class designation 7.5 in foundation and plinth

6.2.2 Cement Mortar 1:6 (1 cement : 6 coarse sand). 2.53 Cum 7132.25 6939.67925 17557.3885

Digitally signed by ANUJ

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in

6.4 superstructure above plinth level up to floor V level in all shapes and sizes in :

6.4.2 Cement mortar 1:6 (1 cement : 6 coarse sand) 89.268 Cum 9105.95 8860.08935 790922.4561

11.26 Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement

slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete

with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 529.57 Sqm 1948.25 1895.64725 1003877.914

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average)

thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with

11.27 pigment to match the shade of the slabs, including rubbing and polishing complete 177.203 Sqm 2354.7 2291.1231 405993.8867

Cost for Sqm 8176940.045 0

Digitally signed by ANUJ

Sl. DSR- Description of Item No Qty. Unit DSR Rate Rate with Amount Amount

No. 2023 2023 Correction (In Rs.) DSR (In Rs.) NDSR

Area =476.25 Sqm 0.973

Surface dressing of the ground including removing vegetation and inequalities

not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to

4.1.10 1:5:10 (1 cement : 5 coarse sand (zone-III) derived from natural sources : 10

aggregate 40 mm nominal size derived from natural sources) 1 66.99 Cum 6518.60 6342.60 424890.63

M.R Providing and Fixing Rubber Tile of 600x600 20 mm thick Tile with approved

adhsive as instructed by EIC 1 446.62 Sqm 1740.94 777537.33

M.R Providing, designing and fixing Leg Press Double (250x590x1720) 1 1 Nos 39608.70 39608.70

M.R Providing, designing and fixing Log Cycle (850x550x675) 1 1 Nos 30772.59 30772.59

M.R Providing, designing and fixing Twister Tripple (2074x560x1453) 1 1 Nos 35162.68 35162.68

M.R Providing, designing and fixing of ABS SHAPER DOUBLE /SITUP BENCH DOUBLE

of size 1570mm x1400mmx670mm(Approx) 1 1 Nos 35693.96 35693.96

M.R Providing, designing and fixing of SHOULDER PRESSER SHAPER of size 2188mm

M.R Providing, designing and fixing of AIR SWING WALKER of size 992mm x505mm

M.R Providing, designing and fixing of SHOULDER ARM WHEEL of size 1350mm x

Digitally signed by ANUJ

M.R Providing, designing and fixing of BACK EXTENSION of size 1220mmX 790mm X

M.R Providing, designing and fixing of PARALLEL BARS of size 1600mm X 330mm X

M.R Providing, designing and fixing of HORSE RIDER of size 850mm x 550 mm x 675

M.R Providing & fixing ARM AND PADDLE, BIKE DIMENSIONS:- 1100mm (Length) x

500mm (Width) x 900mm (Height). SAFE AREA:- 2000mm (Length) X1000mm

M.R Providing, designing and fixing of CHEST PRESSER SHAPER of size 1725mm

M.R Providing & fixing SEATED PULLER /PULL CHAIR made from “C” Class G.I pipe.

DIMENSIONS: – 1900mm (Length) x 740mm (Width) x 1920mm. (Height). SAFE

M.R Providing & fixing SKY WALKER DIMENSIONS: – 1720mm (Length) x 630mm

(Width) x 1750mm.(Height) SAFE AREA: – 2.7Mtr x 1.6Mtr. Sky Walker 1 1 Nos 60119.09 60119.09

M.R Providing & fixing CROSS TRAINER / ELLIPTICAL EXERCISER DIMENSIONS: –

1320mm (Length) x 600mm (Width) x 1750mm. (Height). SAFE AREA: – 1.77 x

M.R Providing & fixing SURF BOARD Providing and fixing Surf Board made from “C”

Class GI pipe. 1 1 Nos 60119.09 60119.09

Total of Open Gym 440166.82 1538589.13

Digitally signed by ANUJ

BOQ MINI INTEGRATED SPORTS COMPLEX

Sl. DSR- Description of Item Qty. Unit DSR Rate Rate with Amount Amount

No. 2023 2023 correction (In Rs.) DSR (In Rs.) NDSR

(In Rs.) factor

1 Preparation and consolidation of sub grade with power road roller of

8 to 12 tonne capacity after excavating earth to an average of 22.5 cm

depth, dressing to camber and consolidating with road roller including

making good the undulations etc. and re-rolling the sub grade and

16.1 disposal of surplus earthwith lead upto 50 metres. 1216 Sqm 218.90 212.99 258995.48

2 16.3.2 63 mm to 45 mm size stone aggregate 91.2 Cum 1636.05 1591.88 145179.15

3 16.3.3 53 mm to 22.4 mm size stone aggregate 91.2 Cum 1842.30 1792.56 163481.28

4 16.3.6 Stone screening 13.2 mm nominal size (Type A) 60.8 Cum 2034.35 1979.42 120348.89

5 16.3.7 Stone screening 11.2 mm nominal size (Type B) 60.8 Cum 2247.75 2187.06 132973.29

8 Laying, spreading and compacting stone aggregate of specified sizes

to WBM specifications in uniform thickness, hand picking, rolling with

3 wheeled road/ vibratory roller 8-10 tonne capacity in stages to

proper grade and camber, applying and brooming requisite type of

screening / binding material to fill up interstices of coarse aggregate,

16.4 watering and compacting to the required density . 425.6 Cum 1046.95 1018.68 433551.21

9 Providing and laying C.C. pavement of mix M-25 with ready mixed

concrete from batching plant. The ready mixed concrete shall be laid

and finished with screed board vibrator , vacuum dewatering process

and finally finished by floating, brooming with wire brush etc.

complete as per specifications and directions of Engineer-in-charge.

16.75 (The panel shuttering work shall be paid for separately).

(Note:- Cement content considered in this item is @ 330 kg/cum.

Excess/less cement used as per design mix is payable/ recoverable

10 Steel reinforcement for R.C.C. work including straightening, cutting,

bending, placing in position and binding all complete upto plinth

11 5.22.6 Thermo-Mechanically Treated bars of grade Fe-500D or more. 4864 Kg 107.85 104.94 510418.68

12 M.R Acrylic Flooring consisting of 8 Layers System

1st Layers of Re surface

5 Layers of Cushion

Digitally signed by ANUJ

2 Layers of Colour

13 M.R Line Marking as per International Standard 1080 Sqm 953.21 1029469.23

14 M.R Hand Opetrated Hydraulic Movable Basket Ball System with 20 mm

thick Transparent acrylic board with Double die Made Farme

Aluminium anodized with built in bracket for mounting , Dunking Rim,

3.2 mtr Projection from the base Pole Special non marking wheels,

Hand Operated Hydraulic system for East lifiting and bringing down

the backboard in a folded position as shown 1 Pair 730516.89 730516.89

15 M.R Hand Ball Goal Post Poles (3 mtr width 2.0 mtr Ht ) Front Facia of 80

mm Dia of M.S Pipe 3.2m +-1 mm , wall Thickness , with Rear pipes of

40/mm dia with hook for holding nets at rear along with wheels All

Premiered & Painted along with Hand balls net 1 Pair 44200.00 44200.00

16 M.R Volleyball Poles Basic Model with over lapping system for Ht

adjustment volleyball net plastic Coated steel wire net antenna for

Fiber glass 2 Pair 35204.62 70409.25

17 M.R Line Marking for Badminton court onKota stone Flooring as per

International Rules with Paint 1 Pair 25166.13 25166.13

18 M.R Installation Charges 1 Pair 39728.71 39728.71

19 M.R Transporation 1 Pair 20000.00 20000.00

DSR Chain Link Fencing:3 mtr Ht 480

20 2.6 Earth work in excavation by mechanical means (Hydraulic

excavator)/manual means over

areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on

plan) including getting

out and disposal of excavated earth lead upto 50 m and for all lift, as

directed by Engineer-incharge. 28.8036 Cum 177.50 172.71 4974.60

21 2.6.1 All kinds of soil

22 4.1 Providing and laying in position cement concrete of specified grade

excluding the cost of

centering and shuttering - All work up to plinth level :

23 4.1.10 1:5:10 (1 cement : 5 coarse sand (zone-III) derived from natural

sources : 10 graded stone

aggregate 40 mm nominal size derived from natural sources) 4.85394 Cum 6518.60 6342.60 30786.59

24 4.1.3 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources

: 4 graded stone

aggregate 20 mm nominal size derived from natural sources) 19.4691 Cum 7878.50 7665.78 149245.85

Digitally signed by ANUJ

25 10.16 Steel work in built up tubular (round, square or rectangular hollow

tubes etc.) trusses etc.,

including cutting, hoisting, fixing in position and applying a priming

coat of approved steel

primer, including welding and bolted with special shaped washers etc.

26 10.16.3 Electric resistance or induction butt welded tubes 4502.4294 Kg 194.40 189.15 851639.92

27 16.71 Providing and fixing G.I. chain link fabric fencing of required width in

mesh size 25x25 mm

made of G.I. wire of dia 3 mm including strengthening with 2 mm dia

wire or nuts, bolts and

washers as required complete as per the direction of

Engineer-in-charge. 480.06 Sqm 1149.25 1118.22 536812.81

13.5 Applying priming coat:

28 13.50.3 With ready mixed red oxide zinc chromate primer of approved brand

and manufacture on steel

galvanised iron/ steel works 960.12 Sqm 67.40 65.58 62964.86

29 13.61 Painting with synthetic enamel paint of approved brand and

manufacture to give an even

30 13.61.1 Two or more coats on new work 960.12 Sqm 155.90 151.69 145641.27

Digitally signed by ANUJ

Sl. DSR- Description of Item Unit Qty. Rate DSR Rate with Amount DSR Amount NDSR

No. 2023 (In Rs.) correction (In Rs.) (In Rs.)

B Brick drain chennal (230W x 150 avg depth ) 0.973

Earth work in excavation by mechanical means

(Hydraulic excavator) / manual means in foundation

trenches or drains (not exceeding 1.5 m in width or 10

sqm on plan), including dressing of sides and ramming

of bottoms, lift upto 1.5 m, including getting out the

excavated soil and disposal of surplus excavated soil as

1 2.8 directed, within a lead of 50 m.

2 2.8.1 All kinds of soil

3 2.25 Filling available excavated earth (excluding rock) in

trenches, plinth, sides of oundations etc. in layers not

exceeding 20cm in depth, consolidating each

deposited layer by ramming and watering, lead up to

4 4.1 Providing and laying in position cement concrete of

specified grade excluding the cost of centering and

shuttering - All work up to plinth level :

5 1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded

4.1.8 stone aggregate 40 mm nominal size)

7 Brick work with common burnt clay F.P.S. (non

modular) bricks of class designation 7.5 in foundation

6.1 and plinth in:

8 6.1.2 Cement mortar 1:6 (1 Cement : 6 coarse sand)

Digitally signed by ANUJ

10 Cement plaster 1:3 (1 cement: 3 coarse sand) finished

13.9 with a floating coat of neat cement.

11 13.9.1 12 mm cement plaster

13 Providing and fixing factory made precast RCC

perforated drain covers, having concrete of strength

not less than M-25, of size 1000 x 450x50 mm,

reinforced with 8 mm dia four nos longitudinal & 9 nos

cross sectional T.M.T. hoop bars, including providing 50

mm dia perforations @ 100 to 125 mm c/c, including

providing edge binding with M.S. flats of size 50 mm x

1.6 mm complete, all as per direction of

23.9 Engineerin-charge

14 Providing and laying cement concrete in retaining

walls, return walls, walls (any thickness) including

attached pilasters, columns, piers, abutments, pillars,

posts, struts, buttresses, string or lacing courses,

parapets, coping, bed blocks, anchor blocks, plain

window sills, fillets, sunken floor etc., up to floor five

level, excluding the cost of centering, shuttering and

15 1:1½:3 (1 cement : 1½ coarse sand (zone-III) derived

from natural sources : 3 graded stone aggregate 20

4.2.2 mm nominal size derived from natural sources).

Digitally signed by ANUJ

BOQ For Running Track

Sl. DSR- Description of Item Unit Qty. DSR Rate Rate with Amount Amount

No. 2023 2023 correction (In Rs.) DSR (In Rs.) NDSR

(In Rs.) factor

Take Area = 1038.59Sqm 0.973

Excavating, supplying and filling of local earth (including

royalty) by mechanical transport upto a lead of 5km also

including ramming and watering of the earth in layers not

exceeding 20 cm in trenches, plinth, sides of foundation etc.

Digitally signed by ANUJ

SUMMARY OF EXTERNAL ELECTRICAL WORK

S. No. Description of item

Schedule Item DSR - 2022 Non-Schedule Item

A MAIN LT PANEL 1,467,235

B CAPACITOR PANEL 313,753

C ESSENTIAL PANELS 547,135

D FEEDER PANELS 2,189,426

F EARTHING 368,143 0

G EXTERNAL LIGHTING 0 1,103,984

H 11 KV HT STRUCTURE 286,471

I TRANSFORMER 2,319,726

J DG SET 3,042,037

K LT PANELS 4,578,056

GRAND TOTAL 21,758,268

GRAND TOTAL 21,758,268

Digitally signed by ANUJ

BOQ External Electrical Work

DSR rate with GST DSR rate with

S.No. Description of Items Unit Qty DSR Rate 2022 factor correction factor

DSR-Amount NSR Rate NSR-Amount Remarks

A MAIN LT PANEL

Design, manufacture, supply inspection, instalation, handling, assembling,

affecting proper connections, testing and commissioning of 14 SWG CRCA

sheet steel fabricated cubical type Main L.T. Panel, floor mounting, dust &

vermin proof, front operated construction, enclosure class - IP 52, powder

coated after proper treatment with 9 tank process with top/bottom

removable gland plates, as required, double compression type cable

MR 1 glands, earth bus, hinged and lockable doors to achieve dust and vermin

proof complete with all inter connections small wiring by min. 2.5 sq. mm.

FRLS copper wires, ckt labels etc. The Aluminium Bus Bar shall be of suitable

length, 500 volts, 3 phase 50 Hz TPN, electrolytic aluminium as per IS 8623 .

The panel feeders shall be suitable for terminating suitable up to 3.5 / 4

core 300 sq mm armoured aluminium cable or Aluminium Bus Duct as

All incoming / bus coupler MCCB shall be microprocessor based with O/L

& S/C and E/F protection and all Outgoings MCCB's may be

thermo-magnetic based O/L & S/C protection.

All MCCB's shall be Ics = 100% Icu, with rotary handle & pad locking

arrangement, with trip setting as per load requirement. All TP MCCB shall

be with heavy duty solid isolable neutral link.

The breaking capacity specified for breakers is Ics value (service rating).

The instrument chamber shall be separate and shall comprise of flush type

ammeter, voltmeter, selector switches, cast resin type CT's & PT's, etc.

Separate CT's shall be provided for protective and measuring system.

All Energy Analyser / TVM Shall have RS 485 Modbus RTU on board

Communication protocol for SCADA communication.

The fault withstanding capacity of panel & its control gear shall be min. 25

KA rms for 1 sec.

GA drawings shall be got approved from Owners / Architects / Consultants

before fabrication.The panel has to be specifically fabricated as per the

space available at Stilt level.

It shall be electrically & Mechanically interlocked with both incoming & Bus

coupler's contactor in such a way that at any one time two supply should

not get mixed up.

i. 1 nos 400 AMP FP MCCB of 35 KA with following accessories

ii. Metering for incomers

iii. 1 nos. Under voltage relay with timer.

iv. 0-500 volt range voltmeter with selector switch (P.T. connected)

1 set of 3 CT's of ratio 400/5A, Class 1.0 accuracy 15 VA burden for

1 set of 3 CT's of ratio 400/5A, Class 1.0 accuracy 15 VA burden for APFCR.

1 nos. Energy analyser (digital type) consisting of I, V, KW, KWH, KVA, PF, HZ,

MDI (EM 6400 of Conzerve or equi.) with RS 485 communication port for

communication / report generation.

Digitally signed by ANUJ

BOQ External Electrical Work

DSR rate with GST DSR rate with

S.No. Description of Items Unit Qty DSR Rate 2022 factor correction factor

DSR-Amount NSR Rate NSR-Amount Remarks

Power factor meter.

Frequency meter.

Indications for incomers

3 Nos. LED type phase indicating lamps, each lamp shall be with bakup

1 nos. 400 Amps FP MCCB Bus coupler (35 KA)

It shall be electrically & Mechanically interlocked with both incoming & Bus

coupler's contactor in such a way that at any one time two supply should

not get mixed up.

3 Nos. LED type phase indicating lamps, 3 Nos. LED type indicating lamps

for indicating the status of feeder - ON / OFF / TRIP. each lamp shall be

with bakup HRC fuse/MCB.

1 section of 500 AMP , 415 Volts, 3 phase 50 HZ TPN high conductivity

electrolytic Aluminium bus bar of suitable length, SMC / DMC supports, with

colour coading and insulated by heat shrinkable sleeves and clip on

shrouds for joints.

The current density of bus bar up to 400 Amp shall be minimum 1.00 sq mm

The Maximum allowable temperature for the Bus bar to be restricted to 85

deg C. The temperature rise should be restricted to 35 deg C above

design ambient temperature of 50 deg C.

All outgoing feeders shall be provided with one set of phase indication

lamps and trip indication lamps with protection fuses/MCB and ammeter

with selector switch with suitable ratio CT's of accuracy class 1.0

4 No. 300 amps 4P MCCB 35kA outgoing feeder .

2 No. 200 amps 4P MCCB 35kA outgoing feeder

2 No. 200 amps 4P MCCB 35kA outgoing feeder

2 No. 250amps 4P MCCB 35kA outgoing feeder .

2 No. 100amps 4P MCCB 35kA outgoing feeder .

TOTAL CARRIED TO SUMMARY Set 1 1,467,235 1,467,235

B CAPACITOR PANEL

Digitally signed by ANUJ

BOQ External Electrical Work

DSR rate with GST DSR rate with

S.No. Description of Items Unit Qty DSR Rate 2022 factor correction factor

DSR-Amount NSR Rate NSR-Amount Remarks

Design, manufacture, supply, inspection, handling, assembling, affecting

proper connections, testing and commissioning of 14 SWG CRCA sheet

steel fabricated cubical type 100 KVAR A P F C Panel consisting of 5 / 10 /

15 / 20 / 25 / 50 KVAR capacitor units in tier formation, housed in an

integrated cubicle type automatic switching ON and OFF control panel,

floor mounting, dust & vermin proof, front operated construction, enclosure

MR 2 class - IP 52, powder coated after proper treatment with 9 tank process

with top/bottom removable gland plates, as required, double compression

type cable glands, earth bus, hinged and lockable doors to achieve dust

and vermin proof complete with all inter connections small wiring by min.

2.5 sq. mm. copper wires, ckt labels etc. The Aluminium Bus Bar shall be of

suitable length, 500 volts, 3 phase 50 Hz TPN, electrolytic aluminium as per

The incoming MCCB shall be microprocessor based with inbuilt O/L & S/C

release with E/F protection and All outgoings MCCB's shall be

thermal-magnetic based with inbuilt O/L & S/C release.

All MCCB's shall be Ics = 100% Icu, with rotary handle & pad locking

arrangement, with adjustable O/L & S/C trip setting as per load

requirement. All TP MCCB's shall be with AC 3 duty contactor for neutral

isolation. All TP MCCB shall be with heavy duty solid isolable neutral link. The

breaking capacity specified is Ics value. The instrument chamber shall be

separate and shall comprise of flush type ammeter, voltmeter, selector

switches, CT's, PT's, etc

Capacitor duty contactors should be used for switching individual

capacitor banks.

The fault withstanding capacity of panel & its control gear shall be min. 35

KA rms for 1 sec.

Each section of capacitor panel shall have Verticle hood & exhaust fans

for ventilation purpose.

The maximum height of the panel should not exceed 2100 mm unless

specifically approved.

The capacitor panel shall be integrated with the main L T Panel as per

schematic diagram.

1 no. 200 AMP. FP, MCCB with heavy duty solid neutral link, with O/C , S/C,

E/F protection, adjustable thermal magnetic release, 35 KA Breaking

1 set- 3 CTs , ratio 200/5A Class 1.0 accuracy 15 VA burden for metering.

1Nos- (0-250A) digital Ameter with selector switch

Micro processor based automatic power factor control relay (3 phase)

(including power factor meter) in 16 steps for automatic cut off or add on

capacitor units to keep the power factor at 0.95 with variation of loads. All

associated auxiliary contactors / relays shall be provided with in the scope

Phase indicating lamps with HRC fuses, and indicating in each capacitor

chamber unit to indicate On/Off status of capacitor unit.

Digitally signed by ANUJ

BOQ External Electrical Work

DSR rate with GST DSR rate with

S.No. Description of Items Unit Qty DSR Rate 2022 factor correction factor

DSR-Amount NSR Rate NSR-Amount Remarks

250 AMP, 500 Volts, 3 phase 50 HZ TPN high conductivity electrolytic

Aluminium bus bar of suitable length, SMC / DMC supports, with colour

coding and insulated by heat shrinkable sleeves and clips on shrouds for

joints. The current density of bus bar shall be minimum 1.00 sq mm / amp.

The Maximum allowable temperature for the Bus bar to be restricted to 85

deg C. The temperature rise should be restricted to 35 deg C above

ambient temperature.

1 no. of 125 AMPS TPN 35 KA MCCB and 80 amps AC3 duty contactor with

50 KVAR gas filled 415 V capacitor bank, auto-manual selector switch, start

stop push button for manual operation including on/off indicating lamps

and delay timer complete.

1 no. of 63 AMPS TPN 35 KA MCCB and 80 amps AC3 duty contactor with

20 KVAR gas filled 415 V capacitor bank, auto-manual selector switch, start

stop push button for manual operation including on/off indicating lamps

and delay timer complete.

2 no. of 63 AMPS TPN 35 KA MCCB and 80 amps AC3 duty contactor with

10 KVAR gas filled 415 V capacitor bank, auto-manual selector switch, start

stop push button for manual operation including on/off indicating lamps

and delay timer complete.

2 no. of 25 AMPS TPN 35 KA MCCB and 32 amps AC3 duty contactor with 5

KVAR gas filled 415 V capacitor bank, auto-manual selector switch, start

stop push button for manual operation including on/off indicating lamps

and delay timer complete.

TOTAL CARRIED TO SUMMARY Set 2 156,877 313,753

C ESSENTIAL PANELS

MR 3 ESSENTIAL PANELS

Design, manufacture, supply inspection, instalation, handling, assembling,

affecting proper connections, testing and commissioning of 14 SWG CRCA

sheet steel fabricated cubical type Essential Panel, floor mounting, dust &

vermin proof, front operated construction, enclosure class - IP 52, powder

coated after proper treatment with 9 tank process with top/bottom

removable gland plates, as required, double compression type cable

glands, earth bus, hinged and lockable doors to achieve dust and vermin

proof complete with all inter connections small wiring by min. 2.5 sq. mm.

FRLS copper wires, ckt labels etc. The Aluminium Bus Bar shall be of suitable

length, 500 volts, 3 phase 50 Hz TPN, electrolytic aluminium as per IS 8623 .

The panel feeders shall be suitable for terminating suitable up to 3.5 / 4

core 300 sq mm armoured aluminium cable or Aluminium Bus Duct as

200 amps TP+N MCCB with following accessories:

Digitally signed by ANUJ

BOQ External Electrical Work

DSR rate with GST DSR rate with

S.No. Description of Items Unit Qty DSR Rate 2022 factor correction factor

DSR-Amount NSR Rate NSR-Amount Remarks

Metering & Indication

1 set of R,Y,B phase indicating lamps each with 3 nos. 6A SP MCBs.

Phase indicating light shall be protected by 6A MCB. - 1 Set

1 Set of 300A TPN Aluminium Bus Bar with colour coded PVC Sleeves

1 no's 200 amps TP+N MCCB with following accessories:

EXTERNAL LIGHTING FEEDER PILLAR _ described as above Set 2 273,568 547,135

D FEEDER PILLAR'S

MR 4 ESSENTIAL LIGHTING FEEDER PILLAR

Design, manufacture, supplying fixing in position of outdoor type feeder

pillar, metal clade, suitable for 415 volt, 3-phase, 50 Hz with suitable

foundation and arrangement for incoming/ outgoing cable termination,

earthing, locking arrangement, insulated aluminium bus bars system,

interconnection etc. also with Astronomical Timers for Auto switching-

ON/OFF of External road Lightings.

200 amps TP+N MCCB with following accessories:

Metering & Indication

1 set of R,Y,B phase indicating lamps each with 3 nos. 6A SP MCBs.

Phase indicating light shall be protected by 6A MCB. - 1 Set

1 Set of 300A TPN Aluminium Bus Bar with colour coded PVC Sleeves

63A DP MCB -14 No.

25A FP MCB -4 No.

EXTERNAL LIGHTING FEEDER PILLAR _ described as above Set 2 300,851 601,701

MR 5 BUILDING FEEDER PANEL-1

BUILDING FEEDER PANEL-1( SCHOOL BUILDING,Multi purpose hall, Temple)

Design, manufacture, supplying fixing in position of the following front

operated cubicle type, front access, dead back, 2mm thick steel enclosed

free standing, dust and vermin proof, switchboard with IP52 protection with

hinged and lockable doors complete with interconnections, tinned

copper/Al crimping lugs, bonding to earth and painting, suitable for use at

415 volts, 3 phase 4 wire 50 Hertz system, and suitable for a fault level of 35

kA symmetrical at 415 volts . It should be complete with in all respects as

per techinical specifications.

Digitally signed by ANUJ

BOQ External Electrical Work

DSR rate with GST DSR rate with

S.No. Description of Items Unit Qty DSR Rate 2022 factor correction factor

DSR-Amount NSR Rate NSR-Amount Remarks

1No. 300 amps 4P 36 kA, Moulded Case Circuit Breaker with TM release

Digital electronic VAF meter with and 300/5 Amps 5 VA, CL 1 CTs . - 1 Set

Additional earth fault protection will be provided in all incoming MCCBs.

Metering & Indication

1 set of R,Y,B phase indicating lamps each with 3 nos. 6A SP MCBs.

Phase indicating light shall be protected by 6A MCB. - 1 Set

400 Amps 4 Pole 36 kA for 1 sec. Alumminium bus bars with heat coloured

shrinkable insulation sleeve. - 1 Set

2 No. 250 amps 4 Pole MCCB 36kA outgoing feeder.

2 No. 63 amps 4 Pole MCCB 25kA outgoing feeder.

BUILDIN FEEDER PILLAR-1_as described above. Set 1 337,819 337,819

MR 6 BUILDING FEEDER PANEL-2

BUILDING FEEDER PANEL-2 (Principal Residence, Vice Principal Residence

& Guest house, Kitchen , Guard room)

Design, manufacture, supplying fixing in position of the following front

operated cubicle type, front access, dead back, 2mm thick steel enclosed

free standing, dust and vermin proof, switchboard with IP52 protection with

hinged and lockable doors complete with interconnections, tinned

copper/Al crimping lugs, bonding to earth and painting, suitable for use at

415 volts, 3 phase 4 wire 50 Hertz system, and suitable for a fault level of 35

kA symmetrical at 415 volts . It should be complete with in all respects as

per techinical specifications.

1No. 300 amps 4P 36 kA, Moulded Case Circuit Breaker with TM release

Digital electronic VAF meter with and 300/5 Amps 5 VA, CL 1 CTs . - 1 Set

Digitally signed by ANUJ

BOQ External Electrical Work

DSR rate with GST DSR rate with

S.No. Description of Items Unit Qty DSR Rate 2022 factor correction factor

DSR-Amount NSR Rate NSR-Amount Remarks

Additional earth fault protection will be provided in all incoming MCCBs.

Metering & Indication

1 set of R,Y,B phase indicating lamps each with 3 nos. 6A SP MCBs.

Phase indicating light shall be protected by 6A MCB. - 1 Set

400 Amps 4 Pole 36 kA for 1 sec. Alumminium bus bars with heat coloured

shrinkable insulation sleeve. - 1 Set

1 No. 250 amps 4 Pole MCB 36kA outgoing feeder.

4 No. 150 amps 4 Pole MCB 36kA outgoing feeder.

BUILDIN FEEDER PILLAR-2_as described above. Set 1 337,819 337,819

MR 7 BUILDING FEEDER PANEL-3

BUILDING FEEDER PANEL-3 (Boys Warden Residence, Boys Dormitiory)

Design, manufacture, supplying fixing in position of the following front

operated cubicle type, front access, dead back, 2mm thick steel enclosed

free standing, dust and vermin proof, switchboard with IP52 protection with

hinged and lockable doors complete with interconnections, tinned

copper/Al crimping lugs, bonding to earth and painting, suitable for use at

415 volts, 3 phase 4 wire 50 Hertz system, and suitable for a fault level of 35

kA symmetrical at 415 volts . It should be complete with in all respects as

per techinical specifications.

1No. 250 amps 4P 36 kA, Moulded Case Circuit Breaker with TM release

Digital electronic VAF meter with and 250/5 Amps 5 VA, CL 1 CTs . - 1 Set