PROVN OF STEEL WIRE MESH IN BLDG No. 47 OF 298 FD WKSP, PROVN OF MT SHED FOR VEHICLES AT 1872 RKT REGT, REPLACEMENT OF DOORS AND WIRE MESH IN BLDG NO 57, 83, 91, 93 AND 119 OF RKT REGT AND PROVN OF FALSE CEILING AND ALUMINIUM CUBICLES PARTITION

Amount

M&L for wire netting of galvanised steel wire 1.40mm dia, size of mesh 20mm, fixed with angle iron frame with flat iron including necessary welding as in bird proofing net, complete, all as specified and directed by the Engr-In-Charge. Note: Angle iron/FI frame shall be measured and paid separately under respective item. Work to be carried out up to 8m height. Cost of all scafolding, ladders required for the work shall be deemed to be included in the quoted rates of tenderer.

S&F mild steel framed work as in doors / gates / steel frames / chowkats etc. of angle or other section with gusset plates, rails, braces, etc., complete conforming to Grade E-165 (Fe 290), drilled for fixing of wire netting or other covering including necessary welding etc and fixing in position complete.

M&L for preparation of new steel surfaces n exc 10cm width or grith & applying two coats of synthetic enamel paint of 1st quality over a coat of red oxide primer complete all as specified & directed.

Surface excavation over areas n.exc 30 cm deep and average 15 cm deep , in soft loose soil complete all as specified and directed.

Excavation in trenchs not exc1.5 m wide and not exc 1.5 m in depth for foundation etc or for shafts wells, cesspits, manhole, laying cables etc n exc 10 Sq m on plan, complete in hard / dense soil all as specified and directed.

M&L for PCC 1:4:8 type D-2 (using 40mm thick crused stone aggregate) as in fdn filling and mass concrete complete all as specified and directed.

Excavation in post holes (or similar holes) each n exc 0.5 cum, getting out, returning filling in and ramming earth or broken rubble mixed with earth around, in layers n exc 25 cm, watering and removing surplus soil to a distance n exc 50 m and making good surface in hard/dense soil complte all as specified and directed.

M&L for PCC 1:3:6 type C2(using 40mm thick crused stone aggregate) as in fdn for vertical post all specified and directed..

M&L for hard core of gauge n exc 63 mm broken stone or bouilder deposited spread & levelled in layers n exc 15 cm thick watered rammed to a true surface all as specified and directed.

M&L for 75mm thick PCC 1:4:8 type D-2 (using 40mm graded stone aggregate) as in sub base of floors, complete all as specified and directed.

M&L for 40mm thick PCC 1:2:4 type B-1 (using 20mm graded crushed stone aggregate ) as in floors, finished even and smooth without using extra cement, complete all as specified

Supply only glass dividing stirrups 3mm thick, 38 mm width inserted in position confirm to design.

M&L for 75 mm thick PCC 1:3:6 type C2 using 40 mm graded crushed stone aggregate as in plinth protection surface finished fair and even complete all as specified. Note :- Plinth protection shall be of width as directed and shall be laid to slope of 1:30 in alternative bays not exceeding 3 meter in length. Joints of 6 mm wide and 10 mm deep shall be provided along the wall and bays and same shall be filled with bitumen mastic (1:3).

All as per item No. 13.00 above but 50mm thick plinth protection with PCC 1:3:6 type C1 using 20 mm graded crushed stone aggregate

Returning, filling in including watering and well ramming in layers not exc 25 cm completed all as specified and directed.

Removal of excavated materials (soils) n exc 50 m and deposited whereas directed at a level not exc 1.50 m above the starting point complete all as directed

S&F mild steel framed work using ERW or induction butt welded tubes conforming to I.S 1161-1979 Grade St-240 including necessary welding, bolting, special shaped washer, clamps, cleats etc. complete all as specified & as directed.

S&F rolled mild steel work as in Plates (plain or chequered) channels. Square cut or notched (ordinary and counter sunk) forming holes, without any attachment including necessary welding etc. conforming to Gde E-250 (Fe 410-W) quality `A’ all as specified and as directed.

S&F Pre-painted galvalume aluminium zinc coating GI based courrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screw fixed with L & J hooks and washer in roof wall etc with grade of zink coating 275 completed all as specified and directed.

S&F Pre-painted galvalume aluminium zinc coating GI based plain steel shet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screw completed all as specified and directed.

M&L for MS bolts 12 mm dia machine made with hexagonal or squared heads at one end and screwed and to be fitted with washers and one hexaonal or squared but n exc 5 cm long complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) n exc 1.50 sqm each and removing from site complete all as specified & directed and making good disturbed surface of walls in cement mortar (1:3) all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) exc 1.50 sqm and n.exc 4.00 Sqm each and removing from site complete and making good disturbed surfaces of wall in CM (1:3) all as specified and directed.

M & L for rolled mild steel work angle iron as in door frame (Chowkhats) & cooler stand including provn of 12mm dia deformed bar welded horizontally to bottom of frame confirming to Fe-290 or Fe-330 including preparing back of chowkhat and applying two coats tar and sanding newly tarred surfaces with clean sharp sand complete all as specified and directed.

S & F factory made solid pannel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rail. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail & bottom rail on either side and as gap insert for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded. sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement, supplying and fixing in the frame at site as per specification and drawings on page 146 of SSR Part - II 2004 complete all as specified and directed.

S & F for 2nd class HW 35 mm thick, gauged and skeleton shutters (Three Panels), factory made open rebated and prepare to receive glass, gauge etc (with sash bar), edges of framing plain, chamfered or rounded, fitted with cut & mitred beads for securing glass etc. Size of members of shutter shall be as specified in SSR 2009 Part-I, section 8 clause Member shall be kiln seasoned as per IS-1141 & chemically pressure treated as per IS-401 complete all as specified and directed.

S&F Steel window/ ventilator glazed and gauged (combination) with side hung/ top hung shutters incl box type / projecting type hinges, and steel peg stay, handle & locking arrangement and frame made out of 1.25mm thick pressed steel frame complete incl necessary AC/Cooler arrangement in window & guard bars complete all as as specified and directed.

S & F 300mm long aluminium alloy,anodised, sliding door bolts with hasps, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and directed.

S & F extruded aluminium handle fabricated type, anodised 150mm size conforming to IS complete all as specified and directed.

S&F aluminium, anodised, barrel tower bolt of extruded section, ISI marked, 150 mm long complete all as specified and directed.

S & F 125mm double action spring hinges,mild steel with steel wire spring, stove enaelled black, complete all as specified and directed.

S&F mild steel butt hinges, medium weight, cold rolled, ISI marked of size 100 mm, complete all as specified and directed.

S&F stainless steel wire cloth 0.36mm nominal dia of wire & average width of aperture 1.40mm & fixed with wire staples complete all as specified& directed.

M & L for preparation of new wooden surface over 10cm width or girth and applying two coats of synthetic enamel paint of Ist quality over a coat of pink primer complete all as specified and directed.

S&F 3.00 mm thick sheet glass, ordinary / figured quality & glazing with oil putty not exc 0.50 Sqm each pane complete all as specified& directed.

M&L for powder coated anodised aluminium frames for doors, windows, ventilators and partation with one or more rebates including jointing cleats for fixing etc complete all as specified and directed.

M&L for 12mm thick prelaminated particle board exterior grade prelaminated both sides with decorative choice laminations.

M&L powder coated anodised aluminium door shutters, aluminium section weighing 0.55 Kg/m including necessary joining cleat, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminium snap beading screws etc complete all as specified.

S&F door closer aluminium extruded section hydraulically regulated designation No. 3 universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed.

M&L for 4.8 mm thick sheet glass, ordinary quality fixed to aluminum frame work and glazing with suitable size aluminum anodised beading exc 0.5 Sqm in each pane all as specified and directed.

S&F Mortice locks Brass vertical type size 100mm 4 levers brass chromium plated with keys in duplicate all as specified and directed.

S&F Aluminium anodised barrel tower bolts of extruded section 200mm long all as specified and directed.

M & L for roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. compete all as specefied and directed by E-in-Charge. (Fe- 410W Grade-E-250 quality A).

Cutting holes in brick / stone wall exc half brick but n exc one brick built in cement mortar or in cement lime mortar for inserting angle iron and making good dismantled portion in cement concrete 1:2:4 type B-1 as required complete all as specified and directed

Providing & Fixing false ceiling with fibre Cement Designer tile Ivory painted (High Pressure Steam Cured) of 4mm thickness (as per IS:14862) of size 595x595 mm and any one of the design (oceanic, lake & hill, cascade or electra) in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections (galvanized @ 120 gms, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and 15x32 mm made from 0.30 mm thick sheet, spaced at 1200 mm c/c and cross "T" of size 15x32 mm made of 0.30 mm sheet, 1200mm long spaced between main "T" at 600 mm c/c to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size15x32 mm made of 0.30 mm thick sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 15x20 mm made of 0.30 mm thick sheet and laying false ceiling tiles in the grid including , required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI soffit cleats fixed to existing RCC lintel with dash fasteners, GI adjustable rods of 3mm dia with galvanised Butterfly level clips, spaced at 1200 mm c/c along main T, bottom exposed width of 15mm of all T -sections shall be centra black pre-painted with polyester paint, and having a load bearing capacity of 12 kg/sqm, all complete at all heights as per direction of Engineer-in-charge.

M & L for Solid PVC Wall Lining consisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing complete all as specified and directed.

S&F 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing and complete all as specified and directed.

M&L for brick work with old size fly ash bricks bricks staright or curved on plan exc 6m mean radius built in CM 1:6 complete all as specified and directed.

M&L for brick work with old size fly ash bricks staright or curved on plan to any radius in half brick thick walls built in CM 1:4 complete all as specified and directed.

M&L for 40mm thick PCC 1:2:4 type B0 using 12.5mm graded crushed stone aggregate as in damp proof course on horizontal surface using water proofing compound including necessary formwork. Note : - Supply only water proofing compound shall be measured and paid for separately.

M & L for Non - skid Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including screed bed or bedding layer 15 mm thick in CM (1:6) over and including 25 mm thick PCC (1:2:4) type B-1 using 20 mm graded stone aggregate complete all as specified and directed.

All as per above item No. 51.00 above but on vertical surfaces of wall such as dados, skirting etc set & jointed in neat slurry and pointed in white or colour cement to match over 10mm thick screed plaster in CM 1:4 complete all as specified & directed..

M&L glazed ceramic coloured tiles, size 450 mm X 300 mm, 6-7 mm thick on vertical surfaces of wall such as dados, skirting etc set & jointed in neat slurry and pointed in white or colour cement to match over 10 mm thick screed plaster in CM 1:4 complete all as specified and directed.

M & L for 20mm thick black granite on kitchen platform and similar work over & including 15mm thick screed bed in CM 1:6 laid over sand stone slab machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including cutting and polishing complete all as specified & directed.

M & L for mild steel TMT bars of 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed by the Engineer-in-Charge

M & L for mild steel TMT bars 5mm dia and over upto including 10mm dia in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed by the Engineer-in-Charge

M & L for RCC M-25 grade (design mix) using 20mm graded aggregates as in foundations, including rafts, footings, foundation beams, plinth beams, bases for columns, etc, basement slabs, under reamed piles and mass concrete complete all as specified and directed.

M & L for formwork to sides of concrete foundations, footings, bases of columns, raft and beams, sides and soffits (if any) of foundation and plinth beams , and similar work, vertical or to batter, flat surfaces of concrete , surface is required to be fair finished complete all as specified and as directed by the Engineer-in-Charge

M & L for M-25 grade (design mix) using 20mm graded aggregates as in columns, pillars, piers, posts and struts complete all as specified and as directed by the Engineer-in-Charge.

M & L for formwork to sides of pillars, posts, struts, piers, columns and stanchions, rectangular or polygonal surfaces of concrete , surface is required to be fair finished. complete all as specified and as directed by the Engineer-in-Charge

M & L for RCC M-25 (design mix) using 20mm graded aggregates as in Roof beams, lintel beams/bands, cantilevers, shelves,bressummers, lintels over 1.5m span, chajjas etc complete all as specified and as directed by the Engineer-in-Charge.

M & L for formwork to sides and soffits of floor or roof beams, soffits of lintel beams/ bands, chajjas, beam haunchings, girders, bressum-mers, lintels, cantilevers, shelves including supports overhangs etc, also splays between floors and beams, etc., flat surfaces of concrete , surface is required to be fair finished. complete all as specified and as directed by the Engineer-in-Charge

M & L for RCC M-25 (design mix) using 20mm graded aggregates as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed by the Engineer-in-Charge.

M & L for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping), flat surfaces of concrete , surface is required to be fair finished. complete all as specified and as directed by the Engineer-in-Charge

M&L for 15 mm thick rendering on brick surfaces in CM 1:4 finished even and smooth without using extra cement complete all as specified and directed

M&L for 10mm thick redering on brick work surfaces in CM 1:6 finished even and smooth without using extra cement complete all as specified and directed

M&L for rendering in cement mortar (1:4) 10mm thick as in ceiling surfaces finished even and smooth without using extra cement, complete all as specified & directed.

M&L for preparation of new plaster surfaces and applying three coats of lime/ white wash on ceiling surfaces, complete all as specified and directed.

M&L for preparation of new plastered surfaces of walls and applying two coats of oil emulsion distemper (OBD) of approved shade/tint over a coat of primer over & including a finished coat of white wall care putty, complete, all as specified & as directed.

M&L for preparation of newly plastered surfaces of wall and applying two coats of weather proof water base emulsion paint with modified acrylic exterior wall finished with silicon adhesive of approved shade/tint over a coat of primer over & including a finished coat of white wall care putty, complete, all as specified & as directed.

S & F aluminium door shutters with frame of aluminium section including necessary joining cleats, glazing clips, rubber neoprene packing, brass handle and brass tower bolts of size 150mm x 02 Nos in each door, hinges, anodised aluminium snap beading screws, hydraulically regulated double action floor door spring made up of 1.25mm thick aluminium alloy sheet foundation box for each shutter, etc and incl fitted with 5mm thick tinned glass in glazed shutter with brass mortice lock 100mm 2 levers, vertical type complete all as specified and directed

S & F aluminium window/ventilator shutter with frame, sliding/side hung type with sash bars including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc and incl each window fitted with 5 mm thick tinned glass in glazed shutter, duco pattern aluminium anodised grill (weight not less than 2.625 Kg/Sqm) and stainless wire cloth 0.36mm nominal dia and average width of aperture 1.40mm in gauzed shutter etc complete all complete all as specified and directed

Supply only integral water proofing compound, ISI m,arked complete all as specified and directed

M&L for screeding 10mm thick in CM 1:4 on fair faces of RCC /stone patti roof surface finished fair & even complete all as spescified and directed.

M & L for five layered roof treatment with APP modified polymeric water proofing membrane, 2mm thick having centre core not less than 100 micron high molecular high density polythylene film (HMHDPE) protected on both sides with high polymeric asphaltic mix and 20 micron HMHDPE film weight not less than 3 Kg/ Sqm applied with bonding material using belown type bitumen conforming to IS-702 Grade 85/25 @ 1.20 Kg/ Sqm over bitumen primer conforming to IS- 3384 @ 0.40 Kg/ Sqm with final coat of bonding bitumen grade 85/25 @ 1.20 Kg/ Sqm over APP membrane with all overlaps complete all as specified and directed.

M&L for 40mm thick (average consolidated thickness) PCC (1:2:4) type B-0 using 12.5 mm graded stone aggregate laid in slope as in padding, finished even and smooth on existing slope including provision of 'V' shaped groove 6mm wide and 10mm deep at 1.20 metre interval or parts thereof, both ways on top of PCC padding and filled with mastic bitumen of (1:1) proportion complete all as specified and directed.

M&L for 18/19mm thick block board grade-.II quality, interior grade with decorative type with decorative face veneer on one face fixed complete, including teak wood lipping 19 x 6mm thick fixed with nails in shelves, partition and palmet boxes, shelves, almirah book cases, toilet boxes, racks, cup board shutter and similar works all as spepcified and directed.

S & F continuous (piano) hinges, mild steel, bright finish width of flaps (when open ) 40 mm all as specified and directed.

S & F 50 mm dia polished hardwood knobs fixed with screws complete all as specified and directed.

M&L for point wiring with 1.5 Sqmm, PVC insulated, unsheathed, stranded copper conductor single core FRLS cable, IS-694 marked, drawn through and including non metallic rigid PVC concealed conduit 20mm dia or higher complete with all PVC conduit accessories such as socket, elbow, junction box, bell mouth, reducer, bend and flexible conduit etc./ fittings ISI marked and sunk type pressed steel anodised terminal box 1.2 mm thick with bakelite laminated sheet top cover 3 mm thick, brass screws and cup washers including 1.5 Sqmm stranded copper conductor PVC insulated green in colour as continous earth conductor connected to common earth and earth dolly with all accessories for one light/ exhaust fan point controlled by one, one way switch complete all as specified and directed

S&F switch piano flush type 5 amps, single pole one way 240 volts.

S&F ceiling rose surface bakelite 3 terminals 63.5 x 17 mm.

S&F LED tube light fitting in acrylic linear tube (1x 18 watt),230V for single LED tube light including 1 x 18 W LED retrofit bar professional CW 6500 K cover channel, bipin holders,LED power driver, connector block, etc complete with all accessories internally prewired and including connecting up with three core flexible copper conductor cable with suitable size for connection of fitting from ceiling rose complete all as specified and directed. Make Havells Cat part No PHOTONULTRA2.01212T8SSTL20WLED 865SPC (for tube) REGALBATTENT8UPTO1X22WDSBSWH (for batten)/ Bajaj Cat Part No BLRB 18W CWc for tube & BLRB - DB 118 for batten or equivalent model from Philips/Crompton

Supply and fixing testing and commissioning energy saving street light luminaire 35 watt LED , pressure die cast housing with epoxy powder coated with colour finish and prismatic poly carbonate coverlic cover complete, IP 66 protection incl connecting with three core copper flexible wire from ceiling rose to connector of light fitting complete all as specified and directed by Engr-in-Charge. Make- Havells Cat Part No ENDURACITYLITEPLAT PLUSSL35WLED757SASYBOPC or equivalent model from Surya/Control& Switchgear/Bajaj

Supply and fixing street light bracket made of 32 mm GI pipe , 1.2 mtr lenght fixed with two nos of clamp , nut and bolts for fixing of street light complete all as specified and directed by Engr-in-Charge.

S&F of MCB distribution board single pole & neutral with 200 Amps rated bus bar, double door IP-43 DB's , made out of sheet steel enclosure, recessed type, factory made powder coated 8 way, 240 volts suitable for housing MCB's including blanking plate complete all as specified and directed.

S & F of MCB SPN, 240 volt, 32 Amp capacity, 10 KA, 'C' curve complete all as specified and directed.

S & F of MCB SP, 240 volt, 6 Amp to 40 Amp capacity, 10 KA, 'C' curve complete all as specified and directed.

M&L for earthing complete with galvanised steel earth plate electrode 60cmx60cmx6 mm thick buried directly in ground vertically to a depth not less than 2.25m below ground level with top edge of the earth plate at a depth not less than 1.5m below ground level, connected to galvanised earth lead wire 4.00 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel and other end of earth wire connected to main switch board and protected by galvanised iron pipe light grade 15mm bore and water pipe 20 mm bore GI med grade with funnel and wire mesh PCC chamber in cement concrete 1:3:6 type C-2 and RCC cover with handle all as specified and shown in elect plate No 3 of SSR Part-I of 2009.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 10 sq mm 2 core.

Supply and laying tubes light grade GI tubing 40 mm dia with all fitting laid in trenches, fixed on pole/on wall for cable protection complete all as specified and directed

Supply & spreading in trenches dry river sand cushioning to underground cable in trenches including spreading, levelling hand punning down complete all as specified and directed. Note:- Depth of sand cushioning will be measured after punning down and levelling the sand properly.

SHREE BALAJI TRADING CORPORATION

M/S SHIVA TRADERS

ANAM BUILDCON

kirtiman traders