REPAIR, REPLACEMENT OF POLYCARBONATE SHEET GALVALUME ROOF SHEET AND RECONDITIONING OF SCREW HOLES AND SHEET JOINTS IN FACTORY HANGARS OF SED, KORAPUT.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 150 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation. The sheet shall be fixed using self drilling /self tapping screws with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required at all hangars of SED upto a height of 12.00 mtr with all safty precautions etc all complete as per direction of engineer-in-charge as per Approved make.

Providing and fixing precoated galvanised steel plain ridges sheet roofing (500-600mm) of 0.50 mm (+0.05 %) total coated thickness, Zinc coating 150 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws etc all complete as per direction of engineer-in-charge as per Approved make.

Providing and fixing precoated galvanised steel crimp curve sheet of 0.50 mm (+0.05 %) total coated thickness, Zinc coating 150 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws etc all complete as per direction of engineer-in-charge as per Approved make.

Providing and applying weather proof outer silicon sealant at the joints between the sheet,screw holes and at the overlapping of the sheets to prevent roof leakage with aluminium butyl rubber tape pipe applicable for roof water leakage metal surface confirming to IS etc all complete as per direction of engineer-in-charge as per Approved make.

Labour charges for dismantling/removal of sheets including ridges, hips, valleys and gutters etc., laying the sheets from roof and depositing them to salvage yard / Departmental store within SU-30 Factory etc. all complete as per direction of Engineer In Charge.

Sub Total Works Amount

I / We hereby quote percentage above (+) or below (-) the Estimated cost

Sub Total Works Amount

ADD GST @ 18% (( IGST18%) or (CGST @ 9% +SGST@ 9%)), Whichever is applicable

GRAND TOTAL

Note : (i) : It is a percentage rate tender. Hence the tenderers are required to quote rates on percentage basis i.e. above or below the estimated cost put to tender. (ii) The quoted rates in the bill of quantities are inclusive of all types of taxes, duties levies, fees and charges etc., imposed by Central/ State Govt. and local bodies Compensation Cess, Labour Cess, Custom Duty, royalties and other levies. It shall also include all other costs including loading, un-loading, insurance, transportation, testing and Certification expenses except GST . GST at the prevailing percentage is added in the BOQ at the end.

GOODS AND SERVICE TAX (GST)

Bidder should indicate GSTIN No. (Copy of GST registration to be enclosed) and PAN No. (copy of PAN to be enclosed).

Tender will be considered/ accepted, if & only if the vendor has a valid GST Registration No

Central Tax/ State Tax/ Integrated Tax/ Union Territory tax to be quoted as per GST Law

Bidders to ensure correct applicability of Central Tax/ State Tax/ Integrated Tax/ Union Territory tax based on the Inter / Intra state movement Supply of goods and provision services or both

Bidder shall mention the SAC Code/HSN Code for goods and services in accordance with GST law in their Bid and subsequently in their tax invoice. HAL, Koraput Division shall not be responsible for any error in SAC Code/HSN Code for goods and/or services specified by supplier/contractor

The Tax Invoice for supply of Goods & Services should be raised as per the provision of GST Act & Rules and must compulsorily mention the following-

a. HAL, Koraput Division GST registration number as 21AAACH3641R1ZJ

b. Name & address of supplier / Vendor/ Contractors

c. GSTIN of Supplier / vendors / Contractors

d. Consecutive Serial Number & date of issue

e. Description of goods or services

f. Total value of supply

g. Taxable value of supply

h. Tax Rate – Central Tax & State Tax or Integrated Tax, Cess

i. Amount of Tax charged

j. Place of supply

k. Address of delivery if different from place of supply

l. Signature of authorized signatory

Reimbursement of GST to the vendor is contingent upon complying with the following condition by the service provider

i. Uploading the (invoices raised on HAL, KoraputDivision ) onward GST Return (GSTR-1) in GSTN Network portal within the statutory time period

ii. Discharging the GST tax liability to the Government.

iii. Submission of Tax Invoice to HAL, Koraput Division.

iv. Submission of proof of payment of GST to HAL, Koraput Division.

v. Receipt of goods / services by HAL Koraput Division.

vi. Availment of Input Tax Credit by HAL, Koraput Division .

In case GST credit is delayed/ denied to HAL, Koraput Division, due to non/delayed receipt of goods and/or services and/or tax invoice or expiry of timeline prescribed in GST Law for availing such ITC, or any other reason not attributable to HAL, Koraput Division, GST amount shall be recoverable from Vendor along with interest & penalty levied/ leviable on HAL, Koraput Division, as the case may be

In case vendor delays declaring such invoice in his return and GST credit availed by HAL, Koraput Division is denied or reversed subsequently as per GST law, GST amount paid by HAL, Koraput Division towards such ITC reversal as per GST law shall be recoverable from vendor/contractor along with interest & penalty levied/ leviable on HAL, Koraput Division.

In case of discrepancy in the data uploaded by supplier in the GSTN portal or in case of any incomplete work/service, then HAL, Koraput Division will not be able to avail the tax credit and will notify the supplier of the same. Supplier has to rectify the data discrepancy in the GSTN portal or issue credit note (details to be uploaded in GSTN portal).

For any such delay in availing of tax credit for reasons attributable to vendor (as mentioned above), interest as per the GST Act & Rules, along with penalty, if any will be deducted for the delayed period i.e. from the month of receipt till the month tax credit is availed, from the running bills.

Penalty amount so determined along with GST if applicable thereon shall be recovered from the contractor.

Any reduction in rate of Tax on any supply of goods or services or the benefit of input tax credit shall be passed on to the recipient by way of commensurate reduction in prices. Bidders have to submit declaration in their bid that they have complied with ‘Anti-profiteering clause’ under GST law.

The bidder’s quoted rates/ price should be after considering the Input Credit under GST law at their end, since GST on output (GST amount charged in Invoice) will be paid by HAL.

In case any changes in taxes and duties as per Gov. Notification (including GST), the same shall be applicable from time to time.

Quarters will be allotted to the awarded agency subject to availability & recommendation from the E-I-C/ O-I-C for which rents as applicable will be recovered from the running bills of the agency.