PROVISION OF SOLID WASTE MANAGEMENT PLANT AT BIKANER AND SURATGARH MIL STATION UNDER EPC MODE

Design, procurement, construction, commissioning, solid waste management facility for recycling of dry, wet and other waste for daily guaranteed Acceptable Waste of Bikaner station as given in waste generation details of Bikaner at 90% probability confidence level and probable future expansion of 25% for 10 years of the contract period (for a population as given in waste generation details of Bikaner) with fully automated dirty materials recovery facility (MRF) with AI enabled and PLC controlled screening, shorting, separation of recyclable/ non recyclables/ RDF/ Inert from the solid waste and monitoring through SCADA complying the Solid Waste Management Rules, 2016 including creating assets, operation, maintenance and service for 10 years and shall comprise as under: - (a) Preparation and finalisation of Detail Project report (b) The space for stacking of solid waste of minimum 2 days. (c) Disposal of the remaining materials after recycling (if any) at given area within the A-1 land without any extra cost to the Department. (d) Design, prepare architectural/ structural drawing, fabrication, supply, transportation, erection of pre-engineered shed/sheds. (e) Design, prepare architectural/ structural drawing, supply, transportation, construction, installation of Weigh Bridge. (f) Design, prepare architectural/ structural drawing, supply, transportation, construction of observer room, Guard House, Wash room (both male and female), change room (both male and female), rest room, various storage, processing are, dispatch area, etc. (g) Design, fabrication, supply, transportation, installation of Solid Waste Management Plant including feeding hooper, conveyor belts, trammel screening machine, magnetic separator, shredder machine, balling machine, organic waste composer, air blower, solid waste incinerator. (h) Design, supply, transportation, installation, commission and testing of Diesel Engine Generator Set. The fuel shall be supplied by the contractor during the operation, maintenance and service period.

Srl Item No 1.001 Continued...... (i) Design, prepare architectural/ structural drawing, supply, transportation, construction of garages, compound wall of height 2.4 metre, barbed wire fencing of height 0.6 metre above the compound wall, gates, roads, area drainage, sewage disposal, internal electrification, inter water supply, firefighting arrangement, area lighting. (j) Obtain statutory clearance from Government. (k) Maintain, operate, including repairing, replacing, etc. plants and the infrastructure created for 10 years after creating the assets. The contractor shall have full ownership of the materials recycled/extracted from solid waste. No royalty shall be charged by the Government. (l) The contractor shall bear the cost of electricity at prevailing rates however the electricity shall be supplied by the department (m) The rates quoted are inclusive of comprehensive maintenance and the payment schedule shall be as under: - (i) After Finalisation of detail project report- Nil (ii) After Creating assets - 70% of the quoted amount (As per the Yard stick approved by CWE for intermediate period) (iii) After completion of 1 year of comprehensive maintenance: 72% (iv) After completion of 2 year of comprehensive maintenance: 74% (v) After completion of 3 year of comprehensive maintenance: 76% (vi) After completion of 4 year of comprehensive maintenance: 79% (vii) After completion of 5 year of comprehensive maintenance: 82% (viii) After completion of 6 year of comprehensive maintenance: 85% (ix) After completion of 7 year of comprehensive maintenance: 88% (x) After completion of 8 year of comprehensive maintenance: 92% (xi) After completion of 9 year of comprehensive maintenance: 96% (xii) After completion of 10 year of comprehensive maintenance: 100%

Srl Item No 1.00 Continued...... The retention money shall be as applicable.

Design, procurement, construction, commissioning, solid waste management facility for recycling of dry, wet and other waste for daily guaranteed Acceptable Waste of Suratgarh station as given in waste generation details of Bikaner at 90% probability confidence level and probable future expansion of 25% for 10 years of the contract period (for a population as given in waste generation details of Suratgarh) with fully automated dirty materials recovery facility (MRF) with AI enabled and PLC controlled screening, shorting, separation of recyclable/ non recyclables/ RDF/ Inert from the solid waste and monitoring through SCADA complying the Solid Waste Management Rules, 2016 including creating assets, operation, maintenance and service for 10 years and shall comprise as under: - (a) Preparation and finalisation of Detail Project report (b) The space for stacking of solid waste of minimum 2 days. (c) Disposal of the remaining materials after recycling (if any) at given area within the A-1 land without any extra cost to the Department. (d) Design, prepare architectural/ structural drawing, fabrication, supply, transportation, erection of pre-engineered shed/sheds. (e) Design, prepare architectural/ structural drawing, supply, transportation, construction, installation of Weigh Bridge. (f) Design, prepare architectural/ structural drawing, supply, transportation, construction of observer room, Guard House, Wash room (both male and female), change room (both male and female), rest room, various storage, processing are, dispatch area, etc. (g) Design, fabrication, supply, transportation, installation of Solid Waste Management Plant including feeding hooper, conveyor belts, trammel screening machine, magnetic separator, shredder machine, balling machine, organic waste composer, air blower, solid waste incinerator. (h) Design, supply, transportation, installation, commission and testing of Diesel Engine Generator Set. The fuel shall be supplied by the contractor during the operation, maintenance and service period.

Srl Item No 2.00 Continued...... (i) Design, prepare architectural/ structural drawing, supply, transportation, construction of garages, compound wall of height 2.4 metre, barbed wire fencing of height 0.6 metre above the compound wall, gates, roads, area drainage, sewage disposal, internal electrification, inter water supply, firefighting arrangement, area lighting. (j) Obtain statutory clearance from Government. (k) Maintain, operate, including repairing, replacing, etc. plants and the infrastructure created for 10 years after creating the assets. The contractor shall have full ownership of the materials recycled/extracted from solid waste. No royalty shall be charged by the Government. (l) The contractor shall bear the cost of electricity at prevailing rates however the electricity shall be supplied by the department (m) The rates quoted are inclusive of comprehensive maintenance and the payment schedule shall be as under: - (i) After Finalisation of detail project report- Nil (ii) After Creating assets - 70% of the quoted amount (As per the Yard stick approved by CWE for intermediate period) (iii) After completion of 1 year of comprehensive maintenance: 72% (iv) After completion of 2 year of comprehensive maintenance: 74% (v) After completion of 3 year of comprehensive maintenance: 76% (vi) After completion of 4 year of comprehensive maintenance: 79% (vii) After completion of 5 year of comprehensive maintenance: 82% (viii) After completion of 6 year of comprehensive maintenance: 85% (ix) After completion of 7 year of comprehensive maintenance: 88% (x) After completion of 8 year of comprehensive maintenance: 92% (xi) After completion of 9 year of comprehensive maintenance: 96% (xii) After completion of 10 year of comprehensive maintenance: 100%

Srl Item No 2.00 Continued...... The retention money shall be as applicable.

Lump sum price worked out by the tenderer for “EXTERNAL ELECTRIC SUPPLY WORKS" as listed in Schedule ‘A’ Part-III

Schedule ‘A’ Part -III (EXTERNAL ELECTRIC SUPPLY WORKS)

Supply, laying of Double wall corrigated pipe of outer dia 63 mm and inner dia 50 mm for cable protection complete all as specified and directed by Engineer - In - Charge.

Supply, laying of Double wall corrigated pipe of outer dia 110 mm and inner dia 93 mm for cable protection complete all as specified and directed by Engineer - In - Charge.

M & L for boring of holes under main road pavment,hard standing by trenchless technology using ultra sound tecnique and necessary machine for accomodet upto 40mm bore GI tube (light grade) in the drilled holes,returning ,filling in the end working space including removal of surplus soil and making good the surface. Note : (i) GI pipe light grade shall be measured and paid separately. (ii) Only lengh of the road/had standing/pavement will be measured and necessary excavation at both side of bore will be will be mearured and paid separately under relevent item of the BoQ

Supply & fix LT panel out door (Kiosk type) type, weather & vermin proof MS sheet housing 3.15mm thick, powder coated over a coat of primer, double door, front & rear openable type, mounted on 40x40x6 mm angle iron frame, floor mounted type with one MCCB, 4 pole, 125 Amp, 25 KA 415 volts as (incomer) and 63 Amp 4 pole (outgoing)-03 Nos, 40 Amp 4 pole MCCB -02 (Outgoing) Nos copper bus bar 200 Amp of length not less than 60 cm, 4 pole duly drilled with holes for cable connections, after due approval of panel drawing including PCC pedestals of suitable size, removal of old unsv panel, making good the area complete all as specified and directed by Engr-in-charge.

Supply, installation, commissioning and testing of factory made cubical LT feeder pillar box, out door type IP 65, powder coated suitable for floor mounting made out of 3.15 mm thick CRCA sheet with front hinged opening with rubber lining, having flush locking arrangement complete providing sufficient space for cable entry from sides suitable including copper strip 1x4 Nos , 150 amps rating mounted on bus bar insulators for connecting with MCCB at outgoing to connect mother accessories and consist of following

Incoming

(i)MCCB 63 Amps, rating 415 Volts, 4 pole cap 25 KA with thermal magnetic setting type - 01 No.

(iv)LED indicating lamps RYB-01 Set (Set of three).

Outgoing

(i)Supply and fix 3 Pole MCCB 32 Amp, 50 Hz, 415 V with rupturing capacity 18 KA. 02 Nos

(ii)S&F nature switch for automatic ON/OFF of street light by sensing natural light of 3 phase upto 12KW load. For switching ON< = 30 lux, For switching OFF>=10 Lux, Auto high voltgae sense and trip, auto low voltage sense and trip, 50-60HZ, IP66 protection class 2, with copper wiring by minimum of 10 Sqmm .

S&F polycarbonated unbreakable Junction box with fuse provn and suitable connection for three phase incoming cable, single phase out going cable endorsed in thermo plastic enclosure. Shock proof safe IP 65, weather proof, rust proof, dust and water proof internally embedded gasket with provn for cable entry through glade of size 200x160x98mm along with MS Clamps copper bus bar for three phase connection and 02X MCB SP 6 Amp 10 KA incl single phase 2.5 sqmm copper conductor PVC sheathed as required at site for electric connection to LED lights and connecting wire from JB to LED fitting as required complete all as specified directed.

M&L for Earthing complete with galvanized iron slotted pipe of dia 40mm bore, 3 mtr long (earth pit not less than 10 mtr deep below normal ground level) surrounded by adequate quantity of charcoal, dust and salt to packed thickness of 15 cm on all sides, connected to GI Strip 32X6 mm by means of bolts, nuts check nuts and washers of galvanized iron and steel earth and rivetted/welded to earth plate at one end and other end of strip connected to equipemnent body/ test point with two nos nuts , bolts including 32X6 mm flat iron clamp. nuts bolts and washers and also watering pipe 20mm bore GI pipe medium garde from earth p[it to top electrode including funnel, wire mesh,copper lugs etc complete with earth pit in PCC 1:3:6 type C1 using 20mm graded crushed stone aggregate and 40 mm thick PCC 1:2:4 type B1 cover complete all as shown in electrical plate No 3 of SSR Part-I including necessary excavation and earth work in any type of soil, returning filling and disposal of surplus soil to a distance not exceeding 50 mtr complete all as specified and as directed. Note :- PCC Chamber shall be constructed atleast 1.5 Mtr away from the earthing electrode and pipe for watering shall be provided in stanting manner.

Supply, Erecting & Testing Gl. Octagonal pole 7.0 mtr long top dia 70 mm & bottom dia 130 mm with base plate 220 x 220 x l2 mm, thickness 3.0 mm, including G.l. Foundation Nut & Bolt [420, 600 mm long (4 Nos) & GI. Single arm bracket 1.0 mtr long 40 mm dia. Including earth work complete all as specified and directed by Engineer -In -Charge

Supply and laying double wall corrugated pipe (DWC), non-metallic, Resistance to Compression : Type 450, Resistance to Impact: Normal, Resistance to Bending : Pliable, Resistance to External Influence: Ingress Protection : IP 67, Resistance against Corrosion : Without Protection, Resistance to Flame Propagation : Non Flame Propagating, Nominal outside diameter 90 mm, minimum inside dia 37 mm conforming to IS 16205 (Part 24) : 2017 complete all as specified and as directed.

Supply and installation of 11 KV Compact Sub Station with non extensible RMU consisting of 1 No manually operated 11 KV/630 Amp VCB in SF6 insulated stainless enclosure, HT cable /Bus bar, 1 Nos transformer 160 KVA ,11 KV/433 CRT dry type & associated LT devices complete as directed.

Supply & fix LT panel out door (Kiosk type) type, weather & vermin proof MS sheet housing 3.15mm thick, powder coated over a coat of primer, double door, front & rear openable type, mounted on 40x40x6 mm angle iron frame, floor mounted type with one MCCB, 4 pole, 250 Amp, 36 KA 415 volts as (incomer) and 200 Amp 4 pole (outgoing)-02 Nos, 40 Amp 4 pole MCCB -02 (Outgoing) Nos aluminium bus bar 200 Amp of length not less than 60 cm, 4 pole duly drilled with holes for cable connections, after due approval of panel drawing including PCC pedestals of suitable size, removal of old unsv panel, making good the area complete all as specified and directed by Engr-in-charge.

Supply, installation, commissioning and testing of factory made cubical LT feeder pillar box, out door type IP 65, powder coated suitable for floor mounting made out of 3.15 mm thick CRCA sheet with front hinged opening with rubber lining, having flush locking arrangement complete providing sufficient space for cable entry from sides suitable including copper strip 1x4 Nos , 160 amps rating mounted on bus bar insulators for connecting with MCCB at outgoing to connect mother accessories and consist of following

Incoming

(i)MCCB 250 Amps, rating 415 Volts, 4 pole cap 50 KA with thermal magnetic setting type - 01 No.

(iv)LED indicating lamps RYB-01 Set (Set of three).

Outgoing

(i)Supply and fix 3 Pole MCCB 200 Amp, 50 Hz, 415 V with rupturing capacity 50 KA. 01 Nos

Lump sum price worked out by the tenderer for “EXTERNAL WATER SUPPLY WORKS" as listed in Schedule ‘A’ Part -II

Schedule ‘A’ Part -II(EXTERNAL WATER SUPPLY WORKS)

Supply and fixing Gun metal gate valve with locking device and open shut indicator for 25 mm bore iron pipe , with iron wheel head, screwed both ends conforming to IS 778 - 1984 complete all as specified and directed.

Supply and fixing Gun metal gate valve with locking device and open shut indicator for 20 mm bore iron pipe , with iron wheel head, screwed both ends conforming to IS 778 - 1984 complete all as specified and directed.

Boring of holes under road, pavement, hard standing by trenchless technology using ultra sound technique and necessary machine or by using manual mechnical tools with manpower including passing suitable for GI pipe medium Grade.

Supply and lay Centrifugally cast (Spun) Ductile Iron pressure pipe with spigot & socket end, class K-7 conforming to IS:8329/2000 suitable for (push on) rubber gasket jointing with centrifugally applied inside cement mortar lining and external zinc coating with a finishing layer of black bitumen coating on external surfaces, size 100 mm (4”) dia including jointing material i.e. ethylene propylene diene monomer (EPDM) rubber gasket conforiming to IS: 5382 of bulb type complete as specified and directed by Engr-in-charge.

Cutting existing water pipe line bore 200 mm and inserting of flanged Tee 200x200x100 mm , flanged socket, rubber gasket, nut bolt etc. and making leak proof joint complete for new water pipe connections Note:- DI fittings special fittings shall be measured and paid seperately.

DI fittings, class K-12, confirming to IS-9523-2000 suitable for spigot & socketed pipes such as bends (any type, radius and angle), tapers any type (straight, bend, increasing, decreasing or double socket etc), tee pieces, single branch, 'Y' junction, double branch, cross collar, caps and plugs etc. suitable for spigot and socketed pipes upto 200 mm bore complete all as specified and directed by Engineer-in-charge.

Lump sum price worked out by the tenderer for “EARTH WORKS" as listed in Schedule ‘A’ Part- IV

Lump sum price worked out by the tenderer for “Demolition" as listed in Schedule ‘A’ Part- V

Lump sum price worked out by the tenderer for Road, path & culvert works as listed in Schedule ‘A’ Part- VII

Please Enable Macros to View BoQ information