WELCOME MAINTENANCE AND CERTAIN B/R WORKS TO SMQ AT SECTOR 31 A AND 31 D AT CHANDIGARH UNDER GE (AF) CHANDIGARH

Amount

Note :The unit rate quoted by the tenderer under Col No (13) of Sch `A’ (BOQ) unless specifically mentioned otherwise such as labour only/fixing only, for all items of works shall be deemed to be including cost of all materials, labour, tools and plants, testing and commissioning of work in position complete as required for entire completion of work.

Plain cement concrete ,25 mm average thickness (1:2:4) type B-0, using 12.5 mm graded mechanically crushed stone aggregates as in level course/ sub base finished even & rough to receive the bedding mortar in and including demolition of unreinforced cement concrete in ground floors and paving n.exc 15cm thickness (below or above ground level) and removal of rubbish outside MoD land , complete all as specified and directed by Engineer-in-Charge.

Plain cement concrete 75 mm thick, 1:3:6, type C-2, using 40 mm graded mechanically crushed stone aggregates, laid in 1:20 slope as in plinth protection/court yard including making joints at 3.00 metre intervals and at each corner, the joint shall be filled with mastic filling (to full depth) comprising of one part heated hot blown bitumen 85/ 25 & two parts heated sand (by volume), surface finished even and fair in and including demolition of unreinforced cement concrete in ground floors and paving n.exc 15cm thickness (below or above ground level) and removal of rubbish outside MoD land , complete all as specified and directed by Engineer-in-Charge. Note :Quoted rates are inclusive of use and waste of formwork and to devide the area in panels.

Brick work with sub-class `B' bricks Fly ash bricks (bricks shall be burnt clay fly ash building bricks as per IS- 13757), straight or curved on plan exceeding 6 M mean radius built in cement sand mortar 1:4 complete in and including demolition of brickwork or stone boulder masonary built in cement mortar including all quoins, arches, pillars etc for the area where unservicable bricks retrived and removal of rubbish outside MoD land , complete all as specified and directed by Engineer-in-Charge. Notes: (i) Servicable bricks retrived from demolition of this item shall be used after proper cleaning and washing of old bricks under item No.04 below. (ii) Tile work to be executed in any position or in any patches or as per site requirement.

Brick work with sub-class `B' bricks, straight or curved on plan exceeding 6 M mean radius (except bricks) built in cement sand mortar 1:4 complete in and including demolition of brickwork or stone boulder masonary built in cement mortar including all quoins, arches, pillars etc for area where servicable bricks retrived and removal of rubbish outside MoD land ,complete all as specified and as directed by Engineer -in-Charge. Notes: (i) Servicable bricks retrived from demolition of item No.03 and this item shall be used under this item after proper cleaning and washing of old bricks. (ii) Tile work to be executed in any position or in any patches or as per site requirement.

First quality glazed ( digital glossy finish) ceramic coloured tiles of 350x450x 7 to 8 mm thick fixed joint free laid on vertical surfaces such as skirting, dados and risers to steps etc laid over and including 10mm thick cement plaster in CM (1:4) set and jointed in neat cement paste of honey like consistancy and pointed in white or coloured cement to match the shade of tiles in and including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and removal of rubbish outside MoD land ,complete all as specified and as directed by Engineer -in-Charge. Notes :- (i) Design, pattern and colour of tiles will be as approved by GE. (ii) Tile work to be executed in any position or in any patches or as per site requirement.

First quality, Non skid ceramic coloured tiles, 7 to 8 mm thick joint free (square/ rectangular) area of each tile exceeding 0.11 Sq.m but not exceeding 0.18 Sq.m, laid in floors with neat cement slurry @ 3.00 kg/Square Metre over and including 15 mm thick screed bed of cement mortar (1:4) including pointing in white or coloured cement to match the shade of tiles in and including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and removal of rubbish outside MoD land ,complete all as specified and as directed by Engineer -in-Charge. Notes :- (i) Design, pattern and colour of tiles will be as approved by GE. (ii) Tile work to be executed in any position or in any patches or as per site requirement.

Vitrified ceramic tiles (light Shade) 9 to 10 mm thick (square/ractangular) coloured polished tiles, area of each tile not exceeding 0.36 sqm in floors etc. laid in floors with neat cement slurry @ 3.00 kg/Square Metre over and including 15 mm thick screed bed of cement mortar (1:6) including pointing in white or coloured cement with pigment to match the shade of tiles in and including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and removal of rubbish outside MoD land ,complete all as specified and as directed by Engineer -in-Charge.

Vitrified ceramic tiles (light Shade) 9 to 10mm thick (square/ractangular) coloured polished tiles, area of each tile not exceeding 0.36 sqm as in skirting, dados and risers to steps etc laid over and including 10mm thick cement plaster in CM (1:4) set and jointed in neat cement paste of honey like consistancy and pointed in white or coloured cement with pigment to match the shade of tiles in and including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and removing rubbish off the premises, complete all as specified and directed by the Engineer in Charge.

Machine cut Kota stone slab of 18-20 mm thick as in risers of steps skirting, dado and pillar etc laid over 10mm thick cement plaster in CM (1:4) and jointed with grey cement slurry, mixed with pigment to match the shade of the slab including rubbing and polishing in and including demolition of stone slab and tiles of any description or thickness in floors, aprons etc, laid bedded and pointed in cement mortar and removal of rubbish outside MoD land ,complete all as specified and as directed by Engineer -in-Charge. Notes :(i) Rate of kota stone flooring includes for all cutting and waste including machine cutting to make it square or rectangular. (ii) The quoted rate is inclusive for polishing by machine. (iii) Kota stone to be fixed in staircase Riser shall be of single piece.

Machine cut Kota stone slab of 18-20 mm thick as in landing etc laid over 15mm thick cement plaster in CM (1:6) and jointed with grey cement slurry, mixed with pigment to match the shade of the slab including rubbing and polishing in and including demolition of stone slab and tiles of any description or thickness in floors, aprons etc, laid bedded and pointed in cement mortar and removal of rubbish outside MoD land ,complete all as specified and as directed by Engineer -in-Charge. Notes :(i) Rate of kota stone flooring includes for all cutting and waste including machine cutting to make it square or rectangular. (ii) The quoted rate is inclusive for polishing by machine.

Granite (of any type ) 16-18 mm thick, work (table rubbed and polished) fine grained 'Z' black/red in cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over and including screed bed of 15 mm thick in CM 1:3 in and including demolition of stone slab and tiles of any description or thickness in floors, aprons etc, laid bedded and pointed in white cement with pigment and removal of rubbish outside MoD land ,complete all as specified and as directed by Engineer -in-Charge.

Coloured chequered cement concrete tiles 300mm x 300mm x 25mm thick/400mm x 400mm x 25mm thick, factory made, ISI marked (IS 13801-1993), with grey cement & pigment, laid with neat cement slurry @ 3Kg/Sqm over & including 20mm thick screed bed of cement mortar (1:6), pointed in white cement with matching colour pigment in and including demolition of stone slab and tiles of any description or thickness in floors, aprons etc, laid bedded and pointed in white cement with pigment,complete all as specified and directed by Engineer-in- Charge.

Heavy duty vitrified ceramic designer ultra tiles 300mm x 300mm x 15mm thick, factory made, ISI marked (IS 15622-2017), with grey cement & pigment, laid with neat cement slurry @ 3Kg/Sqm over & including 15mm thick screed bed of cement mortar (1:6), pointed in white cement with matching colour pigment in and including demolition of stone slab and tiles of any description or thickness in floors, aprons etc, laid bedded and pointed in white cement with pigment,complete all as specified and directed by Engineer-in- Charge.

Rendering 15 mm thick plaster on brick work or concrete surfaces in cement mortar (1:4) finished even and smooth without using extra cement, complete all as specified and directed by Engineer-in-Charge.

Rendering 15 mm thick plaster on brick work or concrete surfaces in cement mortar (1:6) , finished even and smooth without using extra cement, complete all as specified and directed by Engineer-in-Charge.

Rendering 15 mm thick on brick work or concrete surfaces in cement mortar 1:4 finished even and smooth without using extra cement in and including taking down cement plaster on brick walls & concrete surfaces & the like including raking out joints, hacking for key, scrubbing down with water etc., any description, and removal of rubbish outside MoD land , complete all as specified and directed by Engineer-in-Charge.

Rendering 15 mm thick on brick work or concrete surfaces in cement mortar 1:6 finished even and smooth without using extra cement in and including taking down cement plaster on brick walls & concrete surfaces & the like including raking out joints, hacking for key, scrubbing down with water etc., any description, and removal of rubbish outside MoD land , complete all as specified and directed by Engineer-in-Charge.

Rendering 10 mm thick in cement mortar (1:3), as on concrete surfaces (such as top & bottom of chajjas, roof projection ,balcony ,mummty and stair case flight ceiling ,roof slab ceiling etc.) finished the surfcae even and smooth without using extra cement in and including taking down cement plaster on brick walls & concrete surfaces & the like including raking out joints, hacking for key, scrubbing down with water etc., any description, and removing of rubbish outside MoD land , complete all as specified and directed by Engineer-in-Charge. Notes for item No. 16, 17 &18: (i).Quoted rate shall be deemed to include for necessary scaffolding & formwork for building upto 12.00m high (Ground+2 storey building). (ii) No extra payment made to contractor for work in small patches as required at site/as directed. (iii) All safety measures for the safety of workers shall be ensured by contractor before execution of work. Insurance of workers shall be got done by contractor before execution of the work and the cost for the same shall be deemed to be included in rate quoted by contractor.

Preparation of new plastered or unplastered surfaces of ceiling and applying three coats of white washing , complete all as specified and directed by Engineer-in-Charge.

Preperation of newly plastered surfaces of walls and applying two coats of cement base paint over 1mm thick wall care putty to smoothening the surface by using sand paper , complete all as specified and directed by Engineer-in-Charge.

Preparation of new plastered or unplastered surfaces of walls and applying two coats of oil bound distemper over 1mm thick wall care putty grade to smoothening the surface by using sand paper , complete all as specified and directed by Engineer-in-Charge.

Preparation of old surfaces of walls including brooming down or steel wire brushing, scraping down smoke soot, moulds, mooss and efflorescent salts and trading oil and greasy spots etc and filling the cracks/holes with cement wall care putty and applying one coat of white wash , complete all as specified and directed by Engineer-in-Charge.

Preparation of old surfaces of ceiling including brooming down or steel wire brushing, scraping down smoke soot, moulds, mooss and efflorescent salts and trading oil and greasy spots etc and filling the cracks/holes with cement wall care putty and applying one coat of white wash, complete all as specified and directed by Engineer-in-Charge.

Preperation of old surfaces of walls including brooming down or steel wire brushing scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots etc; etc and filling the cracks/holes with cement wall care putty and applying one coat of oil bound distemper , complete all as specified and directed by Engineer-in-Charge.

Preperation of old surfaces of ceiling including brooming down or steel wire brushing scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots etc; etc and filling the cracks/holes with cement wall care putty and applying one coat of oil bound distemper , complete all as specified and directed by Engineer-in-Charge.

Complete removal of existing treatment of internal surfaces of walls including brooming down or steel wire brushing scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots etc; washing, rubbing down and stopping of surfaces using sand paper and applying two coat of oil bound distemper including 1mm thick Walll care putty and smoothing the surface, complete all as specified and directed by Engineer-in-Charge.

Complete removal of existing treatment of plastered surfaces of ceiling including brooming down or steel wire brushing scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots etc; washing, rubbing down and stopping of surfaces using sand paper etc and filling the cracks/holes with cement wall care putty and applying two coats of oil bound distemper , complete all as specified and directed by Engineer-in-Charge.

Preparation of old painted wooden surfaces over 10cm width or grith not otherwise described and applying two coats synthetic enamel paint, complete all as specified and directed by Engineer-in-Charge

Preparation of old painted steel or Iron surfaces over 10cm width or grith not otherwise described and applying one coat synthetic enamel paint, complete all as specified and directed by Engineer-in-Charge. Note For Ser Item No. 22 to 29 :- The rates quoted against those items shall be included for the use of scafolding, ladders, cradles etc, up to triple storey building, removing nails, making good holes, cracks etc removing furnitures, cub boards, washing floors, floor and wall tiles,cleaning glasses, joinerys, electric fittings, wiring, conduits etc of drops, splashes and living premises clean and tidy upto entire satisfaction of Engineer-in-Charge,

Taking down Chowkhats with shutters without taking of shutter from the frame of any description not exceeding 1.50 Sq. m each, and making good the disturbed surface in CM 1:4 & finished with similar specification as exists, complete all as specified and as directed by the Engineer-in-Charge.

Taking down Chowkhats with shutters without taking of shutter from the frame of any description exceeding 1.50 Sq. m but not exceeding 4.00 Sq. m each, and making good the disturbed surface in CM 1:4 & finished with similar specification as exists, complete all as specified and as directed by the Engineer-in-Charge.

Taking down shutters of any description exceeding 1.00 Sq. m but not exceeding 2.00 Sq. m each and making good the disturbed surface in CM 1:4 & finished with similar specification as exists, complete all as specified and as directed by the Engineer-in-Charge.

Repairing of wooden/steel shutters after easing and adjusting, replacing of builders hardware and screws including welding/cutting/chesing as required of any description n.exc 1 sq. m each and refixing in the same opening ,complete all as specified and directed by Engineer-in-Charge. Note:- work to be executed in pieces or petty repairs as per site requirements.

Repairing of wooden/steel shutters after easing and adjusting, replacing of builders hardware and screws including welding/cutting/chesing as required of any description exc 1 sq. m and not exc 2 sqm each and refixing in the same opening ,complete all as specified and directed by Engineer-in-Charge. Note:- work to be executed in pieces or petty repairs as per site requirements.

Factory made PVC solid door frame of size 50 mm x 47 mm with wall thickness of 5 mm made out of 5 mm thick plain colour PVC sheet cut at corner and jointed with 02 Nos., 150 mm long brackets of size 15 mm x 15 mm mild steel square tubes 19 gauge including vertical door profiles reinforced with 19 mm x 19 mm steel square tube of 19 gauge (EPDM) rubber gasket weather seal provided throughout the frame and fixed to wall with 65/100 mm long mild steel screws through the frame by using PVC fasteners (minimum of 04 Nos. of screws to be provided for each vertical member & minimum 02 Nos. for horizontal member) ,complete all as specified and directed by the Engineer in Charge.

Factory made solid panel PVC door shutters 30 mm thick (style) consisting of frame made out of MS tube for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for style and plain colour PVC sheets for top rail, lock rail and bottom rail on either sides & as gap insert for top- rail and bottom rails. Paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement supplying and fixing in the frame at site as per specification and drawing ,complete all as specified and directed by Engineer-in- Charge.

Pressed steel frames of size 105 x 60 mm, made out of 1.25mm thick sheet for doors with one or more rebates including necessary fixing lugs, hinges (mild steel butt hinges medium weight, cold rolled, 100 mm, ISI marked), lock strike plate, etc., including one shop coat of primer.with and including back filling PCC (1:3:6), type C-0,complete all as specified and directed by the Engineer in Charge. Note :Cost of filling hollow of frame with plain cement concrete shall be included in the quoted rate and nothing extra shall be admissible on this account .

Pressed steel frames of size 125 x 60 mm, made out of 1.25mm thick sheet for doors with one or more rebates including necessary fixing lugs, hinges (mild steel butt hinges medium weight, cold rolled, 100 mm, ISI marked), lock strike plate, etc., including one shop coat of primer.with and including back filling PCC (1:3:6), type C-0,complete all as specified and directed by the Engineer in Charge. Note :Cost of filling hollow of frame with plain cement concrete shall be included in the quoted rate and nothing extra shall be admissible on this account .

Factory made 35 mm thick (Batten thickness) 2nd class hard wood plain, framed, paneled shutters( two number No of panels) with panels of timber flat on both sides (feather edges) with lock rail and panel of 9 mm thick BWP commercial ply or 12 mm thick veneered particle board with commercial veneering on both faces and size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated and detapering from 5 mm to 10 mm around the panel on one side fitted to chowkat, complete all as specified and directed by the Engineer in Charge.

30 mm thick (Batten thickness) Second class hard wood Glazed and skeleton shutters, open rebated and prepared to receive wire cloth, glass etc. divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars any numbers, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, wire cloth etc., sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats,complete all as specified and directed by the Engineer in Charge.

Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives(maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/ borer proof,water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length in and including dismantling of existing frame, complete all as specified and directed by the Engineer in Charge. Note:M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately.

Factory made double rebated extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/Chowkhat of size 65x125mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives(maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/ borer proof,water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length in and including dismantling of existing frame, complete all as specified and directed by the Engineer in Charge. Note:M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately.

Factory made single extruded WPC (Wood Polymer Composite) solid plain door shutter of size 30 MM thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moistur proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws , complete all as specified and directed by the Engineer in Charge. Note: stainless steel butt hinges and necessary S.S screws shall be paid separately.

Factory made 30 MM thick 100% solid WPC (Wood Ploymer Composite) plain wiremesh door shutter of required size comprising of virgin PVC resin polymer of K value 57-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives made from extrusion procecess WPC foam sheet single exttruded(Inner) with having minimum density not less than 650 kg/cum of density and screw withdrawal strength of 2000 N (Face) & 1100 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moistur proof and fire retardant. For fixing Mosquito mesh and XTN aluminimium mesh combinly panel area of door except stiles and rails to be panelled with mesh with self tapping round headed screws at required distance, scres and edges covered with body threaded PVC edge beading all arround of mesh and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws ,complete all as specified and directed by the Engineer in Charge. Note:M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately.

Factory made single extruded WPC (Wood Polymer Composite) solid plain flush type as in shutter or exposed member of cupboard of 25mm thick with Balancing on one face and wooden grain pattern lamination on exposed surface with and including 18 mm wide 0.8 to 1 mm thick PVC leaping on exposed face to match with shade of shutter fixed with suitable solvent comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant, complete all as specified and directed by the Engineer in Charge. Note:M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately.

Factory made box type steel window with pintle hinges and two nos 150mm mild steel tower bolts to each shutter, steel handle and with glazing bars dovetailed or welded and with one shop coat of zinc chromate primer in and including cutting holes in brick walls for inserting holdfasts and making good dismantled portion in cement mortar 1:4 or cement concrete 1:2:4 Type B-1, complete all as specified and shown on Drawing No CEAF/STD-184-2012 Sheets 1/3 & 3/3 and as directed by the Engineer in Charge.

Factory made made box type steel window with pintle hinges and two Nos 150mm mild steel tower bolts to each shutter, steel handle and without glazing bars, including flat iron 12 x 3 mm for securing wire mesh, dovetailed or welded and with one shop coat of zinc chromate primer complete in and including cutting holes in brick walls for inserting holdfasts and making good dismantled portion in cement mortar 1:4 or cement concrete 1:2:4 Type B-1, complete all as specified and shown on Drawing No CEAF/STD-185-2012 Sheets 1/2 & 2/2 and as directed by the Engineer in Charge.

Factory made box type steel ventilator fixed type, dovetailed or welded and with one shop coat of zinc chromate primer in and including cutting holes in brick walls for inserting holdfasts and making good dismantled portion in cement mortar 1:4 or cement concrete 1:2:4 Type B-1, complete all as specified and shown on Drawing No CEAF/STD-186-2012 Sheets 1/1 and as directed by the Engineer in Charge.

Factory made made box type steel ventilator with glazed shutter or gauzed shutter with glazing bars or flat iron 12 x 3mm dovetailed or welded for fixing wire mesh/glass and with one shop coat of zinc chromate primer in and including cutting holes in brick walls for inserting holdfasts and making good dismantled portion in cement mortar 1:4 or cement concrete 1:2:4 Type B-1, complete all as specified and shown on Drawing No CEAF/STD-186-2012 Sheets 1/1 and as directed by the Engineer in Charge.

Aluminium powder coating (minimum thickness of powder coating 50 micron of approved colour) three track window (two shutters glazed & one shutters wiregauge) with frame, glazed with 4 mm thick tinted glass and, wire gauge with stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm including rubber bead joining cleat for fixing in position, concealed type lock for all three shutter, PVC roller etc all as specified below , including taking down old window , complete all as specified and directed by the Engineer in Charge. Section no are as under : (a) Frame (top & side) section shall be of size 92.00 x 31.75 x 1.50 mm (Section No 20831) (b) Frame (bottom) section shall of size 92.00 x 31.75 x 1.50 mm (Section No 20832) (c) Top & side Members of shutter Section shall be of size 18.00 x 40.00 x 1.55 mm (Section No 20738) (d) Shutter Interlock Section shall be of size 18.00 x 40.00 x 1.45 mm (Section No 20737) (e) Bottom Members of shutter section shall be of size 18.00 x 40.00 x 1.55 mm (Section No 20736) Note: Section numbers mentioned in this item are of Jindal Make, contractor may use similar section of other make mention in Appx B.

Aluminium powder coated (minimum thickness of powder coating 50 micron of approved colour) ventilator, partialy glazed and partialy louvers, outer frame & mullion fabricated with aluminium section of size 82.50mm x 38.00 mm x 1.70 mm thick (Cat No 20036), half portion glazed with 4 mm thick frosted glass including rubber beading, & glazing clip, half portaion louvers of 80 mm wide & 4 mm thick frostade glass including aluminium louver patti including SS wire gauge of fixing of 0.36mm dia and 1.40 width of aparture with 25x3mm think aluminium strip with screw to upper half portion of ventilator all fitting & fixture and fixed in positionincluding taking down old ventilator , complete all as specified and directed by the Engineer in Charge. Note: Section numbers mentioned in this item are of Jindal Make, contractor may use similar section of other make mention in Appx B.

Butt hinges 100 mm size ,extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed type B-21 ISI marked ,complete all as specified and directed by the Engineer in Charge.

Barrel tower bolts aluminum anodizes of extuded section and fixed of 150 mm long size (length of bolt) , complete all as specified and directed by Engineer-in-Charge

Handles 'D' type of size 100 mm ,extruded aluminium alloy , fabricated type anodized , complete all as specified and directed by Engineer-in-Charge

Handles 'D' type of size 150 mm ,extruded aluminium alloy , fabricated type anodized ,complete all as specified and directed by Engineer-in- Charge.

Aluminum alloy, anodized, sliding door bolt with hasp staple ( bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminum alloy and fixed length of bolt 300 mm, bolts not less than 12mm dia with and including a minimum of 6 bolts not,four on bolt plate and two on staple plate complete (ISI marked ), complete all as specified and directed by Engineer-in-Charge

Prelaminated particle board 18 mm /19 mm thick ,interior grade, prelaminated both sides with decorative choice lamination for wooden and fixed with screws to timber frame as in cupboards, shutters, shelves, pelmet etc. including fixing 18 mm wide 6 mm thick beading of Ist class HW (Teak) all around in and including dismantling of old board ,complete all as specified and directed by Engineer-in- Charge.

Continuous (Piano) hinges, width of flaps (when open ) 30mm, stainless steel bright finish or electro galvanised, ISI Marked fixed as in repair ,complete all as specified and directed by Engineer-in- Charge.

Hasp & staple of 100mm size , safety type aluminium anodized with mild steel hinge pin including bolt to hinge plate and fixed with screws ,complete all as specified and directed by Engineer-in- Charge.

Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor of overall length of cover plate 140mm fixed as in repair, complete all as specified and directed by Engineer-in-Charge

300mm long ordinary rat tail rod pattern MS door springs including roller and roller plate , complete all as specified and directed by Engineer-in-Charge

300mm long ordinary rat tail rod pattern MS door springs including roller and roller plate fixed as in repair, complete all as specified and directed by Engineer-in-Charge

Door seal 50mm wide and 1 m in lenth built in aluminium black plate with nylon brush fixed with screws fixed as in repairs, complete all as specified and directed by Engineer-in-Charge.

Sheet glass 3 mm thick, ordinary quality and glazing with oil putty or wooden bead in squares not exceeding 0.5 Sq. m in each pane ,complete all as specified and directed by Engineer-in- Charge.

Figured glass 3 mm thick, pin headed tyoe and glazing with oil putty or wooden bead in squares not exceeding 0.5 Sq. m in each pane,complete all as specified and directed by Engineer-in- Charge. Note for ser item No from 64 to 65 : The rate quoted by contractor is deemed to be included necessary scaffolding and form work as required upto triple storey building.

Stainless, steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staples or fixed to wooden bead , complete all as specified and directed by Engineer-in-Charge.

Framed work as in doors/Chowkhats or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete ( Fe-290,Gde-E-165)in and including dismantling of structural steel work including doors, gates but excluding framed truss etc., complete all as specified and directed by the Engineer-in-Charge.

M S work as Framed works such as grills, gratings etc with ends of bars shouldered and/or riveted, or forged into spikes,framed guard bars barred iron doors ladders, framed balusters walk ways railing, framed work of water tanks, framed and hung as gates including pintle hinges, stops, hand made sliding sliding bolts etc ,drilling bolting or reveting etc and similar work conforming Fe-290 Gde E-165 in and including dismantlingexisting grill ,complete all as specified and directed by Engineer-in- Charge.

Preparation of new or previously untreated wooden surfaces of any description , not otherwise described over 10 cm width or girth and applying two coats of synthetic enamells paint over one coat of red pink primer,complete all as specified and directed by the Engineer in Charge.

Preparation of new or previously untreated steel surfaces of any description , not otherwise described over 10 cm width or girth and applying two coats of synthetic enamells paint over one coat of red oxide primer,complete all as specified and directed by the Engineer in Charge.

Preparation of new or previously untreated steel surfaces of any description , not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over previously primed surfaces ,complete all as specified and directed by the Engineer in Charge.

Steel water tubing, 15 mm bore medium grade ISI Marked, galvanized with all fittings and fixed complete to walls, ceiling or laid in floors in and including taking up or down existing unservicable tubing and connections, cleaning for re fixing or removal to store, complete all as specified and directed by Engineer-in-Charge. Notes: (i) Servicable steel water tubing retrived from taking down of this item shall be used after proper cleaning and washing of old GI tube under item No.73.00 below. Nothing extra payment will be paid on this account . (ii) Fittings & specials as required shall be provided by the contractor. Contractor's rate shall be deemed to include the cost of fittings provided.

Re-fixing of servicable steel water tubing of 15 mm bore, with all fittings at new or old position, laid in floor along wall or at ceiling in and including taking up or down servicable steel water tubing and connections ,complete all as specified and directed by Engineer-in- Charge. Notes: (i) Servicable steel water tubing retrived from taking down of No.72.00 above and this item shall be used after proper cleaning and washing of old GI tube under this.Nothing extra payment will be paid on this account . (ii) Fittings & specials as required shall be provided by the contractor. Contractor's rate shall be deemed to include the cost of fittings provided.

Steel water tubing, 20 mm bore medium grade ISI Marked , galvanized with all fittings and fixed complete to walls, ceiling or laid in floors in and including taking up or down existing unservicable tubing and connections, cleaning for re fixing or removal to store, complete all as specified and directed by Engineer-in-Charge. Notes: (i) Servicable steel water tubing retrived from taking down of this item shall be used after proper cleaning and washing of old GI tube under item No.75.00 below. Nothing extra payment will be paid on this account . (ii) Fittings & specials as required shall be provided by the contractor. Contractor's rate shall be deemed to include the cost of fittings provided.

Re-fixing of servicable steel water tubing of 20 mm bore, with all fittings at new or old position, laid in floor along wall or at ceiling in and including taking up or down servicable steel water tubing and connections ,complete all as specified and directed by Engineer-in- Charge. Notes: (i) Servicable steel water tubing retrived from taking down of No.74.00 above and this item shall be used after proper cleaning and washing of old GI tube under this.Nothing extra payment will be paid on this account . (ii) Fittings & specials as required shall be provided by the contractor. Contractor's rate shall be deemed to include the cost of fittings provided.

Rotational moulded PVC, tripple layered, water storage tanks of capacity 500 litre (cylindrical vertical with closed top), ISI Marked, hoisted and fixed in position, with & including all fittings such as GI tank nipple etc. including ball brass valve of 20 mm bore,high pressure,with polythene float and flynut in and including dismantling PVC water tanks exc 250 ltr but n. exc 500 ltr capacity by disconnecting existing water connection and removal from site ,complete all as specified and directed by Engineer-in- Charge.

Stop valve /Angle cock, 15 mm bore fancy type chromium plated cast copper alloy, screwed down,high pressure,with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed as in repair, complete all as specified and directed by Engineer-in-Charge.

Bib cock long body with flange,15 mm bore fancy type cast copper alloy Chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed as in repair, complete all as specified and directed by Engineer-in-Charge.

Pillar cock, lobg neck fancy type cast copper alloy , with capstan heads, chromium plated , screwed down for 15 mm bore pipe,high pressure , with or without l'ettered ' 'HOT' or 'COLD' with long screwed shanks and fly-nuts , screwed for iron pipe fixed as in repair , complete all as specified and directed by the Engineer in -Charge.

Wall mixer with L bend (provision for over head shower), cast copper alloy, chromium plated for mixing hot and cold water, screwed down for 15mm bore iron pipe and fixed as in repair, complete all as specified and directed by Engineer-in-Charge.

Brass CP central hole basin mixer with 450mm braided connection pipe (without pop-up) for mixing hot & cold water for 15mm bore iron pipe and fixed as in repair, complete all as specified and directed by Engineer-in-Charge.

Brass chromium plated shower rose 125mm with shower arm 15mm size, 195mm long with bend of 45 degree with flange including fixing to steel pipe or union fixed as in repair , complete all as specified and directed by the Engineer in -Charge. Note for Srl Item No 77 to 82:-The quoted rates against these items shall deemed to be included for replacement of damaged GI/Kitec fitting such as socket, elbow,nipple and tee of required size ,fitted/connected and making good any leakage. Nothing extra shall be admissible on this account.

Bib tap standard of PTMT of 15 mm Bore dia of pipe in any colour long body high pressure screwed for iron pipe or GI/Kitec fiiting (minimum weight 15 mm- 105 gms) fixed as in repair , complete all as specified and directed by the Engineer in -Charge.

Angle Stop valve of PTMT of 15 mm Bore dia of pipe in any colour high pressure screwed for iron pipe or GI/Kitec fiiting (minimum weight 15 mm- 90 gms) fixed as in repair , complete all as specified and directed by the Engineer in -Charge.

Wash basins ,vitreous china, white,rectangular type of size 550x400mm including brackets and cutting for and pinning in ends of brackets or erecting stand 32mm dia Waste fittings, brass, chromium plated for glazed basins with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed inluding new brackets fixed as in repair , complete all as specified and directed by the Engineer in -Charge.

Vitreous China squating pan, 'Orissa' pattern, size 580x440mm white, with integral foot rests, including 100mm cast iron 'P' or 'S' trap and 100mm cast iron sanitary connection socket to fit WC outlet including connection to trap, to flushing pipe, anti-syphonage pipe etc. complete including making good to floor fixed as in repair , complete all as specified and directed by the Engineer in -Charge. Note :- Qty and Rates are inclusive of for both P type and S type Traps as on actual required basis on ground

Vitreous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) including connection to trap,and to flushing pipe, anti-syphonage pipe,etc including 100mm cast iron 'P' or 'S' trap complete including making good to floor fixed as in repair , complete all as specified and directed by the Engineer in -Charge. Note :- Qty and Rates are inclusive of for both P type and S type Traps as on actual required basis on ground

PVC valveless , syphonic action type flushing cisterns 10 ltrs capacity , low level , white, with inlet ball valves , float and handle including brackets and pvc flush pipe 32 mm dia for low level fixed as in repair , complete all as specified and directed by the Engineer in -Charge.

PVC connections 15mm size with PTMT nuts of length 600 mm fixed as in repair , complete all as specified and directed by the Engineer in -Charge.

Plastic water closet seat cover good quality in white colour with flat bottom and cover and mild steel chromium plated or aluminium hinging devices, connected to drains outlet, fixed as in repair , complete all as specified and directed by the Engineer in -Charge.

Hand shower (Health foucet) (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position fixed as in repair , complete all as specified and directed by the Engineer in -Charge.

PVC waste pipe flexible for Sink/ WHB of 32mm size fixed as in repair , complete all as specified and directed by the Engineer in -Charge.

PVC cabinet mirror of size 400mmx500mm fixed as in repair,complete all as specified and directed by Engineer-in- Charge. Note : Colour and pattern of cabinet shall be approved by Garrision Engineer.

Taking down and Refixing of WHB/SINK to existing position including change of rusted bracket/ fastener as required at site, including refixing of existing piller tap/PVC connection/waste pipe/grating/bib tap etc and making good with white cement/grey cement to match existing surface , complete all as specified and directed by the Engineer in -Charge.

CP grating 125 mm dia/hinged of brass and fixing with cement mortar 1:3 with/without holes as required fixed as in repair,complete all as specified and directed by Engineer-in- Charge.

Towel rail 600 mm long, 20 mm dia, ‘D’ type, brass chromium plated, fixed to walls with screws and plastic cleats fixed as in repair,complete all as specified and directed by Engineer-in- Charge.

Kitchen plate rack made of stainless steel 1 mm thick with plugs washers as overall size of 31cm x 30x10 inches including fixing to wall and all assessaries fixed as in repair,complete all as specified and directed by Engineer-in- Charge.

Kitchen sinks with drainage board made of stainless steel 1 mm thick with plugs washers and waster including beeding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe upto 0.50 sqm each overall size 915mm x 460 mm bowl size 410 mm x 330 mm x 160mm fixed as in repair,complete all as specified and directed by Engineer-in- Charge.

Finials/Brackets for curtain rod of any size and shape as required at site fixed as in repair,complete all as specified and directed by Engineer-in- Charge.

Drapery rod of mild steel 25mm dia, ribbed/fancy type, powder coated, any shade, including set of fixing brackets, for span not exceeding 2m, fixed to wall with PVC finols/finnels, connected accessaries, rubber packing, required screws and PVC rawal plugs as required fixed as in repair ,complete all as specified and directed by Engineer-in- Charge.

Disconnecting existing tanks of capacity exceeding 250ltrs but n. exceeding 500ltrs, draining out of water, setting a side( or lowering if required) for repair/cleaning and removing accumulated sluge/dirt scales from tank bottom, side and from mouths of circulating pipes of service tanks located on roof of building and disinfecting the tank using bleaching powder to make the tank bacteria free, writing by stencil date of cleaning of tank with white synthetic enemel paint on black ground "Cleaned on (date)" height of words100mm, and hoisting if required, refixing and reconnecting in position after cleaning and removal of rubbbish outside MOD land,complete all as specified and directed by Engineer-in- Charge.

PVC (SWR) pipes 110 mm bore single socketed in any length with ruber rings joints fixed to walls with necessary brackets and making good the mouth of rain water pipe including taking down old pipes ,complete all as specified and directed by Engineer-in- Charge.

PVC (SWR) bends any radius 110mm bore fixed with solvent cement in any position as per site requirement fixed as in repair , complete all as specified and directed by Engineer-in-Charge.

Stack clamps out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof of 110mm bore of pipe fixed as in repair , complete all as specified and directed by Engineer-in-Charge.

Welding in repair exc 2.5 cm but n exc 5.00 cm in length thickness of metal to be welded n.exc 6mm, including cleaning, preparing the surfaces and holding the member in true position for maintenance of steel items such as gates, grills, doors window etc. ,complete all as specified and directed by Engineer-in- Charge.

Cast iron soil, waste and vent pipe ,75 mm bore of spun pipe in any length with or without ears, with cement joints, including epoxy coated inside & out side laid in trenches or in wall including neccesary fiiting arrangement in and including dismantling of cast iron work of any description,complete all as specified and directed by Engineer-in- Charge.

Cast iron soil, waste and vent pipe ,100 mm bore of spun pipe in any length with or without ears, with cement joints, including epoxy coated inside & out side laid in trenches or in wall including neccesary fiiting arrangement in and including dismantling of cast iron work of any description,complete all as specified and directed by Engineer-in- Charge.

Cast iron bends 75mm dia bore, diminishing pieces or tapers ISI marked fixed as in repairs (larger bore measured) ,complete all as specified and directed by Engineer-in- Charge.

Cast iron bends 100mm dia bore, diminishing pieces or tapers ISI marked fixed as in repairs (larger bore measured) ,complete all as specified and directed by Engineer-in- Charge.

Cast iron branch pieces 100mm dia bore, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches with oval acess door fixed as in repairs,complete all as specified and directed by Engineer-in- Charge.

Cast iron floor trap, 75mm dia of out let, ISI marked, with stain less Steel grating including jointing with solvent cement in any position and jointing to waste pipe in Plain cement concrete (1:2:4) type B-1 fixed as in repair,complete all as specified and directed by Engineer-in- Charge.

Cast iron floor trap, 100mm dia of out let, ISI marked, with stain less Steel grating including jointing with solvent cement in any position and jointing to waste pipe in Plain cement concrete (1:2:4) type B-1 fixed as in repair,complete all as specified and directed by Engineer-in- Charge.

Pre-colour coated high tensile strength galvalume sheet roofing with yield strength (550 NPA) prepainted with aluminium (55%) and zinc (45%) alloy coating applied through continous hot dip process having tatal coated thickness (TCT) of 0.50mm with minimum coating mass on both sides @ 150gms/sqm in length and width as per site condition fixed with complete acessories as per manufacturer's instructions through specialist agency and as per profile and shade as approved by GE in and including dismantling plain or corrugated steel /fibre sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings ,complete all as specified and directed by Engineer-in-Charge.

Note :Schedule of credit to be deducted on acceptances of bid.Details of Schedule of credit is given in tender documentse.

MOHAMMAD RASHID (BID ID -3389873)

M/S MANI GARG CONTRACTOR (BID ID -3392045)

B N FRIENDS AND CO (BID ID -3383452)

M/S GOYAL ASSOCIATES (BID ID -3394197)

M/S Bangali Ram (BID ID -3386397)