GE/DE-13/2020-2021

Amount

Demolition, Cement concrete (unreinforced) in ground floors and pavings not exceeding 15cm thickness below or above ground level, complete all as specified and as directed.

Demolition of brick work built in cement mortar including all quoins, arches, pillars etc., but excluding ashlar facings, complete all as specified and as directed.

Taking down cement plaster from brick or concrete surfaces including raking out joints, hacking for key and scrubbing down with water, complete all as specified and as directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) not exceeding 1.5Sqm each and removing to store, complete all as specified and as directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) exceeding 1.5Sqm but not exceeding 4Sqm each and removing to store, complete all as specified and as directed.

Taking down shutters of any description exceeding 1Sqm and not exceeding 2Sqm each, complete all as specified and as directed.

Dismantling Asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings, complete all as specified and as directed.

Dismantling floor, hearth or wall ceramic tiling including cement mortar bedding (but not backing) and rubbish off the premises, complete all as specified and as directed.

Dismantling timber work in scantlings exceeding 40Sqcm and over in section framed work, complete all as specified and as directed.

Plain cement concrete 1:2:4 type B-1 using 20mm graded crushed stone aggregate, as in kerb stones, mud stops and similar items including weathering, slightly rounded or chamfered angles and throating on top of chajjas, rails, cills etc., including necessary form work required if any, complete all as specified and as directed.

Providing precast reinforced cement concrete 1:2:4 type B1 using 20mm graded crushed stone aggregate in louvers and jallies, 25 mm thick (measured solid), including all mouldings but excluding frame (precast frame shall be measured separately) set in cement mortar 1:4, fixed in repairs, complete all as specified and as directed.

Precast RCC coping 50mm thick and 250mm wide in cement concrete 1:2:4 type B-0 using 12.5mm graded crushed stone aggregate including necessary moulds and grooves as required in shape and size, complete all as specified and as directed.

Brickwork with sub class `B` bricks, in straight or curved on plan exceeding 6m mean radius, built in CM 1:6, complete all as specified and as directed.

Second class soft wood in scantiling, clean sawn timber framed and fixed with nails, complete all as specified and as directed.

2nd class hardwood plain fillets square, rectangular or triangular in section of size exceeding 3Sqcm but not exceeding 6Sqcm clean sawn, fixed in repairs, complete all as specified and as directed.

2nd class hard wood plain fillets square, rectangular or triangular in section clean sawn area of size exceeding 6Sqcm but not exceeding 13Sqcm clean sawn, secured with nails or beads, fixed in repairs, complete all as specified and as directed.

25mm thick flush shutters factory made solid core construction with block board core and plywood face panels commercial type on both sides, complete all as specified and as directed.

Factory made 35mm thick second class hard wood for plain framed panelled shutters (any number of panels) with lock rail and panel of 12mm veneered particle board with commercial veneering on both faces. The size of rail & style as per IS: 1003(Part 1), kiln seasoned and chemically pressure treated, complete all as specified and as directed.

Glazed and Skelton shutters using 2nd class hard wood, 35mm thick open rebated and prepared to receive glass or gauge etc., edges of framing plain and chamfered or fitted with cut or mitered beads for securing glass or gauze, size of member of shutter as specified in SSR Part-I section 8, clause 8.23(a) and divided in square complete all as specified and as directed.

Solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet, reinforced with M.S. square tube supplying and fixing in opening as per specification & drawing complete all as specified and as directed.

Factory made solid PVC moulded door shutter 30mm thick (style ) consisting of frame made out of M.S frame shall be covered with heat moulded plain colour PVC'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail lock rail & bottom rail on either side & as gap insert for rail & bottom rail; panelling of plain colour PVC sheet to be fitted in the M.S frame welded/ sealed to the stiles & rail with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification, complete all as specified and as directed.

100 mm size but hinges medium weight cold rolled mild steel fixed complete all as specified and as directed.

150mm size aluminium anodized, barrel tower bolts of extruded section complete all as specified and as directed.

150mm size aluminium anodized, handles cast type, complete all as specified and as directed.

250 mm size aluminium alloy anodised sliding door bolt with haps, staple ( bolt type ) and fixing clips of sheet, cast of extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy, fixed in repair complete all as specified and as directed.

300 mm size aluminium alloy anodised sliding door bolt with haps, staple ( bolt type ) and fixing clips of sheet, cast of extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy, fixed in repair complete all as specified and as directed.

Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B- 21 of size 100mm, complete all as specified and as directed.

Steel handles for left & Right leafs including nuts, washers etc., fixed in repairs, complete all as specified and as directed by Engr-In-charge.

Cast iron(malleable) or mild steel casement stays, size 300mm with hinged joint, two plates and studs, fixed in repairs, complete all as specified and as directed by the Engineer-in-Charge.

Drapery rod 25mm dia aluminum, powder coated teak wood texture finish 1mm thick, with end bulbs rings of required size including fixing bracket, complete all as specified and as directed.

Galvanised mild steel wire cloth 0.63mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or galvanised wire staples, complete all as specified and as directed.

Galvanised mild steel wire cloth 0.63mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or galvanised wire staples, fixed in repairs, complete all as specified and as directed.

Aluminium alloy powder coated (50 micron) anodized door frame of section 100mm x 44 mm x 2 mm thick, door shutter of aluminium section of size 85 mm x 44 mm x 2 mm thick, top rail and both styles of size 100 mm x 44 mm x 2 mm thick, lock rail and bottom rail of size 115 mm x 44 mm x 2mm thick incl aluminium anodized snap beading and rubber packing & 5.5 mm thick colour designer glass incl 200 mm long tower bolt-2 Nos, 200 mm long Alm handle -02 Nos on each leaf, 4 lever lock brass 100 mm long mortice lock (Make :- Godrej), & double action floor door spring(Sandhu/Samrat) heavy duty suitable for 1 m wide shutter for each leaf, complete all as specified and as directed.

Aluminium alloy powder coated any tint standard hollow section with special powder coated coloured or any tint window frame with one glazed shutter (fixed) and two Nos glazed and wire gauged shutter sliding type with aluminium section as per series A(15mm) 3 track of Jindal section number of sliding windows, with framed shutter including aluminium alloy powder coated snap type beads handles aluminium powder coated barrel tower bolts & glazing clips. joints cleats rubber gaskets etc compl all as specified including provision of 5.5 mm thick tinted glass of superior quality and stainless steel wire cloth of 0.36 mm nominal dia wire and average width of aperture 1.4 mm and aluminium grill including all standard fittings, complete all as specified and as directed.

Aluminium powder coated window and ventilator shutter fixed type with sash bar, aluminium section weighing 0.55kg/m including necessary joining cleates , glazing clips, rubber packing, anodised aluminium snap beading screw sets, complete all as specified and as directed.

Aluminium anodized decorative grills with mesh size 30mm x 30mm made ouit of 6mm-5mm thick aluminium section with fixing rails of aluminium channels 12-15mm, complete all as specified and as directed.

Taking down aluminium door shutter and refixing after necessary repairs like securing glass and beads, complete all as specified and as directed.

Mild steel framed work as in doors (as in chowkats) or gates of angle or other section with gusset plates, rails, braces etc., inclusive of 1.25mm thick steel sheeting or other covering hanging or fastening and fixing complete conforming to Gde Fe-410-0 or Fe-310-0 including shop coat of red oxide including preparation of surface before fixing, complete all as specified and as directed.

Mild steel framed work as in grills, gratings etc., with ends of bars shouldered and or riveted or forged into spikes, framed guard bars, barred iron doors, ladder, framed balusters, railing, frame work for water tanks and similar work, complete conforming to Fe 290 Gde-E-165 including shop coat of red oxide including preparation of surface before fixing, complete all as specified and as directed.

1.00mm thick mild steel, plain & black sheet in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40mm lap joints with riveted or welded seams, including bending or turning up, mitred angles etc. as required, complete all as specified and as directed.

Mild steel rolled sections Fe-410w (Gde-E-250) quality 'B' Roof trusses (framed ), trussed, purlins, crane gantries , rails and fastening and havey bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces cleats etc., fixed in repairs, complete all as specified and as directed.

Box type Steel windows with double shutters (inside for wiremesh & out side for glass), hinges, steel handle, tower bolt and steel peg stay complete with glazing bars dovetailed or welded including a coat of red oxide after preparation of surface before fixing all as shown in drg No. TD-A sheet 1/3 to 3/3, complete all as specified and as directed.

Box type Steel windows with double shutters (inside for wiremesh & out side for glass), hinges, steel handle, tower bolt and steel peg stay complete without glazing bars dovetailed or welded including provision for AC/desert cooler opening and cover including a coat of red oxide after preparation of surface before fixing all as shown in drg No. TD-A sheet 1/3 to 3/3, complete all as specified and as directed.

Pre-Painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering /cladding to wall, fixed with self tapping screws including dismantling Asbestos cement (corrugated, semi corrugated, etc.) sheets in roof coverings, fixed in repairs, complete all as specified and as directed.

Pre-Painted galvalume aluminium zinc coating GI based Plain steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering /cladding to wall/ridge, fixed with self tapping screws, fixed in repairs, complete all as specified and as directed.

Asbestos cement two -piece plain adjustable plain wing ridge 6mm thick, fixed in repairs, complete all as specified and as directed.

Taking down existing roof treatment any type including screed bed, if any and hacking for key, scrubbing down wih water including cleaning and clearing roof of all the rubbish. Rendering on top of concrete roofs with 15mm thick cement mortar in 1:4. Cleaning the plastered surface after drying from dirt, mortar, dust mortar buds, algae and all other foreign matter and brushed and wiped. Apply evenly a coat of bituminous primer conforming to IS- 3384 @ 0.4Kg/Sqm. Over the primed surface apply a coat of hot blown 85/25 penetration grade bitumen conforming to IS- 702 @ 1.2 Kg/Sqm of the surface area. applying APP based polymeric mambrane minimum weighting 3kg/sqm and minimum 3mm thick reiforced with polyster non wove febric ( wt.not less than 150grm/sqm ). APP membrane will be laid across the slope from lowest line of roof towards ridge with over laps of 75mm in length side and 100mm on the width side of membrane bonded with hot blown bitumen. Over the APP membrane apply semi hot blown 85/25 penetration grade bitumen conforming to IS- 702 @ 0.5 Kg/Sqm and provide final layer of 20mm screed bed in cement mortar 20mm thick. complete all as specified and as directed.

Snap grid ceiling with 4 mm thick E Board of approved size 600mm x 600mm supported and including ceiling frame of alluminium alloy anodized angle 25mm x25mm x 1.5mm at edge and tee section 25mm x 38mm x 1.5mm at edges and edges placed both way at spacing 600mm center to center including necessary aluminium alloy anodized cleats and 3mm dia GI wire suspender fixed to ceiling not exceeding 120cm center to center both ways including two coats of OBD on one side of ceiling boards including dismantling of old ceiling of any size and any description including cover fillets, complete all as specified and as directed.

False celling 4mm thick AC Plain building board, fixed to frame work in ceilings, including dismantling of old ceiling of any size and any description including cover fillets, complete all as specified and as directed.

100 mm thick plain cement concrete 1:2:4 type B-1, using 20mm graded crushed stone aggregate as in floors finished even and smooth without using extra cement, complete all as specified and as directed.

Supply only glass dividing strips, 38mm wide and 3mm thick, inserted in position to conform to design, complete all as specified and as directed.

75mm thick PCC 1:3:6 type C-2 (using 40mm graded crushed stone aggregate) as in plinth protection including finishing the surface even and fair, complete all as specified and as directed.

Machine cut kota stone slab 18 to 20 mm thick as in flooring laid over and including cement screed base 15mm thick in cement mortar 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing, complete all as specified and as directed

Vibro compacted Precast concrete interlocking paver blocks, factory made,any shape and size conforming to IS- 15658- 2006 of 80mm thick, M-40 Grade set, jointed in neat cement slurry and pointed flush with grey cement mixed with pigments to match colour of blocks in floors laid over 30mm thick sand cushioning including dismantling old paver blocks set in cement mortar, complete all as specified and as directed.

Pre-polished coloured chequered cement concrete tiles, factory made, Premium quality 250mm x 250mm x 25mm thick, set, jointed in neat cement slurry and pointed flush with grey cement mixed with pigments to match colour of blocks in floors over 15 mm thick screed bed or bedding layer in cement mortar 1:4 including dismantling old tiles set in cement mortar, complete all as specified and as directed.

Non-Skid coloured ceramic tiles 6 to 7mm thick (square/rectangular) area of each tiles exceeding 0.11Sqm but not exceeding 0.18 Sqm in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match incl 15mm thick screed bed in cement mortar 1:4 including dismantling of old tiles with backing, complete all as specified and as directed

Glazed ceramic tiles in vertical surface 300mm x 450mm x 7 mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match including 10mm thick rendering in cement mortar 1:4 including dismantling of old tiles with backing, complete all as specified and as directed.

Vitrified ceramic tiles light colour 10mm thick (square/rectangular) polished, area of tiles not exceeding 0.36Sqm each in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in cement mortar 1:4 including dismantling of old tiles with backing, complete all as specified and as directed.

Rendering 15 mm thick in cement mortar 1:6 finished even and smooth without using extra cement, complete all as specified and as directed.

Rendering 15mm thick cement plastering in cement mortar 1:4 on brick/concrete surface of walls including finished even and smooth without using extra cement, complete all as specified and as directed.

Rendering 5mm thick cement plastering in cement mortar 1:3 on ceilings including finished even and smooth without using extra cement, complete all as specified and as directed.

Complete removal of existing treatments, washing, rubbing down and stopping of distempered and pointed surfaces , preparing surfaces including 3mm thick Birla white Putty up to the surface should be smooth, complete all as specified and as directed by Engr-In-Charge.

Apply two coat of oil bound distemper on old plaster or unplaster surfaces including preparation etc., complete all as specified and as directed by Engr-In-Charge.

Preparing old surfaces (plastered) or un plastered of walls and applying two coats of cement base paint, complete all as specified and as directed by Engr-In-Charge.

Applying three coats of white washing on cealing including chalk whiting, preparation etc., complete all as specified and as directed by Engr-In-Charge.

Preparation of newly plastered or unplastered surface of walls and applying two coats of oil bound distemper over a coat of primer as on walls, complete all as specified and as directed.

Preparation of newly plastered surfaces of walls and applying two coat of cement based paint, complete all as specified and as directed.

Preparation of old paint steel surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint, complete all as specified.

Preparation of new steel surfaces of any description, not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide, complete all as specified and as directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frame, glazed with putty or fixed with board complete all as specified and as directed.

Sheet glass 3 mm thick ordinary quality and glazing with oil putty or wooden beads not exceeding 0.5 Sqm in each pane, complete all as specified and as directed.

Three layered heavy duty blow moulded Rotational moulded polyethene water storage tank 500 ltr capacity hoisted and fixed in position having 20mm dia PVC float valve, including dismantling of existing tank, complete all as specified and as directed.

Three layered heavy duty blow moulded Rotational moulded polyethene water storage tank 1000 ltr capacity hoisted and fixed in position having 20mm dia PVC float valve, including dismantling of existing tank, complete all as specified and as directed.

14mm bore GI tubing (medium grade) with all fittings and fixed complete to walls and ceiling or laid in floors/roofs including taking down old tubing, complete all as specified and as directed.

20mm bore GI tubing (medium grade) with all fittings and fixed complete to walls and ceiling or laid in floors/roofs including taking down old tubing, complete all as specified and as directed.

Vitreous china wash down closet pan (pedestal pattern), white with "S" trap, including plastic seat and cover and connecting to outgoing pipe, flush pipe and anti syphonage pipe, fixed in repairs, complete all as specified and as directed.

Vitreous china squatting pan ‘Orissa’ pattern size 580 x 440 mm white with integral foot rests including P or S trap including provn of lime concrete bedding including connections to flushing cistern/pipe, fixed in repairs, complete all as specified and as directed.

Vitreous china wash hand basin, white flat back size 550mm x 450mm including waste pipe, brackets and 32mm dia bore CP coupling, complete fixed in repairs, complete all as specified and as directed.

PVC valve less syphonic action type coloured flushing cistern, low level, 10 litres capacity including flush pipe PVC connection, float valve, PVC handle/button and connections complete including taking down old unserviceable flushing cistern any type, fixed in repairs, complete all as specified and as directed.

Stop valve cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipes or for unions and fixed to 15mm bore of pipe, fixed in repairs complete all as specified and as directed.

15mm bore PVC connection of size 450mm long 15mm bore with PTMT end nuts, fixed in repairs, complete all as specified and as directed.

20mm bore ball valves high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball, screwed for iron pipe and fixed minimum weight -210gms, fixed in repairs, complete all as specified and as directed.

15mm bore ball valves high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball, screwed for iron pipe and fixed minimum weight -142gms, fixed in repairs, complete all as specified and as directed.

15mm bib tap standard of PTMT any colour high pressure screwed for iron pipe and fixed . (Minimum weight 15mm-90gms), fixed in repairs, complete all as specified and as directed.

15mm bore stop valve of PTMT any colour high pressure screwed for iron pipe . (Minimum weight 15mm-90gms / 20mm-125gms) fixed in repairs complete all as specified and as directed.

32mm dia PVC waste pipe for wash hand basin fixed in repairs complete all as specified and as directed.

CP grating with or without hole 100 mm dia, fixed in repairs, complete all as specified and as directed.

15mm bore bib tap chromium plated brass, Fancy type with crutch or butter fly handle, screwed down, screwed for iron pipe or for brass ferrule, fixed in repairs, complete all as specified and as directed.

NOTE:- For minimum fair wages ,EPF and payment to labour employed, refer Sch A Note No-17,18 and Special Condition No 5 & 21.2 of this tender. Contractor must produce all the relevent record such as payment made to labour, EPF etc at the time of payment of RARs/Final bill. No payment will be released to contrator without producing the proper record.

NOTE:- Irrespective of whatever specified elsewhere in tender documents, all the debris/waste materials produced out of above mentioned work shall be removed out of Cantonement land and disposed off at locations notified by the Delhi Cantonment Board for disposal of waste building materials within NCR area, without any extra cost to Department under own arrangement of contractors. The rates quoted by the contractors against the items catered here-in-above in the BOQ are inclusive of said provision.

Simran construction Company

M/s Durga Traders

MAA SANTOSHI ENTERPRISES

sunil traders

R. S. Associates

Vipul Construction

M/s KUNDU CONSTRUCTION

S GOURAV PRAKASH ENTERPRISES

M/s Shubh Enterprises