Carrying out Civil and Electrical Works pertaining to Renovation of Kitchen Area of Executive Canteen at ARDC HAL DC

HINDUSTAN AERONAUTICS LIMITED BANGALORE FACILITIES MANAGEMENT DIVISION

NAME OF THE WORK: Carrying out Civil and Electrical Works pertaining to Renovation of Kitchen Area of Executive Canteen at ARDC, HAL [DC]. Cont. No: HAL/FMD/R-142/24-25

Name of the Contractor :

Sl. No. Specification Quantity Unit Rate in Figs [Excluding GST] Rate in Words Amount

Preamble: (1) The subject work has been called on works contract basis and prevailing GST for same is 18%. Any change in GST +/- during the currency of contract shall be on HAL account. The Tenderer shall abide by prevailing GST act. (2) L1 (lowest quote) will be determined based on the total quoted amount including GST. (3) This BOQ specification has to be read in conjunction with relevant CPWD specifications amended upto date/ detailed technical specification in tender document and tender drawings if any.

Part 'I' - Civil works

1 Disposal of surplus earth/moorum/building rubbish/ malba/ similar unserviceable, dismantled or waste material of partitions,ceiling boards,tiles,frames etc by mechanical transport including loading, transporting, unloading in all lifts/loads upt 10 km distance from HAL. completely as per directions of Engineer-in-charge. 50.00 Cum 0.00

2 Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains, pipes, cables etc. in all kinds of soils (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lifts, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m with all labour, tools & tackles, plant & machinery, hire & fuel charges etc., all complete as directed by Engineer-incharge. 50.00 Cu m 0.00

3 Returning / filling in with useful excavated soil (excluding rock), free from salts, organic or other deleterious matter (Other than black cotton soil & rock etc., in trenches, plinth,sides of foundations etc., spreading in layers not exceeding 20 cm thick, watering, breaking / removing clods exceeding 50 mm, ramming and consolidation of each deposited layer etc., with all labour, tools & tackles, plant & machinery, etc., lead upto 50 m and for all lifts, all complete as directed by the Engineer-in-Charge. 50.00 Cu m 0.00

4 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:4:8 (1 Cement : 4 coarse sand : 8 graded stone aggregate 40mm nominal size) 7.00 Cum 0.00

5 Supplying, mixing and placing plain cement concrete (1:2:4) (1 Cement : 2 coarse sand derived from natural sources : 4 graded stone aggregate) of required thickness using 20 mm nominal size down graded hard stone/granite aggregate in accordance with IS 456 in posts, struts, buttresses, string or lacing courses,parapets, coping, bed blocks, anchor blocks, plain window sills, fillets,sunken floor etc including formwork, mechanical mixing, transporting, vibrating, consolidation, levelling, curing, dewatering if any, all materials, labour, lead & lift, tools, plant & machinery, keeping concrete well wetted during the curing period and protecting it in extreme weather conditions etc., but excluding the cost of centering, shuttering and finishing, all complete as directed by the Engineer-in-Charge. 25.00 Cum 0.00

6 Construction of size stone masonry in cement mortar (1:6) at all levels, in courses not less than 15 cm high with bond stones at 1.4 to 1.8 m apart in each course, solidly hearted faces, beds and joints squared back, raking out joints 10 mm deep, curing, providing weep holes if any etc., all complete as directed by the Engineer-in-Charge. 8.00 Cum 0.00

7 Brick work with 230mm/115mm thick common burnt clay machine moulded modular bricks of class designation 7.5 in brick work above plinth level including making horizontal and vertical grooves 10 mm wide 12 mm deep complete in cement mortar 1:6 (1 cement : 6 coarse sand) all complete as directed by the Engineer-in-Charge. 40.00 Cum 0.00

8 Steel reinforcement for R.C.C work including straightening, cutting,bending,placing in position and binding all complete upto plinth level.Thermo-Mechanically Treated bars of grade Fe-500D all complete as directed by the Engineer-in-Charge. 250.00 Kgs 0.00

9 Centring and shuttering including strutting, propping etc. and removal of form for:removal of form for: Foundations, footings, bases of columns etc. for mass concrete.

a)Foundations, footings, bases of columns etc. for mass concrete. 6.00 Sqm 0.00

b)Lintels, beams, plinth beams, girders, bressumers and cantilevers. 25.00 Sqm 0.00

10 Structural steel work riveted, bolted or welded in built up sections, trusses and framed work using members like MS members made up of elements like ISMB,ISMC, ISA, MS Flats, ISNT, MS Plates, holding down bolts, nuts, washer, etc , including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. 5000.00 Kgs 0.00

11 Providing and fixing Granite stone slab of with (18mm to 25mm thick), area of slab not less than 0.5sqm, like Ruby Red/Black/Cherry with gang saw cut, mirror polished, premoulded and prepolished, machine cut for urinal partitions,platforms, vanity counters, and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels as per direction of Engineer-in-charge. 5.00 Sqm 0.00

12 Providing and fixing Ceramic glazed wall tiles(Light/dark shade) conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black , in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade of any size as approved by Engineer-in-Charge. 155.00 Sqm 0.00

13 Providing and fixing expansion hold fasteners on C.C. /R.C.C./Brick masonry surface backing including drilling necessary holes and the cost of bolt of Wedge expansion type etc complete as per direction of Engineer-in-charge.

a Fastener with threaded dia 6 mm each 30.75 8.00 Each 0.00

b Fastener with threaded dia 10 mm each 33.80 8.00 Each 0.00

14 Providing and fixing aluminium work, Powder coated aluminium (minimum thickness of powder coating 50 micron) for partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : 7.00 Kgs 0.00

15 Providing and fixing aluminium work, Powder coated aluminium (minimum thickness of powder coating 50 micron) For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately). 25.00 Kgs 0.00

16 Providing and fixing glazing 5 mm thickness (weight not less than 12.50 kg/sqm) in aluminium/uPVC door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): 3.00 Sqm 0.00

17 Providing and fixing 12mm thick prelaminated particle board with decorative lamination on both sides. flat pressed three layer or graded wood particle board conforming to IS:12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge. 3.00 Sqm 0.00

18 Providing and fixing Hard wood (SAL) for frames of doors, windows, hand rails, frame work for partitions in etc cut to shape and required curvature and preparing the surfaces to receive the polishing fixed in position with hold fast lugs/with dash fasteners of required dia & length/SS Screws at all heights,with necessary moisture content test.complete as per direction of Engineer-in-charge. (Fastners/hold fasts/SS Screws to be paid separately) 0.34 Cum 0.00

19 Providing and fixing factory made uPVC door frame made of uPVC extruded sections42 X 50mm having an overall dimension as below (tolerance±1mm), with wall thickness 2.0 mm (± 0.2 mm), corners of the doorframe to be Jointed with galvanized brackets and stainless steel screws,joints mitred and Plastic welded. The hinge side vertical of the framesreinforced by galvanized M.S. tube of size 19 X 19 mm and 1mm (± 0.1mm) wall thickness and 3 nos. stainless steel hinges fixed to the framecomplete as per manufacturer’s specification and direction of Engineer in-charge 10.00 Rmt 0.00

20 Providing and fixing to existing door frames 24 mm thick factory made PVC door shutters made of styles and rails of a uPVC hollow section of size 59x24 mm and wall thickness 2 mm (± 0.2 mm) with inbuilt edging on both sides. The styles and rails mitred and joint at the corners by means of M.S. galvanised/ plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 20x20 mm and 1 mm (± 0.1 mm) wall thickness. The lock rail made up of 'H' section, a uPVC hollow section of size 100x24 mm and 2 mm (± 0.2 mm) wall thickness, fixed to the shutter styles by means of plastic/galvanised M.S. 'U' cleats. The shutter frame filled with a uPVC multi-chambered singlepanel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall thickness. The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as per manufacturer's specification and direction of Engineer-in-charge. 7.00 Sqm 0.00

21 Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size).complete as per direction of Engineer-in-charge. 10.00 Each 0.00

22 Providing and fixing 35mm thick flush door shutters conforming to IS :2202 (Part I) non-decorative type of approved brand/make, core of block board construction with frame of 1st class hard wood & lipping with 2nd class teak wood battens 25 mm minimum depth on all edges and well matched commercial 3ply veneering with vertical grains or cross bands including ISI marked Stainless Steel butt hinges with necessary screws and face veneers on both faces of shutters and making rectangular vision panel of 0.1sqm with 6 mm thick clear heat strengthened glass.complete as per direction of Engineer-in-charge. 2392.65+462.35+199.15+670*1.1 20.00 Sqm 0.00

a Providing and fixing bright finished brass handles of 125mm size with screws etc.complete: 14.00 Each 0.00

b Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete. 7.00 Each 0.00

c Providing and fixing bright finished brass tower bolts of 250x10mm (barrel type) with necessary screws etc. complete 14.00 Each 0.00

d Providing and fixing bright finished brass 100 mm mortice latch and lock with min. 6levers and a pair of lever handles of approved quality with necessary screws etc. complete. 7.00 Each 0.00

e Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete. 10.00 Each 0.00

f Providing and fixing 20mm dia chromium plated brass curtain rod /Towel rail of 600mm long having wall thickness of 1.25mm with two chromium plated brass brackets fixed with C.P. brass screws and PVC sleeves etc., wherever necessary. 2.00 Rmt 0.00

g Providing and fixing 5.0 mm thick glass panes for doors, windows and clerestory window,ventilators(weight not less than 12.50 kg/sqm),including cutting an dfinishing as per site requirement .All as per the instructions of Engineer Incharge 2.00 Sqm 0.00

23 Providing and laying Ceramic glazed floor tiles of size 300x300 mm(thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick bed of cement mortar1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @3.3kg/sqm including pointing the joints with white cement and matching pigments etc., complete. 20.00 Sqm 0.00

24 Providing and fixing 1st quality ceramic glazed tiles conforming to IS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kgper sqm including pointing the joints with white cement mixed with pigment of matching shade complete. 155.00 Sqm 0.00

25 Providing and fixing Single socketed pipes of 110mm diameter unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A of approved brand, on wall face including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion .complete as per direction of Engineer-in-charge. 25.00 Metre 0.00

26 Providing and fixing Single socketed pipes of 75mm diameter unplasticised Rigid PVC water pipes conforming to IS : 13592 Type A of approved brand, on wall face including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.complete as per direction of Engineer-in-charge. 15.00 Metre 0.00

27 Plastering to brick/block wall with 15 mm thick on the rough side of single or half brick wall of cemnet mortor (1:6) including leveling,curing and making the level smooth and at all heights, complete as per direction of Engineer-in-charge. 600.00 Sqm 0.00

28 Providing and finishing old walls in two or more coats with Premium Acrylic Smooth exterior paint with Silicone additives of approved brand of required shade @ 1.43 ltr/ 10 sqm over existing cement paint surface after Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete as per direction of Engineer-in-charge. 25.15+131.30 200.00 Sqm 0.00

29 Painting newly/old plastered interior surfaces with two coats of low VOC with less that 50 g/litre premium plastic emulsion with acrylic base , of approved make, colour, shade, tint & pattern at all levels, over a water thinnable priming coat with cement primer including preparing the surface by removing loose dirt and any organic growth, smoothening the surface by using suitable emery paper, filling crevices and finishing even by applying one full coat of putty, necessary scaffolding etc., all complete as directed by the Engineer-in-Charge. 142.8+73.95+25.15+156.05 150.00 Sqm 0.00

30 Painting on previously painted interior surfaces with 1 coat of primer and 2 coats of epoxy resin paint (with very good abrasion resistance, excellent chemical resistance to alkalis, solvents, salt (upto 80 degrees centigrade) and water and a continuous temparature resistance of 93 degrees centigrade and intermittent temparature resistance of 120 degrees centigrade ), by maintaining proper inter-coat interval as per the technical data sheet specifications of approved brands like Berger/Asian/Dulux or any equivalent conforming to above specifications, after carrying out the surface preparation works mentioned below. To smoothen the surface approved polyster putty should be applied after application of one coat of primer and next coat to be applied over dried puty. Dried polyster putty to be roughened with emery paper before application of primer.

Surface preparation works prior to painting : previous paint has to be removed by emery paper and wire brush . Degreasing of the oil and grease by using solvent like turpentine and or thinners is to be carried out.Dust is to be removed after mechanical cleaning of the substrate. After surface preparation seal the cracks with approved crack filler and after the curing /drying of the crack filler, the surface has to be roughened with emery paper. The surface should be free from oil, grease, dust, debris, fungus and moss.

The work is to be carried out through specilaised/approved applicators to ensure desired finish along with all necessary safety arrangements like scaffolding, PPEs, working platforms etc Site clearance will be given in a phase wise manner and adequate resources should be deployed based on the site clearances to complete the work within time.

The area has to be carodned off with necessary arrangements like tarpaulin sheets etc to ensure no dust is spread to the surrounding areas.

Prior approval of the make and shade of the paint is to be obtained from EIC with data sheet fulfilling the scope of work. 200.00 Sqmt 0.00

31 Painting on previously painted interior surfaces with 1 coat of approved primer and 2 coats of water borne polyurethane finish paint having antifungal and antibacterial charectaristics and excellent water resistance properties and is water washable ( with Tensile strength of 50kg/sq cm , Elongation at break of : 100% , Wet scrub resistance : Passing of 2000 cycles without failure, Abrasion resistance of 110 mg wt loss maximum (CS 10 wheel with 2 X 1 kg load, 1000 cycles and Flexibility : Passes 0.25" mandrel) by maintaining proper inter coat interval as per the technical data sheet specifications of approved brands like Berger/Asian/Dulux or any equivalent conforming to above specifications , after carrying out the surface preparation works mentioned below. To smoothen the surface, approved cement putty should be used after application of one coat of primer and and the next coat is to be applied over dried putty. Dired cement putty is to be roughened with emery paper before application of primer.

Surface preparation works prior to painting : previous paint has to be removed by emery paper and wire brush . Degreasing of the oil and grease by using solvent like turpentine and or thinners is to be carried out.Dust is to be removed after mechanical cleaning of the substrate. After surface preparation seal the cracks with approved crack filler and after the curing /drying of the crack filler, the surface has to be roughened with emery paper. The surface should be free from oil, grease, dust, debris, fungus and moss.

The work is to be carried out through specilaised/approved applicators to ensure desired finish is obtained along with all necessary safety arrangements like scaffolding, PPEs, working platforms etc.The area has to be carodned off with necessary arrangements like tarpaulin sheets etc to ensure no dust is spread to the surrounding areas. Site clearance will be given in a phase wise manner and adequate resources should be deployed based on the site clearances to complete the work within time.

Prior approval of the make and shade of the paint is to be obtained from EIC with data sheet fulfilling the scope of work. 400.00 Sqmt 0.00

32 Providing and applying synthetic enamel paint for wooden/steel surface in Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture,filling joints,patti etc ,complete as per direction of Engineer-in-charge. 70.35+226.25 40.00 Sqm 0.00

33 Dismantling 15 to 40 mm dia G.I./cpvc pipe including stacking of dismantled pipes (within 50 metres lead) including making temporary arrangements for continuing ongoing services to toilets as per direction of Engineerin-Charge 15.00 RM 0.00

34 Fixing chowkhat in existing opening in brick/ RCC wall with dash, fasteners/Chemical fasteners of appropriate size (3 nos on each vertical member of door chowkhat and 2 nos on each vertical member of window chowkhats), including Cost of dash fasteners/ chemical fastener complete as per direction of Engineer-in-charge. 4.00 Each 0.00

35 Dismantling W.C. Pan of all sizes including disposal of dismantled materials i/c malba,making temporaray arrangements for blocking service lines to avoid water leakages ,all complete as per directions of Engineer-inCharge. 2.00 Each 0.00

36 Repair to plaster of thickness 12mm to 20 mm in patches of area lesser than 2.5 sqm including cutting the patch in proper shape, raking out joints and preparing plastering the wall surface with white cement based polymer modified self curing mortar, including disposal of rubbish, without causing hindrance /protecting the existing floor finish work all complete as per the direction of Engineer-In-Charge. 30.00 Sqm 0.00

37 Disconnecting damaged overhead/terrace PVC water storage tank of any size from water supply line and removing from the terrace including shifting at ground level as per direction of Engineer-in-charge. 1.00 Each 0.00

38 Providing & fixing White vitreous china Orissa pattern water closet squatting pan of approx size (630mm X 450mm) or nearest available size along with "S" or "P" trap including dismantling of old WC seat and "S" or "P" trap at site complete with all operations including all necessary materials, labour and disposal of dismantled material i/c malba, all complete as per the direction of Engineer-incharge 1.00 Each 0.00

39 Demolishing brick work with cement mortar manually/ by mechanical means, after disconnecting the electrical service and AC lines if any, including stacking of serviceable material and disposal.complete as per direction of Engineer-in-charge. 40.00 Cum 0.00

40 Dismantling stone slab flooring laid in cement mortar including stacking of serviceable material and disposal of unserviceable material within 50 metres lead e as per direction of Engineer-in-charge. 100.00 Sqm 0.00

41 Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge.Nominal concrete 1:4:8 or richer mix (i/c equivalent design mix)and including stacking material complete as per direction of Engineer-in-charge. 8.00 Cum 0.00

42 Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead of area 3 sq. metres and below, including stacking material and handing over the useful materials to HAL maintenance department and disconnecting the service lines if any all as instructed by Engineer Incharge. 7.00 Each 0.00

43 Dismantling/removing tile work (for thickness of tiles 10mm to 25mm.) of in floors and in walls laid in cement mortar after disconnecting the electrical service and AC lines if any,including stacking material L, complete as per direction of Engineer-in-charge. 50.00 Sqm 0.00

44 Providing and fixing beveled edge mirror of size 600x450mm of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. 2.00 Each 0.00

45 Providing and fixing Wall hung half pedestal Vitreous China Wash basin size of approx size 630x450 mm fixed with with C.I. brackets/rack bolts , single 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste coupling of standard pattern,k, P.V.C. waste pipe with waste fittings of 40mm dia and make it function of approved brand/make, including painting of fittings and brackets, cutting and making good the walls wherever required.complete as per direction of Engineer-in-charge. 2226.35+116.7+574.3 2.00 Each 0.00

46 Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) of approved brand with ISI marked white solid plastic seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all connecting fittings and fixtures to make it operational completely, including cutting and making good to the walls and floors wherever required complete as per direction of Engineer-in-charge. 1.00 Each 0.00

47 Providing and fixing 8 mm dia C.P. / S.S. Jet (Health Fuacet) with flexible tube upto 1 metre long with S.S. triangular plate on walls/Eureopean type W.C. material of approved make and quality all as per instructions of Engineer - in - charge. 1.00 Each 0.00

48 Providing and fixing white vitreous china flat back urinal basin of 600x 330 x 315mm or nearest available size a with push cock, standard flush pipe and C.P. brass spreaders with brass unions and G.I clampscomplete, including fittings and brackets, cutting and making good the walls and floors wherever required 9500*1.1+107.2+112.8 2.00 Each 0.00

49 Providing and fixing 15mm C.P. brass angle valve for various points of approved quality conforming to IS:8931 : etc., all complete as directed by the Engineer-in-Charge 7.00 Each 0.00

50 Providing, fixing, testing and commissioning trap (floor trap) of approved make with 100 mm inlet and 75 mm outlet of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors , connection with PVC soil / waste pipe, necessary 150 mm thick cement concrete (1:2:4) for embedding the trap,etc.,all complete as directed by the Engineer-in-Charge. 4.00 Each 0.00

51 Constructing masonry Chamber (60x60x75cm) inside or outside (or approx. size as per site condition) , in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size ) , i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design : 18.33.1 With common burnt clay F.P.S.(non modular) bricks of class designation 7.5. complete as per direction of Engineer-in-charge. 4.00 Each 0.00

52 Providing and fixing Concealed Chlorinated Polyvinyl Chloride (CPVC) pipes of approved brand, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, fixing the pipe with clamps at 1.00 m spacing, necessary reducers,unions,collars,bends, tank adaptors etc. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints and making good the walls etc as per direction of Engineer in Charge.

a)25 mm dia 24.00 RM 0.00

b)20 mm dia 24.00 RM 0.00

53 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge : External work

a)50 mm dia 24.00 RM 0.00

54 Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :

a)50mm nominal dia 2.00 Each 0.00

b)25mm nominal dia 3.00 Each 0.00

55 Providing and fixing PTMT soap Dish Holder having length of 138mm,breadth 102mm, height of 75mm with concealed fitting arrangements,weighing not less than 106 gms(or nearest availabe size and weight). 1.00 Each 0.00

56 Providing and fixing C.P. brass long/pillar body bib cock of 15 mm nominal bore, approved quality conforming to IS standards and weighing not less than 690 gms. 5.00 Each 0.00

57 Dismantling of old S.W. pipes of 100mm diameter including breaking of joints and bed concrete stacking of useful materials near the site within 50 m lead and disposal of unserviceable materials into municipal dumps and making temporary arrangements to protect/countinue ongoing service lines of other floors 10.00 RM 0.00

58 Dismantling Asbestos cement sheet of roofing including ridges, hips, valleys and gutters etc., and stacking the material within 50 metres lead of: 15.00 Sqm 0.00

59 Providing and fixing precoated galvanised iron profile sheets (size shape and pitch of corrugation as approved by engineer in charge) of total coated thickness 0.50mm (base metal of minimum 0.45mm thicknes with total coating thickness of 0.05mm) with zink coating 120grms /sqm as per IS:277,in 240mpa steel grade ,5-7micron apoxy primer on both side of the sheet and polister top coat 15-18 microns. Sheets should have protective guard film of 25micron minimum to avoid scratches during transportation and should be supply in single length upto 12meter or as desired by engineer-in-charge.The sheet shalllbe fixed using self drilling /selftapping screws of size (5.5*55mm) EPDM seal,complete upto any peach in horizontal bar verticala are curved surfaces, including the cost of purlins, rafters and trusess and including cutting to size nd shape wherever required. 345.00 Sqm 0.00

60 Providing and laying Sadarahalli 65mm to 70mm thick fine dressed stone flooring over 20 mm (average) thick base of cement mortar 1:5 (1 cement : 5 coarse sand) with joints finished flush. c. all, complete as per instructions of Engineer Incharge. 155.00 Sqm 0.00

61 Supplying, laying, testing and commissioning the 165mm dia PVC pipes of 6 kg/cm² SWR grade and of approved make with rubber ring joints conforming to IS 5382, jointed together with solvent, in walls, trenches and floors, including all necessary fittings & specials, bends, branches, sockets, pipe cutting and wastages, cutting and making good sealing the gaps with cement mortar and making in water tight etc., all complete as directed by the Engineer-in-Charge 30.00 Metre 0.00

62 Refixing existing stone slab flooring laid in over 20 mm (average) thick base of cement mortar 1:5 (1 cement : 5 coarse sand) with joints finished flush. c. all, complete as per instructions of Engineer Incharge. 70.00 Sqm 0.00

63 Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. 2.00 Nos 0.00

64 Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms. 1.00 Nos 0.00

Sub-Total of Part 'I' - Civil Works (Excluding GST) 0.00

Part 'II' - Electrical works

1 Supply, installation, testing & commissioning of Main LT Panel (PTTA) Indoor type for Executive Canteen 1.00 Each 0.00

Design, fabrication, supply, installation, testing and commissioning of cubicle type Indoor LT Panel with front lockable door arrangement, suitable to be mounted on the existing brick pedestal/cable duct using M.S channel(to be included) frame work, with cable entry from bottom/top with removable gland plates with required knock-outs, panel fabricated out of CRCA sheet steel folded and braced as necessary to provide a rigid support for all components, totally enclosed, dust and vermin proof and degree of protection shall not be less than IP-54, multi-tier cubicle type formation with front hinged lockable doors for the individual feeders/compartments, preparation of surface and treatment by seven tank process, powder coated with approved colour for not less than 50 microns and all doors and covers shall be fully gasketed using good quality EPDM gasket and/or rubber strips and ensure good lockable, durable door opening & closing mechanism, suitable meshed ventilator louvers with suitable cover,canopy type covering and Aluminium bus bars for three phases and neutral, bus bar insulators, heat shrinkable PVC sleeves etc., with necessary interconnections as specified in Technical specifications for electrical & mechanical works, comprising of following switchgear and accessories complete in all respects and as directed by Engineer-in-charge.

Note:-1) Current density shall not exceed 0.8A/sq.mm for Aluminium bus bars in LT Panel

2)All MCCBs in the LT panels shall be adjustable with thermal settings(80% to 100%), overload and short circuit releases including door interlocking device, front operating handle complete,ON and OFF indication of LED module etc. complete in all respects.

3)The operating height of the Panel shall not exceed 2.1 mtr. from FFL.

i) 1No-400 A, TP+NL MCCB 36 KA with TM based with O/L, S/C Releases with RHOM+Spreaders+Aux 1 C/O+TAC 1 C/O

ii) Lot - 600A TP + 300 N, 415V, short circuit rated 36KA for 1sec, Aluminium bus bars with busbar insulators, heat shrinkable PVC sleeves etc.

iii) 1No- Multi function meter (MFM/MDM) suitable for 3ph, 4 wire, 240V(L-N), 5A, CL-1, RS 485 Port Digital MFM/MDM of EM6400NG of Schneider or any equivalent make meeting technical specification of above MFM complete in all respect.

iv) 1Set of - 400/5A current transformers of class 1 and 15VA burden for metering.

v) 1No- (0-500V) range 96x96mm flush type voltmeter with RYB selector switch

vi) 1No 16A 415V gr TP 50KA MPCB of for tapping power for metering and control circuit

vii) 1Set - RYB indicating lamps of LED module with 6A SP MCB.

viii) 1Set- 6A, MCB for the protection of measuring instruments.

i) 1 No.- 250A TP+NL, MCCB TM based with O/L, S/C Releases with RHOM - 36kA

ii) 3 Nos.- 160A TP+NL, MCCB TM based with O/L, S/C Releases with RHOM - 36kA

iii) 3 Nos.- 125A TP+NL, MCCB TM based with O/L, S/C Releases with RHOM - 36kA

iv) 4 Nos.- 100A TP+NL, MCCB TM based with O/L, S/C Releases with RHOM - 36kA

v) 7 Nos.- 63A TP+NL, MCCB TM based with O/L, S/C Releases with RHOM - 25kA

vi) 3 Nos.- 32 A 4Pole, MCB "C" Curve - 10 KA

2 SUPPLY AND LAYING OF LT CABLES

Supply, testing & commissioning of following size XLPE insulated Aluminium (Al) conductor 1.1 KV grade confirming to IS: 7098 ( part-I)/1998 with upto date amendment earthed Armoured (Arm) U.G cables and as per technical specification including stacking at site, proper storage complete etc. as required. (Note:- Laying, Excavation, sand & Brick Protection, concrete cutting, reconcreting, casing pipes will be measured separately.)

2.1 3.5 CX120 Sqmm Aluminium armoured conductor 90.00 Mtr 0.00

2.2 3.5 CX95 Sqmm Aluminium armoured conductor 100.00 Mtr 0.00

2.3 3.5 CX70 Sqmm Aluminium armoured conductor 100.00 Mtr 0.00

2.4 3.5 CX25 Sqmm Aluminium armoured conductor 250.00 Mtr 0.00

2.5 4 CX16 Sqmm Aluminium armoured conductor 410.00 Mtr 0.00

2.6 Laying in the already excavated cable trench/cable tray/fixing on wall/duct wall with necessary M.S clamps / encasing in pipes etc., testing & commissioning of following size XLPE insulated Aluminium (Al) conductor U.G cables and as per technical specification including stacking at site, proper storage complete etc. as required. (Note:- Excavation, sand & Brick Protection, concrete cutting, reconcreting, casing pipes will be measured separately.)

2.6.1 3.5 CX120 Sqmm Aluminium armoured conductor 90.00 Mtr 0.00

2.6.2 3.5 CX95 Sqmm Aluminium armoured conductor 100.00 Mtr 0.00

2.6.3 3.5 CX70 Sqmm Aluminium armoured conductor 100.00 Mtr 0.00

2.6.4 3.5 CX25 Sqmm Aluminium armoured conductor 250.00 Mtr 0.00

2.6.5 4 CX16 Sqmm Aluminium armoured conductor 410.00 Mtr 0.00

3 CABLE END TERMINATIONS

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.

3.1 3.5 CX120 Sqmm Aluminium armoured conductor 6.00 Each 0.00

3.2 3.5 CX95 Sqmm Aluminium armoured conductor 2.00 Each 0.00

3.3 3.5 CX70 Sqmm Aluminium armoured conductor 2.00 Each 0.00

3.4 3.5 CX25 Sqmm Aluminium armoured conductor 6.00 Each 0.00

3.5 4 CX16 Sqmm Aluminium armoured conductor 12.00 Each 0.00

4 Supply, fixing on wall/grouted to the floor 600/1000mm above floor level, using suitable angle iron frame work, testing and commissioning of the 160A, 415V Gr, TPN powder coated, Switch disconnector fuse unit with equal rating DIN type HRC fuses, front operating handle,ON and OFF indication using LED module etc., enclosed in sheet steel enclosure, including suitable cable end box(incoming/outgoing) wherever necessary complete in all respects and as directed by Engineer-in-charge. 3.00 Each 0.00

5 Supply, fixing, testing & commissioning of the following factory built powder coated Double door MCB/MCCB DB of any approved make fabricated out of M.S. sheet steel enclosure & necessary cutouts for operating the MCB knobs & comprising of 200 amps tinned copper busbars & earthing bus with tapped holes including internal wiring with stranded copper PVC wires or suitable size copper strips etc. & fixing the DB in flush with wall/ on wall as per site requirement with necessary M.S. angle supports, chipping the wall and replastering to smooth finish etc., wherever required as per site condition, complete in all respects, as directed by Engineer-in-charge and comprising the following as detailed below:

5.1 8 way (4+24) Double door Vertical TPN MCCB DB 1.00 Each 0.00

5.2 12 way (4+36) Double door Vertical TPN MCCB DB 1.00 Each 0.00

5.3a 125A, TP+NL MCCB 25 KA breaking capacity as Incomer 2.00 Each 0.00

5.3b 63 amps. ratings, TP MCB, "C" curve, 10 KA breaking capacity 3.00 Each 0.00

5.3c 32 amps. ratings, TP MCB, "C" curve, 10 KA breaking capacity. 1.00 Each 0.00

5.3d 16 amps. ratings, TP MCB, "C" curve, 10 KA breaking capacity. 8.00 Each 0.00

5.3e 6-32 amps. ratings, SP MCB, "C" curve, 10 KA breaking capacity. 78.00 Each 0.00

6 Supply, fixing, testing & commissioning of the following factory built powder coated Double door MCB/MCCB DB of any approved make fabricated out of M.S. sheet steel enclosure & necessary cutouts for operating the MCB knobs & comprising of 200 amps tinned copper busbars & earthing bus with tapped holes including internal wiring with stranded copper PVC wires or suitable size copper strips etc. & fixing the DB in flush with wall/ on wall as per site requirement with necessary M.S. angle supports, chipping the wall and replastering to smooth finish etc., wherever required as per site condition, complete in all respects, as directed by Engineer-in-charge and comprising the following as detailed below:

6.1 4 Way, (4+12), Double door Horizontal MCB DB 8.00 Each 0.00

6.2 6 Way, (4+18), Double door Horizontal MCB DB 1.00 Each 0.00

6.3 63 amps. ratings, 4P MCB, "C" curve, 10 KA breaking capacity. 7.00 Each 0.00

6.4 32 amps. ratings, TPN MCB, "C" curve, 10 KA breaking capacity. 9.00 Each 0.00

6.5 16 amps. ratings, TPN MCB, "C" curve, 10 KA breaking capacity. 1.00 Each 0.00

7 Supply & fixing in the existing distribution board of Modular digital timer switch for Building light control of Legrand Alpha Rex 3 D21 or equivalent approved make with one channel daily cycle unit suitable for daily programming to switch ON & OFF and operate on 230V single phase supply including supply & fixing of suitable 3 Phase output contactor and as directed by Engineer -in-charge.. 1.00 Each 0.00

8 Supplying and fixing of the following size Hot dip galvanised Perforated type cable tray, steel: As per IS:2062 / 1079, Galvanising : As per IS: 2629 / 4759 including all accessories like base slotted angle , horizontal elbow, horizontal tee, horizontal cross, horizontal reducer, vertical elbow up, inside, vertical elbow down, outside, coupler plate, fasteners etc.

8.1 150mm width x 50mm depth x 1.6mm thickness 100.00 Mtr 0.00

8.2 300mm width x 50mm depth x 1.6mm thickness 50.00 Mtr 0.00

9 Design, Fabrication, Supply and fixing/grouting in wall/ceiling of suitable size MS angle iron supports/ flat/ brackets for cable tray supports, as per site requirement and painting the same with two coats of synthetic enamel paint over a coat of zinc chromite primer complete in all respects and as directed by EIC/OIC. 400.00 Kg 0.00

10.1 Supply & providing GI earth stations using 600 x 600x 6.3 mm thick G.I plate electrode at 2.5 mtr. below the ground level with 20mm dia class B G.I pipe for watering, G.I funnel etc. & Cement concrete base of minimum size 750x750x100mm thick shall be provided using 1:2:6 CC after necessary excavation, refilling of soil, consolidating, ramming, leveling of soil etc. and providing cement concrete chamber of inside dimension 300x300x300mm with a wall thickness of 120mm using 1:2:6 CC above the base concrete including providing 50mm thick RCC cover including required salt & charcoal, 2 runs of 50x6 mm G.I strip from plate electrode upto top of the chamber etc. as per technical specification enclosed with the tender & as per IS 3043 complete in all respects. 7.00 Set 0.00

10.2 Supplying & laying 25 mm X 5 mm GI strip at 0.50 metre below ground as strip earth electrode, including connection/terminating with G.I nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of GI nut bolt & spring washer spaced at 50mm) 300.00 Mtr 0.00

11 Supply & fixing on wall using suitable fixing arrangement of 5 pin 63A, 415V, Flame proof socket outlet including 63A flame proof 5pin top & cable end termination box for complete in all respects including necessary interconnections complete in all respects as directed by Engineer-in-charge. 2.00 Each 0.00

12 Supply & fixing on wall using suitable fixing arrangement of 3 Phase 415V, Flame proof DOL Starter for 3HP Motor complete in all respects including necessary interconnections complete in all respects as directed by Engineer-in-charge. 1.00 Each 0.00

13 Supply & fixing on wall using suitable fixing arrangement 16A, 250V, 3Pin Flame proof, wall mounting switch, socket & plug combined in LM6 cable termination box complete in all respects including necessary interconnections. 3.00 Each 0.00

14 Supply,fixing, testing and commissioning of Direct-on-Line Starters in Sheet-Steel Enclosure Type (Motor Rating AC-3 Duty, 415V, 50Hz, 3-Ph) starter suitable for 2 HP motor or as required for pump motor. The starter shall be with sufficient auxiliary contacts for remote ON/OFF i, suitable rating bi-metallic thermal overload relay, ON/OFF push buttons suitably wired and interconnected with 2.5 Sq.mm single stranded PVC copper wires, etc. complete in all respects as directed by Engineer-in-charge. 1.00 Each 0.00

15 Supply,fixing, testing and commissioning of Direct-on-Line Starters in Sheet-Steel Enclosure Type (Motor Rating AC-3 Duty, 415V, 50Hz, 3-Ph) starter suitable for 3 HP motor or as required for pump motor. The starter shall be with sufficient auxiliary contacts for remote ON/OFF i, suitable rating bi-metallic thermal overload relay, ON/OFF push buttons suitably wired and interconnected with 2.5 Sq.mm single stranded PVC copper wires, etc. complete in all respects as directed by Engineer-in-charge. 8.00 Each 0.00

16 Supply,fixing, testing and commissioning of Direct-on-Line Starters in Sheet-Steel Enclosure Type (Motor Rating AC-3 Duty, 415V, 50Hz, 3-Ph) starter suitable for 5 HP motor or as required for pump motor. The starter shall be with sufficient auxiliary contacts for remote ON/OFF i, suitable rating bi-metallic thermal overload relay, ON/OFF push buttons suitably wired and interconnected with 2.5/4 Sq.mm single stranded PVC copper wires, etc. complete in all respects as directed by Engineer-in-charge. 2.00 Each 0.00

17 Supply,fixing, testing and commissioning of Direct-on-Line Starters in Sheet-Steel Enclosure Type (Motor Rating AC-3 Duty, 415V, 50Hz, 3-Ph) starter suitable for 7.5 HP motor or as required for pump motor. The starter shall be with sufficient auxiliary contacts for remote ON/OFF i, suitable rating bi-metallic thermal overload relay, ON/OFF push buttons suitably wired and interconnected with 2.5 Sq.mm single stranded PVC copper wires, etc. complete in all respects as directed by Engineer-in-charge. 1.00 Each 0.00

18 Supply,fixing, testing and commissioning of Fully automatic Star Delta Starter in Sheet-Steel Enclosure Type (Motor Rating AC-3 Duty, 415V, 50Hz, 3-Ph) starter suitable for 7.5HP motor or as required for pump motor. The starter shall be with sufficient auxiliary contacts for remote ON/OFF i, suitable rating bi-metallic thermal overload relay, ON/OFF push buttons suitably wired and interconnected with 4/6 Sq.mm single stranded PVC copper wires, etc. complete in all respects as directed by Engineer-in-charge. 1.00 Each 0.00

19 Supply & fixing of 5 in 1 PVC Box incluing 6pin 16/20A, 230V, Socket outlet, switch, Indicator complete in all respects as directed by Engineer-in-charge. 8.00 Each 0.00

20 Supplying and fixing suitable size GI Box /PVC box as per site requirement with modular plate and cover on front on surface or in recess, including providing and fixing 6 pin 5/6A & 15/16A modular socket outlet and 15/16 A modular switch, connections etc., as required. 10.00 Each 0.00

21 Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required.

21.1 Supply and fixing of 2 Module, GI box alongwith modular base & cover plate for fixing modular switches/sockets in recess etc. as required. 4.00 Each 0.00

21.2 Supply & fixing of modular 3 Pin 5/6A socket outlet on exisitng modular plate & switch box including connections 4.00 Each 0.00

22 Supplying and Fixing of 30/32A, 415V, TPN Industrial type socket outlet with 4 pole and earth, Metal enclosed plug top alongwith 30/32A "C" curve, TPMCB in sheet steel enclosure on surface or in recess, with chained metal cover for the socket outlet and complete with connections, testing and commissioning etc. as required 1.00 Each 0.00

23 Wiring for circuit / submain wirng alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed steel conduit as required

23.1 4 x 10 Sqmm + 2 x 6 Sqmm earth wire 100.00 Mtr 0.00

23.2 4 x 6 Sqmm + 2 x 6 Sqmm earth wire 90.00 Mtr 0.00

23.3 4 x 4 Sqmm + 2 x 4 Sqmm earth wire 400.00 Mtr 0.00

23.4 4 x 2.5 Sqmm + 2 x 2.5 Sqmm earth wire 400.00 Mtr 0.00

23.5 2 x 6 Sqmm + 1 x 6 Sqmm earth wire 125.00 Mtr 0.00

23.6 2 x 4 Sqmm + 1 x 4 Sqmm earth wire 400.00 Mtr 0.00

23.7 2 x 2.5 Sqmm + 1 x 2.5 Sqmm earth wire 1850.00 Mtr 0.00

23.8.1 Supply & drawing/laying of 4C X 6 Sqmm PVC insulated 1100V gr. flexible multi stranded Copper cable with ISI mark using suitable copper lugs including necessary interconnections, clamps & hardwares complete as directed by Engineer -in-charge. 200.00 Mtr 0.00

23.8.2 Supply & drawing/laying of 4C X 4 Sqmm PVC insulated 1100V gr. flexible multi stranded Copper cable with ISI mark using suitable copper lugs including necessary interconnections, clamps & hardwares complete as directed by Engineer -in-charge. 25.00 Mtr 0.00

23.9 Supplying and fixing of following sizes of steel conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required.

a) Supplying and fixing of 32mm steel conduit 200.00 Mtr 0.00

b) Supplying and fixing of 25mm steel conduit 25.00 Mtr 0.00

24 Wiring in Steel Conduit & PVC Conduit

24.1 Wiring for light point / fan point / exhaust fan point / call bell point with 1.5Sqmm FRLC PVC insulated conductor single core cable in surface/recessed steel conduit with Modular switch, modular plate, suitable GI box and earthing the point with 1.5Sqmm FRLS PVC insulated copper conductor single core cable etc. as required. 20.00 Pt 0.00

24.2 Wiring for light point / fan point / exhaust fan point / call bell point with 1.5Sqmm FRLC PVC insulated conductor single core cable in surface/recessed medium class PVC conduit with Modular switch, modular plate, suitable GI box and earthing the point with 1.5Sqmm FRLS PVC insulated copper conductor single core cable etc. as required. 50.00 Pt 0.00

25 Supply , fixing, testing and commissioning of LED FLAMEPROOF batten suitable for 1x16/20W T8 Tube light housing Made of Die cast Aluminum alloy with corrosion resistant powder coated, with high efficiency acrylic wide diffuser, with wide operating voltage range, Power factor > 0.9, The lumens efficacy >90lm/watt. Operating on single phase 230V voltage 50 Hz AC supply with voltage range 140-270V including necessary interconnections and supply of 1 No of 18/20W T8 LED Tube, complete in all respects and as directed by engineer-in-chage. Make & model: The LED tube & batten shall be of CROMPTON-EXTN1LT8-16/20/Equivalent model of approved make luminaries which meets the above technical specification. complete in all respect and as directed by Engineer-in-charge. 20.00 Each 0.00

26 Supply and fixing on existing wall / ceiling, testing & commissioning of surface mounting, Box type 1X18W/20W T8 LED Tube light (four feet) Luminaries with minimum lumens output Efficacy of minimum100 lm/W., comprising of white powder coated CRCA sheet steel housing, operating on single phase 230V 50Hz AC supply, built-in electronic driver, LM 79 certification for luminaire. Other standard accessories including necessary inter-connections and supply of 1 No of 18/20W T8 LED Tube, complete in all respects and as directed by engineer-in-chage. Make & model: The LED tube & batten shall be of CROMPTON-IGP161LT8-16.1XT8+LT8-20-865/Equivalent model of approved make luminaries which meets the above technical specification. complete in all respect and as directed by Engineer-in-charge. 15.00 Each 0.00

27 Supply & fixing on the building at a height of 4-5mtr approx. including supply and fixing GI pipe bracket made out of 40mm dia class B GI pipe of 1.5Mtrs long bent to shape with necessary fixing hardwares etc., to fix on building and testing & commissioning of 24-30W/ ≥ 2500 lumens output LED light fixture with necessary interconnections consisting of pressure die cast aluminum housing, optical cover made out of heat resistance toughened clear glass / polycarbonate with IP65, luminous efficiency ≥ 100lm/w at lumiare level, operating on single phase 230V 50Hz AC supply, efficient heat sink, colour temperature shall be >5700K, suitable optics for maximizing the spread(120 degrees approx) complete in all respects and as directed by engineer-in-chage. The luminaire shall have specific lens for optical dispersion including control gear and power factor of control gear shall be >0.9. LM 79 certification for luminare & LM80 certificate for LED shall be produced. Any approved make fitting meeting the above technical specification has to be supplied. LED used in the fittings shall be of approved make as per List of approved makes in tender documents. 10.00 Each 0.00

28 Supply & fixing on existing MS hook 1200mm sweep, Five star rated with brushless direct current motor(BLDC) Ceiling fans complete with blades, down rods, and accessories, 230V single phase 50Hz AC supply. Minimum air delivery 210cu.m/min with service value 6.00 BEE , erected in position with necessary flexible copper leads of required colour and with canopy, down rod 300mm to 300mm length as per site requirement , necessary rubber bushings, clamps nuts,bolts etc., complete in all respects and as directed by Engineer-in-charge. 5.00 Each 0.00

29 Supply & fixing of extra conduit down road

29.1 Supplying and fixing extra conduit down rod of 50 cm length G.I. pipe 15 mm dia, heavy gauge including painting etc. As required. 75.00 Each 0.00

30.1 Dismantling 1.00 LS 0.00

Disconnecting/dismantling & removal of the following items as-is-basis without any damage and handing over the same to the place as shown by Engineer-in-charge/Plant Maintenance department of ARDC( not more than 1KM) including loading, transportation, unloading etc., complete in all respects and as directed by the engineer-in-charge.

a) Dismantling of existing OLD Panel board near stair case comprising of 200A SFU incomer and outgoings. 32A & 63A MCB's-6Nos.

b) Dismantling of existing 400A MCCB enclosure with bus bar box-1 Set.

c) Dismantling of Switch boards including wiring-6 Sets

d) Dismantling of 100A TPN Switch - 6 Nos

e) Dismantling of Distribution boards - 5 Nos

f) Dismantling of existing light fittings including wiring - 10 Nos

g) Dismantling, removing, re-routing & re-connecting of existing LT cables 3.5CX185-300sqmm LT Cables-20mtrs.

h) Dismantling & removing of existing LT cables 3.5CX25-95sqmm LT Cables-250mtrs.

Note: 1. The quantity indicated are only approximate. 2. The tenderers are requested to visit the site and acquaint themselves with the present conditon and quote accordingly. 3. No extra claims will be entertained at a later stage.

30.2 Demolishing cement concrete manually/ by mechanical means including disposal of material as per direction of Engineer - in - charge. 1.00 Cumtr 0.00

e) Sub-Total of Part 'II' - Electrical (Excluding GST) 0.00

f) Total of Part 'I' + 'II' (Excluding GST) 0.00

g) Add 18% GST 0.00

h) Grand Total (Including GST) 0.00

HINDUSTAN AERONAUTICS LIMITED

Facilities Management Division

Pre-Qulification Profile (To Be uploaded along with Part A)

Tender Ref No. or Contract No.: HAL/FMD/R-142/24-25

Name of Work: Carrying out Civil and Electrical Works pertaining to Renovation of Kitchen Area of Executive Canteen at ARDC, HAL [DC].

Estimated Amount in Rs.: 8770000

Tender Notice Date : 20.02.2025

PROVISIONAL GST ID NO. for HAL 29AAACH3641R1Z3

Sl.No Description Details Enclosed / Not Enclosed Remarks

1 Name of the Individual / Firm / Company: * Mandatory Please Enter Name of the Individual/firm/company

2 Type of ownership PlsEnter Type of Ownership

If Other, please specify

3 Details of Constitution or Legal Status such as certificate of incorporation, shops and establishments, Contractor registration No etc., Pls enter Details of Constitution

4 Address for correspondence: Pls Enter Address

5 (a) PAN No.: Pls Enter Pan NO

5 (b) Service Tax Registration No

5 (c ) Goods and Service Tax ID No.

6 Contact details

Contact person name Please Enter Contact person Name

Mobile No. Pls Enter Mobile No

Ph. No. with STD code

FAX No. with STD code 1 #N/A

7 Registered Contractor

If Registered Contractor with HAL Yes/ No Related Document to be Uploaded to eProcurement Portal * Category: E= 75 Lakhs - Lessthan= 100Lakhs F= 50Lakhs - Lessthan 75 Lakhs G = 25Lakhs - Lessthan 50 Lakhs H = 10Lakhs - Lessthan 25 Lakhs I = 5Lakhs - Lessthan 10 Lakhs J = 2Lakhs - Lessthan 5 Lakhs K = Lessthan 2Lakhs 0 7 E 1

Registration No. 199999 7 F 2

Category 200000 6 G 3

PEMD Amount ( If paid ) 499999 6 H 4

8 I.T Returns for past 03 years 999999 5 J 6

2024-25 Pls Select 'Yes' ' No' for IT Return for All Three years 1000000 4 K 7

9 Average annual financial turn over during the last 3 years, ending 31st March 2024 of the previous financial year [ should not be less than 30% of Amount put to tender] 4999999 3

YEAR TURN OVER IN Rs. Enclosed / Not Enclosed REMARKS 5000000 2

2023- 2024 Rs. Pls Enter Turn over in Rupees for all the 3 years 7499999 2

Average annual Financial turn over 0.00 2631000.00

Avg Annual Turnover criteria is not met 10000000 1

10 ESI & PF Nos with proof Nos Enclosed / Not Enclosed

ESI Registration No/. with proof if any Remarks if any

PF Registration No. with proof if any

11 Bank(s) details: [Copy of the cheque leaf to be uploaded]

Bank Account No. Related Document to be Uploaded to eProcurement Portal (Note Canceled cheque leaf to be uploaded)

Name of the Bank

Type of Account

12 Latest Bankers Solvency Certificate from Nationalized/ scheduled Bank issued NOT before 12 months from the last date of Tender submission solvency cal

Name of Bank & Branch Pls Enter Details to 'Name of the Bank' , 'Date of Issue','Value in Rs #REF! 28-Jun 0 40000

Date of Issue 200000 40000

Value in Rs. 200001 150000

Solvency value is NOT as per NIT

13 Experience of having successfully completed similar works during last 7 years ending last day of previous month. [Latest work experience certificate may be uploaded] (i) THREE similar completed works each costing not less than the amount equal to 40% of the estimated cost. (ii) TWO similar completed works each costing not less than the amount equal to 50% of the estimated cost. (iii) ONE similar completed work each costing not less than the amount equal to 80% of Amount put to the tender. 3508000 500001 250000

Completed similar works during last 7 years Pls Select %of similar works completed during last 7 years 1000000 250000

Work NoI Type of Work: [ Incase of private works the same shall be supported with TDS certificate] Related Document to be Uploaded to eProcurement Portal 1000001 500000

Brief Description of Work: Please enter Details for Work No 1 2000000 500000

Completed value of Work in Rs. 2000001 1000000

Date of Commencement of Work 4000000 1000000

Date of Actual Completion of Work: 4000001 2000000

Work No II Type of Work: [ Incase of private works the same shall be supported with TDS certificate] Related Document to be Uploaded to eProcurement Portal 10000000 2000000

Brief Description of Work: Pls Enter Details for Work No II

Completed value of Work in Rs.

Date of Commencement of Work:

Date of Actual Completion of Work: work done

Work No III Type of Work: [ Incase of private works the same shall be supported with TDS certificate] Related Document to be Uploaded to eProcurement Portal #REF! 2555

Brief Description of Work: Pls Enter Details for Work No III #REF!

Completed value of Work in Rs.

Date of Commencement of Work:

Date of Actual Completion of Work:

14 Details of person holding the power of Attorney (If different from contact person)

Name Related Document to be Uploaded to eProcurement Portal

Mobile No. Pls Enter Details for Person holding Power of Attorney

Ph. No. with STD code

FAX No. with STD code

15 DECLARATION I

The document being viewed / downloaded from the website and having read & understood all the contents of the tender document mentioned under terms and conditions including price bid do hereby accept all the terms and conditions laid down in the said Tender document and will abide by the same on acceptance and ward of work.

16 DECLARATION II

I/We declare and confirm that - 1. All information and attachments submitted along with this offer are true and correct. 2. I/We are aware that any false information provided herein will result in the rejection of my offer. 3. I/We shall not make refund claims of expenditure incurred in processing this offer. 4. I / We aware that document sought only be uploaded for evaluation of offer. Pls Accept the Delaration II