Toilet Block Renewal , Water Supply Arrangements and Providing Interlocking Paver Block Pavement for Kariya Mandapam near Muthumandapam in Ward No.17, Zone-IV in Vellore Corporation

Brickwork in CM 1:5 (One Cement & Five sand) using II class ground moulded bricks of size 9" x 43/8" x 2 3/4" including finishing, curing etc., complete complying with standard specification

Ground floor

Supplying and erecting Centering for sides and soffits including supports and shuttering upto 3m high for plane surface such as side slabs of RCC boxing and similar vertical RCC slab etc., withall cross bracings using mild steel sheets of size 90 x 60cm and 10 gauge stiffened with welded mild steel angles of size 25 x 25 x 3mm for boarding laid over Oak (country wood) joists of size 10 x 6.5 cm spaced at about 90 cm centre to centre and supported by casuarina props of 10 to 13 cm dia spaced at 75 cm centre etc., complete

Beams and slabs

Suppling and fabricating and placing in position MS(or) R.T.S. bar for Reinforcement to all RCC works as per the design given including cost ofsteel and binding wire also in all floors.

Reinforced Cement Concrete 1:1.5:3 (One Cement, One and half sand & Three coarse aggregate) using 20mm gauge hand broken/ and broken granite stone for all RCCitemsof works excluding centering shuttering and cost of reinforcement but including curing etc.,complete and alsoincluding fixingfan clamps and fixtures in rccworkswherever necessary as directed by departmentalofficer etc., complete.

Ground Floor

Plastering with cement mortar 1:3, 10mm thick in all floors including cost and conveyance of all materilas to site and labour charges etc,complete as per standard specifications (S.I.306)

Plastering with cement mortar 1:5 mix, 12mm thick in all floors including cost and conveyance of all materilas to site and labour charges etc,complete as per standard specifications (S.I.306)

Dadooing walls withGlazed tiles of sizes 305mm X 200mm X 6mm size of approved make and quality and colour Set in cement mortar 1:2 (One part of Cement and two part of Plastering Sand (P- Sand)) over 10 mm base layer plastering and pointing with white cement neatly as directed.

Manufacturing supplying and fixing ofMILD STEEL DOOR made out of 50 x 50 x 6 mm M.S angle for outer frame,35 X 35 X 5mm M.S.Angle for outer frame of shutter. The entire shutter area shall be covered with CRC sheets (18 G) with 5Nos, of stiffners using M.S.Flats of size 25 X 6mm at equal intervals horizontally. The corners of the frames and shutter with CRC sheets shall be welded by adopting flash butt welding or any other suitable method. Provision towards 3Nos, of Hinges incase of single shutters / 6Nos,of Hinges incase ofDouble shutters of 125 X 31 X 1.25mm size placed at appropriate intervals and provisions shall be made for Tower bolts 2Nos, Aldrop 1No. The frame shall be provided with 6Nos,of Hold fast of 200mm length using 50 X 6mm M.S.Flat. The entire frame and shutter shall be provided with one coat of red oxide primer including cost of hold fasts,hinges, locking arrangements, handles wind appliences etc., complete and as directed by the departemental officers.

Finishing the top of Sloped Roof, Sunshadewith DecorativePressed Tiles of approved Quality laid in Cement mortar 1:3 (One part of Cement and Three part of Plastering Sand (P- Sand)), 20mm thick mixed with WPC at 2% by weight of Cement used and toppointedwith same red oxide mixed mortaretc., complete complying with standard specification

Supply and Fixing of R.C.C.Jollyin M20 Concrete using 20mm gauge hard broken granite stone jelly and river sand excluding cost of reinforcement but includingcharges,fabrication chargescuring neat finishing and labour charges for fixing the jolly in position with standard spefication

Supplying, laying and jointing PVC pipes (having working pressure 10 kg. / sq.cm) of approved quality and best variety conforming to BIS of the following dia including cutting, threading and fixing PVC specials using PVC adhesives (but excluding cost of such specials) and fixing into wall with teak wood plugs, PVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges, etc., complete complying with standard specifications.The PVC pipes shall be got approved by Executive Engineer before use on works.

25mm dia

Supplying PVC Specials (with working pressure 10 kg. / Sq.cm) in water supply arrangements (both in internal and external water supply arrangements

Coupler

25 mm Dia (M-0882 - PWD SoR 25-26)

Elbow

25 mm Dia (M-0888 - PWD SoR 25-26)

25 mm Dia (M-0894 - PWD SoR 25-26)

25 mm Dia (M-0900 - PWD SoR 25-26)

End Cap

25 mm Dia (M-0906 - PWD SoR 25-26)

Reducer

20 mm x 15 mm (M-0910 - PWD SoR 25-26)

25 mm x 20 mm (M-0911 - PWD SoR 25-26)

Reducer Tee

20 mm x 15 mm (M-0915 - PWD SoR 25-26)

25 mm x 20 mm (M-0916 - PWD SoR 25-26)

Reducer Elbow

20 mm x 15 mm (M-0920 - PWD SoR 25-26)

25 mm x 20 mm (M-0921 - PWD SoR 25-26)

PVC Screw Down Tap Heavy Type

20 mm Dia (M-0510 - PWD SoR 25-26)

Supply and delivery of 1000 litres PVC Tank as per IS 1201/ 1996 including loading , unloading, transportation, and labour charges for fixing the GI specials for Pipe Connections including cutting threding and fixing etc etc., complete as per standard specifications WD-M1418 -25-26

Supplying and fixing in position PVC specials of the following dia and types of approved quality confirming to BIS and providing leak proof joints including fixing to the walls and giving connection to the PVC soil stacks, dismantling the masonry or RCC works and re-doing the dismantled portion to original condition etc., complete complying with standard specifications. (The PVC specials should be got approved by the Executive Engineer before use on works)

PVC Elbow

110 mm dia

75 mm dia

PVC Elbow with Door

110 mm dia

PVC Tee

110 mm dia

75 mm dia

PVC Tee with Single Door

110 mm dia

Supplying and fixing in position White / Colour Glazed Model Floor Mounted European Water Closet of best quality and approved make with 100mm “P” or “S” trap connecting with CI pipe of 100mm dia / PVC pipe of 110mm dia, double flapped rigid PVC black seat and seat cover with CP brass hinges including cost of white cement, cement for packing, spun yarn, teak wood plugs, brass screws, etc., including supplying and fixing 10 liters capacity PVC / 12.5 liters capacity porcelain low level flushing tank with a pair of CI brackets, etc., complete with all fittings, such as, 15mm brass ball valve with polythene float with brass handle, union coupling connected by means of 40mm white PVC flush hand using Indian adopter joint including all internal fittings, such as, 15mm bras connections, 15mm GM wheel valve, 15mm brass nipple (2 Nos.), 15mm nylon connection, TW plugs, screws and also giving necessary connection to the PVC pipe and painting the CI brackets with 2 coats of approved paint over one coat of red oxide primer, dismantling the masonry and re-doing the dismantled masonry to original condition, etc., complete complying with standard specifications. (The EWC and flushing tank with all accessories should be got approved by the Executive Engineer before use on works) Floor Fitting

Wiring with 2 x 1.5 sqmm (22 /0.3 ) PVC insulated single core unsheathed copper conductor cable of 900V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories inflush with wall with 3mm thick hylum sheet cover with TW switch box and 5A F.T. switch with continuous earth wire connection of 14 SWG TC wire for making good of the concealed portion with suitable colour for PVC concealed Light point/Fan point (For Electronic regulator) etc, complete as per standard specifications. SD18

Supply and fixing of Supply and fixing of WT bulk head fitting with guard suitable for 7 W / 9 W LED bulbincluding cost of all material charges and labour charges etc, complete as per standard specificationsSD 84

Supplying, fabricating, erecting structural steel work for roofing welded or bolted type using MS channels, angles, plates and round bars etc. conforming to IS specification including primer coating and enamal painting as per Design given by the departmental officers etc, complete as per standard specification

Painting two coats with ready mixed Plastic Emulsion Paint approved quality and colour over a priming coat, including thorough scrapping, clean removal of dirt, etc complete and including necessary plaster of paris, putty, wherever required etc, complete as per standard specification

Painting two coats with Ready Mixed Enamel Paint over the new iron works of approved quality and colour without priming coatincluding the cost all materials etc.,complete, in all floors.

Supplying and laying Rubberised interlocking Paver blockM40 grade Providing and laying of83mmthick high strength type conforming IS 15658-2006 of rubberized interlocking paver lock in size of minimum compressive strength of 40N/mm2 in uniform shape of approved make to be laid in flurring bone pattern with sand cushion below the uniform shap of approvednon skitting surface in the top and the rate including levelling the base preparation ofpavers as sub base, sand cushion 150mm thick layingout of pavement cut the pieces to fix the edge vibring the pavers,sweeping tranporting loading unloading of laying paver block as per standard specification,.

Please Enable Macros to View BoQ information