SPECIAL REPAIR TO CERTAIN SMQ BLOCKS AT 13 BRD UNDER GE (AF) GURGOAN NO 1

Amount

Demolition of Cement Concrete (un-reinforced) of any description, not exc. 150mm thickness (above or below Ground Level) and removing out side from MoD land complete all as specified and directed.

M&L for 15 mm thick rendering in CM 1:3 by on brick/concrete surfaces of sunken slab, mixed with liquid water proofing compound both floor and wall of sunken slab, the surface shall be cured and allow to dry, finished even and smooth without using extra cement complete all as specified and as directed by Engineer-in-Charge. Note :- Water proofing compound shall be measured and paid separately.

M&L for PCC 1:5:10 type E-2 (using 40mm graded stone aggregate) as in filling under floor/sunken slab complete all as specified and directed.

Cutting upto a depth of 2.5cm into concrete/Brick walls and trimming surface as required,girth exc. 30cm and Fixing of 25mm dia GI pipe (med gde) spout of length 45 cm with CM 1:3 as in sunken base complete all as specified and directed.

Dismantling of existing brick tiles in single layers on roof including grass, trees treating with chemical and cleaning the surface and removal out side of MoD land complete all as specified and as directed. Note :Taking down earthng strips and solar panel wires from roof and re-fixing on the same position after APP laying is deemed to be inclusive of rate quoted by the contractor.

Demolition of existing mud in roofs of any thickness including plastering and leeping (whether full thickness removed or only a part thereof) and removing of mud out side of MoD land, (up to 4th storey) all as specified and direction by Engr in charge.

M&L for Cutting out cracks 'V' section on existing roofs or terrace cleaning out and filling solidly with a hot mixture bitumen and clean dry sand 1:1 by weight complete all as specified and directed by Engr-in-Charge.

M&L providing cement concrete in roof or mud stops using type B-1, 1:2:4 (20mm graded aggregate) rounded or chamfered on edges or making slop on roof complete (up to 4th Storey) all as specified and as directed

M&L 25 mm, thick PCC 1:2:4 TYPE B-0 (using 12.5 mm graded stone aggregat) as in padding of floor/ off surfaces finishees even and smooth surface, complete all as specifeid and directed.complete (up to 4th storey ) all as specified and as directed

M&L for 10 mm thick cement plastering in CM 1:4 on brick/concrete surfaces of roof and parapet, mixed with water proofing compound, as per manufacturer instruction finished even and smooth without using extra cement complete (up to 4th storey) all as specified and as directed by Engineer-in-Charge. Note :- Water proofing compound shall be measured and paid separately.

Supply only liquid water proofing compound complete all as specified and directed.

M&L water proofing treatment on roof and sunken portion of floor and vertical surface consisting as under:- (a) Applying evenly a coat of bituminous primer conforming to IS-3384:1986 @ 0.30 Kg/sqm including preparation of roof surfaces (b) Applying evenly a tack coat of industrial bitumen 85/25 @ 1.2 kg/Sqm on plaster surface all as specified. (c) A layer of 3mm thick APP polymeric membrane of weight not less than 3.60 kg/sqm, reinforced with polyester non-woven fabric (weight not less than 160gm/ sqm), duly sealed at over laps & joints with end laps of the 10cm and side over laps of 7.5cm by flame (by torch application) all as per manufacturer’s instructions, complete all as specified and directed.

M&L for applying one coat Bitumen water proofing aluminium heat resistance paint on the roof as per manufacture instructions complete all as specified and directed by Engr-in-Charge.

Demolition of brick work or stone/boulders masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars etac but excluding ashlars facings, dressed stone work and precast concrete articles complete all as specified and directed by Engineer-in-Charge.

M&L for brick work with sub class 'B' bricks straight or curved on plan exceeding 6m mena radius built in cement mortar 1:4 complete all as specified and directed by Engr-in-charge

Taking down Cement Plaster from wall and ceiling of any description from Brick/concrete surfaces including raking out Joints, hacking for Key, scrubbing down with Water, etc., and removing same from the Site(s), complete all as specified and as directed. Note :- Rate included (up to 4th storey) with necessary scaffolding and safety measures

M&L Cutting grooves in brick wall, 75mm wide and 65mm deep and shaping horizontal face of groove with cement mortar 1:3 (up to 4th storey) complete all as specified and as directed.

M&L for 15 mm thick rendering in CM 1:4 on brick/concrete surfaces of wall, mixed with integral water proofing compound, the surface shall be cured and allow to dry, finished even and smooth without using extra cement (up to 4th storey) complete all as specified and directed by Engineer-in-Charge. Note :- Water proofing compound shall be measured and paid separately.

M&L for 15mm thick rendering on brick or concrete surfaces in internal surfaces in cement mortar 1:6, finished even and smooth without using extra cement complete all as specified and as directed by Engineer-in-Charge.

M & L for 5 mm thick rendering in CM 1:3 on brick/stone/concrete surfaces of ceiling finished the surface even & smooth without using extra cement including preparing of new plastered surface of ceiling and applying two coats of white wash over a coat of primer complete all as specified and directed by Engr-in-Charge.

M&L for Washed stone grit plaster on exterior walls in two layers, under layer 12mm cement plaster 1:4 (1 cement: 4 coarse sand mixed with Liquid WPC) furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 3kg of cement per square metre, top layer 15mm cement plaster 1:1/2:2 (1 white cement: 1/2 coarse sand: 2 stone chipping 6mm t0 10mm nominal size) in panels with groove all around as per approved pattern including scrubbing and washing, the top layer with brushes and water to expose the stone chippings complete all as specified:- Note :- Payment for providing grooves shall be made separately

M&L for forming groove of uniform size 15mm wide and 15mm deep in the top layer of washed stone grit plaster as per approved pattern using Aluminium Channel, nailed to the under layer including removal of wooden battens, repair to the edges of panels and finishing the groove complete as specified and directed by Engineer-in-charge.

M&L for prepration of new plastered/un plastered surfaces of wall and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance,dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces including necessary (scoffolding 4th storey) complete all as specified and directed.

M&L for prepration of new wall surfaces and applying two coats or more distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, over 1 to 2 mm thick birla putty by auto Roller of required shade and colour complete, as per manufacturer's specification including necessary (scoffolding 4th storey) complete all as specified and directed.

M&L for comlpete removal of existing treatment from old decorated plastered surfaces of walls by vaccum based sanding machine complete all as specified, removal of nails etc and filling cracks/ hole with putty, applying wall care putty upto 1 mm thick as required (multipurpose mixer shall be used for uniform adn proper mixing of putty) and applying two coats of oil bound distemper white or coloured over a coat of approved primer by using smart periodical methodology/ auto roller, complete all as specified and directed by Engr-in-charge.

M&L for complete removal of existing treatment from old decorated plasterred surfaces of walls by vaccum based sanding machine complete all as specified, removal of nails etc and filling cracks/ hole with applying wall care putty upto 1 mm thick as required (multipurpose mixer shall be used for uniform and proper mixing of putty) and applying two coats of exterior emulsion anti fungal paint 100% acrilic smooth exterior paint @ 1.67 Ltr/ 10 Sqm, colour as approved by GE, over and including a coat of approved primer by using smart periodical methodology/ auto roller, complete all as specified and directed by Engr-in-Charge.

M&L for comlpete removal of existing treatment from old decorated plastered surfaces on ceilings by vaccum based sanding machine complete all as specified, removal of nails etc and filling cracks/ hole with putty and applying two coats of white wash white or coloured over a coat of approved primer by using smart periodical methodology/ auto roller, complete all as specified and directed by Engr-in-charge.

M&L for preparation of old surfaces of wood or wood based materials over 10cm width or girth and applying one coats of synthetic enamel paint complete all as specified.

M&L for preparation and old decorated surfaces of steel and iron surfaces of any description over 10 cm width or girth and applying one coats of synthetic enamel paint complete all as specified and as directed.

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing), removing demolished teiles & rubbish off the premises, complete in all respect as specified and as directed by Engr-in-charge.

M&L for 50 mm thick PCC 1:2:4 Type B0 (12.5mm Graded Stone Aggregate) as in sub floor etc., including rough top surface to receive floor finish complete all as specified and as directed.

M&L for Ceramic coloured/ printed non-skid tiles of size 7-8 mm thick( square / rectangular ) area of each tile exceeding 0.06 Sqm but n. exec. 0.11 Sqm laid as in floors setting and jointed with neat cement slurry over & including 15 mm thick screed bedding layers of cement mortar 1:6 and pointed with white or coloured cement to match the shade of tiles complete all as specified and as directed.

M&L for glazed ceramic colour tiles on vertical surface 350 x 250 x 7 to 8 mm/ 450x350x7 to 8 mm thick, set and jointed in neat cement slurry and pointed in white or coloured cement to match tile colour over and including 15 mm thick rendering in CM 1:4, complete all as specified and directed by Engr-in-Charge.

M&L for Non - skid Ceramic colour tiles 7 to 8 mm thick area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc including over 15 mm thick screed bedding layers of cement mortar 1:6 set and jointed in neat cement slurry and pointed in white or coloured cement to match he shade of the tiles, complete all as specified and as directed.

All as per Srl item No 34, here-in-above but on vertical surface such as skiriting, Dado,etc over 10 mm thick rendering in CM 1:4 complet all as specified and as directed.

Demolition of Stone slabs and tiles laid dry of any description or thickness in floors, aprons etc complete all as specified and directed.

M&L Granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite over 15 mm thick screed bed in CM 1:4 including grinding, moulding rounnding and polishing bedding as in, window Cill, kichen self plateform etc complete all as specified and directed by Engr-in-Charge.

M&L Machine cut kota stone slab flooring 20-25mm thick over 15 mm thick cement screed base in CM 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing over reoughfening of floor surface complete all as specified and directed by Engr-in-Charge.

M&L Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over 10 mm thick rendering in CM 1 :4 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing over reoughfening of vertical surface complete all as specified and directed by Engr-in-Charge.

Taking down chowkhat or frames with shutters (without taking off shutters from the frame) n.exc. 1.5 Sqm each all as specified and as directed.

Taking down chowkhat or frames with shutters (without taking off shutters from the frame) exc. 1.5 Sqm but not exc 4 sqm each all as specified and as directed.

Taking down shutters only exc 1 Sqm and n.exc. 2 Sqm each complete all as specified and directed.

S&F Framed work such as grills,gratings, etc.. with ends of bars shouldered and/or riveted,or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed.

S&F Pressed steel frames for doors, size 125 x 60 mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate,etc., complete, as specified, and directed by Engr-in-Charge.

M&L PCC 1:3:6 type C-1 (using 20 mm graded stone aggregate) for filling in bed block of hold fast etc complete all as specified and as directed.

S&F for 35 mm thick flush shutters, solid core construction, with block board and both faces are covered with 0.90 mm thick decorative face veneer with lipping/ frame to match, complete, fixed to chowkats all as specified and directed by Engineer-in-Charge.

M&L Second class hardwood 35 mm thickness, glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edge of framing plain, chamfered or rounded, fitted with cut and mitred beds for securing glass, etc.; sizes of members of shutters as specified in SSR Part-I Section - 8 clause 8.24 (a) supplied and fitted to chowkhat complete all as specified and directed.

S&F Second class Hard wood 35 mm thick Plain, framed,panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to Chowkhats all as specified and dircted by Engr-in-Charge.

S&F steel windows with glazing bars, side hung shutters with projecting type hinges, including steel handle, and steel peg stay dovetailed or welded ,complete in all respect as specified and directed.

S&F steel windows without glazing bars, side hung shutters with projecting type hinges, including steel handle, and mild steel flat strip for fixing wire mesh with nut and bolt, dovetailed or welded ,complete in all respect as specified and directed.

S&F factory made steel ventilator with top hung shutter including hinges steel peg stay, complete in all respect as specified and directed.

S&F PVC Solid moulded Architrave Door Frame of Size 50X47mm & more made out of min 5.0mm Coloured with Plastic Trim decorated PVC Sheet Reinforced with Mild Steel Square Tube as specified Manufacture’s Instructions complete all as specified and as directed.

S&F Factory Made PVC Solid moulded Architrave Door Shutter 30mm thick (Style) consisting of Frame made out of Mild Steel Tubes for Top and Bottom Rails, Mild Steel Frame shall be covered with heat moulded Plain Colour PVC 'C' Channel having a PVC Sheet Strip of 20mm width stuck inside with Solvent Cement for Stiles and Plain Colour PVC Sheet for Top Rail, Lock Rail and Bottom Rail on either Side and as Gap insert for Top Rails & Bottom Rail, Panelling of Plain Colour PVC Sheet to be fitted in the Mild Steel Frame welded/sealed to the Stiles and Rails with suitable PVC Sheet Beading and Joined together with Solvent Cement and fixing in the Frame at Site as per Specifications and Draw-ings, complete all as specified and as directed.

S&F Mild Steel Butt Hinges 100mm, Medium Weight, Cold Rolled ISI Marked and fixed, complete all as specified and as directed.

S&F 150 mm long Aluminium anodised handles, cast type, complete in all respect as speicfied and directed by Engr-in-Charge.

S&F for 150mm long anodised aluminum barrel tower bolt of extruded aluminium section fixed with flat head ss screw complete all as specified and as directed by Engineer- in- Charge.

S&F aluminum alloy sliding door bolt 300mm long with hasp, staple (bolt type) adnd fixing clips of sheets, cast of exctruded sections and fiing bolts or extruded section complete all as specified and as directed by Engineer- in- Charge.

S&F MS Helical door spring 300 mm long complete all as specified and as directed by Engr in Charge Note:- Helical spring will be fixed by welding if required in MS frame

S&F in repair PVC frame door seal of size 1 metre long fixed to wooden doors complete all as specified and directed by Engr-in-Charge.

S&F 140 mm long Floor door stopper of aluminium alloy body and tongue, anodised,with hard drawn steel spring,fixed in floor complete all as specified and directed.

M&L preparation of new or previously untreated surfaces of wood of any description not otherwise described width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified.

M&L preparation of new or previously steel surfaces of any description not otherwise described width or girth and applying two coats of synthetic enamel paint over & incl one coat of red oxide primer complete all as specified.

S&F stainless Steel Wire Cloth, 0.36mm nominal dia of Wire and average width of aperture 1.4 mm and fixed with Tinned Tacks of Mild Steel Wire Stapes, etc, complete all as specified and as directed.

S&F in repair stainless Steel Wire Cloth, 0.36mm nominal dia of Wire and average width of aperture 1.4 mm and fixed with Tinned Tacks of Mild Steel Wire Stapes, etc, complete all as specified and as directed.

Hacking out old broken glass (any th size, quality or description) from wooden or steel frames glazed with putty or fixed with wooden beads complete all as specified and as directed by Engineer- in- Charge.

S&F 04 mm thick Sheet Glass, Ordinary, Glazing as in Window Frames fixed with Wooden oil putty/rubber beads, not exc. 0.50 Sqm in Each Pane and fixed in repairs, complete all as specified and as directed.

Dismantling of boarding, any description, fixed in any position with nails/ screws, complete in all respect as specified and directed by Engr-in-Charge.

S&F 12 mm thick Veneered decorative plywood plywood, grade 1 (with BWR resin) with decorative face veneers on both faces; fixed with screws as in Kichen, Cup Board shutter, shelves etc to timber frame work all as specified and as directed.

S&F 2nd class hard wood plain fillets exc 6 sqcm but n exc 13 Sqcm sectional area, square, rectangular or tringular in section, wrought fixed with nails complete all as specified and as directed by Engineer- in- Charge.

S&F 50 mm long Stainless steel hinges suitable for cupboard complete all as specified and as directed by Engr-in-Charge

S&F Contineous (piano) hinges, mild steel powder coated of 40 mm width of flaps(when open) complete all as specified.

S&F 125 mm long extruded aluminium alloy handles, fabricated type, anodised all as specified and directed by Engr-in-Charge.

S&F 125 mm long Hasp and staple, safety type,brass with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and directed.

M&L for 75mm thick PCC 1:3:6 Type C2 (using 40mm graded stone aggregate)as in plinth protection and courtyard, finished even and smooth/fair with out using extra cement complete all as specified

S&F in repair, 1000 ltr capacity Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) three layered, ISI marked, hoisted and fixed in position including tank neeples of required size and 20 mm bore dia of pipe ball brass valve high pressure with plolythelene float and flynut complete all as specified in SSR Part I complete all as specified and as directed.

S&F in repair ball valve high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed 20 mm bore complete all as specified and directed by Engineer in charge.

S&F Galvanised Steel Water Tubing 15mm Bore (dia), ‘Medium Grade’ ISI marked with all Fittings, fixed to concealed or on Walls, Ceiling or laid in Floors or any other Situ-ation including taking down of old GI tubing complete all as specified and as directed.

S&F Galvanised Steel Water Tubing 20mm Bore (dia), ‘Medium Grade’ ISI marked with all Fittings, fixed to concealed or on Walls, Ceiling or laid in Floors/walls including Taking down old GI tubing, complete all as specified and as directed.

S&F in repair Fancy type two way Bib tap 15mm Bore,Chromium Plated, screwed down high pressure with or without lettered ‘HOT’ or ‘COLD’ with long screwed Shanks and Fly-Nuts, screwed for Iron Pipe and fixed-in-repairs, complete all as specified and as directed.

S&F in repair Brass CP fancy type Bib taps 15mm Bore (dia), Chromium Plated Long Body, screwed down, screwed for Iron Pipe or for Brass Ferrule, complete all as specified and as directed.

S&F in repair Angle Stop valves 15mm Bore (dia), fancy type,Chromium Plated, screwed down, screwed for Iron Pipe or for Brass Ferrule complete all as specified and as directed.

S&F in repair Stop valve CP 15mm bore(Concealed type), cast copper alloy, screwed down, high pressure with long shank or butterfly handle screwed both ends for iron pipe or union, complete all as specified and as directed..

S&F in repairs, 20 mm Bore gun metal Gate/Globe half turn valves with iron wheel/Lever fixed-in-repairs complete all as specified and directed by Engineer in charge.

S&F in repair chromium plated shower rose fancy type fixed to 15 mm bore pipe all as directed by Engr-in-Charge

S&F in repair Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.00 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified.

S&F in repair Stainless steel Towel Rail 600mm Long and 20mm dia, as Approved, fixed complete all as directed.

S&F in repair Vitreous China Soap Dish, Single, as Approved, fixing with Brass Chromium Plated Screws including Taking down unserviceable Soap Dish of any description, complete as all specified and directed.

M&L Vitreous China White Wash down Water Closet Pan (Pedestal Pattern) including Bolts, (excluding Flushing Cistern and Flushing Pipe) with white Plastic Seat cover, with Recessed Bottom closed pattern and Cover including Mild Steel Chromium Plated Aluminium Hanging Device and fixed-in-repairs, including Making Good disturbed Surfaces with Cement Mortar 1:3, complete all as specified and as directed. (Make :- CERA/PARRY WARE/HINDWARE or equivalent)

S&F Viterious china Squatting pan including connection to trap, and to flushing pipe, anti-syphonage pipe, size 580X440 mm White, with ‘P’ or ‘S’ Trap, Integral Foot Rest, providing Joints between Flush Pipe and Socket of WC Pan excluding Flushing Cistern and Flush Pipe), fixing with and including provision of 150mm thick Lime Concrete Bedding including taking out unserviceable WC Pan and connected Items, complete all as specified and as directed.

S&F in repair PVC Flushing Cistern 10 LITRE capacity, Low Level Valve Less, Symphonic Action type, White, with Inlet, Ball Valve, Float and Handle including a Pair of Cast Iron Brackets duly Painted/Erecting Stand and PVC connection pipe 15mm size, PVC Flush Pipe of polythene 32mm dia for Low Level Flushing Cistern including Cutting and Pinning in Ends, Making Good Disturbed Surfaces in Cement Mortar 1:3 and fixed including , complete all as specified and as directed.

S&F Vitreous China 550 x 400 mm Size Oval Shaped Wash Hand Basin White with 32mm dia Brass Chromium Plated Waste Fitting, including Cutting Chase cutting in wall and Pinning in Ends, Making Good Disturbed Surfaces in Cement Mortar 1:3 and fixed, complete all as specified and as directed.

S&F in repair Fancy type Pillar Taps mixer 15mm Bore,Chromium Plated, screwed down high pressure with or without lettered ‘HOT’ or ‘COLD’ with long screwed Shanks and Fly-Nuts, screwed for Iron Pipe and fixed-in-repairs, complete all as specified and as directed.

S&F in repair 6mm thick glass corner shelf (12"x12") with C type Brass CP bracket, complete all as specified and directed by Engr in charge.

S&F in repair, 6mm thick Glass shelf (6 x 22 ") with Brass CP Bracket , brass nut, SS railing complete all as specified and directed by Engr in charge.

S&F High pressure PVC connections pipe 600mm long suitable for Hot and Cold water for 15mm size with Brass CP Check nut complete all as specified and directed by Engr-in-Charge.

Dismantling of old existing PVC/CI/concrete pipes of any description, jointed in cement mortar up to 100 mm dia and removing to store complete all as specified and directed.

S&F 100mm dia sand cast iron soil, waste and vent pipes in any length with or without ears with cement joints fixed to walls with oval access door complete all as specified and directed.

S&F 75mm dia sand cast iron soil, waste and vent pipes in any length with or without ears with cement joints fixed to walls complete all as specified and directed.

S&F PVC (SWR) Pipes 110mm in Bore (dia), Single Socketed, in any length with Rubber Ring Joints fixed to Walls/Floors, etc, including Taking down /up unserviceable Pipe, complete all as specified and as directed.

S&F PVC (SWR) Pipes 75mm in Bore (dia), Single Socketed, in any length with Rubber Ring Joints fixed to Walls/Floors, etc, including Taking down /up unserviceable Pipe, complete all as specified and as directed.

S&F 100 mm dia CI branch pieces, single (equal or unequal) ordinary or inverted (Spigot or socket type) or with paralled branches with ovel access door complete all as specified and directed.

S&F 100mm dia CI bends, diminishing pieces or tapers (larger bore measured) complete all as specified and directed.

S&F 75mm dia CI branch pieces, single (equal or unequal) ordinary or inverted (Spigot or socket type) or with paralled branches with ovel access door complete all as specified and directed.

S&F 75mm dia CI bends with oval access door, diminishing pieces or tapers complete all as specified and directed.

S&F 110 mm dia PVC (SWR) Bend suitable , complete all as specified and as directed.

S&F 75 mm dia PVC (SWR) Tee with access door , complete all as specified and as directed.

S&F 75 mm dia PVC (SWR) Bend , jointing with s, complete all as specified and as directed.

M&L for in repair 100mm CI floor/nahani trap with steel grating including jointing and breaking/ dismantling any type of floor and making good cement concrete to the B-1 (1:2:4) and testing after fixing complete all as specified and directed by Engr-in-Charge

S&F Grating doom 100mm dia of PTMT (Minimum weight 25gms) complete all as specified and directed.

S&F in repair 25mm dia aluminium powder coated Curtain rod with decorative nobes on both side including MS bracket for fixing in the wall by drilling and fixing wooden gutties all as specified and directed by Engr-in-charge.

S&F Stainless steel sink, 1.00mm thick for kitchen or laboratory, with plug, waste pipe, washers, including cantilever cast iron brackets, connecting union etc.,overall size 495mm x 420mm with bowl size 410mm x 330mm x 160mm Chromium Plated Waste Coupling and Washer including Bedding in Cement Mortar 1:4 to Dwarf Wall and Connection to Pipe complete all as specified and as directed by Engr-in-Charge.

S&F in repairs for Steel Plate Rack size 2'x3'x9mm thick Steel plate complete all as specified and directed by Engr-in-Charge.

Demolition of Cement Concrete reinforcement roof, floor (Other than ground floors), beams , staircase, landing, chajjas and similar suspended works etc.

M&L for RCC (Nominal mix) type B1, 1:1 1/2:3 (20 mm graded aggregated) as in slab supported walls, beams and columns in floors, roof, landing, balconies,chajjas, conopies, cooping deck slab and selves and the like complete all as specified and directed.

M&L Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and as directed by Engr-in-Charge.

M&L Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed.

Re-baring by drilling holes and fixing nozzle if required in existing concrete/brick work as in column, beams, slabs and foundation etc in any position and any description size of hole 14mm, 16mm & 22mm suitable for dowels of size 10mm, 12mm & 16mm respectively (minimum depth 140mm for 10mm & 12 mm dia bars and 180mm for 16mm dia bar, cleaning the surface properly with blow out pump & round brushes and fixing of dowel bars with epoxy resin (resin+hardner). Make: Sika, Fosroc or concressive 1450 of BASF complete all as specified and directed by Engr-in-charge. Note:- (i) Adequate lap length shall be provided as per IS-456-2000. (ii) Reinforced TMT bars where incorporated in work will be paid under the relvent items. (iii) The work shall be carried out upto four storied building with scaffolding and in patches as directed by Engr-in-charg e. (iv) Rate for scaffolding and formwork wherever required and as directed to be included in quoted rate. (v) The works will be executed in different buildings and at scattered locations.

M&L for broken stone or boulders hardcore of gauge not exc 63 mm, deposited, spread and levelled in layers not exc 100 mm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for 75mm thick cement concrete 1:4:8 type D-2 using (40mm graded stone aggregate ) as in sub base of floor path and hard standing complete all as specified and directed.

M&L for 75 mm thick cement concrete 1:2:4 type B-2, (using 20 mm crushed and graded stone aggregate) on path, complete in all respect as specified and directed.

M&L Chequred cement concrete tiles 30 cm x 30 cm x 30 mm thick set and jointed and pointed in neat cement slurry with grey cement and pigment in floors including 20 mm screed bed in CM 1:6 complete all as specified.

M&L for gunntling to RCC works in column, beams, slabs, chajja, ceiling, facia landing , balconies and similar work etc by removing/dismantling of RCC (loose concrete) including plaster and cutting of steel bar including cleaning of surfaces with wire brushes and applying epoxy, paint anti corrosive coating of minimum 40-50 microns thick with sikatop Armatec 108 or Colusal VL of MC Bauchemie to rusted steel reinforcement after removing cleaning all rust and supply and fisng with sufficient fastners/concrete nails/welding at regular intervals welded steel wire mesh 50mmx50mm with 4mm dia steel wire as faces/drops and applying epoxy based or other equivalent suitable bonding against treatment to be carried out on old concrete surface with Sikadur 32 of Sikaa. Nito bond EP of fosroc or equivalent (as per manufacturers instruction) to bond old and new concrete mixing @ 2% by weight of cement polycrete and providing gunniting with a minimum pressure of 2 to 2.5 Kg sqcm with varying thickness from 25mm to 100mm as per requirement at site gunniting in cement mortar (1:2) (one pat of cement and two part of ghaghar sand) and plastering in cm 1:4 to a uniform surface, wherever required at any height, location and positon complete all as specified and directed. Note: (i) After placing the additional reinforcement all conrete surface shall be thorughly scrubbing with. (ii) Additional reinforced TMT bars were incorporated in work however min 20mm cement plaster in 1:4 and necessary concrete wks related to gunniting to be included in quoted rate. (iii) Gunniting at Ground floor to 4th storey (iv) Anti corrosive protective coating for reinforced bars. (v) Work to be carried out as in patches as directed by Engineer-in-Charge. (vi) Rate for steel scaffolding and formwork wherever required and as directed to be included in quoted rate. (vii) All demolished material removed from MoD land completely to any location as per NGT Norms. (viii) The work will be executed in different buildings and at scattered locations.

M&L for welding in repairs thickness of Metal to be welded n.exc 6mm complete all as specified and directed.

S&F Brass Hat Pegs, Solid body, 175 mm to 250 mm and fixed, complete in all respect as specified and as directed by Engr-in-Charge.

M&L for Providing and injecting chemical emulsion for Post Constructional Antitermite Treatment along external wall where the apron is not provided using chemical emulsion at the rate of 7.5 litres per sq.m of the vertical surface of the sub-structure to a depth of 300mm including excavating channel along the wall and rodding etc. complete.

M&L for along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron complete all as specified and directed.

M&L for treatment of soil under existing floors using emulsion @ one litre per hole,300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors complete all as specified and directed.

Dismantling and re-fixing of existing IGL PNG pipe lines and meter box with reqd mtrls by M/S IGL only, complete all as specified and directed by Engr-in-charge.

Removal of demolished bldg materials including loading, unloading and stacking at destination, distance more than 05 km and up to 10 km as per NGT norms complete all as specified.

Note:- (a) The quoted rate shall be inclusive of carrying out work upto 15m height of building. (b) Water is not supplied by the MES. Water will be arranged by contractor and contractor should produced all necessary Test Certificates for portable water fit for construction and rehabilation as per relevant IS. Rate of Water tanker and rate of water testing are inclusive in quoted rate. (c) All debris will be removed from MoD land as per NGT Norms. (d) The contractor should make good of any damaged and disturbed surface and clean all cement/guniting etc patch on windows/doors/and all surface.

Taking down copper/aluminium point wiring (light points) complete, including fixtures and fittings such as switches, ceiling roses, pendents, regulators, sockets, light fittings etc. removing materials to store for keeping in safe custody or for taking credit (credit for the above items should be made as per conditions seperately) and making good disturbed surfaces of walls. floors, etc. complete all as directed

Taking down copper/aluminium submain wiring complete, including conduits of any kind, and removing materials to store for keeping in safe custody or for taking credit (credit for the above items should be made as per conditions seperately) and making good disturbed surfaces of walls. floors, etc. complete all as directed

Taking down main switches, distribution boards etc of any type and capacity along with the existing boards including MCBs/MCCBs and removing the same from site and making good the disturbed surfaces/portion of walls etc. all as directed.

Taking down fluorescent tube light fittings of any wattage or size and deposit to MES store or for taking credit complete all as specified.

M & L for point wiring (concealed on wall & surface/concealed on cealing) for one light/fan/exhaust fan controlled by one modular/piano switch one way in different locations/building including rigid non metallic PVC conduit, medium grade, ISI marked , 20 mm dia, with 1.5 sqmm FRLS PVC insulated & unsheathed, stranded copper conductor of 1.5 sqmm as continuous earth connected to common earth dolly, complete all as specified and directed by Engr-in-charge.

M & L for point wiring (concealed on wall & surface/concealed on cealing) for bell point controlled by one modular/piano switch one way in different locations/building including rigid non metallic PVC conduit, medium grade, ISI marked , 20 mm dia, with 1.5 sqmm FRLS PVC insulated & unsheathed, stranded copper conductor of 1.5 sqmm as continuous earth connected to common earth dolly, complete all as specified and directed by Engr-in-charge.

All as per item No 138 here-in-above but for 5 Amps 5 Pin socket outlet on the same board complete all as specified and directed.

All as per item No 138 here-in-above but one 5 pin, 5 Amp socket outlet on independent board not below the switch board of the light point in the same vertical plane complete all as specified and directed.

All as per item No 138 here-in-above but one 5 pin, 15 Amp socket outlet on independent board for power point with 2.5 sqmm size copper wire complete all as specified and directed.

All as per item No 138 here-in-above but One light point controlled by two 2- way switches with cables 1.5 sqmm size copper wire complete all as specified and directed..

S& F ceiling rose, 2 to 3 terminals complete all as specified and as directed .

S&F Modular switch, one way 6 Amps , 1 module complete all as specified and as directed .

S&F Modular Socket , 6 A-2/3 Pin combined 2 module all as specified and directed.

S&F switch modular one module 2 way 6Amps complete all as specified and directed.

S&F Modular Bell push 6 Amps , 1 module complete all as specified and as directed .

S&F twin socket modular type heavyduty out let 6 pin 6/16 Amps 2 module, complete all as specified and as directed .

S&F switch Modular type 16 Amps , single pole one way 240 volts one module as complete all as specified and as directed .

S&F Modular Fan step Regulator Bell ,120 W-2 module complete all as specified and as directed .

M&L for metal flush box for fixing of switches for 1/2 module complete all as specified and as directed .

M&L for metal flush box for fixing of switches for 3 module complete all as specified and as directed .

M&L for metal flush box for fixing of switches for 4 module complete all as specified and as directed .

M&L for metal flush box for fixing of switches for 6/8 module complete all as specified and as directed .

Supply & fix Modular White cover plate with frame for 1/2 module complete all as specified and as directed .

Supply & fix Modular White cover plate with frame for 3 module complete all as specified and as directed .

Supply & fix Modular White cover plate with frame for 4 module complete all as specified and as directed .

Supply & fix Modular White cover plate with frame for 6/8 module complete all as specified and as directed .

S&F Modular type blank plate , 1 module as specified complete all as specified and as directed .

Taking down water heater storage type electric capacity 25/50 liters and refixing the same after repair of the bldg on same location including cleaning of the geyser body complete all as specifieds and directed.

Supply and fix PVC ventilating fan AC single phase 230/240 volts of size 200 mm sweep with louvers and connecting up including provision of cable from ceiling rose to connector to exhaust fan also including make suitable size hole on wall/window as per site requirement. Make : Havells/Bajaj/Usha/Orient/Orision.

Supply & fix sheet metal enclosure for 220 volts 20 Amps with a three pin and earth plug top with socket and one single pole MCB 20 amps complete as well as specified and directed.

Taking down fan, sealing cable end, dismantling blades and removing fan and blades to store complete all as specified and as directed .

Taking down of serviceable Exhaust fans and refixing the same on same positionincluding painting of any type of fans complete, in situ with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust etccomplete all as specified.

S&F Sheet metal enclosure DD SPN 240 Volts 08 way DB with 200 Amps rated busbar complete all as specified and directed.

Supply and fix factory made epoxy polyster powder coated VTPN distribution board Triple pole MCB 4 way 415V fabricated from minimum 1.6 mm thick CRCA sheet with double door (IP-43 protection) fixed flush to wall and standard DIN rail, earth bar and cable ties for cable management, provision for 125 Amps MCCB as one incommer and 12 outgoings single pole MCB with 2 Neutral bar, 2 Earthbar, Fully insulated busbar rated capacity above 160Amp, shrouded Neutral bars and cable ties for cable management complete all as specified and confirming to IEC 61439-3,Reversible door IP 43 & IP 54. Make: Legrand /Siemens/Schneider. Note: Cutting on wall and taking out old one and then flushing new DB and making all the connection as before and any accessories required to fix the DB including making good the disturbed surface is deemed to be included in quoted rate.

S&F MCB SP 6-32 Amps ,10 KA 230 Volts ,50 HZ complete all as specified and as directed by Engineer -in -charge .

S&F MCB SPN 32 Amps ,10 KA 230 Volts ,50 HZ complete all as specified and as directed by Engineer -in -charge.

Supply & Fixing MCCB 100 Amps 4 Pole, 415 V, fixed thermal & fixed magnetic setting electromechanical type with Ics=75 % of Icu , with breaking capacity 16 KA conforming to IS: 13947-II complete all as specified and as directed.

M&L for concealed sub main wiring three run of 06 sqmm PVC insulated unsheathed copper conductor cable ISI marked 1100 volts grade drawn in and including PVC surface conduit suitable size of medium grade fixed on wall/ceiling/passing through wall etc connected as required at site complete all as directed. Note- (a) Two runs of single core cable with one run of earth continuity cable including PVC conduit and its accessories will be measured and paid as one unit). (b) Make disturbed surface good to wall/floors as existing surface.

All as sper Srl item No 170 here-in-above but three run of 4 sq mm complete all as specifed and as directed.

All as sper Srl item No 170 here-in-above but three run of 2.5 sq mm complete all as specifed and as directed.

Supply , Laying , testing and commissioning XLPE insulated and PVC Sheathed , galvanized steel strip or wire armoured , heavy duty electric cable with multi stranded aluminium conductor, 1100 volts grade of size 25 sqmm 3.5 core ISI marked complete all as specified and directed by Engineer - In - Charge.

Excavation in treanches in soft loose /soil not exc 1.5m wide and not exc 1.5m deep and getting out for taking out and laying cables foudation etc. Brick PCC cables protection cover shall be retrieved and kept in safe costody for reuse).

Returning filling in including spreading leveling waterning and well remmaning in layers not exc 25cm thick all as directed .

Removing of surplus spoil to a distnce not exc 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed.

M&L for dry clean sand filling in trenches below and around under ground cable cushioning complete all as specified and directed. Note :- Thickness of sand cushioning shall be measured after punning.

M&L for brick protection with sub class 'B' Designation 75 old bricks laid dry flat 23cm in width over sand cushioning in trenches as perpendicular to the direction of underground cable complete all as specified and as directed.

Removing and refixing LED light fittings (batten/lamps/bulkheads) of any capacity, 220V, AC decorative box type after cleaning with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

S&F in replacement of 4 ft 18/20 watt Decorative ultra slim aluminium LED lighting fixture with high lumen output, environmental friendly, energy complete all as specified and by Engr-in-charge.

S&F in replacement of 2 feet 09/10 W slim LED battern (cool day light) Basic all purpose surface and wall mounted with polycarbonate housing & integrated with electronic driver complete all as specified and directed.

Supply and fixing LED bldg light fitting 60 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and as directed.

M&L Earthing complete with galvanised steel earth plate electrode 60×60cm.× 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less'than 1.5 metres below normal ground level, connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 connected to earthing test point all as specified or indicated including testing on completion complete all as specified and as directed.

Supply and fixing ceiling fan complete with blade, down rods, electronic regulator and accessories, 230 V, 1200 MM sweep. Min air delivery 210 CFM with service value 6.00 BEE five star rated with brushless direct current motor (BLDC) complete all as specified and as directed.

Taking up and down 40 mm bore steel tubing and connections, and removing materials for taking credit all as specified and as directed.

Taking up and down 25/20 mm bore steel tubing and connections, and removing materials for taking credit all as specified and as directed.

Supply and Fix 40 mm dia Galvanised Steel water tubing (ISI Marked ) medium grade with and including all tube fittings and fixtures such as GI bends tee union etc in trenches/fixed to wall/ fixed on piller complete and connecting to water supply pipe line and testing complete all as and as directed.

All as per srl item no. 187 here-in-above but 25 mm dia complete all as specified and directed

All as per srl item no. 187 here-in-above but 20 mm dia complete all as specified and directed.

M & L for cutting/threading of GI tubing in position of size 100/80 mm dia pipe for insertion of new Tees, branches etc. of 25/40 mm dia bore dia all as directed.

S & F 40 mm dia Gun metal , globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed

All as per srl item no.191 here-in-above but 25 mm dia complete all as specified and directed.

Schedule of Credit

V.K. Enterprises (BID ID -3363595)

M/S Rohit Enterprises (BID ID -3363459)

BRIJ MOHAN LAL AND CO. (BID ID -3363097)

Green Leaves (BID ID -3355076)

akhil enterprises (BID ID -3362739)