02/HDA/EC-ELECT/2025 2026

Amount

Supply, delivery of 10 Mtr. Hot Dipped galvanized Octagonal Pole with Top Dia. - 90 mm, Bottom Dia. - 210 mm, Section Length - 10000 mm 3 mm Thickness, 300 mm x 300 mm x 20 mm BASE PLATE. (GI As per IS 2629) (As per attached Drawing). M24 x 750 mm x 4 nos. J Type Foundation Bolts, Triple Arm Bracket (3000 mm. Single Arm with 1500 mm long Double Arm) on all side with 48.3 OD GI Pipe [Utkarsh/Bajaj/Velmont/Transrail].

Installation of 10 Mtr. long G.I octagonal pole.

Supplying & delivery of 200 Watt LED Flood light with pressure die cast aluminium housing, IP66 protection, road way luminaire with high power LED. Make & Model No. Philips- BVP283 LED240 CW FG SY5NB PSU SPD) as per direction of EIC.

Supplying & delivery of 150 Watt LED Flood light with pressure die cast aluminium housing, IP66 protection, road way luminaire with high power LED Make & Model No. Philips- BVP283 LED181 CW FG SY5WB 150W SPD V1) as per direction of EIC.

Preparation of RCC foundation of 500 mm dia and 1800 mm height (1500 mm below the Ground Level and 300 mm above the Ground Level) with required rod, cement, chips and sand etc. at the ratio 1:1:5:3 with ground bolt 4 nos. for fixing the 10Mtr Height G.I Octagonal pole (Excluding supply and delivery of Nut Bolts).

Supply and delivery of 1.1 KV grade 2 C X 10 Sq mm XLPE insulated and PVC sheathed aluminum armored Cable. As per IS 7098 Part -1 with latest amendment if any. The cable should have ISI mark.) [Havells/Polycab/Gloster]

Supply, drawing and Connection of luminaries with 3C X 1.5 Sq mm pvc insulated FR copper conductor through 10 mtr. Poles from looping box to light fittings as required)[Havells/Polycab/Finolex].

Fixing only Street / Floodlight Fitting with suitable tie clamps and MS plate for mounting on Pole/Tower or similar structure. (excluding the cost of RCC Foundation)

Supply of HDPE Plb Duct pipe of size 32/26 mm.

Supply and Installation of HDA printed logo suitable 15"×9" on GI Octagonal/tubular Pole, on brick foundation of meter box, feeder pillar box (3 nos. logo/pole).

Supply and fixing of SPMCB "C" Curve 1-4 Amp with ISI marked to be placed on a din channel of Pole and connection with Terminal connector at the suitable location of the pole.(Legrand).

Lifting of the running Under Ground Cable coming to the looping cable Box upto the top of the muffing above the top of the ground level by drawing through 40 mm dia rigid pvc pipe of superior Quality and tiding the same by no 10 SWG GI wire with the pole including supply of pipe & wire & filling the top of the pipe/pipe hole with bitumen and neat cementing properly (average run- 1.5 mtrs./run X 2 runs per pole).

Supply, delivery, installation, testing & commissioning of single phase Feeder pillar box of size 1000 X 750 X 400 mm made of 2.5 mm thick CRCA steel sheet with zinc powder coated outdoor type with top canopy, sides having lovers for ventilation, double door, complete with cu bus-bar, provision for installation of single phase meter at right side of the feeder pillar with individual locking arrangement as per direction of engineer-in-charge. (Consisting of following items in the feeder pillar) i) 40 Amp, 230 Volt Double Pole MCB 10 ka Breaking capacity (Legrand /L & T/Hager/ABB) -1 no ii) ML3 contactor (L&T) -1 no iii) Mechanical Time Switch of daily dial with battery backup (L&T) -1 no iv) 16 Amp. SPMCB "B" Curve of 10 KA Breaking Capacity -4 no. v) Indicating LED Lamp-2 No vi) Cubical Ilu Lamp & Switch - 1 No. vii) Toggle switch - 1No viii) Power Connector 4 Way 32 Amp -3 Set ix) Multifunction meter with C.T - 1 set xi) Copper Wire for internal wiring Installation of the feeder to be done by the earth cutting, brick soiling and cc foundation as required & sand filling, ramming and muffing around the feeder pillar box by brick and cement mortar work as per the direction of the Engineer-in-charge.

Finishing of the XLPE/PVC insulated armoured cable ends by soldering with cable sockets and insulated tapes etc., including supplying sockets, soldering materials, tapes etc. and making connection to switch, BDB and BBC etc.

2 Core X 10 Sqmm

Supply GI earth Spike (1830 X 20 mm) (Each Pole).

Earthing complete with driving of Erath spike & connection of Earth electrode with noncurrent caring metallic parts of supports (Each Pole).

Laying of one No. HDPE Pipe in underground trench 460 mm wide x 760 mm average depth including filling the trench with shifted soil, leveling up and restoring surface duly rammed.

Supply & fixing medium gauge GI Pipe (ISI-Medium) Protection with necessary fittings and jointing materials as required. 40 mm dia.

Laying of Cable by Jack push method through micro tunneling 2-3M deep under black top surface with excavation of double earth pit 1400×600×3000 mm on hard soil, laying of pipe, refilling and ramming of soil in earth pit, restoration of road surface etc (Excluding the supply of Pipe)

Laying of one no. cable up to 35 Sq mm in underground trench 460 mm wide x 760 mm average depth, with brick protection on the top of the cable with 8 (eight) Nos. bricks per meter, including filling the space between the brick & cable and also the trench with shifted soil, leveling up and restoring surface duly rammed.

Laying only Cable up to 50 sq.mm through existing RCC/Hume/ GI /HDPE Pipe/open masonry trench for single, 2, 3, 3½ & 4 core

Priming one coat on timber or plastered surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc. (2.8 sq.mm. per panel x 1+1.54 sq.mm Pole x 1).

Painting the vertical end faces of posts, wheel guards or railing or parapet with alternate bands of different colours as directed by the Engineer-in-charge with approved synthetic enamel paint. (2.8 sq.mm per panel x 1+1.54 sq.mm Pole x 1).

GST @18% of Total Amount

CESS @1% (Total Amount including GST)