Renovation of room no 19 (Bill section) along with construction of cabin at ground floor, Udyog Bhawan, Jaipur

Amount

"Providing and fixing Hollow core partition wall using 50x50 mm Chir wood frame 600 mm c/c on both directions excluding door opening portion with antitermite treatment as per direction of Engineer incharge and as per specifications (Drawing enclosed) as below :1. 50x50 mm Chir wood frame 600 mm c/c on both directions shall be fixed upto roof/beam height i.e. 10ft/8ft. Frame should be supported at floor and roof with horizontal post (wherever required) of size 50X50mm thick Chir wood 2. 12 mm thick MDF board both side (upto height i.e. 7ft of total false ceilig height of 8 ft) shall be fixed on both sides of chir wood frame. Laminate (1mm) of approved quaity & colour shall be fixed/pasted over MDF board upto 7ft height.3. Frosted glass of 8mm thickness (Saint Gobain or equalvent etc.) shall be fixed in a heigt of 1ft (12") at the top end of 8ft height wall panneling. complete as per direction engnieer incharge. Teak wood beading 25mmX20mm is to be used for glass fixing. Teak wood beading and frame is to be finished with melamine polish.4. Total thicknees of hollow core wall partition shall be 76mm. (Chir wood frame + MDF board on both sides + laminate on bothsides)5. The cost is inclusive all labour, material etc complete in all respect as per drawing & design enclosed & approved by engineer in charge.6. Area of aminated parttion below false ceiling only to be measured for payment. (Perspective view shall be as per enclosed drawing-A) "

Providing and fixing of 30mm thick Flushdoor of approved brand with 5mm thick glass fixed in the half portition with 25x20mm teak wood beading to be finished with melamine polish. On the remaing part of the door should be finished with 1mm thick mica as per approved brand and shade and colour. The door also shall have the door closer of good quality make of dorma or equalent with approved brand mortise lock, stopper etc. with brass accessosries. The cost is inclusive all labour, cutting, makeing hole etc. complete in all respect as per approved by engineer in charge.

Providing and fixing of Workstation Systems as per specifications: (a)size 2 seater linear overall size : 2820 x 650 x 1350mm (L x W x H ) - 14 set, Each seat size : 1350 x 600 x 750mm (L x W x H): (b) Aluminium Partition: There would be partition panels of overall thickness of 60+0.5mm of minimum Blow sizes fixed in a cross sectional fashion with the help of a right angle/straight connectors of suitable size, as per requirement and drawing. The panel would be made with a combination of Aluminum sections of overall thickness of 60mm and MDF board sandwich panels of an overall thickness of 57mm +1mm.The lower section of the partition panel will be of height 750mm up to the worktop and it will be covered with Laminate of matching color on both sides of the panel. The partition portion just above the worktop of height 450mm will be provided with a Matching Mica Laminated board on both side. The partition panel will have a double cable wire raceway management system in the bottom & above the worktop of an overall size of 120mm x 60mm. The inner side having a cable management system which provides a usable area of 90mm x 57mm. The cable management system is provided with a bottom cable raceway cover of 100mm width for easy laying of cables. The cover is having push fit arrangement for easy opening and compact fixing of cable raceway. Each aluminum partition section will be duly powder coated with matching colour of minimum 40-60 microns thickness and it should be able to withstand minimum 1000 hrs. of salt spray test/impact resistance of 150 kg-cm. Worktop: The worktop will be made out of 25mm thick laminated MDF board all Flat edge duly sealed with1.3mm thick PVC edge banding of approved color pasted with PUR (Polyurethane reactive adhesives) Glue on through-feed edge-banding machine for better bonding of edges. The worktop will be joined with proper jointers. Pedestal Unit: The pedestal unit of size 725 x 375 x 450mm(H X W X D) made out of 18mm thick prelaminated MDF board, having three number of drawer units, the two top units of 150mm depth each and the bottom drawer of 375mm depth used as the file storage unit. The front shutters matching with top surface finish all flat edge 1.3mm thick PVC Edge banding of matching colour on the remaining sides. The drawers are mounted on steel telescopic channels including necessary hardwares, handle locks etc. Accessories: Provision with each seat one keyboard tray(metal), CPU trolley (metal) The entire workstation is complete in all respects and made as per specification and as directed by engineer-in-charge. (As per drawing -B)

EXECUTIVE CHAIR (with headrest and Black colour): The seat is made up of 1.4± 0.1 chick hot - press 4 plywood upholstered with fabric and moulded polyurethane foam. It has a seat depth adjustment of 5.0±0.3 cm integrated in the seat through a sliding mechanism. SEAT SIZE: 50.0cm (W)x 49.0cm(D).The Back is injection moulded in Glass filled Polyamide which is upholstered with Mesh fabric. The back consist of adjustable Lumbar support made of injection moulded Polypropylene having an adjustment of 6.0±0.1cm.BACKSIZE: 50.0cm(W) x68.0 cm(H).The polyurethane foam for seat is of density 55± 5kg/m3. It is made of glass filled Polyamide arm structure with PU arm top and height adjustment of 7.0 ±0.5cm.The arm top has swivel and To-For movements. To-for movement is 6.0± 0.5cm.The inner tube of armrest is chrome plated. The mechanism is designed with the following features:• 360° revolving type.• Centre tilt Synchro• 3 position (including upright lock) giving option of variable tilt angle to the chair with anti shock feature. The Headrest is injection moulded din Glass Filled Polypropylene which is upholstered with foam and fabric has an adjustment of 6.0± 0.1cm & its assembled over the Full back chair. The pneumatic height adjustment is chrome plated with an adjustment stroke of 9.0 ± 0.3cm.The pedestal is High Pressure Die cast polished Aluminum and fitted with 5 nos. twin wheel castors. The pedestal is 65.0±0.5 cm P.C.D. The twin wheel castors are injection moulded in black Glass filled polyamide having 6.0±0.1cm wheel Diameter. The Chrome plated tubular frame is made of Día2.8±0.03cm x0.2±0.02 cm the M.S. Round tube. The frame is fitted with plastic caps made of injection moulded glass filled Polypropylene. -75(W)* 75(D)* 100-109(H)* 44.5-53.5(SH).

VISITOR CHAIRS (Non-Revolving, Black colour) 1.SEAT ASSEMBLY: The seat assembly should be made up of 1.2 ±0.1cm. thick hot-pressed plywood , upholstered with fabric upholstery covers and moulded Polyurethane foam. SEAT SIZE: 47.0 cm. (W) x 48.0 cm. (D) 2.BACK ASSEMBLY: The back asembly. should be made of powder coated (OFT 40-60 microns) tubular frame of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. MS ERW tube designed with contoured lumbar support for extra comfort. The back should be upholstered using double layer spacer mesh fabric with high tenacity yarn. BACK SIZE : 46.5 cm (W) x 60.5 cm (H) 3.HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam should be moulded with density =45+/-2 kg/m3 and hardness load 16 ± 2 kgf for 25% compression. 4.ARMRESTS: The one-piece armrests should be injection moulded from black Co-polymer Polypropylene. 5.CENTRE-TILT mechanism: The mechashould be m should be designed with the following features: • 360° revolving type. • 17° ±2° maximum tilt on pivot at centre • Upright position locking. Tilt tension adjustment. 6.PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment has an adjustment stroke of 11.0 ±0.3cm. 7.TELESCOPIC BELLOW ASSY: The bellow should be 3 piece telescopic type and injection moulded in Black Polypropylene. 8.PEDESTAL ASSEMBLY: The pedestal should be injection moulded in black 33% glass-filled Nylon66 and fitted with 5 nos. twin wheel castors. The pedestal should be 66.3 ±0.5cm. pitch-center dia. (76.3 ±1.0cm with castors.) 9. TWIN WHEEL CASTORS: The twin wheel castors should be injection moulded in black nylon.

Providing and fixing luxury Roman Horizontal blinds of cloth type complete including curtain rod and all accessories as per direction of Engineer Incharge.

Executive Table with size shall be 2100 Width mm x 1600 Depth mm x 765 Height mm .The main top shall be of Particle board (1mm Mica for outer side and 0.8 mm inner side) 1800 x 795 mm.The top shall be 25 mm thick plus 15 mm frame and 2 mm PVC lipping on top .Also there shall be 0.35 mm PVC lipping on frame.The Modesty panel shall be 1100 x 405 x 46 mm thick particle board (1mm Mica for outer side and 0.8 mm inner side) with 0.35 mm thick PVC lipping.The Drawer Front shall be of size 500 x 170 x 16 mm thick Particle board (1mm Mica for outer side and 0.8 mm inner side) with 0.35 mm thick PVC lipping.The KBPT shall be 578 W x 284 D x 17 mm with 0.35 mm Thick PVC lipping.It shall have all panels of 17 mm thick Particle board (1mm Mica for outer side and 0.8 mm inner side).

SOFA 3 SEATER : seat foam: the seat should be made of pu foam with density 32 ± 2 kg/cu.mtr having an additional top layer of j pu foam with density 28 ± 2 kg/cu. seat should be upholstered with fabric or leatherette. 2) back foam: the back should be made of pu foam with density 28 ± 2 kg/cu. mtr with two additional top layer of supersoft foam of density 23±2 kg/cu. mtr, upholstered with fabric or leatherette understructre : understructure should be made up of 1.2±0.1 cm. thick hot pressed plywood ocp-qlta-pl14-18 4. dia 4mm zigzag spring assembly should be mounted in understructure for support and additional cushioning purpose leg assembly: it should be a welded assembly made in stainless steel (grade ss 202) tube & plate.Width (W): 205.5 CM. Depth (D): 92.0 CM. Height (H): 82.0 CM. Seat Height (SH): 45.0 CM.

2 Seater SofaSEAT FOAM : The seat is made up of PU foam in Density 28 ±2 kg/cu.mtr with an additional top layer of supersoft PU foam in Density 32 ± 2 kg/cu, upholstered with fabric or leatherette.BACK FOAM : The back is made up of PU foam in Density 28 ± 2 kg/cu. mtr with two additional top layer of supersoft foam of density 32±2 kg/cu. mtr, upholstered with fabric or leatherette.UNDERSTRUCTRE : Understructure is made up of 1.2±0.1 cm. thick hot pressed plywood [moisture resistance & termite proof as per IS:303] & pinewood of cross sections devoid of major knots & surface defects. 6 nos. per seat & 3.8mm Dia zigzag spring assembly is mounted over understructure for cushioning purpose.LEG ASSEMBLY : It is a welded Assembly made in Stainless steel (grade SS 202) tube & plate with plastic endcap.Width (W): 146.0 CM. Depth (D): 90.5 CM. Height (H): 85.5 CM. Seat Height (SH): 45.0 CM.

Bidder Name

Amount

AK JAIN AND ASSOCAITES(GSTN-08ABTPJ7664B1ZB)

Rashmi Enterprises(GSTN-08AAEFR3518G1ZA)

M/S JAIPUR CRAFT AND ART(GSTN-08AYMPA1844L1Z9)

G-CAD ENGINEERS(GSTN-NA)

M/S JAIPUR CRAFT AND ART

G-CAD ENGINEERS

Rashmi Enterprises

G-CAD ENGINEERS

Rashmi Enterprises

AK JAIN AND ASSOCAITES