Construction of Town Hall Building at Bokaro Under Bokaro District Jharkhand

Amount

Jungle clearance including weeding out shrubs and small trees upto 150mm dia and their removal as per specification and direction of E/I

BORING

HYDT: - Cost of Driling 200mmx165mmx125 mtr.deep bore well in all kind of Soil and rock in rural area for instalation of pump set with Hydrolic DTH Rig machine all complete including all materials, tools, driling rig, air compressure and equipments as well as fule, lubricants and cost of transportation of rig machine annd other vehical up to Site. (2 Nos.)

(a) From 0.00 M to 50.00 M below G.L.

(b) From 51.0 M to200.00 M

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge. 200 mm nominal size dia UPVC.

Supplying all tools, equipments and labour and doing washing and flushing and development of drilled tube well to give clean and clear water all complete as per direction of E/I.

Supplying labour, cement and calcium cloride or bentonite solution and equipments for groutinf the casing pipe after lowering in the bore including carriage of material to work site etc.all complete as per specification and direction of E/I.

Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete. 200 mm clamp

Supplying 100mm dis submersible pump sets confirming to 8034 and motor confirming to IS 9283 pump shall be suitable for various delivery head and discharge with stainless steel pump shaft and polypropylene/noryl impeller. Motor suitable for working on 415 + 10, 3HP, 50 Hz, AC supply with cable guard, thurst carbon/fiber bearing to withstand entire hydraulic thurst, water proof winding shall be provided. The pump set shall be suitable for diret coupling Pump shall have suitable outlet as per manufacturers design. Anti thurst stream lined non return valve shall be provided with pump, 3 meter submersible copper conductor cable in single/double run shall be provided with each pump. Submersible pump set 100mm dia (with Polypropylene/Noryl Impeller) up to 20 stages - 5 HP

D.O.L starter with S.S Enclosure with 380/415 Volt coil as per IS 3914 - upto 5 HP.

3 crore PVC insulated, PVC sheathed copper conductor flat submersible cable- Supplying, Flat flexible submersible cable with, copper conductor, PVC insulated and PVC sheathed. 3 core 4 sqmm

Supplying and lowering 40 mm dia. Column PVC pipe with all complete job.

Dewatering ;- Machines use per HP per hour Diesel Pump with complete job.

Earthwork in excavation in foundation trenches in ordinary soil (vide classification of soil item-A) and disposal of excavated earth as obtained to a distance upto 50 M. including all lifts, levelling, ramming the foudation trenches, removing roots of trees, shrubs all complete as per approved design, building specification and direction of E/l.

Extra for earthwork in hard soil as per specification and direction of E/l (vide classification of soil item-B)

Extra for earthwork in marshy, slushy and daldal soil (Vide classification of soil item F) all complete as per specifrication and direction of E/I.

Earth filling in foundation trenches and plinth in layers not exceeding 150 mm. thick well watered, rammed, fully compacted and fine dressed with earth obtained from excavation of foundation frenches within a lead of 50 M. and lift of 1.5 M all complete as per building specification and direction of E/l (Mode of measurement compacted volume).

Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor: cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor.

Providing P.C.C. M - 10 with nominal mix of (1:3:6) in foundation with approved quality of stone metal grade III (50 mm to 25 mm size) clean coarse sand of F.M. 2.5 to 3 including screening, shuttering, mixing cement concrete in mixer and placing in position, vibrating, striking, curing, taxes and royalty all complete as per building specification and direction of E/l.

Providing and laying in position ready mixed M-25 grade concrete for reinforced cement concrete work, using cement content as per approved design mix, and manufactured in fully automatic batching plant and transported to site of work in transit mixer for all leads, having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work, including pumping of R.M.C. from transit mixer to site of laying, excluding the cost of centering, shuttering, finishing and reinforcement, including cost of admixtures in recommended proportions as per IS : 9103 to accelerate / retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineer - in - charge. NOTE- (1) Cement content considered in this item is @ 330 kg/cum. Excess/ less cement used as per design mix is payable/ recoverable separately.

All works upto plinth level

All works above plinth level upto floor V level

Extra for providing richer mixes at all floor levels, Providing M 30 grade of concrete instead of M-25 grade B.M.C./Rmc. (cement concrete considered in M-30 is @360 Kg/m3)

Add for using extra cement in the item of design mix. Over amd above the specified cement concrete therein.

Extra for additional height in centering, shuttering where ever required with adequate bracing, propping etc., including cost of de-shuttering and decentering at all levels, over a height of 3.5 m, for every additional height of 1 metre or part thereof (Plan area to be measured). Suspended floors, roofs, landing, beams and balconies (Plan area to be measured)

1st. Lift

2nd. Lift

3rd. Lift

4th. Lift

Providing Tor steel reinforcement of 8mm. dia. rods as per approved design and drawing excluding carriage of M.S. bars to work site , cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction of E/l. . (Only valid for TMT Fe 500 {only vailid for TATA (tiscon), SAIL, JSPL, Electrosteel steels ltd., Bokaro and Vizal (RINL)}

Providing Tor steel reinforcement of 10mm.dia. bars as per approved design and drawing excluding carriage of M.S. bars to work site , cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction of E/l. (Only valid for TMT Fe 500 {only vailid for TATA (tiscon), SAIL, JSPL, Electrosteel steels ltd., Bokaro and Vizal (RINL)}

Providing Tor steel reinforcement of 12mm, 16mm, 20mm, 25mm, 28mm & 32mm dia. bars as per approved design and drawing excluding carriage of M.S. bars to work site , cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction of E/l. (Only valid for TMT Fe 500 {only vailid for TATA (tiscon), SAIL, JSPL, Electrosteel steels ltd., Bokaro and Vizal (RINL)}

Centering and shuttering including strutting, propping etc. and removal of form for :

Foundations, footings, bases of columns, etc. for mass concrete

Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc

Suspended floors, roofs, landings, balconies and access platform

Lintels, beams, plinth beams, girders, bressumers and cantilevers

Columns, Pillars, Piers, Abutments, Posts and Struts

Stairs, (excluding landings) except spiral-staircases

Providing Designation 100A B/W with Fly Ash Lime Brick (FALB) conforming to IS 12894-1990 (9"x4.5"x3") in cement mortar (1:4) in Foundation and plinth with clean coarse sand of F.M. 2 to 2.5 including 10mm thick mortar joints,cost of screening, raking out joints to 15 mm depth, curing, taxes and royalty all complete as per building specification and direction of E/l.

Providing Designation 100A B/W with Fly Ash Lime Brick (FALB) conforming to IS 12894-1990 (9"x4.5"x3") in cement mortar (1:4) in Superstructure with clean coarse sand of F.M. 2 to 2.5 including 10mm thick mortar joints,cost of screening, raking out joints to 15 mm depth, curing, taxes and royalty all complete as per building specification and direction of E/l.

Providing Designation 100A 112 mm thick reinforced B/W with Fly Ash Lime Brick (FALB) conforming to IS 12894-1990 (9"x4.5"x3") in cement mortar (1:4) in Superstructure with clean coarse sand of F.M. 2 to 2.5 including the cost of screening, raking out joints to 15 mm depth, curing, taxes and royalty all complete as per building specification and direction of E/l.

Extra for brick work for each consecutive floor above first floor including watering and scafolding, all complete as per direction of E/l.

Providing 12mm cement plaster (1:4) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/l.

Providing 6mm thick cement plaster (1:4) in ceiling with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/l.

Providing and laying plaster of paris putty of 2mm thickness over plastered surface to prepare the surfave even and smooth complete.

Providing 19 mm thick water proof cement plaster (1:3) with clean coarse sand of F.M. 1.5 with 5% cico or any other approved water proofing compound including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/l.

Extra for plaster work over exterior surface for each consecutive floor above first floor including cost of scaffolding etc. all complete as per direction of E/l.

Supplying, fitting and fixing good quality well dressed and well seasoned teak wood work in chaukhats in doors, windows, skylight, fanlights and celetial windows openings, including wedge over clamps all complete including application of two coats of wood preservative of approved quality on the surface butting walls and lintels all complete as per building specification and direction of E/l

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

Providing and laying Doublecharge vitrified floor tiles in different sizes (thickness to be specified by the manufacturer )with water absorption less than 0.08% and conforming to IS:15622 / ISO 13006 of approved make , in all colurs and shades, laid on 20mm thick cement mortor 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/sqm including grouting the joints with white cement and matching pigments etc., complete Size of Tile 600mm x 600mm

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), including pointing the joints with white cement and matching pigment etc, complete.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying 25 mm thick kotah stone tiles in risers of steps, skirting and pillars of approved size, texture and colour laid over 12mm thick cement mortar (1:3) and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing to granolithic finish with approved quality of carborandum stone including cost of curing, taxes and royalty all complete as per building specification and direction of E/I.

Providing and laying 20 mm thick Travastine stone tiles of approved size, texture and colour laid over 12mm thick cement mortar (1:3) and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing to granolithic finish with approved quality of carborandum stone including cost of curing, taxes and royalty all complete as per building specification and direction of E/I.

Providing and laying 25mm thick white makrana marble tiles in risers of step, skirting and pillars of approved quality over 12mm thick base of cement mortar (1 :3) and jointed with white cement slurry including rubbing and polishing to granolithic finish with approved quality of carborandum stone including cost of curing, taxes and royalty all complete as per building specification and direction of E/I.

Providing and laying Carpet Flooring of approved quality over slab suirface all complete as per building specification and direction of E/I.

Providing and laying Laminated Flooring of approved quality over slab suirface all complete as per building specification and direction of E/I.

Extra for flooring work for each consecutive floor above first floor complete as per direction of E/l

Supply and Installation of Epoxy Coat using good quality roller. Minimum film thickness of 200 microns should be applied. Two coats application. Care should be taken to ensure continuous film is achieved. Including Primer application, Surface preparation Line markings and arrow markings.

Supplying , fitting and fixing 32 mm thick good quality well dressed and well seasoned Sal wood battened shutters, ledged and braced in doors and windows with oxidised iron fittings such as hinges, sliding door, bolts, tower bolts, handles or rings, hooks and eyes, cleats, sand blocks as per schedule taxes and royalty all complete as per building specification and direction of E/l.

Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete : 50x12 mm

WATERPRROFING FOR OLD AND NEW ROOF SLAB : Providing and laying waterproofing treatment on Roof Slab by applying two component factory designed ,ready to use ,acrylic modified flexible material applied with brush ,roller, or spray for waterproofing coating caoting as per manufacturer specification and following steps surface praparation : Providing nd cleaning of concree surfase to remove the dust oil,grease including removal of existing loose paint/ coating and cement laitance by cleanning with compressed air and water jet including all materials ,laobour tools complete .Pondig test to be done after plugging all outlets and to checked from soffit to identify seepage ,leakage . on identification of seepage ,cement grouting to be done with non shrink expanding admixture of SIKA INDIA PVT Ltd /MYK Schomburg /Dr.Fixit/fosroc or equivalent . providing and Repairing of all corners and joints such as those between the parapet wall and the roof slab etc shall be campererd with 150 mmx150 mm fillet of mortor (Cement :sand-1:4) Admixed with acrylic polymer of Sika /Fosroc/MYK/Dr.Fixit damaged concreting base slab,dead cracks if any with an acrylic polymer modified repair mortor including coat of Bonding agent of the same with cement slurry including all material,labour,tools comlplete. b) Apply fisrt coat two component acrylic modified ,ready use ,flexible cementituous material on surface saturated dry roof and inside wall of paraphet wall upto 600 mm by brush or roller .After 1st coat of application ,45 GSM of fibre cloth to lay when fibre glass cloth when the first layer is still in green .1st coat to be applied @1.5kg/sqmt/coat. for the purpose of measurement entire treated surface will be maesured. c)2nd coat -To apply the 2nd coat of two component acrylic modified ready to use ,flexible cementituous material at right angle to the first coat over the glass fibre laid surface 2nd coat should be applied at @.7 kg /sqmtr /coat. for the purpose of measurement entire treated surface will be maesured.After three days of drying 2nd coat the rain water outlets to be plugged and ponding test to be done for 48 hrs to identify the seepage ,leakage from the sofit and if found necessary rectification to be done as per satisfaction of E/C. The waterproofing coating to protected from damage before screed over it.Waterproofing brand- Sika Topseal 109hi/Fosroc Brushbond RFX/Dr.Fixit Pidifin 2K/MYK Aquafin TG Product Prformance--Chemical Base part A Acrylic Polymer ,Part B ,Specially graded cementitious powder Density -1.6 Kg/l(mixed density) at 27 C .Tensile strength -2N/MM2 After 28 days (with fibre cloth )According to ASTM D2370),Pull out bond strength -2N/mm2(concrete failure )According to ISO 4624 Slant shear bond strength -4N/MM2(According to FIP 5.15)Elongation at break -35% without fibre cloth and 20% with fibre cloth (According to ASTM D2370) d) Protection of treated surface with PCC -The treated surface should be covered with 25mm/50MM PCC of M-20 Grade (1:1.5:3) with proper slope (1:20) towards the rain outlets in alternate pannel of 2mtrx2mtr keeping gap of between the pannel joint .Integral waterproofing admixture confirming to IS 2645 @ 100ML Per Bag of cement to be added in screed concrete (Paid seperately for this item) all corners to be champered with 150mmx150mm fillet .The Rain water oulets shall be just levelled with the screed to ensure smooth discharge of water -The pherperal gaps between PVC pipes oulet and concrete surface to be packed properly with moisture insensitive epoxy putty of Sika India Pvt Ltd/MYK Schomburg/Dr.Fixit/Fosroc.

For purpose of measurement the entire traeted surfaceto be measured. e) Goove of PCC -Surfcae should be filled with polysulphide sealent (paid Seperately) Brand -Sika India Pvt Ltd/MYK Schomburg /Dr.Fixit/Fosroc.Warranty 10 years Covering treated surface with PCC: Providing 50 MM thick cement concrete M20(1;1.5;3) Maintaining slope in alternate pannel 2mtx2mt pannels with approved quality stone chips 20mm to 6mm size graded and sand of F.M.2.5 to 3 including screening,shuttering and mixing cement concrete in mixer with admixture of integral waterproofing and placing position,striking,curing taxes ,loyality all complete as per specification and direction of E/I,Pannels that has been left should be casted next day ,There should be 6mm gap between the Pannels. Brand-Sika plastocrete plus,/MYK Schomburg WP 10 /Dr.Fixit-Pidiproof lw+/Fosroc -Conplast X421IC or equivalent

Providing and mixing integral waterproofing compound in concrete or plaster as per manufacturer specification and as per direction of Eng in charge Brand-Sika plastocrete plus,/MYK Schomburg WP 10 /Dr.Fixit-Pidiproof lw+/Fosroc -Conplast X421IC or equivalent

providing 12 mm thick waterproof cement plaster (1;3) cement :sand of F.M 1.5 With integral waterproofing compound liquid @125ml per bag of cement including screening,curing and all leads,lift of water,scaffolding taxes royalty all complete as per building specification and direction of E/I/ Brand-Sika plastocrete plus,/MYK Schomburg WP 10 /Dr.Fixit-Pidiproof lw+/Fosroc -Conplast X421IC or equivalent

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : (a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours. (b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. (The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.)

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) : 2011 (Board with BIS certification marks)

Providing and fixing GI Clip in MTR.al Ceiling System of 600x600 mm module which includes providing and fixing 'C' wall angle of size 20x30x20 mm made of 0.5 mm thick pre painted steel along the periMTR.er of the room with help of nylon sleeves and wooden screws at 300 mm center to centre, suspending the main C carrier of size 10x38x10 mm made of G.I steel 0.7 mm thick from the soffit with help of soffit cleat 37x27x25x1.6 mm, rawl plugs of size 38x12 mm and C carrier suspension clip and main carrier bracket at 1000 mm c/c. Inverted triangle shaped Spring Tee having height of 24 mm and width of 34 mm made of GI steel 0.45 mm thick is then fixed to the main C carrier and in direction perpendicular to it at 600 mm centers with help of suspension brackets. Wherever the main C carrier and spring T have to join, C carrier and spring T connectors have to be used. including fixing periMTR.er channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the periMTR.er of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and periMTR.er channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound, jointing tapes, finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of periMTR.er channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with: 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- Part I. All sections to be galvanized @ 120 gms/SQM (both side inclusive), fixing with clip in tiles into spring 'T' with: GI MTR.al Ceiling Clip in plain Beveled edge global white color tiles of size 600x600 and 0.5 mm thick with 25 mm height, made of G I sheet having galvanizing of 100 gms/ SQM (both sides inclusive) and 20% perforation area with 1.8 mm dia holes and having NRC of 0.5, electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending and perforation.

Providing and Fixing Baffle Ceiling as per Ditrection of EI

Providing two coats of oil bound distemper of approved shade and make over a coat of cement primer over new surface including preparing the plastered surface by rubbing smooth with pumice stone or fine sand paper, applying putty wherever required, scaffolding, washing of floors and taxes all complete as per building specification and direction of E/l.

Finishing walls with textured exterior paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm sqm

Finishing walls with water proofing cement paint of required shade : 13.44.1 New work (Two or more coats applied @ 3.84 kg/10 sqm)

Providing & laying Wall Art work as direction by EI

Providing wall panelling with 3.5mm thick teak veneered decorative ply wood of standard make fitted and fixed over 50 x 12mm sal wood beads at 122 mm centres properly screwed to walls including cost of spirit polishing over ply wood and 2 coats of wood preservative paint over the beads of approved shade and make all complete as per building specification and direction of E/l.( 4 mm thick ply)

Providing two coats of plastic emulsion paint of approved shade and make over a coat of cement primer over new surface including preparing plastered surface by rubbing smooth with pumice stone or fine sand paper, applying putty wherever required, scaffolding washing of floor and taxes all complete as per building specification and direction of E/l.

Providing two coats of synthetic enamel paint of approved shade and make over steel surface including cleaning the surface thoroughly, scaffolding and taxes all complete as per building specification and direciton of E/l.

Providing two coats of synthetic enamel paint over a coat of primer of approved shade and make over new wooden surface after cleaning, removing dirt, scales, smokes, grease and sand papering, including cost of scaffolding and taxes all complete as per building specfication and direction of E/l.

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work (Two or more coats applied @ 1.43 ltr/10 sqmover and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

Fully Perforated Gypsum Plaster Board of size 1200 x 2400x12.5 mm having approx. 15 % perforated area with perforation size and pattern as approved by the Engineerin- charge and as per manufacturer's specification, with all 4 side tapered and backed by acoustical tissue with NRC value not less than 0.60

Extra for each coat of washing over exterior surface for each consecutive floor above first floor including scaffolding etc. all complete as per direction of E/l.

Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor five level, excluding the cost of centering, shuttering and finishing:1:2:4 (1 Cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size)

ACP Cladding Work

Providing & Laying Acp cladding work on Design Column

SS & Glass Work

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Toughened glass 12 mm thickness for Staircase

STP Work

Providing & Fixing of 1 no of fabricated STP

Water arrangment

Water arrangement for watering garden Area

UPVC Work

Providing and fixing factory made uPVC white colour fixed glazed windows/ventilators comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately). Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. 9.147B.1 Fixed window / ventilator made of (small series) frame 47 x 50 mm & mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area upto 0.75 sqm.)

Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately) Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Three track three panels sliding window with fly proof SS wire mesh (Two nos. glazed & one no. wire mesh panels) made of (small series) frame 92 x 44 mm & sash 32 x 60 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area of window upto 1.75 sqm).

Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with :

5.5 mm thick glass panes

DPC Work

Providing 25 mm thick damp proof course with cement concrete M-150 with nominal mix of (1:2:4) with approved quality of stone chips of 20 mm to 6mm size graded and clean coarse sand of F.M. 2.5 to 3 including, screening, shuttering and mixing cement concrete in mixer with 5% cico or any other approved water proofing compound and placing in position, striking, curing, taxes and royalty all complete as per building specification and direction of E/l.

Providing 25 mm thick damp proof course with cement concrete M-200 with nominal mix of (1:1.5:3) with approved quality of stone chips of 20 mm to 6mm size graded and clean coarse sand of F.M. 2.5 to 3 including, screening, shuttering and mixing cement concrete in mixer with 5% cico or any other approved water proofing compound and placing in position, striking, curing, taxes and royalty all complete as per building specification and direction of E/l.

Expansion Joint Work

Providing and filling in position bitumen mix filler of proportion 80 kg. of hot bitumen, 1 kg. of cement and 0.25 cubic metre of coarse sand for expansion joints. concrete 1:2:4 (1 cement : 2 coarse sand (zone-III): 4 graded stone aggregate 12.5mm nominal size)

Providing and fixing sheet covering over expansion joints with iron screws as per design. Aluminium fluted strips 3.15 mm thick. 150 mm wide

Pre moulded Joint filler, 25 mm thick for expansion joint.

Carriage rates of material by diesel truck (6 MT Capacity) including loading, unloading and stacking on pucca road but excluding contractors profit and overhead charge.

(i) Cement ( 5 Km)

(ii) Sand ( 15 Km)

(iii) Chips ( 25 Km)

(iv) Metal ( 25 Km)

(v) F. Bricks ( 20 Km)

(vi) Reinforcement ( 5 Km)

ELECTRICAL WORKS

S/F MCCB in cubical panel board :- Providing and fixing following rating and capacity 4pole On MCCB in existing cubicle panel board ,including drilling holesin cubicle panel, making connection etc as required.

25/100 amp,16 KA, fixed thermal setting

125 amp,16 KA, fixed thermal setting

315/400 amp,35 KA, fixed thermal setting

500 amp,35 KA,adjustable thermal setting

800 amp,35 KA,adjustable thermal setting

S/F HRC fuse type TP&N switch Disconnector Providing and fixing following capacity double pole TP&N sheet metal switch disconnector fuse switch unit inexisting metal board with ISI marked HRC fuses including drilling holes in metal board , making connections, etc. as required.

800 amps , TP&N, HRC

S/F 'B' series SP MCB: Supplying and fixing 240 volts, 'B' series, miniature circuit breaker suitable for inductive loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc, as required.

6/32 amp singe pole"B" series

S/F 'B' series SP MCB: Supplying and fixing 240 volts, 'B' series, miniature circuit breaker suitable for inductive loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc, as required.

6/32 amps single pole

6/32 amps TPN MCB

50/63 amps TPN MCB

Supplying of PVC /XLPE insulated PVC sheathed, heavy duty,armoured electrical cable with aluminium conductor for working voltage upto and including 1100 volts. (Conforms to IS:1554, part-1)

400 sq mm 3.5 core

300 sq mm 3.5 core

70 sq mm 3.5 core

120 sq mm 3.5 core

25 sq mm 3.5 core

Copper Conductor

2.5 sq.mm 4 core

4 sq.mm 4 core

6 sq.mm 4 core

10 sq.mm 4 core

16 sq.mm 4 core

Laying of one number additional PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of size exceding 120 Sqmm but not exceeding 400 sqmm direct in ground including excavation,sand cusioning, protective covering and refiling the trench etc. as required.

Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of size exceding 95 Sqmm but not exceeding 185 sqmm direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc. as required.

Supplying and making outdoor end termination with cast resin compound including aluminium lugs and other jointing material for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required.

3.5 x 120 sq.mm

3.5 x 300 sq.mm

3.5 x 400 sq.mm

Circuit/Sub-main wiring in PVC Conduit:- Wiring for circuit / sub-main wiring along with earth wire with the following sizes of FR PVC insulated, copper conductor, single core cable in surface/recessed PVC conduit as required.

2x1.5 Sq.mm + 1x1.50 Sq.mm earth wire

2x2.5 Sq.mm + 1x2.5 Sq.mm earth wire

2x4 Sq.mm + 1x4 Sq.mm earth wire

2x6.0 Sq.mm + 1x6.0 Sq.mm earth wire

2x10.0 Sq.mm + 1x6 Sq.mm earth wire

4x2.5 Sq.mm +2x2.5 Sq.mm earth wire

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.

450mm width x 50mm depth x 2.0mm thickness

Power Plug wiring in PVC conduit ( 2 x 4 Sqmm):- Wiring for light / Power plug with 2x 4 Sq. mm FR PVC insulated copper conductor single core cable in surface / recessed PVC conduit along with 1 nos. 4 sq.mm FR PVC insulated copper conductor single core cable for loop earthing as required :-

Earthing with G.I. earth pipe 4.5 m long, 40 MM dia including accessories and providing massonary enclosure with cover plate having locking arrangement and watering pipe etc with charcoal and salt as required

Supply and laying 8 SWG wire at 0.50 meter below ground level for conductor earth electrod ,including soldering etc. as required

Supply and laying 25mm x 5mm G.I strip at 0.50 meter below ground as strip earth electrode, including connection/terminating with G.I. nut, bolt, spring, washer etc. as required.

P/F MV Danger Notice Plate:- Providing and fixing M.V. danger notice plate of 200mmX150mm, made of mild steel at least 2mm thick, and vitreous enamelled white on both sides, and with inscription in the single red colour on front side as required. Details of cost for one each.

P/F HT Danger Notice Plate:- Providing and fixing H.T danger notice plate of 250mmX200mm, made of mild steel at least 2mm thick, and vitreous enamelled white on both sides, and with inscription in the single red colour on front side as required.

1200mm (48") Ceiling fan

12" (300mm) metal exhaust fan

16" (400mm) Wall mounted Fan

ITC Ceiling Fan :- Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (Up to 30 cm) with 1.5 sq. mm. FRPVC insulated,copper conductor,single core cable etc, as required.

S/F Modular type electronic fan regulator: Supplying and fixing stepped type fan regulator on the existing modular plate & switch box including connections but excluding modular plate etc as required.

ITC Exhaust Fan upto 450 mm sweep: installation of exhaust fan upto 450 mm sweep in the existing opening, including making the hole to suit the size of the above fan, making good the damage, including connection, testing, commissioning etc as required.

S/F light plug point with modular type accessories:- Supply and Fixing GI box with modular plate and cover in front on surface or in recess including providing and fixing 3 pin, 5/6 amps modular socket outlet and 5/6 amps modular switch, connection, painting etc as required.

S/F power plug point with modulartype accessories:- Supply and Fixing GI box with modular plate and cover in front on surface or in recess including providing and fixing 6 pin, 15/16 amps modular socket outlet and 15/16 amps modular type switch, connection, painting etc as required.

S/F TP MCB DB: Supplying and fixing following way, horizontal type three pole and neutral sheet MCB distribution board, 415 volts on surface/recess complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required ( But without MCB/RCCB/ ISOLATOR).

4 ways (4+12) Double Door. horizontal type

6 ways (4+18) Double Door. horizontal type

8 ways (4+24) Double Door. horizontal type

S/F Modular type blanking plate :- Supplying and fixing modular blanking plate on existing modular plate and switch box excluding modular plates as required

S/F Modular boxes, base & cover plate :- Supplying and fixing following size/ modules G.I box along with modular base & cover plate for modular switches in receess etc as required.

8/9 MODULE (78MM X 230MM X 60MM)

12 MODULE (135MM X 205MM X 60MM)

4/5 MODULE (78 MM X 140MM X 50MM)

6 MODULE (78MM X 205MM X 50MM)

Point Wiring in PVC Conduit, with Modular type Switch: Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit, with modular type switch, modular plate, suitable size GI box etc as required.

Group- C

Lights

Ceiling Light

Halogen Light

Blossom Light

20/22 W LED Tube Light

12W LED Round Down Light

LED Street Light (45/48 watt)

LED Street Light (70/72watt)

LED Street Light (120 watt)

Supply and errection of galvanised 'D' iron clamp complete with shackle insulator ( 75 mm X 90 mm ), G.I Bolt,nut and washers coach screw etc. as required.

Supply and errection 75mm x 90mm shackel insulator with G.I Bolt ,nut abd strap etc. as required.

Supply and errection of 100 mm x 65 mm pin insulator complete with G.I spindle and nut etc. as required.

Erection of C.C.pole up to 11 m in B.B:- Above 8 metre and upto 11 metre.

11 Mt. height octagonal hot-Dip galvanized pole BOP -1131) with top dia 70 mm bottom dia 175mm& made of 3mm thick sheet base plate dimentions 275 x 275 x 16mm (L x B X T) including suitablesize of foundatin bolt all complete as required.

S/F PVC Conduit:- Supplying and fixing of following sizes of PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed coduit as required.

20 mm PVC Flexible Pipe

20 mm PVC Bends

20 mm four way PVC moulded circular (jn. Box) with lead and screw

Fan Hook

S.P 5/6 amp, one way switch,piano type ISI marked ( 100 Nos.)

S.P 5/6 amp, two way switch,piano type ISI marked ( 100 Nos.)

S.P 15/16 amp, one way switch,piano type ISI marked ( 100 Nos.)

3 pin 5/6 amp, socket outlet,piano type ISI marked(100 Nos.)

6 pin 15/16 amp, socket outlet,piano type ISI marked(100 Nos.)

Transformer 500 kVA 11/0.433 kV:-

Transformer rating 500kVA, 11/0.433kV, Off Circuit,oil cooled, copper wound,transformer and with all accessories as per IS : 2026

DG Set

Supply and installation of 250 KVA DG Set 440 Volts 3 Phase silent diesel generator set with AMF Panel.

Supply and installation of 200 KVA DG Set 440 Volts 3 Phase silent diesel generator set with AMF Panel.

MAIN PANEL

Supply and installation of main panel incomer 800 Amp.

PLUMBING WORKS

EXTERNAL SEWAGE (SOIL , WASTE & RAIN) DRAINAGE SYSTEM

Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS:12818, including hire and labour charges, fittings and accessories etc. All complete, for all depths, as per direction of EIC

200 mm nominal size dia

Construction of masonry Man hole with gully trap in cement mortar 1:4 (1 cement: 4 coarse sand) with RCC top slab with1:1.5:3 mix(1 cement:1.5 coarse and 3 graded stone aggregate 20 mm nominal size ) foundation 1:4:8 mix (1 cement :4 coarse sand: 8 grade stone size 40 mm nominal size in side plastring 12 mm thick with cement mortar 1:3 (1 cement:3 coarse sand)

SW Gully trap 180mm x 150mm

Manhole 455mm x 610 mm with common burnt clay FPS brick of class designation 7.5

Providing and fixing of MS channel gratings for trench of size 450 mm x 600 mm and 5 mm thick. The channel will fix on its frame.

SOIL, WASTE & VENT PIPES, PIPES & FITTINGS.

Building internal drainage system.

Supply fixing and testing UPVC SWR pipe confirming to IS:13592-1992 for waste connection from wash basin and pantry sink to floor trap or thermosyphonage pipe with solvent cement joints including all the fittings laid above the fall ceilling connected in wall etc the shall include wall chiseling making good the same in cement mortar etc complete include with all necessary support like GI hangers support GI grip and bolts GI clamp etc in fall ceilling area as well as supplying and fixing GI slotted angle iron bracket hangers supports with necessary drilling holes to suit the insertion of pipe clamps deburring brick work concrete supports etc as per detailed drawing for supporting soil waste and rain water pipes and water supply pipes in shaft with suitable GI clamps GI bolts anchor nuts and washers fixede on shaft walls outer walls etc.

40 mm dia

80 mm dia

110 mm dia

160 mm dia

Providing and fixing of unplasticised rigid PVC rain water pipes confirming to IS:13592-1992 including jointing with seal ring leaving 10 mm gap between the pipes for thermal expansion.

110 mm dia

Providing & Fixing 150mm dia (through flow perapet grating for rain water Terrace complete as per requirments. (Sample to be approved).

Providing and fixing and testing UPVC floor trap 110mm with SS grating with all necessary UPVC pipes connection extension pipe and reducing tee for wate pipe connections from toilet and wash area.

Providing and fixing and testing UPVC Multi floor trap 110 mm with SS grating with all necessary UPVC pipes connection extension pipe and reducing tee for wate pipe connections from toilet and wash area.all floor trap should be 70mm water seal .

Providing and fixing and testing UPVC Nahani trap 110 mm with SS grating with all necessary UPVC pipes connection extension pipe and reducing tee for wate pipe connections from tiolet and wash area.all floor trap should be 70mm water seal .

BUILDING WATER SUPPLY SYSTEM (INTERNAL & EXTERNAL)

Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes confirming to IS:15801, UV stabilized & anti - microbial fusion welded, having thermal stability for hot & cold water supply, including all PP - R plain & brass threaded polypropylene random fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-Charge. Concealed work,including cutting chases and making good the wall etc

20mm outer dia

25mm outer dia

32mm outer dia

40mm outer dia

50mm outer dia

63mm outer dia

Providing and fixing PPR Unions

PPR Union 20 mm

PPR Union 25 mm

PPR Union 32 mm

PPR Union 40 mm

PPR Union 50 mm

PPR Union 63 mm

Providing & Fixing gun metal gate valve with C.I. Wheel of approved quality (screwed end)

20mm nominal bore

25mm nominal bore

65mm nominal bore

Providing & Fixing C.P. Brass stop cock (Concealed) of standard design and of approved make conforming to IS:8931

15mm nominal bore

S.C.I. Soil, waste and vent single socketed pipe 1.8 m long

100mm outer dia

Providing and fixing of individual 5 star Electrical water heater for individual toilet the heater will be EPAC(Engineered polymer anti corrosive )coated on its inner tank to suit any kind of water withstanding pressure capcity 8kg/cm2 .

PLANT ROOM(PUMP ROOM,)

DOMESTIC WATER SUPLY PUMP Set

SUPPLY, INSTALLATION, TESTING & COMMISSIONING, OF COMPACT SELF CONTENED SKID WATER TRANSFER SYSTEM AS FOLLOWS:

PURPOSE:DOMESTIC

(a) Horizontal splte case CENTIFUGALWATER TRANSFER PUMP WITH WITH SUITABLE TEFC SQUIRREL CAGE INDUCTION MOTOR WORKING ON SINGLE PHASESUITABLE PHASE CONNECTIN 50HZ ± 3%, 10% ALONG WITH BASE FRAME, COUPLINGGUARD,MS BASE FOUNDATION AND BOLT ETC. COMPLETE Set AS PER RELEVENT IS AND FOLLOWING MOC Pump casing :Cast iron Pump Shaft : Stainless steel bronze Impellers :,

WATER TRANSFER PUMP

NOS OF PUMP :

WATER FLOW RATE : TRANSFER PUMP 3 L/S, 1.5kg/cm2/ @30 MTR HEAD.

(a) IN- LINE, VERTICAL SUBMESIBLE SUMP PUMP, WITH SUITABLE SUITABLE PHASE CONNECTIN 50HZ ± 3%, 10% COMPLETE Set AS PER RELEVENT IS AND FOLLOWING MOCPump Housing : Stainless Steel Pump Shaft : Stainless Steel Suction Bracket : Stainless Steel Discharge Nozzle : Stainless Steel Stage Bowl : Stainless Steel Impellers : Noryl Diffusers : Noryl Strainer : Stainless Steel ,

WATER TRANSFER PUMP

NOS OF PUMP :

WATER FLOW RATE :4 LPS

HEAD:18 M

(b)HORIZONTAL,CENTIFUGAL BOOSTER PUMP WITH SUITABLE TEFC SQUIRREL CAGE INDUCTION MOTOR WORKING ON SINGLE PHASE 50HZ ± 3%, 415 ± 10% ALONG WITH BASE FRAME, COUPLINGGUARD,FOUNDATION BOLT ETC. COMPLETE Set AS PER RELEVENT IS AND FOLLOWING MOC,IMPELLAR AND WEARING RING-SS SHAFT WITH SLEEVES-SS,CASING-CI,BASE FRAME-MS.

NOS OF PUMP : 2 (1 NO WORKING + 1 NO STAND BY)

WATER FLOW RATE :2.5 LPS 1.5 bar pressure

HEAD:30 M

PURPOSE:DOMESTIC

(C ) COMPLETE SKID MOUNTED ELECTRICAL CONTROL PANELFOR WATER TRANSFER PUMP COMPRISING OF ALL ACCESSORIES SUCH AS RELAY STARTER INDICATING LAMT VOLT AMP METER PUSH BUTTON WIRING AND ANY OTHER NECESSARY ACCESSORIES, ETC. (LIST TO BE PROVIDED BY THE CONTRACTOR). PUMPS SHALL HAVE DRY RUN PROTECTION & HIGH /LOW LEVEL ALARM.EACH PUMPS SHALL HAVE STARTERS.

(D) COMPLETE SKID MOUNTED ELECTRICAL CONTROL PANEL FOR BOOSTER PUMP COMPRISING OF ALL ACCESSORIES SUCH AS RELAY STARTER INDICATING LAMT VOLT AMP METER PUSH BUTTON WIRING AND ANY OTHER NECESSARY ACCESSORIES, ETC. (LIST TO BE PROVIDED BY THE CONTRACTOR). PUMPS SHALL HAVE DRY RUN PROTECTION & HIGH /LOW LEVEL ALARM.EACH PUMPS SHALL HAVE STARTERS.

(D) COMPLETE SKID MOUNTED ELECTRICAL CONTROL PANEL FOR SUBMESIBLE SUMP PUMP COMPRISING OF ALL ACCESSORIES SUCH AS RELAY STARTER INDICATING LAMT VOLT AMP METER PUSH BUTTON WIRING AND ANY OTHER NECESSARY ACCESSORIES, ETC. (LIST TO BE PROVIDED BY THE CONTRACTOR). PUMPS SHALL HAVE DRY RUN PROTECTION & HIGH /LOW LEVEL ALARM.EACH PUMPS SHALL HAVE STARTERS.

Providing & Fixing gun metal gate valve with C.I. Wheel of approved quality (screwed end)

65mm nominal bore

50mm nominal bore

SUPPLYING, INSTALLING, TESTING & COMMISSIONING CI NON RETURN VALVE AS PER IS 5312 WITH NECESSARY CONNECTING FITTING LIKE FLANGES, NUTS AND BOLTS ETC.

50mm Dia

SUPPLYING, INSTALLING, TESTING & COMMISSIONING CASTE IRON Y STRAINER WITH NECSSARY CONNECTING FITTING LIKE FLANGES NUTS AND BOLTS ETC

65mm Dia

SUPPLYING,INSTALLING,TESTING & COMMISSIONING CAPACITIVE TYPES LEVEL CONTROLLER CONSISTING OF LEVEL FLOAT SWITCH SIDE MOUNTED OR TOP MOUNTED AS PER DETAILS DESIGN STILLING PIPES CABLES FOR RAW WATER TANKS, FLUSHING WATER TANK PUMPS & OVERHEAD WATER TANK ETC.

SUPPLYING,INSTALLING,TESTING & COMMISSIONING CAPACITIVE TYPES LEVEL CONTROLLER CONSISTING OF MECHANICAL FLOAT VALVE SIDE MOUNTED OR TOP MOUNTED AS PER DETAILS FOR ROOF WATER TANK.

SANITARY FIXTURES

Providing and fixing white vitreous china pedestal type water cloSet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required :

Supply installation testing and comissioning Health faucet with adequate length CP or SS hose pipe including connectors adeptors GI nut bolts washer check nuts CP brass two in one bib tap including necessary sleeves flanges cock angle valve and all other fittings accessories required for satisfactory installation.

Metropole Flush Valve Regular 32mm Size (Concealed Body) with Exposed Shut off provision & Round flange.

Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required :

Single half stall urinal with 5 litre P.V.C. automatic flushing cistern

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require

White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar tap

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931

15mm outer dia

Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge.

Providing and fixing CP soap holder concealed fittings arrangement with adequete weight.

Providing and fixing CP towel ring tapezoidel and shape of approved quality and colour .

Providing and fixing CP coat hook according to approved quality and colour.

Providing and fixing liquid soap holder container 109mm wide 125mm high and 112mm distance from wall standard shape with bracket with same materials with snap fittings.

Providing and fixing of CP toilet paper holder inclusive all accessories complete.

Providing and fixing Pillar cock with all fittings and accessories.

Providing & Fixing 15mm C.P. brass mixing fitting for shower with swinging spout complete, including cutting & making good the walls wherever required. Wall mixer with swivel spout.

Providing and fixing Anodized Aluminium Structue 3 Adjustable Vertical Jets(Round) ,Integrated Shower Head (8" Round) Thermostatic Mixer With Diverter, Hand Shower With Flexible Hose button Spout connectiong hose.

Providing and fixing stainless steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. Brackets and SS plugs 40 mm, including painting and fittings and brackets, cutting and making good the walls wherever required

Kitchen sink with drain board

510 x 1040 mm bowl depth 25 mm

HVAC WORKS

OUTDOOR UNIT

32 HP WITH INVERTER SCROLL

20HP WITH INVERTER SCROLL

VRV OUTDOOR UNIT

Ductable Type:- SUPPLY OF DUCTED TYPE INDOOR UNIT indoorunit should be of Ductable type complete with blower section with motor driver,evoporator, EEV(electronic expansion valve).filter etc with low Noise level.

5 TR UNITS WITH MINIMUM

4 TR UNITS WITH MINIMUM

8 TR UNITS WITH MINIMUM

VRV CASSETTE UNIT

4 TR UNITS WITH MINIMUM

REFNET CONNECTION

REMOTE

Refrigerant Copper Piping

Hard Drawn Cu Refrigent Piping For Suction/Liquid Line Including Nitrile Rubber Insulation

41.3 mm O.D.(insulation : 19 mm)

34.9 mm O.D.(insulation : 19 mm)

28.6 mm O.D.(insulation : 19 mm)

22.2 mm O.D.(insulation : 19 mm)

19.1 mm O.D.(insulation : 19 mm)

15.9 mm O.D.(insulation : 19 mm)

12.7 mm O.D.(insulation : 19 mm)

9.5 mm O.D.(insulation : 13 mm)

PVC Drain Piping :- Supply & Fixing Of hard drawn Pvc Drain Piping Complete with fittings ,Supports,along with 6 mm thick closed cell elastomeric insulation

Supply & Laying ,testing and commissioning of Microprocessor Based interconnecting communication cable from indoor to outdoor enclosed with hard pvc conducted with necessery support

Control cable 2C X 1.0 Sq mm for VRF Unit

Supply, installation, balancing and commissioning of factory fabricated GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required

Thickness 0.63 mm sheet (GSS)

Supply/Return Air Grills

Supplying & fixing of powder coated extruded aluminium Supply Air Grills with aluminium volume control dampers as per specifications

Supplying & fixing of powder coated extruded aluminium Return Air Grills with louvers but without volume control dampers complete as required.

Supplying and fixing of following thickness duly laminated aluminum foil of mat finish closed cell Nitrile rubber (class“O”) insulation on existing duct after applying Suitable adhesive for nitrile rubber. The joints shall sealed with 50 mm wide and 3 mm thick self adhesive nitrile rubber tape insulation complete as per specifications and as required.

13 mm thick (In Condition Space)

Supply of 2C x 1.5 sq.mm. Grande with Copper Conductor Armored Fire Survival Cable with ERP Insulation

FIRE FIGHTING WORKS

Supply, Installation, Testing and Commissioning of electric driven, horizontal type, single/multistage, end suction type, centrifugal pump of cast iron body, C.I impallers with carbon steel shaft & mechanical seal directely coupled with TEFC SQ cage foot mounted type induction motors suiitable for operation on 3 phase, 415 volts 50 Hz AC supply having flow rate of min 450 LPM and head of approx 40 mtrs complete in all respect as required or as directed by engineer incharge.

Main Fire Pump

Standby Deisel Engine Pump

Jockey Pump

Terrace Booster Pump

Fabrication, Supplying, Installation, Testing & Commissioning of electrical control panel of cubical construction, wall mounted type, fabricated out of 2mm. thick CRCA sheet, compartmentalised with hinged lockable doors, dust and vermin proof, powder coated of approved shade after 7 tank treatment process, cable alley, interconnection, and accessories mounting and internal wiring, earth terminals, numbering etc. complete in all respects, suitable for operation on 415 V, 3 phase 50 HZ AC supply with enclosure protection class IP 42.

For Pump Room

For Terrace Pump

Supply and fixing of PVC sheathed following conductor 1.1 KV grade armoured Cable of following sizes including making end termination with compression gland & bimetalic lugs, and support etc.complete as required

3 × 50 sq.mm.(aluminium)

3 × 10 sq.mm.(aluminium)

10 × 2.5 sq.mm.(Copper)

2 × 1.5 sq.mm. in Conduit

Providing and fixing IS marked Gate Valve / Foot Valve (incase of -ve suction) complete with companion flanges, bolts, nuts, rubber insetions etc.

150 mm diameter

100 mm diameter

Providing and fixing IS marked butterfly valve (PN 1.6) complete with companion flanges, bolts, nuts, rubber insetions etc.

80 mm diameter

100 mm diameter

150 mm diameter

Providing and fixing check valve (NRV) complete with companion flanges, bolts, nuts, rubber insetions etc.

80 mm diameter

100 mm diameter

150 mm diameter

Pressure Gauge Assemble with Gate/Ball Valve

Providing & fixing of pressure switch in M.S. pipe line including connection etc. as required.

Air release Valve / Drain Valve

MS Structure support for piping

Providing, laying, testing & commissioning of IS 1239 marked black M.S pipe including all fittings i.e bend, elbows, tees, flanges, reducing socket, nuts and bolts, gaskets etc fixed with welded / screwed joints. including necessary excavation, backfilling, removal of surplus soil etc. min. 1 mtr deep excavation and wrapping with anticorrosive treatement with 4 mm thick asphalt tape as per IS:10221, refilling the trench etc. OR fixed with screwed or welded joints, hanged with clamps, hanger supports, dash fasteners, bolts, nuts, rubber insertions etc including threading, cutting, welding, edge preparation, painting of approved colour over two coat of primer, cutting & making good the wall/ floor wherever required, complete as required or as directed by engineer incharge.

150 mm diameter

100 mm diameter

80 mm diameter

65 mm diameter

50 mm diameter

40 mm diameter

32 mm diameter

25 mm diameter

Providing and fixing S.S Fire Hydrant Valve of approved quality with 63 mm female, instant, ovlique, single outlet, 80 mm flanged inlet, brass spindle, cast iron wheel m A.B.S. blank cap and chain. conforming to IS: 5290 complete with companion flange, bolts, nuts, rubber insertion / compressed asbestos gasket etc. and painted in fire red colour.

Providing and fixing swinging, wall mounting type First Aid Hose Reel of approved quality and made from compresed steel sheet with dust cover, cast iron brackets including 30 m long, 19 mm nominal bore, high presure braided rubber hose as per IS:444 Type hose guide, PVC shut off nozzle with 6 mm outlet and 25 mm nominal bore gun metal inlet valve, bolts, nuts rubber insetion etc. painted in Fire red colour including cutting and making good the walls wherver required.

Providing and fixing 25 mm nominal gun metal gate valve class I with CI wheel of approved quality with union (Screwed end)

Providing and fixing in position 63 mm nominal bore and 15 m long synthetic fibre, CP fire hose pipe of approved make bearing IS: 636 -1988 type A mark and having TAC and MMD approved with a pair of 63 x 63 mm gun metal instantaneous type, heavy duty delivery hose coupling (conforming to IS: 903) bound and riveted to the hose pipe with copper rivets and copper wire complete.

Providing and fixing in position short SS brach pipe of approved quality with 63 mm male instatneous type inlet and 15 mm outlet nozzle complete conforming to IS : 903

Supplying and fixing of hose cabinet of size 450mm x 450mm x 250mm made of 2mm thick M.S. sheet with 6mm thick glazed glass door including necessary locking arrangment suitable to accomodate 1 nos. 15 mtr. long hose pipe, 1 no. branch pipe mounted on wall or raised brick platform and duly painted with post office red externally and white internally with synthetic enamel paint complete in all respect.

Providing and fixing Standard response Upright / Pendant sprinklers (With Covers, white / ivory colour) with quartzoid bulb overating temperature 68 degree centgrade, of 15 mm orifice and k factor 80 (5,6) made out of forged brass and chrome finish.

Supplying, installation, testing & commissioning of sprinkler flexible pipe of stainless steel complete with 15 NPT on reducer thread with maximum working pressure of 175 PSI test pressure of 875 PSI (Burst) with branch line (Inlet) 25mm NPT male thread to sprinkler head (Outlet) 15mm NPT female thread with reducer, nipple, 2 side brackets, center bracket, stockbar of following sizes complete as required.

Supplying, fixing, testing & commissioning of 1 set of 63mm two way instantaneous fire brigade connection (FBC) with inbuilt NRV comprising of SS and four SS instantaneous male inlet coupling confirming to IS:604 with plug and cap with chain as required with nut & bolts, washers, high pressure gasket as required.

Providing , fixing Dry Chemical Powder (Stored Pressure Type) Mono Ammonium Phosphate 50% powder confirming to ‘IS 14609’ , Nitrogen Pressurized, Controllable Discharge Mechanism, Pressure Gauge, Discharge Hose & Nozzle Epoxy Polyester Powder Coated As per ‘IS 15683’ ISI mark Fire Extinguishers. Operating Temperature: - (-) 20oC to (+) 55oC Suitable for ‘A’ ‘B’ ‘C’ Class of FIRE complete in all respects (4 Kg Capacity)

Carbon Di-oxide Type , Gas Confirming to IS ‘15222’ , Cylinder Confirming to ‘IS 7285’ & PESO approved ,Controllable Discharge Mechanism, Discharge Hose & Horn As per ‘IS 15683’ & ‘IS 2878’ ISI mark Fire Extinguishers (Wheel Type or Squeeze Grip Type). Operating Temperature :- (-)20oC to (+)55oC Suitable for ‘B’ ‘C’ Class of FIRE (4.5 Kg Capacity)

Providing , fixing Modular type Fire Extinguishers for electrical rooms (Stored Pressure Type) Mono Ammonium Phosphate 50% powder confirming to ‘IS 14609’ , Nitrogen Pressurized, Controllable Discharge Mechanism, Pressure Gauge, Discharge Hose & Nozzle Epoxy Polyester Powder Coated As per ‘IS 15683’ ISI mark Fire Extinguishers. Operating Temperature: - (-) 10oC to (+) 55oC Suitable for ‘A’ ‘B’ ‘C’ Class of FIRE complete in all respects (5 Kg Capacity)

Supplying, installation, testing and commissioning of optical type Smoke detector and mounting base with LED light complete as required.

Supplying, installation, testing & commissioning of response indicator on surface/recessed having two LED with cover complete with all connections etc as required

Supplying, installation, testing and commissioning of duel tone electronic hooter / Flasher / Strobe suitable for wall mounted complete as required.

Supplying, installation, testing and commissioning of manual call box in suitable enclosure with arrangement to raise the alarm when the glass is manually broken complete as required.

Supplying, installation, testing and commissioning of microprocess base main fire alarm control panel with LCD Display lights. The panels shall have 240 volts AC power supply automatic Battery charger 24 Volts sealed lead acid maintenance free battries as complete with batteries, battery charger illuminated numeric digram complete as required.

Providing and laying 19mm dia PVC conduit complete with required junction boxes in recessed / surface system PVC insulated copper conductor cable of 2x1.5 sq.mm. in existing conduit as required.

FIRE ALARM SYSTEM (ADDRESSABLE TYPE)-

Supply, Installation , Testing & Commissioning of Microprocessor based (1 +1 Hot reduntant) panel , Networkable analogue addressable type single cabinet fire alarm control panel with 240 X 64 pixel graphic LCD display with atleast 6 lines of information with minimum history of 2 X 5000 event. The panel shall be equipped with sufficient numbers of loop with 10-20% spare capacity with each loop and shall have a capacity of 240 any combination of analogue detector or devices in one loop. The panel shall have dedicated control for controlling of dampers, smoke curtains, AHUs, pressurization fans, ventilation fans at fire pump room, monitoring of fire sprinkler and fire hydrant pump, 240 volts AC power supply, automatic battery charger, 24 volts sealed lead acid batteries sufficient for 24 hours normal working conditions as required in EN standard and respective NBC. The Panel shall have BACKNET & MODBUS CARD integration with voice evacuation and fire fighting telephone system. The complete panel assembly shall come with 1+1 hot redundancy at all level loop cards, CPU, network card, display, power supply as well as shall have integrated voice evacuation and fire fighting telephone system. Panel shall be EN complied , VDS & FM approved. The panel in itself shall be EN complied with no additional hardware. Make : Autronica Utc/Hampton/Gamewell

Supply, Installation , Testing & Commissioning of Automatic Analog addressable EN complied & VDS approved Smoke detector, having bidirectional fault Isolators((one for incoming and one for outgoing line) integrated in detector for maintaining operational availability of all elements in the loop, even in the event of a short circuit & detector shall have sensitivity as automatic drift compensation type at variable environment, with mounting based LED, Address Switch / electronic address to programme the detectors, complete as required. Make : Autronica Utc/Hampton/Gamewell

Supply, Installation , Testing & Commissioning of Automatic Analog addressable EN complied & VDS approved Heat detector, having bidirectional fault Isolators((one for incoming and one for outgoing line) integrated in detector for maintaining operational availability of all elements in the loop, even in the event of a short circuit & detector shall have sensitivity as automatic drift compensation type at variable environment, with mounting based LED, Address Switch / electronic address to programme the detectors, complete as required. Make : Autronica Utc/Hampton/Gamewell

Supply, Installation, Testing and Commissioning of Beam Detector. The beam detector shall be used for High Ceiling application with a detection range upto 70 mtrs sensitive settings. Make : Autronica Utc/Hampton/Gamewell

Supply Installation, Testing & Commissioning of Addressable EN54-17 complied & VDS approved control relay modules for output signal of party unit.The module shall have inbuilt fault isolator. Make : Autronica Utc/Hampton/Gamewell

Supply Installation, Testing & Commissioning of Addressable EN54-17 complied & VDS approved monitor modules with inbuilt fault isolator for Sprinkler Flow Switch & LHS cable Monitoring etc as required. Make : Autronica Utc/Hampton/Gamewell

Supply, Installation , Testing & Commissioning of Response Indicator which consists of steady glowing LED. This LED shall be mounted within a box and connected in parallel to the built in indicator of the detector as per specifications. The RI shall come "ON" as soon as the detector activates complete in all respects as per specification. Make : Autronica Utc/Hampton/Gamewell

Supply, Installation , Testing & Commissioning of Addressable type EN54 complied & VDS approved addressable manual call (pull type) Station with inbuilt fault isolator complete with all accessories as per specifications. Make : Autronica Utc/Hampton/Gamewell

Supply, Installation, Testing & Commissioning of EN54-17 complied & VDS approved loop powered addressable Sounders cum flasher with inbuilt fault isolator base at 90-100db .to notify Occupants for fast & safe Evacuation as specified. Make : Autronica Utc/Hampton/Gamewell

Supplying and installation of Exit Signs: photo luminescent safety signage made up of photo luminescent material of rare earth aluminates, non radioactive working on the principle of high processed on 1.2 mm thick aluminum sheet including arrangement for fixing on wall / ceiling etc. complete as required (single sided) (size 150 mm x 300 mm)

Supplying and fixing of following sizes of STEEL conduit alonwith the accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required.

20mm dia

25mm dia

32mm dia

Supplying and drawing of following sizes of Low Smoke Zero Halogen Silicon Insulated Fire Survival Cable with Drain Wire, solid copper conducter cable approved by LPCB as per BSEN 50200:2015 PH 120 (Fire, Mech Shock & Water 120 Minutes @ 830 deg Celcius, Fire & Mech Shock every 5 Min for 2 Hours- Both test conducted on same sample) and BS-6387 CWZ The cable shall sustain 950 deg. C. The cable shall be approved for. The cable shall be BS EN 60332-1-2:2004 for Bunched Flame Retardancy (installed as a single or bunched cable self extinguishes leaving the upper cable sheath unaffected showing the cable does not propagate fire). Cable shall be guaranteed for 10 years from the date of manufacture marked on the cable. 2 X 1.5 sq. mm Make:Noburn/Lapp/Wrexham

Panel Flooding System

For Electrical Enclosure 1 X 3 Kg Novec 1230, LPCB/UL/FM approved for Enclosed and Ventilated (Natural and Forced Airflow) Electrical Panels, Direct Discharge complete system consisting of DLP Assembly with automatic valve, 40 mtr linear pneumatic heat detection tube, push in connector for tube, 3 Kg Novec 1230 gas, mounting bracket, End of Line adopter , low pressure switch & master control unit for monitoring system activation. The cylinder made of mild steel TPED approved along with sturdy metal bracket having direct low pressure dual discharge valve having safety brust disc for over pressurization and ball valve with open and closed option. The clean agent Novec 1230 to be filled in approved filling plant. The DLP valve having push in connector for tube to be connected with double push mechanism.The heart of the system linear heat sensing tube made of special polymer red colour 4mm I.D. 6mm O.D. pressurized with Nitrogen to be installed as per the OEM Manual. All the tube fittings to be OEM supplied.

For Electrical Enclosure 1 X 3 Kg Novec 1230, LPCB/UL/FM approved for Enclosed and Ventilated (Natural and Forced Airflow) Electrical Panels, Direct Discharge complete system consisting of DLP Assembly with automatic valve, 30 mtr linear pneumatic heat detection tube, push in connector for tube, 3 Kg Novec 1230 gas, mounting bracket, End of Line adopter , low pressure switch & master control unit for monitoring system activation. The cylinder made of mild steel TPED approved along with sturdy metal bracket having direct low pressure dual discharge valve having safety brust disc for over pressurization and ball valve with open and closed option. The clean agent Novec 1230 to be filled in approved filling plant. The DLP valve having push in connector for tube to be connected with double push mechanism.The heart of the system linear heat sensing tube made of special polymer red colour 4mm I.D. 6mm O.D. pressurized with Nitrogen to be installed as per the OEM Manual. All the tube fittings to be OEM supplied.

Total Room flooding system (For Main CCTV Room & AV Room) - 1x40 Itr completele CCOE approved high pressure seamless BIS 7285 approved Cylinders having 40 ltr capacity, UL/FM/VDS approved FK5-1-12 clean agent gas with UL/FM/VDS listed valve assembly and electric solenoid switch. The system also to be fitted with low pressure supervisory switch for monitoring cylinder pressure gauge with safety burst disc safety cap, elbow and other accessories, mounting bracket, container straps, NRV , Pressure operated control head which shall allow for pressure actuation of gas mounted, manually operated actuator to actuate the gas flooding process with the help of a lever, flexible rubber hose with wire bralded enforcment to route the gas from the storage cyinder to the discharge piping, to be connected to the discharge outlet of gas cylinder valve & to be terminated at the system piping or discharge manifold, Flexible actuation hose complete as required. Discharge nozzle, 180/360 degree. Designated to provide proper flow rate & distribution FK5-1-12 gas to flood the hazard area as per latest NFPA 2001 requrement. Piping ASTM grade A 106 schedule 40 with fittings & supports and Gas Release Panel compatible to Fire Alarm System. Makes : Firetrex, Tracefire, Safefire

CCTV WORKS

Supplying, installing, testing and commissioning of Dome camera 1/2.8" CMOS, F1.6~F3.3, Fixed Iris, 120dB, 50m IR, 0.001Lux, 1920x1080@30fps, 512 GB SD card slot, IP67, IK10, PoE, Built-in Mic, Audio 1/1, Alarm 2/1, Reset button, Smart VCA function, Face capture mode, Full Metal Housing

Supplying, installing, testing and commissioning of Bullet camera 1/2.8" CMOS, F1.6~F3.3, Fixed Iris, 120dB, 80m IR, 0.001Lux, 2592x1944@30fps, 2MP@60fps, 512 GB SD card slot, IP67, PoE, Built-in Mic, Audio 1/1, Alarm 2/1, Reset button, Smart VCA function, Face capture mode, Full Metal Housing.

Supplying, installing, testing and commissioning of 64Ch, 320Mbps/320Mbps, recording resolution up to 12MP, decoding ability 4*8MP, 16*1080p, 32*720p, video output: 2 HDMI & 2VGA non-simultaneous output, alarm I/O 16/4, USB interface: 1xUSB 3.0 2xUSB 2.0, RAID: JBOD,RAID0/1/5/6/10, ANR, N+M

Supply, Installation, Testing & Commissioning of 43" Commercial display built in Android OS.

Supply, Installation, Testing & Commissioning of 42U Rack including all accessories as complete as required.

Supply, Installation, Testing & Commissioning of 12U Rack including all accessories as complete as required.

Supply, Installation, Testing & Commissioning of CAT-6 Patch Cord, 4 Feet : CAT6 UTP 23 AWG Patch Cord - 1 mtr - Factory crimped LCS2 Patch cord in Blue colour.

Supply, Installation, Testing & Commissioning of CAT-6 Patch Cord,SITC of 7 Feet : CAT6 UTP 23 AWG Patch Cord - 2 mtr - Factory crimped LCS2 Patch cord in Blue colour

Supplying, installing, testing and commissioning of 24 port Cat 6 patch panels available with block of four equipped with tool less IO, Rack Mountable. 19" Modular Patch Panel, loaded CAT6 U/UTP 24 port LCS2 rack mountable to be compatible in 4nos of 6 X RJ 45 Tool less connector U/UTP unit in a block. Make:- Legrand/Systimax/Scheinder

Supply ,Installation, Testing & Commissioning of Server Grade Machine with Minimum 3 Ghz Processor, 8GB RAM, 1 TB Hard disk along with necessary as required.

Supply of Surveillance Hard Disc Drive 6TB

Supply, Installation, Testing and Commissioning of 24 PoE 10/100/1000 BaseT, 2 SFP+ 1G/10G ports, one expansion slot. Includes an internal 390W PoE PSU, power cord, manuals access card, RJ-45 to DB-9 adaptor.

Supplying and fixing of following sizes of STEEL conduit alonwith the accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required.

20mm dia

25mm dia

32mm dia

Supply and drawing of UTP 4 pair 23 AWG CAT 6 LAN Cable in the existing surface/ recessed steel/ PVC conduit as required. 4 Pair CAT6 Unshielded, Twisted Pair (U/UTP) Cable. Blue/Orange/White/Green in colour conforming to the following standards like ANSI/TIA 568 C.2, EN50173, IEC 11801 2nd ED, frequency tested upto 700Mhz with Third Party Certificate etc.

AUDIO-VISUAL SYSTEM & ALLIED SERVICES

First Floor Meeting Room

Gooseneck Microphone for Chairman Unit & Delegate Unit. Microphone Type Electret Cardioid Frequency Response 50 Hz – 17 kHz Sensitivity –46 dB ± 3dB (0 dB = 1 V/1 Pa, 1 kHz) Maximum SPL 110 dB SPL (3% THD) Signal to Noise Ratio >60 dBA Front/Back Ratio >25 dB (1 kHz) Power Requirements 2–5 Volts DC Supplied from Conference Unit Power Consumption 10 mA (typical) Connectors Connector Type 3 pin male

Central Controller Unit, ●Fully digital distribution of the main “floor” audio plus 31 interpretation channels over a single shielded CAT5e network cable ●Support for up to 250 participants; up to 3,800 participants with optional feature licenses ●Enables up to 8 active microphones, controlled by participants or chairman/technician ●Multi-language web browser for system configuration, microphone control, and name/seat assignment via tablet or computer ●4 DCS-LAN chain connections; 2 analog audio inputs; 8 analog audio outputs Compatible with Extension Unit, Junction Box, Repeater and Power Kit for additional power or cabling flexibility in larger installations

POWER SUPPLY UNIT FOR DIS Main voltage 100-240 V, 50-60 Hz nominal Max. consumption 175 W Total supply power 144 W (power factor: >0.9) Standby consumption - <0.5 w (no load) Supply voltage 48V/3A @ 40°C[1] Efficiency 87%, typical Inrush Current •230 V:<80 Amp; 115V:<40 Amp

CABLE (20 Mtrs) length for connections Electrical Delay Skew (Maximum) less than 25 nanosecond/100 m Cable Rating CAT5e - 350 MHz Impedance 100 ± 15 ohms Return Loss (Minimum) 18.9 dB at 100 MHz Mechanical Conductor Gauge 24AWG Number of Conductors 4 pair F/UTP Cable Jacket Type PVC-Polyvinyl Chloride Color Black Cable Type Shielded Snag-less Construction PVC jacket, ripcord, foam polypropylene insulation, aluminum/polyester shield with drain wire Construction Plenum Plenum polymer alloy jacket, ripcord, FEP insulation, aluminum/polyester shield with drain wire Fire Rating CMG Rated (General Purpose) Wiring Type TIA/EIA-T568-B Connectors RJ-45 Male

CABLE (3 Mtrs) length for connections Electrical Delay Skew (Maximum) less than 25 nanosecond/100 m Cable Rating CAT5e - 350 MHz Impedance 100 ± 15 ohms Return Loss (Minimum) 18.9 dB at 100 MHz Mechanical Conductor Gauge 24AWG Number of Conductors 4 pair F/UTP Cable Jacket Type PVC-Polyvinyl Chloride Color Black Cable Type Shielded Snag-less Construction PVC jacket, ripcord, foam polypropylene insulation, aluminum/polyester shield with drain wire Construction Plenum Plenum polymer alloy jacket, ripcord, FEP insulation, aluminum/polyester shield with drain wire Fire Rating CMG Rated (General Purpose) Wiring Type TIA/EIA-T568-B Connectors RJ-45 Male

Redudancy Interface Box FEATURES • Enables redundant loop DCS-LAN cabling for greater system reliability • Small size for convenient in-line placement • Passive; no power required • Compatible with series conference units

Zonal Announcement System

20 zone announcement system (one way), consisting 20 zone console with in built Gooseneck microphone, suitable amplifier and 20 nos (6 nos in Ground Floor and 12 nos in First Floor) compatible speaker for the same. Zonal Announcement System Great performance PA microphone for live vocal & music. Hardened grille with anti-roll rubber ring. Supplied with quick detachable holder with 3-pin professional XLR connector & 10 mtrs. twin core shielded low noise cable. Freq. Response – 50-18,000Hz. Sensitivity – 2.1mV/Pa. Impedence - 300Ω

Cables, Mic. Stands, Speaker brackets, speaker cables, Interconnecting, Cables, storing and operating rack, clamps and other allied items.

Multipurpose Hall

Compact High definition passive Loud Speaker, Rec Amplifier 480 - 720W Nom. Impedance 8 ohm Frequency Response 70Hz - 18kHz Max SPL 130dB Directivity Asymmetric +15/-45 vertical, 30/60 horizontal Woofer 10” Neodymium Woofer Tweeter 3” Neo Compression Driver (1.4” Exit) Connections & Wiring 2x Speakon 1+/- Dimensions 641.5 x 306 x 352mm Weight 16.4kg net

Compact 18” passive Sub-Bass Loud speaker. Rec Amplifier 800-1200W Nom. Impedance 8 ohm Frequency Response 38Hz - 160Hz Max SPL 129dB Woofer Custom Designed 18" Ferrite Connections & Wiring 2x Speakon 1+/- Dimensions 900 x 520 x 474mm Weight 40kg

Concelable passive Sub-Woofer, Max SPL *calculated - 118dBSPL Sensitivity 1W @ 1m - 60Hz – 96dB Frequency Response - -9dB 44Hz ? 90Hz Impedence - 8Ω Power Handling – 300W RMS Driver - 10" 50mm Voice Coil Dual Spider, Dual Magnet Woofer. Connectivity - Captive Screw Terminal Plug (In/Thru) Dimension - 500 x 470 x 215mm Net Weight – 15.1 kg

Full frequency range multi-purpose 2 way passive speaker system– Surround speakers. Rec Amplifier 320 - 500W Nom. Impedance 8 ohm Frequency Response 75Hz - 19kHz Max SPL 119dB Directivity Asymmetric +15/-45 Vertical, 45/90 Horizontal Woofer 8” High Powered Woofer Tweeter 1” Ferrite Compression Driver Connections & Wiring 2x Speakon 1+/- Dimensions 449 x 250 x 250mm Weight 8.9kg net

Passive stage Monitor Speaker, Model QM 12 MP (Left & Right) Power Handling (Nominal) 500W RMS Frequency Response +/- 3dB 65 - 19 KHz Maximum SPL @1m 128dB Impedance 8 ohms Connections Speakon NL4 x 2 In/out Wiring Pin1+ Pin – Woofer 1 x Quest 12” High Powered Mid-bass Woofer Tweeter 1 x Quest 3” Voice Coil 1.4” Exit HF Transducer Horn Flare CD Horn Directivity (FOH mode) 90 x 60 Dimensions WxHxD mm 390X 340 x 600 Weight 23kg

Digital Feed Back Reducer cum Sound Processor, Frequency Response - 20 Hz to 20 kHz +/– 1dB Dynamic Range - 110 dB minimum, A-weighted, 20 Hz to 20 kHz Digital-to-Analog, Analog-to-Digital Conversion - 24 bit Impedance - Input: 10 k - Output 120 Input Clipping Level - +24 dBu minimum Output Clipping Level - +24 dBu - +12 dBu with 12 dB pad engaged - +6 dBu with 18 dB pad engaged Total Harmonic Distortion - < 0.05%, +4 dBu, 20 Hz to 20 kHz Propagation Delay - < 1.5 ms. Processing blocks add no latency Polarity - Input to output: non-inverting (inverting optional) Operating Voltage - 100-240 VAC, 50/60 Hz (auto-switching), 1 A, maximum Maximum Power Drain - 45 W

Dual Channel 15-Band Graphic EQ Number of Bands:2 x 15-band Q Type:Fixed Boost/Cut Range:±6dB, ±12dB Feedback Detection:Yes Low Cut Filter:Yes Analog Inputs:2 x XLR, 2 x 1/4" TRS Analog Outputs:2 x XLR, 2 x 1/4" TRS, 1 x XLR (sub out) Rack Spaces:1U

BRANDED Distribution amplifier 2 x 12

16 channel Analog Audio Mixer, with effect 16 mono channels 16 internal time-delay effects mic XLR, 1/4 inch jacks Channel insert Super wide gain mic line input 3 band EQ with MusiQ 2 pre-fade Aux sends, 1 post-fade Aux send 1 internal FX send, Illuminated mute, Sound image pan Illuminated PFL & peak warning indicator ALPS 100mm faders 4 stereo channels with 2-band EQ and inputs for extra sources. Stereo returns & playback All inputs with level control 12 bar meters Mono/stereo function on auxes 1&2 Monitor output section, Alt stereo output source Configurable USB stereo audio in/out

Hand Held Dynamic wired Microphones, Type Dynamic (moving coil) Frequency Response 70 to 15,000 Hz Polar Pattern Cardioid Output Impedance 600 Ω Sensitivity at 1 kHz, open circuit voltage -53.5 dBV/Pa¹ (2.10 mV) Polarity Positive pressure on diaphragm produces positive voltage on pin 2 with respect to pin 3 Weight 300 g (10.58 oz.) Switch On/Off Switch Connector Three-pin professional audio (XLR), male

Combo Wireless UHF Microphone system, SVX288IN/PG-58 • Available Frequencies: between 794 –806 MHz • Operating Range: LO power mode: 18 m (60 ft.)* HI power mode: 75 m (250 ft.)* * under typical conditions • Audio Frequency Response: 50 Hz – 15 kHz • Transmitter RF Output Power: LO power mode: 1 mW maximum HI power mode: 10 mW maximum • Audio Output Connector: XLR balanced and ¼" unbalanced • Maximum Output Level: -19 dBV (XLR), -5 dBV (1/4”) (R25 - Band for Thailand Regulation) (ref. +/-33kHz deviation with 1 kHz tone) • Battery Life: Up to 10 hours with 2 AA batteries • Dynamic Range: >90dB, A-weighted

Cables, Mic. Stands, Speaker brackets, speaker cables, Interconnecting, Cables, snake cable 16 pair, storing and operating rack, clamps and other allied items.

Visual System

Laser Projector, (Main Projector) WXGA Resolutions, 5,000 Lumens 3 LCD Laser Projector 1,500,000:1 contrast ratio 20,000 hours expected light source life (normal mode) HDMI 2 Inputs (1 shared with MHL) Perfect Fit 2 High Dynamic Range (HDCR2) 360° Installation 16 Watt Internal Speaker

LCD projector, (supporting side projectors) XGA 1024 x 768 Resolution 3,300 ANSI lumens white/color output 20,000:1 contrast ratio HDMI x 2 input 16 watt audio output 10,000 hours hybrid filter 6,000 hours lamp life (Standard mode) 12,500 hours lamp life (Eco mode) Embedded LAN/Wireless Compatible

12 to 16 ft Drop adjustable Heavy Duty Ceiling Mounting Bracket with Necessary cables for three projectors (Mains, HDMI).

Motorised Projection Screen, 16 ft x 11 ft, wall mounting, working on 230v AC, operation by Remote Controller unit and Manual Switch System, HI-GAIN Fabric.

2/3 ft Drop adjustable Heavy Duty Ceiling Mounting Bracket with Necessary Power cable.

Motorised Projection Screen, 6 ft x 4 ft, wall mounting, working on 230v AC, operation by Remote Controller unit and Manual Switch System, HI-GAIN Fabric.

HDMI Splitter/switcher, 2 x 6, Interconnecting cables etc to operate all the three projectors simultaneously

Installation & Commissioning Charges

STAGE LIGHTING, STAGE FURNISHINGS & FAÇADE LIGHTING SYSTEMS

STAGE LIGHTING SYSTEMS

SITC of 54x3W LED PAR Light used as Effect Light, Spot Light and Strobe Light etc. with below specifications: • Lamp: 54 X 3W RGBW LED (12R+18G+18B+6W) • Max. Power consumpsion: 160W • Power supply:240V AC, 50/60Hz • Power cable: 3 core 1.5 sq. mm. copper PVC insulated • Channels: 8 Channel DMX-512 • Beam angle: 25° • LUX @ 2m: 11,000 • Control mode: DMX,Manual and Master Slave • Dimming: 0 - 100% • Function: strobe, dimming, sound active and Master slave. • Housing: Diecast aluminium with black epoxy polyster powder coating • Power and DMX: Loop in and loop out • Certification: CE

SITC of LED PARCAN Light used for dance hall, architectural and stage lighting with below specifications: • Lamp power - 100W LED • Power supply - 240 AC, 50/60 Hz • Channels: 2 channel DMX 512 • Control: Manual, DMX • Color Temperature: 3000K • CRI > 90 • Function: Dimming, Strobe • Dimming: 0-100% • Beam Angle - 9/15/20° • Protection rating - IP20 • Certification: CE

SITC 200W LED Fresnel light used as a Key light, Back light, Fill light with dimming, spot & flood focus versions for creating various effects for multiple applications with specifications as below. • Lamp power - 200W COB LED • Power supply - 240 AC, 50/60 Hz • Power cable - 3 core 1 sq. mm. copper PVC insulated • Color Temperature: 3200K • Control : DMX512 / Manual • Spot - Flood focus adjustment: Manual • CRI > 90• Dimming - 0-100% through manual and DMX• Beam Angle - 10°-50°• Protection rating - IP20 • LUX at 2m: 38,200 at 10° & 3,500 at 50° (3200K) • Certification: CE

SITC of 200W LED Profile Spot Light used as a Spot Light and high-contrast gobo projection Light. Other Technical specifications as below: • Lamp Power : 200W COB LED • Power Supply : AC 230V, 50Hz.• CRI : >90 • Colour Temperature : 3200K• Focus : Manual Focus • Beam Angle : 19° • Control : DMX, Autorun and Master/Slave • Shutter arrangements : Beam shapping shutter or plastic gobo projection assembly. • Lux Level - 20,000 lux @ 2 Mtr with beam angle 19°,3200K • Dimming : 0 - 100% dimming • Protection Rating : IP20 • Body Color : Black • Certification: CE

SITC of LED 2x2 blinder matrix Light used in Entertainment applications, Night club, Fashion shows, Film, Band performances, Discotheque, Stage performance , TV studio and large-scale show etc fixture with advanced COB LED technology with below specifications:- • Power Consumption: 400W • Power Supply: 240 AC, 50-60Hz • Light Color: Single color warm white / Cool Light • Channel: 4/8 channel • Lifetime: Over 50,000 hours • Beam Angle: 30° • Control mode: DMX512,Master/Slave,Auto Run,Sound active. • Dimmer: 0 -100% linearly adjustable • LUX: 8200 LUX @ 2m • IP Grade: IP20 • Certification: CE

SITC of Diecast aluminum "C" clamp with safety locking chain, duly powder coated in black matt texture finish and technical specifications as below. • Finish - Pretreated and black epoxy polyester powder • Safe working load – 150Kg.

SITC of Safety bond with lock clip (Safe Working Load 100Kgs ) to be fixed around the grid to avoid fall of the material in case if the "C" clamp is not locked properly including all accessories etc complete as required.

SITC of Identification name plate round 80mm undergone through 7 Tank chemical treatement to keep them rust free and duly powder coated in matt White texture finish including all accessories etc complete as required.

SITC of MS suspender consisting of fish plate of 150X150X6mm undergone through 7 Tank chemical treatement to keep them rust free and with requisite anchor fastner duly powder coated in black matt texture finish & stud with 12mm threaded rod to keep the Bar rigidly held with Safe Working Load of 200kg including all accessories etc complete as required.

SITC of MS Pipe 40NB constructed in the form of 1m x 1m square matrix grid powder coated with Matt black finish, 2.2 mm wall thickness Pipe should have under gone 7 tanks chemical treatment process and rusto cleaned.

SITC of MS "C" track size of 40 x 50 x 40mm, 3mm thick with owal slot of 14 x 40mm at every 200mm undergone through 7 tank process with various chemical treatment to keep them rust free, duly powder coated with Matt black texture finish including all accessories etc complete as required.

SITC of Fixed Front of House light bar, length 10Mtrs made using 40NB dual barrel with perforated Cable tray undergone through 7 tank process with various chemical treatment to keep them rust free, duly powder coated with Matt black texture finish and provided with suitable suspender and clamps.

SITC of MS Power junction box made up of 22SWG CRCA sheet undergone through 7 tank process with various chemical treatment to keep them rust free, duly powder coated with Matt black texture finish 4 way 10A IEC Socket of below specifications:- • Rating : 10A, 240V AC • Operating Temp : –20˚C to +70˚C • Mouldings : Nylon, Flammability Rating UL94V-0

SITC of MS sheet metal fabricated power junction box duly powder coated and fitted with 2 10amps 3 pin IEC socket,ON/OFF switch and necessary glands to power splitters and console undergone through 7 tank process with various chemical treatment to keep them rust free duly powder coated with Matt black texture finish for dimmable points along with the cable glands.

SITC of MS Signal junction box made up of 22SWG CRCA sheet undergone through 7 tank process with various chemical treatment to keep them rust free, duly powder coated with Matt black texture finish 5 pin XLR DMX out connector of below specifications:- • All metal housing with RF protection & electromagnetic shielding • Connection to join pin 1 to chassis ground

SITC of MS Signal junction box made up of 22SWG CRCA sheet undergone through 7 tank process with various chemical treatment to keep them rust free, duly powder coated with Matt black texture finish finish 5 pin XLR DMX in connector of below specifications:- • Connection to join pin 1 to chassis ground.

SITC of DMX lighting junction loop box made up of 22SWG CRCA sheet undergone through 7 tank process with various chemical treatment to keep them rust free, duly powder coated with Matt black texture finish 5 pin XLR DMX in / out connector of below specifications:- • Connection to join pin 1 to chassis ground.

SITC of MS Auxilary fabricated marshalling boxes made up of 20SWG CRCA sheet undergone through 7 tank process with various chemical treatment to keep them rust free, duly powder coated with Matt black texture finish for all the light bar with required no of ivory connectors including all accessories etc complete as required.

SITC of MS Fabricated made up of 22SWG CRCA sheet undergone through 7 tank process with various chemical treatment to keep them rust free, duly powder coated with Matt black texture finish power junction box (PJB) to terminate the Motorized section power connections including all accessories etc complete as required.

SITC of MS perforated trays with tray lid of size 40 mm X 75 mm X 40 mm, treated with 7 tank process with various chemical treatment to keep them rust free, duly powder coated with matt black texture finish paint along with clamping arrangement including all accessories etc complete as required.

SITC of MS perforated trays with tray lid of size 40 mm X 150 mm X 40 mm, treated with 7 tank process with various chemical treatment to keep them rust free, duly powder coated with matt black texture finish paint along with clamping arrangement including all accessories etc complete as required.

SITC of Internal earthing copper bare conductor network for earthing of lightning bars ,cable trays & metal accesseries related to work coming under the scope of work including all accessories etc complete as required.

Supply, Installation, Testing and commissioning of Installation hardwares required for the successful execution of work

SITC of 12 Way Direct Lighting Distribution Board made up of MS CRCA sheet undergone through 7 tank process with various chemical treatment to keep them rust free, duly powder coated with Matt black texture finish consisting of suitable rating TPN incomer, SP MCB's for the junction boxes fixed on the top of the grid including wiring and busbar connection with proper earthing and Hinged door with magnetic door lock including all accessories etc complete as required

SITC of Digital Lighting Console with 512 DMX channels • 512 DMX Channels. • 1000 scenes memories. • 12 hot keys for scene recall. • 2 cross fade for scene change • save 512 group of chasers and each chaser contains 256 steps • Audio control. • DMX connection: XLR 5-pin • Weight: 2.3kg • Dimension: 482(W)x55(H)x176(D)mm

SITC of Wall mount 2 feeder motor control centre panel & Remote control panel ( for the motorized Light bar & motorized FOH bar & motorized curtain) with emergency trip, necessary contactors and relays, push button stations and contact elements to control the motors system for curtains including all accessories etc complete as required.

SITC of Grid mount photo isolator DMX Amplifier unit 1 DMX input and 8 isolated output with following specifications: • Power Supply: 90-240V AC, 45-63Hz. • Control: DMX 512 protocol, • Control Signal input: 5 pin XLR female,

Supply, Installation, Testing and commissioning of 5 Pin XLR Male & Female Connectors for DMX network

Supply, Installation, Testing and commissioning of 5 Pin XLR Termination Connectors for DMX network.

Supply, Installation, Testing and commissioning of Black valcro tape for Cable dressing.

Supply & laying of PVC Copper unarmoured flexible FRLS insulated multicore cable 1100V grade confirming to IS694 size 3cx1.5 sq mm including terminations etc complete as required.

Supply & laying of FRLS PVC copper multicore cable 1100V grade confirming to IS694 cable of size 7 core x 1.5 sq.mm including terminations etc complete as required.

Supply & laying of FRLS PVC copper multicore cable 1100V grade confirming to IS694 cable of size 4 core x 4 sq.mm including terminations etc complete as required.

SITC of Screened DMX signal cable for DMX network including terminations etc complete as required.

STAGE FURNISHING SYSTEMS

SITC of Main Valence fixing arrangement using 40NB Pipe 2mm thick, 10 mtr in length MS pipe, undergone through 7 tank process with various chemical treatment to keep them rust free duly powder coated with matt black texture finish with mounting brackets to suspend the arrangement including all accessories etc complete as required.

SITC of Main curtain track system 10 Mtr long, centre parting with overlap of 0.9mtr provided with, Heavy duty extruded aluminium I track of 48x84mm, powder coated Track mounting brackets constructed of C track of dimension 40X50X40mm Electromechanical drive unit with 3PH INDUCTION MOTOR, 1.1KW, 3000RPM, 90B5 FLANGE MOUNT with GI wire ropes of 3mm in diameter constructed with 7 bundles of 7 strands with steel core at center Curtain holding Nylon wheel trollies consisting of 4 wheeler master trolley and 2 wheeler trolley placed uniformly at specific interval of 200mm throughout the track.Nylon moulded 6201 Ball bearing Diverter pulley with with 90mm for outer diameter, 72mm diameter at groove base, 19mm pulley thickness & MS yellow passivated Routing pulleys with 165mm for outer diameter, 150mm diameter at groove base with 12mm pulley thickness including all accessories etc complete as required.

SITC of Fixed Rear curtain track system 10 Mtr long, centre parting with overlap of 0.9mtr provided with,Heavy duty extruded aluminium I track of 48x84mm, powder coated Track mounting brackets constructed of C track of dimension 40X50X40mm with Curtain holding Nylon wheel trollies consisting of 4 wheeler master trolley and 2 wheeler trolley placed uniformly at specific interval of 200mm throughout the track including all accessories etc complete as required.

SITC of Fixed Wing Structure designed as per site condition for a height approx 5 Mtr x 1.5 Mtr made up of MS Square tube of 25mm or higher size rested on pivotable trolley on a track for the rotation of the wing with all accessories as required.

SITC of Fire retardant velvette fabric 100% (2 times of the finished dimension) gathering for main Valance as per the approved patern and colour, not less than 300 GSM, duly stitched along with and eyelets including all accessories etc complete as required. Size :L 10 Mtr x H 1.2 Mtr.

SITC of Fire retardant velvette fabric with lining 100% (2 times of the finished dimension) gathering for main curtain as per the approved patern and colour, not less than 300 GSM, duly stitched along with eyelets including all accessories etc complete as required. Size: L 5.5 Mtr x H 5 Mtr.

SITC of Fire retardant cotton fabric 50% (1.5 times of the finished dimension) gathering for Rear curtain as per the approved patern and colour, not less than 250 GSM, duly stitched along with eyelets including all accessories etc complete as required. Size: L 5.5 Mtr x H 5 Mtr

SITC of Glazzed Cotton fabric fire retardant treated as per approved colour and make with a gathering of 0% stitched as per site condition, curtain provided with eyelets at every 200/250mm for uniform fixing. (For Wing) 5Mtr x 1.5Mtr complete with all accessories as required

SITC of MS Fabricated made up of 22SWG CRCA sheet undergone through 7 tank process with various chemical treatment to keep them rust free, duly powder coated with Matt black texture finish power junction box (PJB) to terminate the Motorized section power connections including all accessories etc complete as required.

Supply & laying of FRLS PVC copper multicore cable 1100V grade confirming to IS694 cable of size 7 core x 1.5 sq.mm including terminations etc complete as required.

Supply & laying of FRLS PVC copper multicore cable 1100V grade confirming to IS694 cable of size 4 core x 4 sq.mm including terminations etc complete as required.

FAÇADE LIGHTING

Dynamically color changeable RGBW LED round type light with DMX512 control for generating 16million colors. The body should be made of Die cast Aluminum with 7 tank processed to make it rust free and power coated for longer life. The LEDs should be CREE/OSRAM/LUMILEDS/NICHIA. The fixture should have beam angle options of 7°/10°/15°/30°/45°/60°. The Input to the LEDs to be 24V DC which should be supplied by a high quailty driver with power factor>0.9. The input voltage to the driver shall be 85-265V AC with 50Hz.The POwer consumption of the light fixture shall be 20-25W The fixture shall be weaatherproof with IP66 rating.

Dynamically color changeable RGBW LED round type light with DMX512 control for generating 16million colors. The body should be made of Die cast Aluminum with 7 tank processed to make it rust free and power coated for longer life. The LEDs should be CREE/OSRAM/LUMILEDS/NICHIA. The fixture should have beam angle options of 7°/10°/15°/30°/45°/60°. The Input to the LEDs to be 24V DC which should be supplied by a high quailty driver with power factor>0.9. The input voltage to the driver shall be 85-265V AC with 50Hz.The Power consumption of the light fixture shall be 32-37W The fixture shall be weaatherproof with IP66 rating.

Dynamically color changeable RGBW LED flexible linear light fixture with multiple LEDs mounted equidistantly for unifrom light output.The PCB shall be flexible and should be availiable for cutting at equal lengths. The LEDs shall be CREE/OSRAM/LUMILEDS/NICHIA. The input voltage to be light shall be 24V DC. The The power consumption of the light fixture shall be 13W/m to 15W/m.The fixture shall be weaatherproof with IP66 rating.

Power Supply unit with input voltage of AC 85-265V , 50- 60Hz. The Output Voltage shall be 24V DC. The Power Consumption of the POwer supply unit shall not be more than 200W. The unit shall be weatherproof with IP65 rating.

Digital to Analog converter for linear flexible light fixture. The operating voltage of the converter shall be 12-24V DC. The converter shall shall have DMX input and output ports for signalling. The Output shall be 4channels and voltage output of 12-24V. It shall have Dip switches for setting the DMX addresses. The body shall be Aluminum and shall be enclose weatherproof box which shall be IP65 rated.

Linear Aluminum channels for fixing the Flexible LED light fixture. The channels shoulbe surface mounted with clips to install on the wall or ceiling. The channels shall have a Milky White diffuser cover for emitting uniform light.

Dynamically color changeable RGBW LED linear type light with DMX512 control for generating 16million colors. The body should be made of Extrusion Aluminum with 7 tank processed to make it rust free and power coated for longer life. The LEDs should be CREE/OSRAM/LUMILEDS/NICHIA. The fixture should have beam angle options of 7°/10°/15°/30°/45°/60°. The Input to the LEDs to be 24V DC which should be supplied by a high quailty driver with power factor>0.9. The input voltage to the driver shall be 85-265V AC with 50Hz.The POwer consumption of the light fixture shall be 16-20W The fixture shall be weaatherproof with IP66 rating.

Grid mount photo isolator DMX,RDM Amplifier unit 2 input and 8 isolated output with following specifications: • Power Supply: 90-240V AC, 45-63Hz. • Control: DMX 512 protocol, RDM • Control Signal input: 5 pin XLR female, • Size: 482 x 44 x 145mm , • Weight: 2Kg.

Digital Lighting Console with 1024 DMX channels • 1024 Channels. • 96 Fixtures. • 96 Dimmer Control Channels. • Time control of scenes: Fade in/out, LTP slope • Channels for each fixture 40 primary + 40 fine tune • LCD display with back light • 600 Scene step • 60 Scenes/Playbacks • 10 Scenes to run simultaneoulsy • Master slider - Global, playback, fixture • USB Memory - FAT32 supported

Waterproof Power Connectors for Light Fixture

Waterproof DMX Connectors for Light Fixture

PVC Copper unarmoured flexible FRLS insulated multicore cable 1100V grade confirming to IS694 size 3cx1.5 sq mm.

Screened 5 core sheilded DMX signal cable for DMX network.

12 way Direct Lighting Distribution Board with TPN incomer of suitable rating and and outgoing SP MCBs of suitable rating

Other accessories like Junction Boxes, nuts bolts clamps, conduits etc required for complete installation of the system

Installation Testing and Commissioining of the system

SOLAR ENERGY

Solar Pv Module

On-Grid Solar Inverter: - 100800W Mono-Perc Solar PV module (400Wp each): 252 nos.

Solar Mounting Structure : - Galvanised Iron mounting structure

Maintenance Free Copper Chemical Earthing : - Maintenance free 3 m long, 17.2 mm Dia, chemical earthing, 250 micron, 25 kg chemical compound. Earthing Copper Cable

Lightening arrester : - Conventional Copper Lightening arrester,1000 mm long, 5 spike + 30 sq.mm down conductor copper cable + other accessories

Other Electrical Equipments : - DC Cable + AC Cable + MC4 Connector + Conduit pipe + Cable Tray, Walkway, Cable tie, Clamps, Wire Lugs, Insulation Tape etc

Installation and commissioning : - Designing, Erection, Testing and Commissioning & installation.

MISCELLANEOUS WORKS

Signage Works

Stainless steel letter with external ACP with LED lights 3D steel letter making with best quality 20 gauge (304grade) Steel sheet in English as per requirement (Arial black font) best quality LED light, letter size 24” per letter for total 14 letters per board and one comma 7” So for 2 boards total = 14 letters*2 boards *24” + comma 7”* 2 boards = 686”

Best quality external ACP board making (brand Alston Co.) with Aluminum panel size 28’x4’ as per requirement including two inch folding

Brass name plate making with engraved letters 20 guage), board size 15”x8”=120 sq” @20/sq= 2400/board with framing

Golden mirror name plate size 15”x8”

Installation charges minimum for both boards

Transportation charges minimum

Boom Barriers

Supply, Installation, Testing & Commissioning of Automatic Electric Boom Barrier with Micro Processor Based Control Panel with Drive Mechanism to prevent closing on vehicle, remote control, High speed, for Contineous Use on 230V 50Hz AC Single Phase Power Supply & Manual Use in case of Power Failure, Max. 10 Secs. Opening Time, 100% frequency for vehicular span up-to 6 mtrs maximum, Powder Coated, IP54, including 90 x 25mm rectangular/ 70mm Dia boom with anti scratch rubber beading of required length (As per Site Requirement), Fork Rest for Boom, Photo Cell, Flashing Light, complete as required.

Supply, Installation, Testing & Commissioning of Push Button for open & close of barriers.

External Development & Landscape

Granular Sub-Base with Coarse Graded Material ( Table:- 400- 2) (Construction of granular sub-base by providing coarse graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with vibratory roller to achieve the desired density, complete as per clause 401). for grading- I Material

Providing and laying 500x500x40 mm thick Turf paver (Turfpave XD) on 150 mm thick sub grade of compacted bed of 20 mm thick nominal size stone aggregate and base course and filling with 150 mm thick jamuna sand, including spreading, well ramming, consolidating and finishing smooth etc. all complete as per direction of Engineer-in-charge.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge).

Softscape Work

Preparing & leveling the surface for making Open Garden Area

Providing ,Digging & planting Mapple and Silver Oak Tree

Providing ,Digging & planting Ficus and Cypress green

Supply at site weed free grass seletion No.1 in carpet form

Water Fountain Works

Supply & fixing of 2 tier fountain FRP fountain suitabale for 12 feet dia waterbody. Size 12 feet dia and 12\14 feet height Body :FRP

Supply & fixing of Header line for Fountain Nozzle ensuring beautiful water feature formation. Body upvc\cpvc

Supply & fixing of (RGB)\Warm white LED lights complete in all respect. ABS Body with steel top (12v)

Supply & Fixing of Pump suitable for this fountain.

Supply & fixing Light Stand

supply & fixing of related fittings

Supply and fixing of panel for proper functioning of fountain includes contactors, & MCB, Relay, Push Button,

Supply & fixing of (RGB) controller for light

Plumbing work of fountain. This includes compete plumbing fitting in upvc pipe of fountain in all respect complete

Electrical work includes conducting cabling and fitting of lights & other electrical items in all respect

Testing & Commissioning & Transportation

Passenger Lift

Supply, Installation, Testing and Commissioning of passenger lift with power operated doors and AC variable voltage and variable frequency controls. Travel height G+4 and passenger capacity 8 persons, speed 1.0 m/secand and weight 544 Kg.

M/S PRASAD CONSTRUCTION & CO

R.S.AGRAWAL INFRATECH PVT. LTD.

M/s Raj Construction