Up-gradation of PHC to CHC Kunjpura Distt. Karnal (Pdg. Street light only).

Amount

Suply and erection of PVC copper insulated and sheathed 2-core circular flexible wire. Size 1.50 sqmm ( 48 / 0.20mm). 31.9

Supply and erection of moulded case circuit breakers on wall or on existing pedestal including bonding to earth and necessary connections. 15 amp.to 60 amp. 415 V ,10 KA 3-phase. 31.12 c (i)

Supply and erection of miniature circuit breaker / isolator 240 /415 V in the existing distribution board including making necessary connections. Miniature circuit breakers of 9 KA breaking capacity. SP MCB of 9 KA breaking capacity 6 amp. to 32 amp. 31.17a) (ii)

Supply and erection of pipe for wiring purposes including bends inspection boxes etc. where necessary and painting as required. Galvanised iron pipe 65 mm dia on flushed. 31.21 (xiv)

Earthing Earthing with GI earth pipe 4.5 m long and 40 mm dia with masonry enclosure on the top etc. as required . 31.22(i)

Extra for using salt and charcoal / coke for pipe earth electrode as required. 31.22(ii)

Pdg. and fixing 4.00 mm dia G.I.wire on surface or in recess for loop earthing as required . 31.22(xvi)

Supply and erection of under ground cable ,loose in existing pipe or trenches complete with necessary connections . 16 Sq. mm 4 Core Cable . 31.26 (xI) Ard.

35 Sq. mm 4 Core Cable . 31.26 (xIii) Ard.

Supply and erection of Godrej Almirah typeM.S.pedestal made of 50 mm x 50 mm x 6 mm angle iron frame with 3.00 mm thick M.S.sheet covering including shutters with suitable hinges and locking arrangement with Godrej type handle including round bars . The top covering should have downward overhang of 75 mm on all sides of pedestal , having two sets of water proof ventilation holes of suitable size on the sides , at top and bottom , each set containing four Nos. holes to discharge the heat produced by the current . The shutters fixed with rubber gasket of superior quality and of suitable size to make it water proof . The pedestal duly painted both inside and outside with two coats of approved paint and primary coat and its legs are embeded upto the entire depth in 1:2:4 cement concrete block , projected 75 mm all around the pedestal and and 200 mm above the ground level including the cost of all labour and material required to complete the job in all respect upto the entire satisfaction of the Engineer-in-charge of the work:- M.S.pedestal of size 600 mm wide , 750 mm high ,300 mm deep and bottom totally open , duly embeded in cement concrete block of size 750 mm x 450 mm x 200 mm above ground level duly plastered with 12 mm thick 1:4 cement plaster , having a base of size 900 mm x 600 mm x 250 mm below ground level. 31.33 (i)

S/E of mark double walled corrugated (DWC) HDPE pipe laid 1 meter below ground level including digging & refilling of Earth including cost of suitable size soicket /coupler for HDPE pipe including the cost of labour & material required to complete the job in all respect upto the entire satisfaction of Engineer in charge of the work. HDPE pipe 63 / 50mm outer dia / inner dia 31.67 (i)

Supply & erection of Hot Dip Galvanized octagonal pole of 3mm thickness, with base plate including cost of nut & bolts & all accessories as supplied by the manufacture incuding cost of foundation accessories etc. The foundation bolts as per manufacturer design should be hot dipped galvanised pole complete with door locking arrangement. Terminal plate consisting of 2Nos. 100A , 4pole neutral links including connection etc. with suitable connecting arrangement for 2No. MCB's /Kit kat including cost of R.C.C. 1:1:5:3 for foundation of size 0.7 M X0.7 M X1.8 M with minimum 8Nos. 12mm dia logitudinal MS reinforcement rods with ring of 8mm dia not more than 200mm C.C. for fixing the pole with all labour & material required to complete the job in all respect upto entire satisfaction of Engineer in charge of the work. 7 Mtr. Long pole with top dia 70mm and botom dia 130mm with base plate of size 220 x 220 x 12mm. 31.68 (i)

Supply and erection of metal clad bus bar chamber made from 1.6 mm thick M.S.sheet fixed with rag bolts on wall or on existing pedestal / angle iron frame including bonding to earth Copper bars 63 amp. 415volt 4 bars of 325mm each (Cross section 20x3mm) duly tinned over all size of the chember 375mmx295mmx140mm. 31.76

Supply / installation MS enclosure made of 16G MS sheet duly painted etc. for MCCB up to 100A. 4 pole including inter connection and fixing the same in existing MS pedestal complete with all labour and material required for the same up to the entire satisfaction of Engineer-in- Charge of the work. NS

Supply & Erection of Single arms bracket made of 50mm dia GI pipe B class ISI 1.50 mtr. Long with 25mm dia bottom pipe GI with coller pipe (GI) 125mm dia 60cm Long top covered with ornamental cap duly welded, painted 2 coats of aluminium paints on bracket and golden paint of ornamental cap including the cost of labour and petty material etc. complete in all respect upto the entire satisfaction of Engineer-incharge. Bracket duly erected on existing 9 Mtr. High Octagonal pole. NS

Supply and erection of LED Regular Streetlight Luminaires 90 W of Makes: Bajaj / Crompton / Polycab / Halonix / Surya warm white with Pressure die cast aluminium housing with lens and accessories required to complete the job in all respect including erection on existing pole for fixing including connection of the same upto the entire satisfaction of Engineer in Charge of the work. NS

Supply, erection and commissioning of Time Switch 32A. 3 pole / 230V time switch Indo Asian make automatic Timer ON/OFF the street light, pillars, wall, MS pedestal where ON/OFF point is available cabinet is fabricated from 22 gauge MS sheet painted, wiring, connection ON/OFF from the bottom of the cabinet the lite DB IP 54 protection complete with Digital timer, 32A. TPN MCB (Indo-Asian), fuse unit, indication lamp suitable for switch from rectifier system, switching system Bakelite connector 32A. Digital timer, auto / manual system, time setter, fiber sheet rubber & plastic components, wiring & component fitting, chemical (Epoxy) including the cost of labour and petty material etc. complete in all respect upto the entire satisfaction of Engineer-in-charge of the work. NS

malkhansinghelectricals

m/s shajal electric wroks

Som Nath Contractor