Construction of J.S.L.P.S Office at Smart City, Ranchi, Jharkhand

Amount

Providing & fixing of 10mm 4 Layer Polycarbonate Sheet I.Q Relax Makrolon Brand Sheet with Ug 2.5/SQMk, Opel White colour 50 Micron U.V. Coated & fixing with standard 60mm AluminiumProfileAlcox top & bottom section as per Drawing ( weight 1.1kg per RMT, minimum ) including EPDM Rubber Gasket for tiet sealing of aluminium section With end profile of aluminium and silicon sealant (Winsil 20 neutral grade ) as per drawing at site

Supply & Installation of 22mm thick multicell and multi-layered flux standing seam UV protected polycarbonate panel system along with standard fixing accessories as per direction of the engineer in charge. Panel shall be of min 22mm thickness in multicell truss bridge structure for more flexibility and better load bearing capacity. The entire panel shall be coextruded UV protected and block 99% UV rays. Panels shall have minimum six - seven layers. Panels with more layers will be preferred to control deflection due to snow load. Panels shall be a combination of translucent and opaque louvers integrated in clear body for angular day lighting and best diffused daylight in single long length to avoid any transverse joint in approved colours as per required lux level and design requirements. Panels shall be with all standard fixing accessories to ensure best performance for wind uplift, vibration, oil canning and visual appearance. Panels shall be manufactured with vertical standing seam and shall be fixed on Purlin (will be paid separately) with double tooth locking mechanism with SS HD Trapezoidal Fastener and big snap on connectors with a pull-out load of min. 7000N (7KN) tested as per ISO 6892:1998 and IS 1608: 2005. The Panels width shall be of 1000-1200mm (min) and panels with more width will be preferred to minimize panel junctions. Panels must satisfy Dart drop impact test as per IS 14443-97 shall show no sign of breakage on Polycarbonate sheets which have been exposed to UV for a min. of 500 Hours as per ASTM G 155. Panels shall not have Yellowness Index as per ASTM D 1925 of 15 units when tested on a sample exposed to UV for 500 Hours as per ASTM G 155. U value shall not be more than 1.7 W/m2K as per EN ISO 10077-2:2018. Flux panel shall be with additional End cap/Aluminium U/F profile/ Glazing Bar for ends as required. Trained and factory authorized labour with supervision to complete the entire panel installation as per drawing & direction of the engineering in charge. Colour: White louvers with clear body .

Providing and fixing standard fireman's axe with heavy insulated rubber handle conforming to IS: 926 complete.

Providing & Fixing of MS door made up of 16 gauge MS Sheet capable of accommodating fire hose reel, landing valve, hose pipes, fittings, 1 No. CO2 & 1 No. Dry podwer type portable fire extinguishers & accessories. The door shall have a front glass with lock and key arrangement & shall be painted with one coat of primer & two coat of finished stove enamelled post office red colour paint & "FIRE HOSE" written on front. (Approx. size of door: 2100 mm HEIGHT, WIDTH OF DOOR AS PER SHAFT SIZE )

Providing and Fixing of CO2 Portable 4.5 Kg Fire extinguisher, Carbon-Dioxide type Flat base Horn Including Valve, High Pressure Rubber Wire Braided Discharge Hose of not less than 10 mm dia. & complete in all respects including initial fill with CO2 Gas confirming to IS:15222. and IS 15683:2018 Marked. Location : Inside FHC, Parking Area, Electrical Room, Pump Room,

Supply & Fixing of 6 Kg ABC MAP-50% Powder based Fire Extinguisher, Applicable Fire Class A, B & C, EPDM Rubber Hose, NRV Valve and Helium Leak Detection Tested, Internal Coating - Epoxy Powder and External Pure Polyester Powder Coated (UV resistant), IS 15683:2018 Marked. Location : Open General Area, Inside FHC, Parking Area,

Supply & Fixing of 9 Kg ABC MAP-50% Powder based Fire Extinguisher, Applicable Fire Class A, B & C, EPDM Rubber Hose, NRV Valve and Helium Leak Detection Tested, Internal Coating - Epoxy Powder and External Pure Polyester Powder Coated (UV resistant), IS 15683:2018 Marked. Location : Open General Area, Inside FHC, Parking Area, Basement

Providing and Fixing of Portable 4kg Clean Agent HFC-236fa Fire Extinguisher, Gas UL Listed under EPA SNAP, EPDM Rubber Hose, NRV Valve and Helium Leak Detection Tested, Internal Coating - Epoxy Powder and External Pure Polyester Powder Coated (UV resistant), Suitable for Class A,B and C & Electrically Started Fires, Conforming to IS 15683:2018 Marked. Location : General Office Area, Inside of Critical Rooms i.e. Server Room, UPS Near Rooms, Fire Control Room etc.

Providing, fixing of 60 Ltr Mechanical Foam (AFFF-6%, Confirms to IS 4989 (Part-II), Trolley Mounted Fire Extinguishers, Fitted with 4 Metre EPDM Hose with SS Spring of 300mm & Air Aspirated Nozzle, CO2 Gas Cartridge of 300 Grams. Confirms to IS 4947, Brass Forged Cap, including all accessories complete in all respect. Applicable on Class A & B Fire, IS 16018:2012 Marked & CE Approved. Location : Near HSD Tank, DG Area

Providing and fixing Fire related signages printed on photoluminescent U1000 aluminium sheet of 1.0 mm (+-10%) containing Lumigen II as base chemical, covered under UV stablized coating and of appropriate size including fixing on wall, door, ceiling etc. with proper clamps, hangers, cleats, anchor fasteners etc.

Supply, fabrication, installation & testing of Aluminium sheet metal ducting duly polysulphide sealed complete with Splitter Damper, vanes etc. as required for OT and as per ISI specifications and as per approved shop drawings. Supply. Installation, testing and commissioning of insulation on the surface of the duct with duly laminated aluminum foil of mat finish closed cell nitrile rubber (Class 'O' ) with suitable adhesive, as per specifications and drawings. The Joints shall be sealed with 50mm wide and 3 mm thick self adhesive nitrile rubber tape Insulation. The rates shall include all materials of the insulation and labour works with adhesive, complete as required and specifications.Supply. Installation, testing and commissioning of insulation on the surface of the duct with duly laminated aluminum foil of mat finish closed cell nitrile rubber (Class 'O' ) with suitable adhesive, as per specifications and drawings. The Joints shall be sealed with 50mm wide and 3 mm thick self adhesive nitrile rubber tape Insulation. The rates shall include all materials of the insulation and labour works with adhesive, complete as required and specifications.The joint between the ducts shall be done by means of polymer “flange / slide-in channel” system to prevent air leakages. Turning vanes, elbows and reducers to be considered as part of supply of ducts. Ducts shall be supported by cable supports / GI slotted channels with threaded rods. Internal Stiffeners shall be used to prevent bulging of ducts for the sizes above 800 mm. 0.80 MM (22 Gauge ) With 32mm Insulation

1.00 MM (20 Gauge ) With 32mm Insulation

1.25 MM (18 Gauge) With 32mm Insulation

Supply and fixing of acoustic lining of supply air duct and plenum with thick Engineered Nitrile Rubber open cell foam having a Noise Reduction Coefficient of 0.55 with Density 140 - 180 Kg/m3 passing Class 1 Fire Performance test as per BS 476 Part 7, Air Erosion test for 10,000 fpm air velocity as per ASTM C 1071-05 and with built-in antimicrobial protection. The material should pass Fungi Resistance Test as per DIN EN ISO 846 Method A and Bacterial Resistance Test as per DIN EN ISO 846 Method C; to be applied using manufacturer's recommended Rubber based Adhesive in a blend of solvents. 20 mm

Supply. Installation, testing and commissioning of slot diffusers with/without damper as specified below and as per specification. 3-Slot Diffuser

2-Slot Diffuser

Supply. Installation, testing and commissioning of powder coated extruded aluminum Linear Grille. 100 mm

Providing and Fixing Underdeck Insulation with 50 mm thick with closed cell Nitrile Rubber with prelaminated Aluminum foil on one side having a low stable k value of 0.035 k.cal/hr.m at 10.C and minimum density of 40-55 ± 3 kg/cum.The R-value should be as per ECBC Code. 50mm

Supplying, installing, testing and commissioning of Air Cooled Invertor Split type wall mounted /Ceiling suspended 5 Star Air conditioners suitable for R410A or eco-friendly refrigerant with evaporating unit comprising of cooling coil, blower with motor in Metallic (Steel) casing and condensing unit comprising hermetically sealed scroll compressor, condenser coil, and propeller fan. Unit shall be complete with controls, interconnecting copper refrigerant piping with insulation, drain pipes and electrical cabling etc. between evaporative and condensing unit, refrigerant gas and oil and complete as per specifications. The unit shall be suitable for operating on 240 volt, 1 phase, 50 Hz AC supply with five star energy rating. The units shall be suitable for chorded remote operation. The refrigerant piping & cabling shall run in PVC sleeve Steel supporting structure for outdoor units suitable for wall mounting / floor mounting. Nothing extra shall be paid on any account i.e. refrigerant pipes, drain pipes etc. Providing, fixing and testing of copper refrigerant piping of appropriate sizes duly insulated with nitrile rubber insulation of 19 mm thickness and cabling for all types of split AC units. The pipes plus nitrile rubber insulation and cable are to be covered with PVC flexible conduits for protection.Note: Providing and fixing of Powder coated M.S. angle iron frame work for outdoor unit is also included in the above scope. Contractor to submit design/Scheme for Iron frame and obtain approval of engineer/employer before proceeding purchase & installation. Capacity : 1.5 TR (450 CFM)-Wall Mounted

Capacity : 2.0 TR (625 CFM)-Wall Mounted

Supply, installation, testing and commissioning of Scheduled Timer for wall mounted split type Air conditioning units.

Capacity 3000 CFM, SP 15 mm wg

Capacity 4000 CFM, SP 20 mm wg

Capacity 6000 CFM, SP 20 mm wg

Capacity 7000 CFM, SP 20 mm wg

Capacity 10,000 CFM, SP 25 mm wg

Capacity 14,000 CFM, SP 30 mm wg

INLINE FAN (Ceiling suspended) Supply, installation, testing, commissioning of Inline fan with vibration isolators & speed regulator, complete as per specification and drawing. The Motor shall be suitable to run on 1 phase/50 hz/ 220 v electrical power. 500 CFM with 12 mm static Pressure

600 CFM with 12 mm static Pressure

Supply. Installation, testing and commissioning of Fire rated sheet metal ducts shall be fabricated from Lock Forming Quality grade prime galvanized steel sheet with flanges complete with supports, vanes, dampers, links, levers and quadrants etc. as per specifications and drawings. Supporting distance shall not exceed 1.2 Mtr with 6mm thick fire retardant gasket suitable for 250 deg C 2 hr shall be used in duct joints along with fire sealants. Suitable access doors shall be provided at every 3m. The rates shall include all materials of the duct and labor for suspension and supporting arrangement for plenums, ducts, complete with fire retardant flexible connection as required and as per specifications.All fire rated duct, smoke exhaust ducts shall be quoted with flame bar BWII or equivalent to achieve the required fire rating, also all the related accessories gaskets shall be suitable for the required fire rating. . 1.25 MM (18 Gauge) Plenum & Exhaust Duct

Supply. Installation, testing and commissioning of exhaust air/fresh air louvers of powder coated extruded aluminum construction with bird screen, minimum 80 mm deep.

Supply and laying ,testing and commissioning of following sizes of Copper conductor control cables with PVC conduit & fixing clamps and effecting proper connections to equipment etc. of following sizes : 4C x 16 Sq. mm Copper Conductor (Armoured)

4C x 10 Sq. mm Copper Conductor (Armoured)

4C x 6 Sq. mm Copper Conductor (Armoured)

4C x 4 Sq. mm Copper Conductor (Armoured)

3C x 10 sq. mm Copper Conductor (Armoured)

3C x 16 sq. mm Copper Conductor (Armoured)

DATA, TELEPHONE SYSTEM INCLUDING ACTIVE COMPONENTS Supply, Installation, Testing & Commissioning of Patch Panel Cat 6 U/FTP 24 Port- Loaded as per technical specification. Supply, Installation, Testing & Commissioning of Patch Panel Cat 6 U/FTP 48 Port- Loaded as per technical specification. Supply, Installation, Testing & Commissioning of Patch Cord Cat 6 U/FTP 3 feet as per technical specification. Supply, Installation, Testing & Commissioning of Patch Cord Cat 6 U/FTP 7 feet as per technical specification Supply, Installation, Testing, Commissioning of Cat 6, 10G, U/FTP, Information Outlet including G.I. Box and modular cover plate as per technical specification. Supply , Installtion , Testing and comissioning of 15U wall mount rack with fans , 2 cable managers, satationary shelf , 2 Nos of hardware pkts as per technical specification. Supply, Installation, Testing & Commissioning of Network Rack 42 U with below included: Network Rack 800W x 2000H x 800D, Top cover with 4 x cutout, 2 x cutout for cable entry. Bottom cover with 4 x cutout for cable entry. All cutouts blanked with Plastic caps. 2 pairs, 42 U 19" Profile Type angle,Front & etc. complete as per technical specification. Supply, Installation, Testing & Commissioning of 24 port 10/100/1000Mbps, 4SFP module, L-2 Switch, POE as per technical specifications. Supply, Installation, Testing & Commissioning of 48 port 10/100/1000Mbps, 4 SFP Module, L-2 Switch, POE as per technical specifications. Supply, Installation, Testing & Commissioning of IP Based voice Communication System with 04 Port Voicemail ,04 Port FXS ,04 Port FXO ,1 PRI Trunk lines (30 Ch) Circuit with CLIP Facility , 200 IP users License ,01 Nos. IP Operator Console, 30 Party Conference ,Speed Dial, Music on Hold , Internal/ External ring difference ,Call Barring, Call Pickup, - Redundant server in active-Active mode as per technical Supply, Installation, Testing & Commissioning of Type 1 IP Phone . Graphic LCD display with backlight 3 user accounts with multi-line appearance keys Local and company-wide phone directories. Supply, Installation, Testing & Commissioning of Type Basic Phone account , Full duplex speaker phone, . Supply, Installation, Testing & Commissioning of Core Switch 24 1Gb/10GBASE-T ports, 2 10Gb/40Gb QSFP+ ports, 4 10Gb/25Gb/40Gb/50Gb/100Gb capable QSFP28 ports, 2 populated power supplies slots, with suitabe fan module slots, supporting RIP, OSPF, VRRP L3 protocols from day one as per technical specification. Supply, Installation, Testing & Commissioning of SFP+ 10GBASE-SR 10 Gigabit Ethernet Optics, 850 nm for up to 300 m,transmission on multimode fiber (MMF). Supply, Installation, Testing & Commissioning of 6 Core OM4 Multimode Fiber Cable as per technical specification. Supply, Installation, Testing & Commissioning of 24 Port LC multimode loaded LIU. Supply , Installtion , Testing and comissioning of 48 port loaded LIU for core switch to access switch connectivity over fiber. Supply, Installation, Testing & Commissioning of LC - LC Fiber patch cord OM4, 3 Mtrs. Supply, Installation, Testing & Commissioning of 6 Core, Single Mode, OS2 as complete as required. IP CCTV SYSTEM

Supplying, installation, testing & commissioning of 5MP 30 fps HD Indoor IP Dome camera with1/3-inch CMOS, Sensor pixels 1920 x 1080, Sensitivity-0.04 lx (color) , Dynamic range 75 dB Wide Dynamic Range (WDR), True day/night, Automatic Electronic Shutter, Video compression H.264 ; M-JPEG, White balance, BLC, H.264 quad-streaming, Motion/tamper/audio detection, Privacy Mask, Lens 3.6 mm lens, 3-axis adjustment (pan/tilt/ rotation), ONVIF Profile S, CE Certified. Supplying, installation, testing & commissioning of 5MP 30 fps HD indoor / outdoor IR IP bullet camera with 1/3‑inch CMOS, Sensor pixels 2612 (H) x 1980(V), Sensitivity-0.24 lx (color) 0.04 lx (mono) ,IR range 30 mtrs, Dynamic range 70 db, True day/night, Automatic Electronic Shutter, Video compression H.264 MP ; M-JPEG, White balance, BLC, Analog video output, Lens (zoom / focus) 3.6 mm lens, Two-way, full duplex Audio, Audio compression AAC, G.711, L16 , ONVIF Profile S, CE Certified. Supply installation and commission of pann tilt zoom camera with 360 deg pan and 90 deg tilt with 36 X Zoom having maximum resolution of Max. 1920 × 1080 @30fps,true day night camera with 130 m IR range , optional, fine picture at Ultra-low light,supports compression format H.265, H.265+, H.264+, H.264, 3D Digital Noise Reduction support. Supply Installation, Testing & Commissioning of IP network recorder with following feature Processor - Dual-core embedded processor . Two-way Talk - 1 channel Input, 1 channel Output, RCA,Video Output - 1 HDMI, 1 VGA , IP Camera Input - 8/16/32 Channel IP , Compression - H.264+/H.264/MJPEG,Video Resolution - 2560 × 1920, 2048 × 1536, 1920 x 1080, 1280 x 1024, 1280 x 720, 1024 x 768 , Hard Disk - 4 SATA Ports, up to 8TB ,Motion Detection - MD Zones: 396 (22 × 18),Recording Mode - Manual, Schedule (Regular, Continuous), MD (Video detection: Motion Detection, Camera Blank, Video Loss), Alarm, Stop, Backup Mode - USB Device /Network , Interface Ports - 1 HDMI, 1 VGA, 2 USB(1 USB 2.0 , 1 USB 3.0 ), 1 RS485, 1 RS232, 1 RJ45. Supply, Installation, Testing and commissioning of Managable 24 port Switch with Power on Ethernet (PoE) enabled, 10/100, RJ45 Access ports with PoE complete as required. Supply, installation, testing and commissioning of of 6 TB HDD all accessories complete as required. Supply installation and commissioning of 48 inch LED monitor for disply of camera.

SIGNAGE WORK Providing and fixing Laser Cut 5 mm Acrylic Signage with Plotter Cut Vinyl letters pasted above & Desired color vinyl pasted on Back. 4 Inch X 12 Inch Providing and fixing Laser Cut 5 mm Acrylic in desired color with Plotter Cut Vinyl Letter Double Side as required.4 Feet by 2 Feet Providing and fixing Backlit Acrylic Box Lit with Korean Led .2 Feet by 1 Feet Providing and fixing Laser Cut 5 mm Acrylic in desired color with Plotter Cut Vinyl Letter as required.2 Feet by 4 Feet Providing and fixing Backlit Acrylic Box Lit with Korean Led .2 Feet by 1 Feet Providing and fixing Laser Cut 5 mm Acrylic in desired color with Plotter Cut Vinyl Letter Double Side as required.2 Feet by 2 Feet Providing and fixing Frosted Film.8 Feet by 8 Feet Providing and fixing Laser Cut 5 mm Acrylic Letters with Pasted over 5 mm Acrylic Sheet with 6 studs.4 Feet by 3 Feet Providing and fixing Laser Cut 5 mm Acrylic Letters with Pasted over 5 mm Acrylic Sheet with 6 studs.2 Feet by 1 Feet Providing and fixing Laser Cut 5 mm Acrylic in desired color with Plotter Cut Vinyl Letter Double Side as required.4 Feet by 2 Feet

Overall size 2700WX1200DX750H , Table top made to the shape as per design and having overall size of 2700WX1200DX70m , under structure made of 18mm thick plywood with 0.6mm Mica pated , modesty panel made of 25mm thick , Table fixed with bottom edge beading as per requirement , Modesty Panel of Main table shall be finished with matching veneer 3±4mm of approved grains and colour with design as per engineer in charge , Side pedestal Main Table shall be sliding drawers made of 12 mm ply sides and bottom , 18 mm front and within 18mm BB boxing etc complete , Drawers provided for Main table shall be fixed with sliding channels handles locks etc complete , All visible surfaces of side to be finished with PU polish All internal and underneath surfaces of table shall also be finished with PU polish , All edge beading nails screws adhesives etc complete , all wooden surfaces shall be finished with PU polish.Overall size 1200WX600DX750H , top made to the shape as per design and having overall size of 1200WX600DX38mm , under structure made of 18mm plywood with 0.6mm mica pasting , fixed with bottom edge beading as per requirement , Panel shall be finished with matching veneer 3±4mm of approved grains and colour with design as per engineer in charge , Side shutter shall be opneable shutter made of 18mm ply sides and bottom , 18 mm front and within 18mm BB boxing etc complete , shall be fixed with sliding channels handles locks etc complete , All visible surfaces of side to be finished with PU polish , All internal and surfaces of Unit shall also be finished with PU polish , All edge beading nails screws adhesives etc complete, all wooden surfaces shall be finished with PU polish.overall size 2100WX450DX2100H , top made to the shape as per design and having overall size of 2100WX450DX2100mm , under structure made of 18mm thick plywood with 0.6mm mica pasting , fixed with bottom skirting bands 75mm ht with edge beading as per requirement , Panel shall be finished with matching veneer 3±4 mm of approved grains and colour with design as per engineer in charge , shutter shall be opneable shutter made of 18mm ply sides and bottom, Handles locks etc complete , All visible surfaces of side to be finished with PU polish , All internal and surfaces of Unit shall also be finished with PU polish , All edge beading nails screws adhesives etc complete ,all wooden surfaces shall be finished with PU polish.

2 / 3 Shutter + Open storage unit - Self PLPB 25 MM, Back PLPB 9 MM, Rest all PLPB 17 MM. 4 inch SS finish handle, 4 MM Glass and M.P. lock.The PLPB (Wood Base) of Grade II. The hardware used in this product are of HAFFLE, HETTICH, REHAU or its equivalent. All open edge sealed with 2 MM and .8 MM thick PVC Beading.

High Back Revolving Chair, Overall Dimension:- 720W ±10 x 720D ±10 x 1290H ±10 mm,Seat & Back of Chair is made of 12mm Hot Pressed plywood and connected with MS Powder coated L Patta of Size 65x8mm, Seat & Back cushioned with Pu foam in D-45 kg/m3 & Prime quality Leatherette upholstery , Seat Size:- Seat Size:- 540W ±10 x 520D ±10 x 60 Thick. ±5 mm , Back Size:- 530W ±10 x 730H ±10 x 60Thick. ±5mm,Mechanism: Torsion Bar Single point control, Provides maximum adjustability and scope for comfort, Seat & Back moves in same direction, Single/ Upright position locking, Tilt tension knob to loosen or tighten the tension according to users body weight,Gaslift:- Lift -Used gaslift of 100mm size of Class-IVgrade , Plastic Gas lift cover,Armrest:- Leatherette upholstered on foam Cushioned armrest fixed PP structure and SS frame, armrest fixed with seat & Back which gives comfort & Strength both to the chair,Chair Base & Wheels: Metal chrome plated Chair Base frame Made of 2.5mm thick, base Front edges are in nylon, base consists of 5 prongs with 650±5 mm pitch circle diameter, 60mm Dia. Black Nylon - Twin Wheel Pin castor .

Medium Back Revolving Chair, Overall Dimension:- 720W ±10 x 720D ±10 x 1160H ±10 mm,Seat & Back of Chair is made of 12mm Hot Pressed plywood and connected with MS Powder coated L Patta of Size 65x8mm, Seat & Back cushioned with Pu foam in D-45 kg/m3 & Prime quality Leatherette upholstery , Seat Size:- Seat Size:- 520W ±10 x 510D ±10 x 60 Thick. ±5 mm , Back Size:- 530W ±10 x H 610 ±10 x 60Thick. ±5mm,Mechanism: Torsion Bar Single point control, Provides maximum adjustability and scope for comfort, Seat & Back moves in same direction, Single/ Upright position locking, Tilt tension knob to loosen or tighten the tension according to users body weight,Gaslift:- Lift -Used gaslift of 100mm size of Class-IVgrade , Plastic Gas lift cover,Armrest:- Leatherette upholstered on foam Cushioned armrest fixed PP structure and chrome plated frame,armrest fixed with seat & Back which gives comfort & Strength both to the chair,Chair Base & Wheels: Metal chrome plated Chair Base frame Made of 2.5mm thick, base Front edges are in nylon, base consists of 5 prongs with 650±5 mm pitch circle diameter, 60mm Dia. Black Nylon - Twin Wheel Pin castor .

Two Seater Sofa having Overall Size1260W X 870D X 760H ±10mm ,Inner frame having in combination of solid wood wood and ply wood of 12 mm MR grade Upholstery Made Of upholstered with Synthetic leather with seasoned solid wood frame material of size 50mm x 50mm, Seat and back Attached with spring and belt , frame shall be padded with high resilience polyurethane foam having density 40kg/m3 in Seat and Arm and back 32kg/m3, Seat Height 400mm ±10mm, Hard wood facia 18mm thick MDF is to be provided on the arm facia, Under structure Leg made of PPCP, All oints of under structure Shall Be Properly Strongly and conformity with regulations . All the above items should be as per photo, sketch , specifications & direction of engineer-in- charge.

Table 900W x 60D x 750H mm, 25 mm thick PLPB Table Top 18mm Thick PLPB Board With 2mm Thick Pvc Edgebanded Finish With As Per Approved Laminate Shade. Top Supported Understructure Of Table Gable - End Made Of Prime Quality 18mm Thick PLPB Board. Top Size 900W X 600D , Modesty Panel Size 732H. All Wooden Panels Used 0.8mm Thick Pvc Beading. Table & Drawer Panels Flat Edge Duly Sealed With Pvc Beading . Pvc Bofurs Screw With Gable - end. All Wooden Panels Cleaning Corner Knitted Finish . All Wooden Panels , Gables & Modesty Fix Joints With Minifix Dowels & Other Fitting Equipment . All Wooden Panels Prime Quality Board With ISI Marked .The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for OFFICE FURNITURE range for ergonomic design.

Fixed Visitor Chair, Overall Dimension:- 600W ±10 x 680D ±10 x 920H ±10 mm,Seat of chair is made of 12mm thick hot pressed plywood pasted with PU foamD-32 kg/m3 with Leatherette upholstery, Back of chair is made of 12mm thick hot pressed plywood with fixed headrest pasted with Pu foamD-32 kg/m3 with Leatherette upholstery, Armrest:-wooden cladded armrest fixed with seat & Back which gives comfort & Strength both to the chair,Under structure: Cantilever frame made of MS chrome plated frame Round Pipe in (16 Guage) thick with PVC bushes.

SINGLE BED (Size: 1950x975x450/900mm) : Providing and Fixing Single Bed as per dwg. wooden frame made of Vertical legs 2 Nos of section 75x75mmx350 mm.long on outer edges of front side panel,Vertical legs 2 Nos of section 75x75mmx1050 mm.long on outer edges at Back side panel, Horizontal T.W. member of section 125x62.5 mm ties the outer edge Legs at 350mm. ht ( from floor) bed.18mm th comm. ply board (Green ply / Black berry / Century / Archid) 2 nos. pressed together (as per design) is fixed on front covering the front & legs upto the ht of 380mm ht. from floor lvl. and similarly 18mm th comm. ply board 2 nos. pressed together (as per design) is fixed at Back upto the ht. of 900 mm. from floor lvl. with Tilting back above 350mm. ht upto 900 ht. from floor lvl. 12mm. thick commercial Ply of approved Quality is to be provided and fixed on T.A. Bracing/Supporting Members of Section 35mmx62.5mm fixed at the spacing of 460mm c/c between Horizontal Frame members at the ht. of 360mm.finish ht. from floor. At Back above 350 mm. ht.upto 1050mm.ht from floor 40mm+20mm.Foam (50 Density) is provided duly covered with Upholstry (Cloth/Leatherite) of approved quality (approx. Rate Rs 800/- per R.Mt.) as per approval of Engineer incharge. (This item is excluding Cost of Mattress) Exposed surfaces of Ply Baord are Covered with 1mm tk Mica laminate (Make:- Aerolam / I lam / Royal Crown / Optus / Xylem) of approved quality,colour and make fixed as per Design with necessary 3mm. wide horizontal spacing at Front Exposed panel as per design.. All exposed edges of Play Board is to be covered with 6mm.th. T.Wood Beading as per approval.All exposed wooden surfaces to be polished with melamine polish of approved colour and shade etc complete. as per drawing and directions.Use Fevicol S.H. for all Joints. The work includes approved quality hardware ,lead,lift,labour etc complete as requiredand nothing will be paid extra for execution of the item.

SIDE TABLE OF BED IN MICA (Size: 550x400x450/650) - Providing & fixing Bed Side Table -Size:(Size: 600x400x450/650) as per design. Basic Structure/frame of Table is made out of 18mm thick commercial Ply board (Green ply / Black berry / Century / Archid) with 8 mm ply on back side to be fixed to the existing position on floor ao sides of Bed along the wall. Table will have 2-Nos.Drawers to be fitted with Telescopic Channels (Make Hettich/Ebco) made of 18mm.thk. comm. ply board on all sides and 8mm tk comm. ply on Drawer bottom, laminated from all inside faces,fixed with the help of SS Hinges and SS Handle as per approval/design. All external exposed surfaces of 18mm thick Comm. ply board is to be finished with 1mm thick laminated Mica as Apporved shade and colour. and all internal surfaces of Shelf,Cabinet and Back made of 18mm &12mm thick Comm. ply board is to be provided with1 mm thick liner mica laminate of approved quality (Make:- Aerolam / I lam / Royal Crown / Optus / Xylem), make and color. Provision for 12 mm thk clear bevelled glass on runner top shall be made. All Edges of Ply Board is to be protected by fixing 6mm thick T.Wood beading/2mm thick PVC Lipping/ 12mm.thick MDF Board. All exposed T.W. beading to be melamine polished/ enamel painted as per color scheme.Use favicol S.H. for all joints. The work includes good quality S.S. hinges/albihari hinges, S.S. handle, cluthers, locks, bolts and hardware of approved quality etc. wherever required.This work also includes Providing and fixing of 6mm thk corean finish sheet in Coloured/White colour of aprroved make /brand for Table Top,Front Top Edge (as per design & drawings), finished as per the directions and satisfaction of Engineer In charge, compelete.Work include all material, labour, installation at site etc. complete and nothing will be paid extra for execution of the item.

Conference Table Top 43 mm Thick (25mm Top + 18mm Batten) PLPB Board as Per Approved Laminate Shade. Understructure Top Supported 75X25mm Prime Quality Steel Frame Leg moulded With 18mm Thick PLPB Board. Modesty Panel 18mm Thick 450 mm High PLPB Board Supported To Top. Conference Table Top Size 4200W X 1500D In 18mm Thick PLPB Board. Provided Wire Management For Conference Table Top Flushed With Flapper. Wooden Panels Flat Edge Duly Sealed With 2mm Thick Pvc Beading. Conference Table Top Divided Into Two Parts. All Wooden Panels, Gables & Modesty Fix Joints With Minifix Dowels & Other Fitting Equipment. All Wooden Panels Cleaning Corner Knitted Finish. Legs Of The Table having Hard Rubber Shoes. Metal Flapper Size 400W X 120D Duly Powder Coated. All Wooden Top , Legs & modesty Panels Assembled & Dismental Any Places Easily. Metal Leg 75x25mm Shall be Neatly Jointed Together With 18mm Thick PLPB Board Accurrately Matching Sides Avoiding Any Gaps. The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for OFFICE FURNITURE range for ergonomic design.

Supplying Full High Back Chair Overall Size 1220H x 730D x 730W . Seat Plywood Made Of 12mm Hot Pressed . Upholstery PVC Structure Moulded With Prime Quality Leatherite . PHA ( Gas-Lift ) 85mm (TDC 152mm & BDC 67) . Seat & Back Are Firmly Connected To The Base Frame Machanism . Machanism Provided Upright Position Locking . Tilt Adjustment Can Be Operated In Seating Position . Chair Max Height 1220 . 500W x 450D Base Seat 80mm Thick Moulded With PU Foam ( H.D ) D - 45kg/m3 , H - 20 & 480W x 650H Back Seat 65mm Thick Moulded With PU Foam ( H.D ) D - 45kg/m3 , H - 21 . Moveblity Of Seat 80mm . 530/655 Arm Rest Adjustable Type PU + L BKT ( Chrome Plated Steel ) . Arm Rest Height From Seat 230 Minimum & 310 Maximum . 188L x 123W x 3mm Thick Spine Bkt. (Part - A) U Type Mild Steel Black Painted & 100L x 90W x 6mm Thick Spine Bkt. (Part - B) Flat Type Mild Steel Black Painted . Height From Seat To Ground 490mm . Understructure Used Base Chrome Plated Steel Frame . Casters Made Of Moulded Black Nylon Metal Bolt Inserted & Fitted With 5 Nos . Twin Wheel Casters 50mm Dia . Pedestral Pitch Centre Dia 670mm Without Casters & With Casters 730mm .

Supplying Medium Back Chair Overall Size 595D x 955H . Seat & Back Plywood Made Of 12mm Hot Pressed Supported . Understructure Base Of Chair Metal Structure Fixed Type . Upholstery Structure Moulded With Prime Quality Leatherite . Understructure Base Fixed Type CRCA 38x18x1.6mm Thick Metal Pipe Duly Powder Coated . Machanism & PHA ( Gas Lift ) NA . Seat & Back Are Firmly Connected To The Metal Frame . Chair Max Height 955 & min Depth 595mm . 510W x 420D Base Seat 70mm Thick Moulded With PU Foam , D - 45 kg/m3 H - 20 & 500W x 510H Back Seat 70mm Thick Moulded With PU Foam , D - 45 kg/m3 H - 21 . Back Seat Movability 80mm . Back , Seat Shell & L - Patta NA . 490/650 Arm Rest Fitted To The Seat With Armrest Connecting Brackets . Arm Rest Height From Seat 230Min & 300Max . Arm Rest Made Of Adjustable Pad ( P.U) + L Bkt ( Chrome Plated Steel ) . Spine Bkt Part A 188L x 125W x 3mm Thick Mild Steel Flat Type Side Capsule Tube Powder Coated . Spine Bkt Part B 100L x 90 x 6mm Thick Mild Steel Flat Type Side Capsule Tube Powder Coated . Height From Seat To Ground 470mm . Metal Pieces Shall Be Welded Properly Strongly and conformity with regulations . CO2 Welding Shall Be Used . All Metal Shall Be Coated After Being Treated With At Least Three Stages And Cleaned From Oil , Grease Dust And Other Dirt Using Special Thermal Control Coating For Metal Furniture To Form a Layer Of Base Coating Of (iron phosphating) (0.4 – 0.8) gm/m² . Automatic Spray Coating Shall Be Applied To Be Followed By a Drying Process In a Thermal Furnace With Suitable Temperature And Time For The Process . Thickness Of Coating (40 – 50) Micron.

Add 18 % G.S.T

Add 1% Labour Cess

Bidder Name

Amount

BABAN SINGH (GSTN-20BAJPS2420Q1ZK) BID ID -628421

M/s RAMAKANT SINGH (GSTN-NA) BID ID -627975

BABAN SINGH (BID ID -628421)

BABAN SINGH (BID ID -628421)