RFP for Interior Works for Establishment of PMU for IFMS 3 at LIC Building, Jaipur

Amount

Civil

Demolishing/dismantling manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material .All lead and lift from site up to 5km outside the site (dispose of the material) at safe place

Brick work/Stone Masonry/ CC/ Plastering/ Flooring/ Dadooing/ skirting/ tiles all types

Joinery( door, window, ventilator, vent, WC, urinals, wash basin,exisiting railing & MS shutter) and handing over to local authorities

Providing and fixing of W.C. pan (any type including WC cover,SS jali, health Facuets,cistern 10 liters etc all accessories), Urinals and wash hand basin including pillar cock,angle valve,connection pipe,outlet pipe,ss jali of all sizes with care including all necessary fittings P or S trap. Cost to include if any repair of pipe work or new pipe to be installed in all manners. Toilets to be handed over in working conditions

Providing and fixing Low level Flushing Cistern of 10 liters capacity (IS : 2556mark). Of approved make with complete fittings C.I. brackets duly painted, brass ball cock with ball, (IS: 1703 mark) complete including cutting and making good the wall: WVC with C.P. brass bend.

Providing and fixing C.P. brass Urinal Flush Pipe set complete with flanged brackets of approved make.

Providing and fixing Beveled edge Mirror/mirror with teak wood lipping around of special glass of approved make as per direction of Engineer-in-charge complete with 6mm thick commercial ply base fixed to wooden screws & washers.

Providing and fixing Louvers/frosted fixed glass with aluminum frame of 2"x2", including silicon sealant of approved brand on all edges. Frame should have a removable hardware to remove and refix louvers/glass. Size up to 3'x1.5'

Half brick masonry in Superstructure , above plinth level up to floor 3 level using bricks of designation 75 Cement mortar 1 : 6 (1 cement : 6 coarse sand)

Brick work with FPS bricks of class designation 75 in superstructure above plinth level up to floor 3 level in all shapes and size.. In Superstructure in cement mortar 1:6 (1 cement : 6 fine sand)

Repairs to plaster of thickness 12mm to 20mm in patches of area 2.5 sq. meters and under including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete including disposal of rubbish to the dumping ground within 5 km lead : With cement mortar 1 :4 ( 1 cement : 4 coarse sand)

Preparing the surface and plaster all internal RCC/ masonry surface with cement mortar 1:6, 20mm thick, smooth finished to line and plumb at all levels including all leads and lifts with necessary scaffolding, curing, hacking the surface, etc., complete.

Providing and fixing Partition Frame work made of 2" X 2" Aluminium spaced at 2'0" c/c vertically & horizontally. Additional member shall be provided at skirting, top band, grooves & at places where two different materials are combined. Necessary supports to the slab should be taken in to account. Partition panelling only with 18mm ply board The panels shall have grooves as per detail drawing finished with 1mm laminate as per design & detail. Shade and texture as per approved engineer in charge

Providing and fixing Glass Partition (on to above item or on masonry wall)using 10mm toughened glass with frosted film on frame all over aluminium frame. Design and detailing as per engineer in charge/ as attached in RFP.

Providing & fixing Single leaf Flush shutter door with door frame 150mm*75mm and - 32mm th. door finished with laminate on both sides and glazed panel in between. Shutter to have 35mm wide and 12mm thick lipping beading allround finished with enamel paint of approved brand, colour and shade., Cost to include necessary hardwares door closer, hinges, handle lock etc., complete. Size 3.5'x7'.Details to be followed as per engineer in charge.

Providing & fixing in position Single leaf framelass toughened glass door using 12mm toughened glass with edge polish. The door to consist of floor spring , Top patch, Bottom patch, Top pivot & S.S handle . Provide Patch lock .Cost to include silicon sealant. size is 3'x7'.Above lintel level fixed glass is to be fixed.The door shall be finished with privacy film.

Providing & fixing in position double leaf framelass toughened glass door which is frameless using 12mm toughened glass with edge polish. The door to consist of floor spring , Top patch, Bottom patch, Top pivot & S.S handle . Provide Patch lock .Cost to include silicon sealant. size is 3'x7' each leaf.The door shall be finished with privacy film.

Repair work of existing Aluminium windows & Vents (glass & frame) including hinges, handles, frame, joints etc. Making windows in working condition and lockable, glass cleaning or change if broken. (lumpsum)

Providing & fixing calcium silicate ceiling tiles of size 595 x 595 mm in true horizontal level suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 170 gsm/sqm.) consisting of main “T” runner with suitably spaced joints to get required length and of size 24x38mm made from 0.30mm thick (minimum) sheet spaced at 1200mm center to center and cross “T” of size 24x25mm made of 0.30mm thick (minimum) sheet, 1200mm long spaced between main “T” at 600mm center to center to form a grid of 1200x600 mm and secondary cross “T” of length 600mm and size 24x25mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600mm panel to form grids of 600x600mm and wall angle of size 21x21x0.30 mm and laying false ceiling tiles of approved texture in the grid including, wherever, required, cutting/ making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main “T” runners to be suspended from ceiling using GI slotted cleats fixed to ceiling with 6 mm dia and 50mm long dash fasteners, 4mm GI adjustable rods with galvanized level clips spaced at 1200mm center to center along main‘T’ bottom exposed with 24mm of all T sections shall be pre-painted with polyester baked paint, for all heights, as per specifications, drawing and as directed by engineer-in-charge.8 mm thick

Providing and fixing False Ceiling as per India Gypsum Specifications made of standard G.I. Sections and 12.5mm thick gyp board sheets inclusive of all hangers, edge members and other clips complete, with sheets fixed with proper screws by power drills and joints duly finished ensuring level in line and plumb to take final paint. All inclusive of detailed cut-outs for light fixtures, AC grilles. All Vertical drops will be measured extra as per actuals.The cost to be inclusive of surface preparation as per INDIA GUPSUM STANDARDS ( MODE OF MEASUREMENT L x B) .

Providing & laying flooring with skirting of up to 150mm of vitrified tile over a bed mortar of 20 mm thk in CM 1:5 or chemical laying as per the instruction of engineer in charge, including slurry, washing, cleaning etc tiles will be laid with 2 mm gap using spacers and gap will be filled with epoxy grouting of approved brand and shade, complete as per specifications. Necessary protective covering to prevent damage for the finish flooring to be given 300 microns plastic sheet and POP spread over it at no extra cost and to be retained until handover size:600*600. Mode of measurement LxB (floor area)

Providing & fixing 300mmx300mm & 6mm thick anti skid ceramic tile flooring of approved size and shade in 12mm thick CM 1:3, with cement slurry, pointing of tiles with Tile mate or equivalent to match the colour of the tiles, Proper slope to be maintained, curing ,oxalic acid wash etc., complete. no extra charge payable for cutting borders, cutting for drain holes etc.)

Providing and fixing Wall tiles of 300mmx450mm with vitrified tile on a backing plaster of CM 1:4 including slurry,12 mm thick including pointing with matching Cement grout , including acid washing, complete as per specifications and as per the sizes and pattern given by engineers. Rate to include cost of all materials and labour required for the finished job.

Providing and laying not less than 10mm thick FSC certified laminated wooden flooring of size 192mmx1200mm approx. The planks shall be provided with tongue & groove required for locking. The flooring to be layed with 3mm underlay foam and 60 microns LDF film placed over it as moisture barrier to proper level with necessary edge profile & reducer strip where ever necessary complete as per manufacturers instructions. The rate shall include 100mm skirting profile of matching shade, cost and conveyance of all materials,labor charges,lead,lift,laying Self leveling screed 3-5mm thk etc. All complete as specified and as directed by the Engineer-in-Charge

Providing and laying Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry, making of lines or groove etc complete but excluding the cost of nosing of steps etc. complete. 75mm thick with 20mm thick nominal size aggregate.

Providing and fixing Pantry counter made out of 18mm ply of size 10'(L)x2.5'(H)x2'(D), with under counter storage covered with openable shutter and 4 nos drawers of 6" height and 2' depth not exceeding 18" width. Top finished with Granite of not less than 16mm thick fixed with chemical adhesive mirror polished with diamond polish on edges chamfering of 5mmx5mm, silicon sealing of all edges. Cost to include 1mm laminate on outside and 0.8mm liner laminate inside all wooden counter along with edge band of matching shade, Also include necessary hardware like handle, hinges, telescopic channels with soft close mechanism. Skirting to be made out of PVC Skirting of approved shade and brand. Inside of carcase to have wooden shelves both side laminated.

Providing and fixing Granite stone slab mirror polished and machine edge cut in pantry Counters, Floors etc. laid on 20mm thick kota stone/wooden pantry top with means of approved chemical adhesive including base preparation on Kota stone/Wood and silicon sealing of edges. Granite of approved shade and specification not less than 16mm thick of base rate up to Rs. 200/sqft.

Providing and applying of acrylic emulsion paint finish to walls, blocked partitions, and plasterboard ceiling surfaces of approved shade, texture. Existing wall and ceiling surfaces to be prepared by scraping away any loose particles, dust, etc by washing and scrubbing and 1 coat of primer approved by manufacturer applied. The wall surfaces are then smoothened using putty approved by the manufacturers. Surfaces are then sandpapered to achieve a smooth finish and two or more coats of paint are applied as per manufacturer's specification.

Providing and applying Painting (two or more coats) on door and windows with synthetic enamel/Enamel paint of approved brand and manufacture and required colour over a priming coat of approved steel primer on new work. Colour to be taken approval from engineer-in-charge

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : a) first layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @0.253 kg//sqm .This layer will be allowed to air cure for 4 hours. b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm This layer will be allowed to air cure for 4 hours followed by water curing for 48 hours. The rates includes preparation of surface treatment & sealing of all joints ,corners, junction with polymer mixed slurry.

Making khurras 45*45 cm with minimum 5cm thick cement concrete 1:2:4 over PVC sheet,finised with 12 mm cement plaster1:3 and a floating coat of cement.

Grading roof for water proofing treatment with water proofing compound (quantity as mentioned by manufacturer) Cement mortar 1:3 (1 cement : 3 coarse sand) 50 mm thick including grid cutting of size approx 300x300 with thread cut method or suitable.

Drilling or Core cutting, horizontal, vertical or inclined holes in reinforced cement concrete and / or hard rock & filling the gape with suitable materials.

Diameters above 32 mm but up to 100 mm for a depth / length up to 300 mm

Diameters above 100 mm up to 200 mm for a depth / length up to 300 mm

Furniture

Supply & Installation WORKSTATIONS - 1200mm(W)x600mm(D)x750mm(H) Upbeat- Tabletop shall be of 18 mm thick Pre laminated on both side MDF board with molded Polyurethane edge on the working side. Understructure- The M.S pipes of size 20mmx40mm powder coated of approved shade legs should be connected to the understructure with the help of PDC Connectors to provide a stable and sturdy base for the worktops. The worktop shall be complete with provisions for screen mounting as well as for wire management on the workstation. Provisions for fixing of the switches shall be on the wire tray/channel. Access flaps with soft closing technology shall be provided on the table tops to access the switch points on the tray. Wire Management- It shall be a part of the understructure and can be in the form of enclosed metal tray to provide concealed wire management throughout the cluster formation. Wire riser leg shall be provided as per the layout structure Including following SITC of Free-Standing Pedestal Approximate minimum Dimensions – 420mm(W) X 450mm(D) X 550mm(H)Versatile 3-drawer office pedestal system solution shall be made up of 0.8mm ‐ 1mm CRCA sheets with powder coated finish. The drawers are meant to store stationary items like pens, calculators, staplers, files, folders, documents etc.It comes with sliding drawers and single lock operation along with caster wheels for 360‐degree movement. Including Supply & installation of one 16 AMP modular switch & 3 no. 6/16 AMP modular universal sockets with one no. CAT-6 LAN socket as per recommended makes with end plates & mounting boxes. as per 3D view matching with Photographs as attached in RFP

Low Height Partition: Providing and fixing low height partition of height 1200mm from finish floor. Partition to be fixed on floor with all necessary hardware. Structure made out of Aluminum frame of size 1"x2" approx with both side 12mm Ply wood fixed with screws finished with 1mm laminate of approved brand and shade having grooves and design as specified by engineer in charge. Top and side edges of partition to have Aluminum edge lipping of matching shade. Including soft board on both sides of height 2' cladded with linen based fabric of approved shade and texture. Soft board aligned with top of partition. Details can be found as per 3d views attached in RFP.

Supply & Installation of 3 Seater Sofa The seat should be made of PU foam with Density 32 ± 2 kg/cu.mtr having an additional top layer of J PU foam with Density 28 ± 2 kg/cu. Seat should be upholstered with fabric or leatherette. 2) BACK FOAM: The back should be made of PU foam with Density 28 ± 2 kg/cu. mtr with two additional top layer of super soft foam of density 23±2 kg/cu. mtr, upholstered with fabric or leatherette. Understructure: should be made up of 1.2±0.1 cm. thick hot pressed plywood . Dia 4mm zigzag spring assembly should be mounted in understructure for support and additional cushioning purpose .it should be a welded assembly made in Stainless steel (grade SS 202) tube & plate. as per 3D view matching with Photographs as attached in RFP

Supply & Installation of 2 Seater Sofa The seat should be made of PU foam with Density 32 ± 2 kg/cu.mtr having an additional top layer of J PU foam with Density 28 ± 2 kg/cu. Seat should be upholstered with fabric or leatherette. 2) BACK FOAM: The back should be made of PU foam with Density 28 ± 2 kg/cu. mtr with two additional top layer of super soft foam of density 23±2 kg/cu. mtr, upholstered with fabric or leatherette. Understructure: should be made up of 1.2±0.1 cm. thick hot pressed plywood . Dia 4mm zigzag spring assembly should be mounted in understructure for support and additional cushioning purpose .it should be a welded assembly made in Stainless steel (grade SS 202) tube & plate. as per 3D view matching with Photographs as attached in RFP

Supply & Installation of 1 Seater Sofa The seat should be made of PU foam with Density 32 ± 2 kg/cu.mtr having an additional top layer of J PU foam with Density 28 ± 2 kg/cu. Seat should be upholstered with fabric or leatherette. 2) BACK FOAM: The back should be made of PU foam with Density 28 ± 2 kg/cu. mtr with two additional top layer of super soft foam of density 23±2 kg/cu. mtr, upholstered with fabric or leatherette. Understructure: should be made up of 1.2±0.1 cm. thick hot pressed plywood 4. Dia 4mm zigzag spring assembly should be mounted in understructure for support and additional cushioning purpose .it should be a welded assembly made in Stainless steel (grade SS 202) tube & plate. as per 3D view matching with Photographs as attached in RFP

Supply & Installation of Center unit for Sofa Overall Size : Width : 118cm Depth : 60cm Height : 45cmTABLE METERIALS & SIZE :TOP:Sheesham 18 mm LEGS: 80X80 Top Side 40X40 Bottom Side Support 45x25mm & 8 Pcs Bolt & Nut Length : 1.1 mtr. as per sketch/drawing matching with Photographs as attached in RFP BOQ

Supply & Installation of Center Table for Discussion Room Centre table of size: 1200(Dia)x750(H) :TOP: Glass top with edge polish including all accessories. LEGS:SS legs with Chrome Finish. Rest detailing as per sketch/drawing matching with as per 3D view matching with Photographs as attached in RFP

SITC of Chair (Director's Chair) High Back with Cushioned Backrest, Synchronized Mechanism, Adjustable Armrest, Gaslift for Seat height adjustment, Standard 5-prong Nylon Base. Seat: PU, Backrest – PU, Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Chair (NIC/DOIT/DTA Officers and Reception) Medium Back, Mesh Back, Silver Epoxy Backbone, Synchronized Mechanism,Adjustable Armrest, Gaslift for Seat height adjustment, Standard 5-prong nylon Base, Seat - Fabric and mesh backrest, Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Chair (Visitor's chair) (Without Wheels) Low back visitor model ABS for seat, Mesh back with extra lumber Support with fine tuning for depth adjustment, with fixed armrest, silver epoxy cantilever base Upholstery: Black Fabric Seat & mesh backrest.Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Chair (Workstation Chair) Medium Back, Mesh Back, Silver Epoxy Backbone, Synchronized Mechanism,Adjustable Armrest, Gaslift for Seat height adjustment, Standard 5-prong nylon Base, Seat - Fabric and mesh backrest, Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Chair (Conference/VC Room Chair) Medium Back, Mesh Back, Silver Epoxy Backbone, Synchronized Mechanism,Adjustable Armrest, Gaslift for Seat height adjustment, Standard 5-prong nylon Base, Seat - Fabric and mesh backrest, Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

Supply & Installation of Reception Table 1850x750x1100 (LxBxH) Primary Work Surface Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Soft closing access flap with in-build power box are provided on work surface for wire management Secondary Work Surface Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. Modesty Panel Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. Under structure Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Drawer under counter in fronts made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. Drawer extension should be 325 MM. Drawers should have a soft closing & anti slam mechanism. Handles should be provided for ease of opening. Pedestals should be provided with lock for security. Including Supply & installation of one 16 AMP modular switch & 3 no. 6/16 AMP modular universal sockets with one no. CAT-6 LAN socket as per recommended makes with end plates & mounting boxes. including supply & provision of connector for Laptop connectivity. as per 3D view matching with Photographs as attached in RFP

Supply & Installation of Manager Table 1500x750x770 (LxBxH) Primary Work Surface Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Soft closing access flap with in-build power box are provided on work surface for wire management. Modesty Panel Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. Under structure Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Integrated Pedestal Made of 25mm. Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Drawer fronts made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Pedestal construction is BOX-BOX-FILE type which Uses powder coated 400 MM long metal Panel Drawer Slides. Drawer extension should be 325 MM. Drawers should have a soft closing & anti slam mechanism. Handles should be provided for ease of opening. Pedestals should be provided with lock for security. Including Supply & installation of one 16 AMP modular switch & 3 no. 6/16 AMP modular universal sockets with one no. CAT-6 LAN socket as per recommended makes with end plates & mounting boxes. including supply & provision of connector for Laptop connectivity. as per 3D view matching with Photographs as attached in RFP

Supply & Installation of Director Table 1800x750x770 (LxBxH) Primary Work Surface Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Soft closing access flap with in-build power box are provided on work surface for wire management. Modesty Panel Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. Under structure Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Integrated Pedestal Made of 25mm. Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Drawer fronts made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Pedestal construction of size 750(L)x450(D)x600(H) is BOX-BOX-FILE type which Uses powder coated 400 MM long metal Panel Drawer Slides. Drawer extension should be 325 MM. Drawers should have a soft closing & anti slam mechanism. Handles should be provided for ease of opening. Pedestals should be provided with lock for security. Including Supply & installation of one 16 AMP modular switch & 3 no. 6/16 AMP modular universal sockets with one no. CAT-6 LAN socket as per recommended makes with end plates & mounting boxes. including supply & provision of connector for Laptop connectivity. as per 3D view matching with Photographs as attached in RFP

Supply & installation of Manual Roller blinds having Aluminum Roller tube along with fabric pasted on it with glue having control unit for manual operations and bottom bar Aluminum powder coated for weight purpose, including fabric, fitting & accessories of approved make & colour etc. complete.

Supply and Installation of Meeting Table size 3000mmx1200mm table and 770mm height with laminate finish and leg to be box section MS powder coated. Top made out of 18mm ply with 1mm laminate finish of approved design and shade. Design and detailing to be engineer in charge. Including Supply & installation of one 16 AMP modular switch & 3 no. 6/16 AMP modular universal sockets with one no. CAT-6 LAN socket as per recommended makes with end plates & mounting boxes. including supply & provision of connector for Laptop connectivity. as per 3D view matching with Photographs as attached in RFP

Supply and Installation of U-Shaped Conference Table size 750mm depth having running length of 13.5 meters of table and 770mm height with Top made out of 18mm ply with 1mm laminate finish of approved design and shade and leg to be box section MS powder coated. Design and detailing to be engineer in charge. Including Supply & installation of one 16 AMP modular switch & 3 no. 6/16 AMP modular universal sockets with one no. CAT-6 LAN socket as per recommended makes with end plates & mounting boxes. Including supply & provision of connector for Laptop connectivity.As per 3D view matching with Photographs as attached in RFP

Supply and Installation of credenza: structure made up of 18 mm thick Prelaminated particle board with 2mm thick PVC edge banding tape.Approx. dimension 900(w)*450(D)*1200(H). Storage to be covered with openable shutter made out of prelaminated particle board with 2mm PVC edge band including all hardware: Hinges, handle, locks, etc. Shelves on inside to be provided with same materials as box.

Supply and Installation of credenza: structure made up of 18 mm thick Prelaminated particle board with 2mm thick PVC edge banding tape.Approx. dimension 900(w)*450(D)*1800(H). Storage to be covered with openable shutter made out of prelaminated particle board with 2mm PVC edge band including all hardware: Hinges, handle, locks, etc. Shelves on inside to be provided with same materials as box.

Providing and fixing of fabric based wallpaper of approved shade and brand not less than 220 GSM on specified areas wherever mentioned by means of suitable adhesive. Air gaps and wrinkles to be taken care of with proper alignment. Cost to include necessary scaffolding if required. Mode of measurement LengthxBreadth (application area).

Ceramic writing board with 25 X 40 Beachwood/ approved beading on 12mm ply - size 2400 x 1200

Providing and fixing Flex printing as per graphics approved hoardings outside the building as per size give by engineer in charge Approx. Dimensions:1200mm(W) X 900mm(H) with provision of backlight. Frame to made out of GI Sheet/M.S Frame, Lights to include LED fixture and wiring/circuiting with all necessary drivers. Cost to include supply, fixing, testing and commissioning.

Providing and fixing of Logo in reception made up of laser cut Anti-Corrosive high grade AISI 316 Stainless Steel size 1mtr by 1mtr .details given by engineer in charge. Cost to include graphical drafting on suitable software supported by CNC machine.

Providing and fixing Name plate for individual cabin and rest of the area. Signage's are made up of laser cut Anti-Corrosive high grade AISI 316 Stainless Steel of 2mm thick sheet with laser cut method for impression and with satin finish. Approx. Dimensions: 300 mm X 170 mm X 2 mm.Design and detailing provided by as per engineer in charge. Cost to include graphical drafting on suitable software supported by CNC machine.

Providing and fixing planter for indoor plants of size 2400x500x900(H) made out of moulded ceramic of approved finish and shade. Cost to include soil filling with appropriate and necessary fertilizer and chemical also include indoor plants (Snake plant, hybrid areca palm or equivalent

Description of Work / Item(s)

Amount

VRV System

Supply Installation, testing and commissioning of variable refrigerant Volume ( VRV) system, suitable to operate at Maximum temperature comprising of the following and complete as per specifications: Combination of hermatically sealed Scroll Inverter compressor suitable for operation on R-410A, complete with high/low pressure cut-outs, oil pressure failure switch, fan motor, safety thermostat, overcurrent relay, fusible plugs, fuses etc. and suitable for operation on 380-440V, 3 phase, 50 Hz A.C. supply.Matching air cooled condenser with copper tubes and aluminium fins duly covered by anti-corrosion and hydrophillic resin film.Oil separator suitable for the long refrigerant piping. Including Accumulator, liquid and gas shut-off valves and solenoid valves/modulation valve with fittings to interconnect compressor, condenser and evaporator coils. Quoted rates should include SITC of Additional Gas Charging of R-410

34 HP Capacity Heat Pump Type (Cooling & Heating )

SITC of Indoor units equipped with pre-filter, fan section with low noise fan, multispeed motor, coil section with DX coil, outer cabinet, drain pan, insulation, pipe connections, corded remote control etc. of various capacities as per specifications and drawings.

Ceiling Mounted Cassette Units:

1.0 TR HI-WALL WITH REFNET & WIRED REMOTE

2.01 TR 1-WAY CASSETTE WITH REFNET & WIRED REMOTE

2.01 TR ROUND FLOW CASSETTE WITH REFNET & WIRED REMOTE

3.98 TR ROUND FLOW CASSETTE WITH REFNET & WIRED REMOTE

TFA 2000 CFM/ 6.6 TR

SITC of Air Cooled split type Air conditioners complete with Indoor unit(IDU), Out door unit (ODU), surface / concealed copper Refrigerant piping with insulation (EP foam pipe section) upto 3 Mtr (IDU to ODU), copper power cable upto 4 Mtr (IDU to ODU), R-22/R-410 Refrigerant, Remote, suitable for 400/230V +10% of 50 Hz ,1 /3 phase AC supply capable of performing cooling, dehumidification, air circulation of following capacity with Scroll / reciprocating / rotary compressor as specified.

Hi Wall/Ceiling Wall Split

1.5 TR with 5 star rating of BEE

Communication Cable

Supply, installation, testing and commissioning of 2c x 1.0 sqmm control cum transmission wiring/power/control cabling with PVC insulated, PVC sheathed, multicore copper conductor control cable in suitable conduits between indoor and outdoor units and its remote controllers.

Supply, installation , testing and commissioning of Interconnecting refrigerant copper pipe work suitable for R-410A refrigerant with closed cell elastomeric nitrile rubber tubular insulation between each set of indoor & outdoor units as per specifications, all piping inside the room.All piping shall be properly supported with MS,GI HANGERS .All piping shall be pressure tested for 1.5 times the working pressure. . The refregerant pipes running in vertical shaft shall be supported on MS angle and wooden saddle at every 1200 mm distance and the pipes which are running horizontally above the false ceiling should be supported on MS angle/slotted angle at every 1200 mm distance.

Liquid Line including 13 mm closed cell nitrile rubber tubular insulation

Suction Line including 19 mm closed cell nitrile rubber tubular insulation.

Non-VRV piping

Drain Piping

Providing and fixing of UPVC drain water piping complete with fittings, support with MS hanger as per specification and insulated with 6/9 mm thick closed cell elastomeric nitrile rubber insulation.

Supply, installation , testing and commissioning Sheet metal ducting complete with supports, dampers, Vanes, nuts, bolts etc. as per specifications and drawings.

G.I. Sheet Metal Ducting (Rectangular)

0.63 MM (24 Gauge)

0.8 MM (22 Gauge)

Grilles/Diffusers/Louvers

Supply, installation , testing and commissioning of Extruded aluminium supply and return air grilles/diffusers/louvres, extruded aluminium dampers, supply air plenum etc. duly powder coated as per specifications and drawings.

Aluminium S/R air grill

Flexible Duct Connection

Supply, installation , testing and commissioning Fire retardant non porous double layer flexible connection between each fan and duct.

Duct Insulation

Supply, Installation, testing and commissioning of closed cell elastomeric insulation with microbial treatment of density not less than 50 kg/Cubm and material shall be in the form of sheets of uniform thickness.

9 mm thick

Duct Acoustic lining

Supply, Installation, testing and commissioning of open cell elastomeric insulation with microbial treatment of density not less than 50 kg/Cubm and material shall be in the form of sheets of uniform thickness. The ‘K’ value at 20o C. shall not be less than 0.037 W/mK.

9 mm thick

WIRING (supplying and fixing following items)

Wiring of light point/ fan point/ exhaust fan point/ call bell point as per specification for electrical Works with ISI marked 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV grade (IS:694) and 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade (IS:694) in recessed ISI marked MMS ( IS:9537 P - III ) vergin material PVC conduit & it's all accessories( J.B. , Bends etc.) , round tiles,18 SWG Hot Dipped Galvanized Modular Box with earth terminal, 6 A Modular switch, Modular face plate with grid plate, 3 pin ceiling rose / lamp Holder/ 3 pin connector , screws etc, making connections,all as per pre approved by Engineer in charge, testing etc. complete as required as per recommended makes of RFP.

Short point (up to 3 mtr.)

Medium point (up to 6 mtr.)

Long point (up to 10 mtr..)

Wiring of 3 pin 6 amp. Light plug point with 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV grade and 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade(IS:694) of approved make in surface / recessed ISI marked MMS ( IS:9537 P - III ) PVC conduit & it's accessories, 18 SWG 175 mm x 100 mm x 60 mm M.S. box with earth terminal, 6 A switch, 6 A socket, 3.0 mm thick ISI marked phenolic laminated sheet, zinc plated / brass screws, cup washers, making connections, testing etc. as required.

On board

Supplying and fixing of power plug point with Modular accessories as per specification for electrical Works, on hot dipped galvanized modular box of 18 SWG with earthing terminal/connector on surface or in recessed with suitable size of modular face place with grid plate and cover plate including cost of ISI marked modular 16 amp. Switch (IS :3854) and 3/5 pin 16 amp. socket outlet (IS:1293) , making connection , testing , etc. as required. All as per pre approved by Engineer in charge. as per recommended makes of RFP.

P & F 3 Way, 4 Conductors with current rating 16 Amp. Connector

S&F following sizes of ISI marked DLP U-PVC mini trunking systems along with accessories like end cap, internal angle, external angle ,Flat angle, Flat junction etc. on surface with screws, expansion fasteners as required. (make: legrand)

Mini-Trunking -32 x 12 mm

Finishing Accessories

End cap right or left

Changeable internal-external angle from 600 to 1200

Changeable flat angle from 850 to 950

Flat junction

White 32 x 10/12.5 cover joint

Supply, Installation, Testing and Commissioning of Flush mounted Pop-Up Box equipped with following items alongwith installation kits for table top. (i) 2 Nos. 6/16 Amp Socket (ii) Two LAN outlets (iii) 1 Nos. RJ-45 connector (iv) 1 Nos. HDMI outlets. Boxes should be in slim design for perfect integration into the furniture . (Make : Legrand)

S&F following sizes (dia.) of ISI marked MMS ( IS:9537 P - III ) vergin material PVC conduit as per specification for electrical Works along with its accessories (IS: 3419 ) as required in recess including cutting the wall, covering conduit and making good the same as required. All relative and latest acceptance tests reports by any NABL accredited lab for the conduit shall be submitted before execution & All as per pre approved by Engineer in charge .as per recommended makes of RFP.

Supplying and drawing FR PVC insulated & unsheathed flexible copper conductor as per specification for electrical Works with ISI marked (IS:694) and as per IS 8130 : 2013 of 1.1 kV grade . Wire should be made from 99.99% purity copper, class 5 stranding in acc. to IEC 60228 for lower watt loss , oxygen free ( <10 ppm) for less chances of oxidization and higher silver content for gives better conductivity , insulation PVC type A ,flame retardant as per IS 10810-53, better amperage rating as per VDE 0298 part 4, , in existing surface or recessed PVC/ MS conduit/casing capping including all as per pre approved by Engineer in charge,making connections, etc. as required. as per recommended makes of RFP.

3x 1.5 sq.mm

2 x 2.5 sq. mm. + 1x1.5sqmm

2 x 4.0 sq. mm. + 1 x 2.5 sq. mm.

2 x 6.0 sq. mm. + 1 x 2.5 sq. mm.

4 x 6.0 sq. mm. + 1 x 4.0 sq. mm. (DB supply)

4 x 10.0 sq. mm. + 1 x 6.0 sq. mm. (DB supply)

4 x 16.0 sq. mm. + 1 x 6.0 sq. mm.

DISTRIBUTION BOARDS

P&F recessed/ surface mounting heavy duty Vertical type 16 SWG sheet steel Distribution board with provision of incomer suitable for MCCB and SP / TP MCB as outgoing , phophatised ,powder painted complete with insulated suitable rating copper bus bar , neutral link, earth link and din bar, masking sheet & conforming to IS13032 & IS8623 including making internal DB terminations with copper lugs , testing etc. as required.

Double door (Three phase)

Double door (Three phase) Per phase isolation

P & F Recessed / Surface mounting heavy duty horizontal type 16 swg sheet steel cable end box phophatised / powder painted complete with cover plate, nut bolt, to be fixed at top / bottom of the DB to keep extra cable in the end box etc as required to cover the entire lenght of distribution board as mentioned in the above items.

Suitable for TPN DB

Providing & Fixing of 240/415 V AC MCB with positive isolation of breaking capacity not less than 10 KA (B/ C tripping characteristic as per type of load and site requirement) 4KV impulse withstand voltage, as per specification for electrical Works with ISI marked IS 8828(1996) / conforming to IEC 60898-1 2002, IEC 60947-2, low watt losses, trip free mechanisum , energy limiting of class 3 as per IEC, minimum phase termination capacity of 35sq.mm. , conductorline load reversibility, label holding facility , IP 20 contact protection and fitted with existing distribution board/sheets, min. operation 20,000 upto 32 A rating and 10,000 upto 63 A, 5000 for 80 A rating including making connections, testing etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work as per recommended makes of RFP.

Single pole MCB

6 A to 32 A rating

Double pole MCB

6 A to 32 A rating

Triple pole MCB

40 A- 63 A rating

Four pole MCB

40 A rating

63 A rating

Providing & Fixing of 240/415 V Residual current circuit breaker (RCCB) as per specification for electrical Works with ISI marked (IS:12640-1) / conforming to IEC 61008 -1 , rated conditional s/c current of 10 KA, truly current operated and shall operate on CBCT mechanisum, provision for pad lock, min. operation 10,000 upto 63 A rating and 5000 for 100 A rating, minimum phase termination capacity of 50 sq.mm. rigid wire , IP 20 contact protection with existing distribution board / sheet including making connections, testing etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work as per recommended makes of RFP.

Two pole 100/300mA sensitivity

40 A rating

Four pole 100/300 mA sensitivity

40 A rating

63 A rating

P&F recessed/ surface mounting heavy duty Vertical type 16 SWG sheet steel Distribution board with provision of incomer suitable for MCCB and SP / TP MCB as outgoing , phophatised ,powder painted complete with insulated suitable rating copper bus bar , neutral link, earth link and din bar, masking sheet & conforming to IS13032 & IS8623 including making internal DB terminations with copper lugs , testing etc. as required.

Double door including Incomer MCCB of 100 / 125 A Rating

Providing & Fixing of following modular accessories as per specification for electrical Works, made out of unbreakable and fire retardant vergin poly carbonate with brass terminals and captive screws & silver alloy contact tip with IP-20 rating , minimum width of 1 module switch toggle( PUSH PART ) should not less then 20mm, including all as per pre approved by Engineer in charge,making connections, testing etc. as required. All as per pre approved by Engineer in charge. as per recommended makes of RFP.

Blanking plate

Providing & Fixing of following size mounting grid plates with cover plates as per specification for electrical Works, made from fire retardent UV established high performance engineering plastic suitable for all universal metal boxes for front installation & removal direct fit type complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work as per recommended makes of RFP.

1/2 Module

3 Module

8 Module

Providing & Fixing of following size hot dip galvanized M.S. box of 18 SWG as per specification for electrical Works, with earthing terminal in recess/ surface suitable for modular accessories as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work as per recommended makes of RFP.

1-2 Module

3 Module

8 Module

Providing & Fixing of ISO certified company made vergin material PVC trunking system as per specification for electrical Works, with double lock feature for cable management including finishing accessories like corners, tee, adjustable angles, junction etc. as required . The trunking system shall have adaptable system for modular type RJ 45 data socket/ wiring accessories/ power sockets and shall be covered with peal off plastic cover. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work as per recommended makes of RFP.

80mm x 50mm

LED Lights and Fixtures

Providing & Fixing of IP40 LED Surface/ Recessed / suspended mounting Mid power SMD type LED Light fixture made from CRCA sheet steel housing, high purity / transmisivity UV stabilized Non -yellowish diffuser for uniform light distribution. High efficiency with 2.5 KV internal/external surge protection BIS certified isolated driver having efficiency > 85% , with Short & Open circuit protection and in compliance to IEC standards (Integral with light fixture). System lumen efficacy of ≥ 120 lm/Watt ,THD < 10 % , p.f.≥0.95,CRI >80 , life time of minimum 50000 Burning Hours with , 70% of intial Lumen maintaned till life ends , CCT 3000°K / 4000°K / 5700°K /6000°K/6500°K (As per ANSI Bin) , maximum power consumption should not more than the specified rating and Fixture shall be of BIS standard and trade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. All as per pre approved by engineer in charge .As per recommended makes of RFP

24 -32 W LED light fixture 2'x2' with acrylic / prismatic front cover.

Providing & Fixing of IP40 LED Recessed / Surface Mounted, Round / Sqaure Non-Dimmable Back lit SMD Mid Power LED Downlight with die-cast aluminum housing & Heat Sink for heat dissipation with UV Stabilized non yellowish Diffuser with internal/ external BIS complience 2.5 KV surge protected Isolated driver, with Short & Open circuit protection, having efficiency > 85% and in compliance to IEC standards. System Lumen efficacy of ≥ 120 lm / watt, THD < 10 % ,p.f.≥0.95, CRI >80, life time of minimum 50000 Burning Hours with , 70% of intial Lumen maintaned till life ends , CCT 3000°K / 4000°K / 5700°K /6000°K/6500°K (As per ANSI Bin) , maximum power consumption should not more than the specified rating and Fixture shall be of BIS standard and trade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. All as per pre approved by engineer in charge .As per recommended makes of RFP.

Recessed Mounting

LED Downlight 18/20W

EARTHINGS

SITC of chemical Gel earthing system of Dual Pipe Technology made of with "B" Class G I Pipe as per IS 1239 ( part-1):2004 of Medium duty of following sizes as per points mentioned (a), (b), [c), (d), (e) below :- (a) filled with anti corrosive conductive compounds with the permanent sealings at both the ends, CPRI/ ERDA tested with RMS capacity of minimum 35- 40 KA for withstanding 1 second . (b) To ensure the moisture content and electrical conductivity, 25 kg for 2000 mm & 50 Kgs for 3000mm of resistance lowering earth enhancement material shall be used as a backfill compound. The compound shall be tested form NABL acredeated lab for low resistivity ( less than 0.12 Ohm - meter) & high conductivity in nature with carbon as a major content as per referance of IS 3043-1987,IEEE 80-2013 (clause 14.5d) , IEEE 837 & IER 1956 with latest amendemnts (c)Heavy duty weather proof poly-propylene earth pit chamber with lockable Jam free lid suitable for safe working load 5000 Kg or more of size Top Dia. 225 to 260 mm, Bottom Dia 300 to 350 mm. and Height 250 to 300 mm. (d) Testing of earth resistance for value of 5 ohms or less as required & must record by engineer in charge during site visit and ensure to enter in measurment book. (e) All as per pre approved by Engineer in charge as per recommended makes of RFP

With Pipe in Pipe Technology (Outer pipe dia. / Inner pipe dia. ) Minimum 100 mm dia borewell

GI pipe 3000 mm long, 80 / 50 mm, Terminal 50 mm x 6 mm GI Strip

S & Laying following size earth wire/strip in horizontal or vertical run in ground/surface/recess on SMC insulator including riveting, soldering, saddles, making connection etc. as required.

8 SWG Cu wire

25mm x 3mm copper strip

32mm x 6mm GI strip

CABLING WORK

P/Laying P.V.C. insulated & P.V.C. sheathed armoured cable of 1.1 KV grade with aluminium conductor of IS:1554 P-I on cable tray, including cable termination, cable luges, cable gland, making connection, testing etc. as per specification, drawing & recommended make.

4 core 10 sqmm

4 core 16 sqmm

3.5 core 35 sqmm

3.5 core 50 sqmm

Fabricating & installing following sizes of perforated GI cable trays including horizontal and vertical bends, reducers tees,cross members and other accessories as required and duly suspended from the ceiling with M.S. suspenders and including painting

150mm x 50mm x 1.6mm

Providing & Fixing of heavy duty, copper wound , Double ball bearing and with metal sturdy mesh guard; Aluminium alloy one piece blade wall mounting oscillating type air circulator as per specification for electrical Works, conforming to IS:2997, including fixing with anchor bolts, regulator making connection testing etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work as per recommended makes of RFP.

450 mm sweep With wall Mounting and three speed regulator

Providing & Fixing of Heavy duty capacitor start, copper woind Double ball bearing 900/1400 RPM single phase Exhaust fan as per specification for electrical Works, conforming to IS:2312 ISI marked in existing opening including making connections testing etc. as required. All as per pre approved by Engineer in charge. .As per recommended makes of RFP

300 mm sweep(900/1400 RPM)

MEDIUM VOLTAGE PANELS

Main Floor Panel

Supply, installation, testing & commissioning of cubicle type totally enclosed free standing dust & vermin proof L T metering panel made out of 2.0 mm thick and partition made out of 1.6 mm MS sheet steel, suitable for 3 phase , 4 wire , 415 V , 50 Hz , AC supply complete with incoming MCCB & outgoing MCB/ MCCB, All the MCCB should be with Rotary handle, Dual source electronic energy meter, Electrolytic grade Al busbar of required capacity, indication lamp etc complete as per drawing & enclosed specifications recommended makes. INCOMER : 200 Amp, FP,25 KA, MCCB having Thermal Magnetic release with short circuit and adjustable overload (0.7 to 1In ) protection - 1 no 3P+N Type2 SPD with inbuilt health indicator, response time < 25 ns, Imax (8/20 µs) 8 KA, Voltage Protection Level 1.2 KV, shall be used at the incomer side of the panel with 32 Amp FP C curve MCB. - 1 no BUSBAR: 300 Amp, FP, Electrolytic grade Al busbar for main MCB outing & feeders distribution, The Bus Bar section should be covered with withdrawable Acrylic sheet for protection. OUTGOING : 100 Amp, TP, 25 KA, MCCB with neutral link, having Thermal Magnetic release with adjustable overload , & short circuit protection. ON/OFF TRIP, indication lamp - 2 nos 160 Amp, TP, 25 KA, MCCB with neutral link, having Thermal Magnetic release with adjustable overload , & short circuit protection. ON/OFF TRIP, indication lamp - 1 nos 40 Amp, FP, 10KA, MCB, - 1 no 63 Amp, FP, 10KA, MCB, - 6 no FOR SPARE 63 Amp, FP, 10KA, MCB, - 1 no 40 Amp, FP, 10KA, MCB, - 1 no METERING SECTION DIGITAL LED Energy meter (32 samples/cycle) of rating with 3 nos 250/5A class 1 as per IEC 62053-21, CTs as per SLD, The Digital meter shall measure V /I /F /PF /KW / KVA /KVAR / KWH / KVAH / KVARH / MD / %THD parameters. The energy meter should have communication modbus RS 485 port & required hardware & software for communication, duly protected by 2A MCB - 1 nos LED type RYB indication lamp duly protected by 2A MCB– 3 Nos.

80 kVAR APFC Panel

SITC of wall/ free standing floor mounted dust and vermin proof compartmentalised cubical panel as per specification for electrical Works, made out of CRCA sheet . Other parameters required as per point (a) ,(b), (c) below:- (a)Thickness of sheet shall not be less than 1.6 mm up to 600 mm length / width of any compartment and be of 2.0 mm above 600 mm. Load bearing structure shall be of 2.0 mm thick sheet supported by base M.S. channel if required . Side walls and cable alley compartments having bolted type doors with / without detachable extension type structure (b)panel shall be duly treated for derusting in 7 tank process with dephosphating and with powder coating of minimum 70 microns on both side of panel in desired shade The panel having PU/ Neoprene rubber gasket of not less than 3mm thickness ,required hardware, separate detachable gland plate M.S. base channel (min75mm) , hinged door with locking arrangement for equipment/switchgear [c) Interconnection between bus bar and switchgears /cable shall be rigidly supported and made out by flexible copper wires (up to 125 amp ) and by solid bus bar (>125 amp ) . All joints / interconnections of copper bus bar shall be dully tinned . Clearance between main bus bar and risers / metal parts shall be at least 10 mm additional to width of bus bar Bus bar is insulated by Heat Shrinkable sleeves . Earth and Neutral bus bar shall be half of the size of phase bus bar. All as per drawing pre approved by Engineer in charge. as per recommended makes of RFP .

Including supplying and fixing of Aluminium (IEC 60105 ISO 209-1,2) / Copper (IEC 60028) bus bar 6012 grade as per specification for electrical Works, by means of SMC / DMC type insulator, high tensile nuts and bolts spring washers in existing panel including bending , cutting in required shape and size and colour coding with heat shrinkable PVC sleeves. All as per pre approved by Engineer in charge and as per recommended makes of RFP .

Including Providing & Fixing of BIS approved 3 Nos. Current Transformer of rating C T Class 1, Ratio upto 200/5, Burden 5 VA as per specification for electrical Works ,ISI marked as per IS 2705-1992/ conforming to IEC 60044-1, with secondary terminal of CT shall be brought out suitable to a terminal block which shall be easier accessible for testing and terminal connection , with all necessary support in existing panel including connection etc. as required . All as per pre approved by Engineer in charge

Including Providing & Fixing of ISO certified company made UL listed , IP 65 110/220 V, unibody LED Indicating lamp(Red/yellow/Green colour) IEC 60947 , CSA 22.2 with integral circuit, IP 20 terminal block, Approx. body dia for panel not less then 20 mm, length min. 50mm, front LED cover dia min. 29 mm, contact material phospher bronze for Led, PCB contacts shall be of brass (tin plated), impulse dielectric tested for 2.5 KV, Rated insulation resistance shall be 100 M ohm at 500VDC including connection etc. as required. All as per pre approved by Engineer in charge and as per recommended makes of RFP

Including Providing & Fixing of IP 51 Multi function meter as per specification for electrical Works, ISI marked (IS 16444)/ Confirming to IEC 61557 & IEC 62052 with LCD/ LED 3/4 line display capable of measuring electrical parameters like V, I, F, PF, KW, Kva, Kvar, Kwh, Kvah, Kvarh display with 1A/5A CT input for LV/ HV network, with /without RS 485 communication port etc. All as per pre approved by Engineer in charge and as per recommended makes of RFP

SITC of IP 40 quick make and quick break 4 pole current limiting Moulded case circuit breaker (MCCB) of rating 160 Amp (Incomer) , 25 kA, adjustable O/L & fixed S/C setting, Ics = 100 % Icu made of flame retardent & heat resistant material having following current rating, short circuit breaking capacity at 440/415 V, 50 Hz; O/L & S/C settings as per specification for electrical Works, conforming to IS/IEC 60947 P -2 :2003 with front face and centralised adjustable, trip free mechanisum, true contact position indicator, line load interchangeability, designed for both horizontal & vertical mounting without any adverse effect on electrical performance, suitable for operation upto 55 degree and without derating upto 40 degree, pollution degree 3, having positive isolation capability, push (test) to trip, trip time less then 10 ms under s/c condition, Breaking capacity Ics = 100% Icu. U imp =8 KV, rated insulation voltage 800 V, provision for UVR , shunt trip , earth fault trip, door interlock, pad lock & rotary handle , including making connections with lugs & spreaders, etc. as required. as per recommended makes of RFP .

Capacitor Bank – 80KVAr (1-2-2-5-10-10-10-20-20) Capacitor steps: (a) First steps - 1 KVAr (b) Next two - 2 KVAr (c) Next one - 5 KVAr (d) Next three - 10 KVAr (e) Next two - 20 KVAr

SWITCHING 3 P, 440 V capacitor switching contactor duty AC - 6b of required rating with suitable rating MCB as per SLD (a) 1 KVAr with 6 Amp D curve TP MCB (b) 2 KVAr with 10 Amp D curve TP MCB (c) 5 KVAr with 16 Amp D curve TP MCB (d) 10 KVAr with 32 Amp D curve TP MCB (e) 20 KVAr with 63Amp D TP MCB 16 KA

14 stage Microprocessor based APFC relay of sensitivity less than 50 ma - 1Nos

LED type ON indication lamp –18 Nos

The CT sensing of the APFC relay shall be from the incomer side of contacotr (JVVNL supply). All control wiring from Bus bar to MCB, capacitor duty Contactor & Capacitor bank will be of required Ratings PVC insulated flexible copper wire.

80 kVAR APFC Panel

Supply, Installation, testing and commissioning of 40 KVA UPS with 3 phase input and 3 phase output and as per the Technical specifications. Quoted rate shall be inclusive of required batteries of 15 minutes back up at full load, battery shall be with connecting cables, Battery rack and all complete as per drawings, technical specifications, SLD, relevant standards, and direction of Engineer in charge.

Technology and Capability: a) True Online configuration with double conversion UPS b) DSP based technology with reduction in electronic components. c) Fully rated power (kVA=kW) for maximum power availability. d) Possibility of enhancing UPS capacity / redundancy by operating UPS in N+X Parallel Redundant Configuration(PRS). e) Capability of Independent or Common battery bank operation of the UPS when operated in PRS. f) UPS should be designed at Rated PF of 1. g) Dual Input design. h) UPS shold have IGBT topology for both PFC (power factor correction) and inverter. i) Inbuilt casters for easy movement & maintance. j) Energy recycle mode. k) Hot standby Redundancy function.

Input Voltage Range : 220/380V，230/400V，240/415V (3Φ4W) Range (Full Load) 305~478 VAC Range (Derating to 70% Load) 228~478 VAC Nominal Input Frequency : 50 Hz Input Frequency Range : 40 to 70 Hz Input Power Factor : > 0.99 (Full Load)

Nominal Output voltage : 220/380V,230/400V,240/415V (3Φ4W) Output Voltage Regulation : ± 1 % Nominal Output Frequency : 50 Hz Output Frequency Regulation : ± 0.05Hz Output Frequency Slew Rate : ＜1Hz/sec Output Wave Form : Pure sine wave Output Voltage Distortion (THDu) : < 1.5 % (linear load) Crest Factor : 3 :1

Transient Response (For load regulation from 0% to 100%steplinear load) : <±5% Transient Response Recovery time : Recovery to 3% is less than 20 ms Transfer Time (Mode of operation) : Zero ms from Mains mode to Battery Mode Zero ms from Battery Mode to Mains mode Transfer Time (UPS to Bypass / Bypass to UPS) : <1ms Overall Efficiency (AC to AC) - Online (Double Conversion) : >96% Overall Efficiency (AC to AC) - ECO Mode (Bypass feeding the load under normal conditions) : Upto 99% Inverter Overload capacity : ≤105 %: continuous,106% ~ ≤110%: 60 minutes; 111% ~ ≤125%: 10 minute; 126% ~≤150%: 1 min; > 150%: 1 second. Fault Indications (On Color touch screen display) : Main Input Sequence Fault,Power Module General Fault,Battery Ground Fault,Bypass Static Switch Fault,Parallel Fault,System General Fault,Provide Bypass O/P Even If UPS Fault.

Backup Required : 15 Min backup Battery Bank VAh (Vendor to include battery sizing calculations with tender) : Min VAH 24000 or higher Batteries Type : Sealed Maintenance Free (SMF) - 12V Cells Battery Makes : Amara Raja / Exide / HBL / Amco / Rocket/Quanta Inbuilt charger : Minimum 13A Operating Temperature : 0℃ ~ 40℃ Storage Temperature : －25℃ ~ 70℃ Noise Level : ＜ 56dB at 1 Meter

40 KVA 3 Phase Input, 3 Phase Output

LAN Services:

DATA & TELEPHON WORK

Supply , Installation, Testing and Comissioning of Wall mounted Communication rack with glass doors, handles ,lock , Top and Bottom Cable entries, Supports for mounting rack on wall , Cable managers, one Fan, Equipment mounting hardware, power supply box for supplying power to switches, fans etc along with earth continuity kit, Mcb, indicator, moulded power supply cable

12 U(44 mm ) wall mounted

Supply, Installation, & Testing of 19" 1U Rack Mounted/ surface mounted aluminum/ CRCA 1.2mm powder coated, multimode glass Fiber Optic Cable Patch panel/LIU loaded with flangless/screwable adapters for ST/E-2000/SC/LC/MT-RJ/PC type, It should have easy removable Top plate with push buttons, there should be a splice tray installed in the Patch panel/LIU which can handle the fiber cores, splice tray should be PC+ABS material, it should include accessories like mounting hardware, gormetts, heat shrink tubes/sleevs, screws, nuts to install the panel for rack/wallmount applications as per requirement complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work as per recommended makes of RFP.

Multi Mode LIU 6 Ports

Multi Mode LIU 12 Ports

Supply, Installation, & Testing of Indoor duplex Multimode patch cord (50/125 µm made of glass fiber optic with LSZH jacket, Multimode G652.D Mounted on both sides with ST/E-2000/SC/LC/MT-RJ/PC type Duplex connectors in acc. with IEC 61754-20 as per latest ammendments of TIA/EIA 569B.3, as per requirements complete in all respect. All as per pre approved by Engineer in charge as per recommended makes of RFP.

Supply, Installation, OTDR Testing & Fusion Splicing of Fiber Multimode Pigtail (50/125 µm) made of glass fiber optic, should be fitted at one end with any one type of single ST/E-2000/SC/LC/MT-RJ/PC type connector in acc. with IEC 61754-20, as per latest ammendments of TIA/EIA 569 Standard Specification as per requirments complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work as per recommended makes of RFP.

Supply, Drawing and Testing, of stranded Multi mode (50/125 µm) glass optic fiber cable, as per latest ammendments of TIA/EIA 568/ISO/IEC 11801:2011/ IEC 60794-1-2 E1, E3,E11, F1/ EN 50173-1/ EN 187 000/ IEC 60974-2, 2-20, 2-21/ ITU G.652D, construction of LSZH outer sheath cable, cable should be used for LAN and WAN back bones, . With its LSZH sheathing these cables should be ideal for indoor/outdoor installations in existing MS/PVC /HDPE Conduits/ slotted channels with ferruling at both ends for identification complete in all respect. All as per pre approved by Engineer in charge. as per recommended makes of RFP. (10 -G Cable)

6 core 10G glass optic fiber Cable)

SITC of FM Connector (specifically designed for tool less connection for CAT6 FTP / Outdoor cabling system, can be usable for multiple times) required for both end connectivity to take care for Data connectivity as well as Power for the cameras, The FM connector shall be used for earth connectivity at both end

Supply , Installation and Testing of 4 pair, 100 Ohm impedance, Cat 6/6A patch cords should be constructed of minimum 23/24 AWG, stranded bare Copper cable with FRPVC/LSZH Jacket, with an enhanced performance by factory moulded RJ45 connectors as per ANSI/TIA/EIA 568 suitable for Cat 6/6A application complying to latest ammendments Category 6/6A Standards, According. to TIA568, minimum requirement for 1G BASE-T/ 10G BASE-T performance. Patch cords shall be straight thru cable compatible with both T568-A and T568-B wiring schemes, Minimum 750 to 1000 mating cycles in plug contacts for long durability complete in all respect. All as per pre approved by Engineer in charge. as per recommended makes of RFP.

Cat 6, UTP (Un-sheilded Twisted Pair) Patch Cord

Supply, Installation, Testing and Comissioning of Rack mounted 19" 1U, 24 Port Unloaded, 1.5-1.6 MM CRS chasis, powder coated, sheet steel, made of plastic (ABS), Modular Patch Panels (without I.O.) with Rear Cable management system and mounting hardware to mount the patch panel. Should have port identification numbers printed/engraved on front of the panel, . There should be a provision for each port/jack on the panel and reusable removable on field from the panel complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work as per recommended makes of RFP.

SITC of Intelligent Ethernet POE Switches providing 24x 10/100/1000 Fast Ethernet POE ports- 370W or better and 4 dual purpose uplink (provision for Copper / Fiber Giga connectivity) with provision of minimum Stacking of 06 Switches with related LAN Base Software . For additional technical parameters of products/ work as per recommended makes of RFP.

Supply, Installation, Testing and Comissioning of Rack mounted , 48 x 10/100/1000 Ethernet ports Gigabit Switch with 4 mini Gigabit Interface Converter slots(shared with 4 Ethernet ports) for Gigabit Ethernet expansion , Switching capacity 96 Gbps nonblocking , . As per recommended makes of RFP.

Supply, Installation, Testing and Comissioning of 1G SFP (small form-factor pluggable) transceivers as per recommended makes of RFP.

Supply, Installation, Testing and Comissioning of 10G SFP (small form-factor pluggable) transceivers as per recommended makes of RFP.

Supply, Drawing and Testing of 4 pair, 23 AWG Solid Bare Copper wire insulated with PVC, UTP (Unshielded Twisted Pair), Category 6, Class E, 100 Ohm Impedance, Indoor Cable as per latest ammendments of ANSI/TIA/EIA-568 , The copper conductors should be balanced twisted in pairs, seperated by a cross-member fluted pair divider & protected by PVC Jacket. Certified performance in a 4-connector configuration upto 100 Mtrs channel requirements & transmission frequencies up to 250 Mhz. in existing MS/PVC Conduits/casing capping including making connections to Information outlets and Patch Panels with jack & ferruling at both ends for identification with necessary tools for punching, stripping, crimping and testing etc as required complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work as per recommended makes of RFP.

Supply and Installation of unsheilded/ sheilded Information outlets made of high impact plastic body with ABS, FR Grade with provision for protection against dust in jack/ FP, suitable for Cat 6/6A application complying to latest ammendments, According. to Cat. 6/6A channel, It should support channel as well as components requirements of Cat.6/6A standards at frequencies of up to 250 to 500 Mhz. Cat 6/6A unshielded/shielded Jack should be suitable to terminate 4 pair, 23/24 AWG solid/stranded wire diameters, using 100 Ohm unshielded/shielded balance twisted pair cable, the jack should have tooless/impact punch termination on reliable copper tin plated Insulation displacement contact, It complied with ANSI/TIA/EIA 568 standard. In existing modular/MS Boxes along with necessory connections as required complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work as per recommended makes of RFP.

Cat 6, Un-sheilded Information Outlet

Supply & fixing of square Faceplate for Flush / Surface Mount Information Outlets Single/Dual or Quad Aperture , material should be PC+ABS body, Suitable for RJ45 unshielded/shielded connection modules. Should match with I. O. Dimensions should be 86mm X 86mm as required complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work as per recommended makes of RFP.

Single Aperture

Interactive Display65' with mounting kit Approved Makes:- Hikvision, samsung, Sony .For additional technical parameters of products/ work as per recommended makes of RFP.

Water Purifier

Providing and fixing Kent or Equivalent water fountain chillar cum inbuilt RO water purifier with cooling capacity 30 Ltr per hour@ 14-22 degree C and no of faciets to be 2 (1 cold+ 1 normal)

Fire Detection Services:

Supplying and drawing FRLS PVC insulated & unsheathed flexible copper conductor as per specification for electrical Works with ISI marked (IS:694) and as per IS 8130 : 2013 of 1.1 kV grade . Wire should be made from 99.99% purity copper, class 5 stranding in acc. to IEC 60228. FRLS PVC insulation which provides better fire retardant properties then normal PVC & also emits Low Smoke in case of fire & use type A insulation PVC, in existing conduit including , all as per pre approved by Engineer in charge,making connections, etc. as required. As per recommended makes of RFP

2 x 1.5 sq.mm

SITC Conventional Optical type Smoke Detector with mounting base, LED etc. as required.

SITC of conventional type Manual call point complete with Glass, hammer and chain etc. as required.

SITC 6 watt Speaker mounted in M S sheet box with perforated front mesh for PA and Emergency System.

SITC of wall / floor type following zone (each zone accessing minimum 20 units (detectors/ devices ) Conventional Type microprocessor based with LCD display main control panel/ floor panel fabricated from 16 SWG CRCA sheet steel sealed maintenance free (SMF) batteries of min2X7AH of 12 V or as required.

Specification: (i) Three Form-C relays (1 Fire, 1 Fault and 1 Fire/Fault 2 Amps@30VDC (ii) 1 On-board NACs operating @ 0.5 A/circuit (iii) Aux Output : 24 VDC (iv) Sounder Output : 24 VDC (v) Feature Detection Circuits: 4 Zones ( upto 20 Detectors + 5 MCPs) (vi) Zone wise Fire, Fault , Disable indication (vii)Panel keys : Silence Buzzer/ Alarm, Reset, Navigation keys (Left, Right, Down, Menu/Ok) (viii) Lamp Test & Walk Test (ix) Standby power 24V DC (2 no's of 12V, 7Ah Lead Acid Battery) (x)Certification (CE, LVDE) (xi) Event Log- 1200 events (xii) Earth fault monitoring

User Interface: Display:16 X 2 character LCD Control Keys:Menu/Ok, Silence, Navigation and Reset buttons Indicators:Fire, Power, Fault, NAC Fault, Earth Fault, Silence

Wiring Details: Mechanical Specifications : Construction: Cold Rolled Steel with powder coated finish with door lock Cable Entry : 08 Number x 20.50 mm knockout Electrical Specifications: Operating Voltage: 230 VAC, 50 HZ Alarm Load(Sounder) 0.5 A (max) NAC output 0.5Amp.(max) Operating Temperature : 0oC~ 49oC Relative Humidity : 5 % to 95 % non -condensing Standby Batteries : Minimum capacity (2 X12 V 2.8 Ah); Maximum Capacity (2 x 12 V 7 Ah) Detection Circuits : 2,4,zone , max 2 mA per detector class B circuit External outputs : sounder output (18.5 to 28.0 Vdc, 0.5 Amp.(max)); Auxiliary Output ( 18.5 to 28.0 Vdc, 0.5 Amp.(max))

Compatible Devices: System sensor Photo Electric Smoke Detector, System sensor Photo Electric and Heat detector, System sensor Plug-in detector base System sensor MCP Red W/O Back Box System sensor Horn cum strobe , wall , Red, Standard Candela

Supply & Fixing of ABC Type (MAP 50) type powder Fire Extinguisher (Stored Pressure type) of following capacity duly current and valid BIS certification conforming to IS: 15683:2006, with Dry chemical powder used as extinguishing agent should be Mono Ammonium Phosphate 50% concentration conforming to IS 14609:1999.Serial no. and date of manufacturing should be embossed or printed on the body of the fire extinguisher. All as per pre approved by Engineer in charge.

INTERMARC

ADROIT INTERIORS

Eminent Colonizers Private Limited

PAVILIONS AND INTERIORS INDIA PRIVATE LIMITED

ADROIT INTERIORS

Eminent Colonizers Private Limited