Certain repairs / maint work to roofs joinery sanitary fittings plastering sunken floors and certain other comprehensive maint work for MES Staff Qtrs in the area AGE B/R II under GE (N) Ahmednagar

Amount

Dismantling of stone slabs and tiles of any description or thickness in floors, approns etc laid and bedded in any mortor all as directed.

Demolition of plain cement concrete (unreinforced) in ground floor not exceeding 15 cm thick etc complete all as specified and directed by Engineer-in-Charge

M & L in repair for precast PCC solid block masonry type C1 of (1:3:6) using 20 mm graded stone aggregate exc 10 cm in width built in cement and sand mortar (1:6) etc complete all as specified and directed by Engineer-in-Charge

M & L in repair for rough dressed shahabad stone, 25 mm to 40 mm thick laid over and including 15 mm thick screed bed in cement and sand mortar (1:6), laid and jointed pointed in cement and sand mortar (1:3) etc complete all as specified and directed by Engineer-in-Charge

Material and labour for Anti skid ceramic coloured tiles to match dado tiles makes as specified in PS,7-8 mm thick as approved by GE (square / rectangular) area of each tile exc 0.06Sqm but not exc 0.11 Sqm, as in floor etc laid over and including screed bed 15 mm thick in cement and sand mortar (1:6) set and jointed with white or coloured cement to match the shade of tiles etc complete all as specified and directed by Engineer-in-Charge

Material and labour for joint free / rectified ceramic coloured tiles SSR series of Johnson/ FT series of orient/bell/Duro cotto series of Nitco equivalent in kajaria makes as specified in PS, 7-8 mm thick as approved by GE (square / rectangular) area of each tile exc 0.18 Sqm but not exc 0.38 Sqm, as in floor etc laid over and including screed bed 15 mm thick in cement and sand mortar (1:6) set and jointed with white or coloured cement to match the shade of tiles etc complete all as specified and directed by Engineer-in-Charge

All as per item No 06 (here-in-before) but in skirting over 10 mm thick rendering in cement and snad mortar (1:4)

Material and labour for coloured glazed ceramic tiles digitally printed premium designer series of size exc 0.12 Sqm and n'exc 0.18 Sqm , 8-10 mm thick as approved by GE as in dado/skirting or on vertical surfaces, over and including 10 mm thick backing coat in cement and snad mortar (1:4) set and jointed in neat cement slurry and pointed in white or coloured cement to match etc complete all as specified and directed by Engineer-in-Charge

Material and labour 16 to 18 mm thick pre-polished granite stone slab of approved shade and colour Jet Black / Telephone Black as in top table, top of WHB, kitchen slab/platform, steps, gate pillars, cills etc or on vertical surfaces including vertical projection, full round moulding the edge laid over screed bed 15mm thick in cement and sand mortar (1:4) jointing , pointing in white cement (1:2) using marble dust with admixture of pigment to match the shade of granite and rubbing polish to achieve mirror finish complete all as specified and directed.

Material and labour machine cut cudappah stone slab 20-25 mm thick over cement screed base, full round moulding the edge laid over and including 15 mm thick screed bed in cement and sabd mortar (1:6), set and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing etc complete all as specified and directed by Engineer-in-Charge

Material and labour for 60-62mm thick, PCC pavers interilocking tiles 25x25x25mm thick of glossy finish, any shape & size conforming to IS 15658 of 2006 M35 grade made up with 12.5mm graded mahically crushed stone aggregates, factory made over and including 30mm thick sand cushioned and joints filled with line sand including levelling & sweeping etc complete all as specified and directed by Engineer-in-Charge.

M & L for chequerred cement concrete tiles with pigment 20cmx20cmx25mm thick, set, jointed and pointed in neat cement slurry in floors above screed bed of 15mm thickness in cement and sand mortar (1:6) etc complete all as specified and directed by Engineer-in-Charge

M & L for 75 mm thick Cement concrete (1:4:8) type D2, (using 40 mm graded stone aggregate) as in sub base etc complete all as specified and directed by Engineer-in-Charge

Material and labour for plain cement concrete (1:4:8) type D2, using 40 mm graded stone aggregate as in foundation etc complete all as specified and directed by Engineer-in-Charge

M & L for PCC type (1:2:4) B0 (using 12.5 mm graded stone aggregate) as in copings including weathering, slightly rounded or chamfered angles and throating etc complete all as specified and directed by Engineer-in-Charge

Taking down chowkhats or frames not exc 1.50 Sqm with shuttes (without taking off shutters from the frames) etc complete ll as specified and directed by Engineer-in-Charge

Taking down chowkhats or frames exc 150 Sqm and not exc 4 Sqmwith shutters (withour taking off shutter from the frames) etc complete all as specified and directed by Engineer-in-Charge

Taking down shutters of any description exc 1 sqm but not exc 2 sqm each etc complete all as specified and directed by Engineer-in-Charge

Supply and fix pressed steel frames of size 105 mm X 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc. all as directed.

All as per item No 19 (here-in-before) but pressed steel frame of size125 mm x 60 mm complate all as specified

Supply and fix solid PVC door frame made out of PVC section size 40 mm X 48 with special polymeric reinforcement at necessary places to hold the screw all square tube, etc complete all as specified and directed by Engineer-in-Charge.

Supply and fixing PVC Door Shutter frame & infill panel made from PVC material conforming to IS 10151;1982. The shutter frane shall be made out PVC extruded section having overall dimensions of 100mm x 30mm with two self extruded grooves at 40 mm & 50 mm on front surfaces.The infill panel shall be made out of multi chambered seamless hollow PVC extruded panel having 20mm thickness. The shutter frame shall be mitre cut & jointed at corners by means of polymeric corners. all the hardware locations shall be reinforced with special polymeric bars. etc complete all as specified and directed by Engineer-in-Charge

Supply and fix windows double shutters including box/projecting type hinges with steel handle, and steel peg stay, complete with guard bars, dovetailed or welded etc complete all as specified and directed by Engineer-in-ChargeNote: Rate quoted is deemed to be included for scaffholding etc reqd upto 7.50 m height

Supply and fix steel ventilator with top hung shutter including hinges, steel peg stay all as directed.NOTES: 1) Guard bars shall be measured and paid separately as supply only. 2) M & L for galzing shall be measured and paid separately. 3) Rate quoted is deemed to be included for scaffholding etc reqd upto 7.50 m height etc complete all as specified and directed by Engineer-in-Charge

S&F mild steel square guard bars 10 mm welded to steel windows / ventilators etc complete all as specified and directed by Engineer-in-Charge

Supply and fix 35 mm thick 2nd class hardwood factory made plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial plywood . The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated etc complete all as specified and directed by Engineer-in-Charge

Supply and fix 35 mm thick 2nd class hardwood factory made glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a) etc complete all as specified and directed by Engineer-in-Charge

Supply and fix 30 mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides etc complete all as specified and directed by Engineer-in-Chage

Supply and fix 300 mm long mild steel sliding door bolts, plate type, stove enamelled black with bright bolt, not less than 12 mm dia with and including a minimum of 6 bolts and nuts, four on blot plate and two on staple plate etc complete all as specifie and directed by Engineer-in-Charge

Material and labour for filling in door frames in plain cement concrete, (1:2:4) type B0, using 12.5 mm graded stone aggregates etc complete all as specified and directed by Engineer-in-Charge

Supply and fix galvanised mild steel wire cloth 0.50 nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanised wire staples etc complete all as specified and directed by Engineer-in-Charge

Supply and fixing in repair galvanised mild steel wire cloth 0.50 nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanised wire staples etc complete all as specified and directed by Engineer-in-Charge

Supply and fix Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed type type C-21 complete all as specified. weight cold rolled of size 75 mm etc complete all as specified and directed by Engineer-in-Charge

Supply and fix aluminium alloy, anodised, sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded section of cast aluminium alloy and fixed 200 mm long etc complete all as specified and directed by Engineer-in-Charge

Supply and fix aluminium anodised barrel tower bolt of extruded section 200 mm long etc complete all as specified and directed by Engineer-in-Charge

Supply and fix aluminium anodised barrel tower bolt of extruded section 150 mm long etc complete all as specified and directed by Engineer-in-Charge

Supply and fix aluminium anodised handles of extruded section 150 mm long etc complete all as specified and directed by Engineer-in-Charge

S & F Mild steel 300 mm ordinary rat tail rod pattern springs, including roller plate etc complete all as specified and directed by Engineer-in-Charge

All as per item No 38 above but fixed in repairs etc complete all as specified and directed by Engineer-in-Charge

Taking down cement plaster on brick / stone walls including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed by Engineer-in-Charge

M & L for rendering, 10 mm thick on stone/brick /PCC block or concrete surfaces in cement and mortar (1:4) surfaces finished even and smooth without using extra cement etc complete all as specified and directed by Engineer-in-Charge

Supply and fix in repairs vitreous China white squatting pan, Orissa pattern of size 580 X 440 mm width with integral foot rest set in cement concrete including flush pipe and connecting to trap / flushing cistren complete all as specified and directed.Make :- Cat Part No C0117 Of Parryware or Cat Part No 20042 Of Hindware or equivalent in makes mentioed in list of makes in Appendix `C'

Supply and fix in repairs wash hand basin vitreous China white, flat back type of size 550 X 400 mm pedastal type including pedastal, CP waste chain and plug and porcelain stopper, waste pipe, a pair of brackets,or errecting stand and PVC connection all as specified and directed. Make :- Cat Part No 10098 of Hindware or equivalent in makes mentioned in list of makes in Appendix `C'

Supply and fix sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with Plugs, washers and waste: including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipr overall size 915mm x460mm bowl size 410mm x 330mm x 160mm etc complete all as specified and directed by Engineer-in-Charge

Supply and fix fancy type CP bib taps, 15 mm dia, cast copper alloy with crutch or butter fly handle screwed down for iron pipe or for brass ferrule etc complete all as specified and directed by Engineer-in-Charge

Supply and fix in repairs bib tap, 15 mm dia, cast copper alloy chromium plated fancy type with capstan head screwed down for iron pipe or for brass ferrule all as directed Make :- Cat part No MOR 1020A(Orintal series) of Marc of equivalent in makes mentioned in list of makes in Appendix `C'

Supply and fix in repairs, stop valve, 15 mm dia, cast copper alloy, chromium plated, screwed down high pressure with capstain head screwed both ends for iron pipe or for unions all as directed Make :- Cat part No MOR 1320(Orintal series) of Marc of equivalent in makes mentioned in list of makes in Appendix `C'

Supply and fix in repair 15 mm dia pillar tap, cast copper alloy, with capstan heads, chromium plated, fancy type, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe all as directed Make :- Cat part No MOR 1010A(Orintal series) of Marc of equivalent in makes mentioned in list of makes in Appendix `C'

Supply and fix in repairs, Brass chromium plated shower rose 125 mm size with or without swivel joints any size including fixing to steel pipe or union etc complete all as specified and directed by Engineer-in-Charge

Supply and fix in repairs looking mirror of size 600 - 700mm X 450 - 500 mm all as directed Make :- Cat part No C8606 of Parryware or equivalent in makes mentioned in list of makes in Appendix `C'

Filleting in any position and any shape in cement and sand mortar (1:4) including mitered stop etc sectional area of fillets not exc 10 sq cm as in for dado/ skirting top etc complete all as specified and directed by Engineer-in-Charge

S & F in repairs CP curtain rod with decorative brackets etc complete all as specified and directed by Engineer-in-Charge

Supply and fixed in repairs 32 mm dia PVC waste pipe (outlet pipe) plain fixed to waste coupling of WHB or Sink etc all as directed.

Supply and fix rotational moulded polyethylene water storage tanks double layer ISI marked conforming to IS 12701-1996 (cylindrical vertical with closed top) and made out of virgin FDA approved polyethylene material of 500 litres capacity hoisted and fixed in position including 20 mm dia ball valve, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed to iron pipe and connecting complete all as specified and directed.

All as per item No 54 (here-inbefore) but 1000 ltrs etc.

Material and labour for two coats of synthetic enamel paint over a coat of pink primer for new/old wooden surfaces of any description exc 10 cm width or girth including preparation of surfaces and smooth finish with roller etc complete all as specified and directed by Engineer-in-Charge

Material and labour for two coats of synthetic enamel paint over a coat of red oxide primer for new/old steel surfaces of any description exc 10 cm width or girth including preparation of surfaces etc complete all as specified and directed by Engineer-in-Charge

Hacking out old broken glass (any thickness size,quality or description) from wooden/Steel frames or stone, concrete or brick surrounds glazed with putty or fixed with beads n'exc 0.5 Sqm in each pane incl fixing 3 mm thick sheet glass ordinary quality and glazing with oil putty in suqare n.exc 0.5 sqm in each pane etc complete all as specified and directed by Engineer-in-Charge

All as per item No 58 (here-in-before)) but figured glass pin head type etc complete all as specified and directed by Engineer-in-Charge

Material and labour for glazing with 3 mm thick sheet glass ordinary quality and glazing with oil putty in square not exc 0.50 sqm in each pane etc complete all as specified and directed by Engineer-in-Charge

Material and labour for figured glass, pin headed 3 mm thick sheet glass ordinary quality and glazing with oil putty in square not exc 0.50 sqm in each pane etc complete all as specified and directed by Engineer-in-Charge

M&L for Preparing newly plastered surfaces and applying two coats of oil bound distemper on wall including smooth roller finish etc complete all as specified and directed by Engineer-in-Charge

M&L for preparing newly plastered surfaces and applying two coats of white wash on ceiling including smooth roller finish etc complete all as specified and directed by Engineer-in-Charge

M&L for Preparing newly plastered surfaces and applying two coats of cement paint on walls etc complete all as specified and directed by Engineer-in-Charge

M&L for Preparing new wooden surfaces and applying two coats of syntheic enamel paint over a coat of pink primer etc complete all as specified and directed by Engineer-in-Charge

M&L for Preparing newsteel surfaces and applying two coats of syntheic enamel paint over a coat of red oxide primer etc complete all as specified and directed by Engineer-in-Charge

Material and labour for false ceiling with Vinyle faced Arm-Gyp-FB, ceiling 600 x 600 x 9mm thick with washable metallized polyster foil backing with Vinyle covered edges, supporting sections shall be of suitable size from same makes embossed on sections and level adjuster duly suspended by 2 mm dia GI wire fixed to roof at 600mm centre to centre incl dismantling boarding any description fixed in any position with nails/screw as per manufacturere's instructions / specification and etc complete all as specified and directed by Engineer-in-Charge

Supply and fix repairs PVC valveless, syphonic action type, flushing cistern,low level, all accesories etc complete all as specified and directed by Engineer-in-Charge. Make :- Sleek essence series Of Hindware or Cat part No E8303 Of Parryware or equivalent in makes mentioned in list of makes in Appendix `C'

Supply and fix in repair PVC connections 15 mm size with PTMT nuts of length 600 mm etc complete all as specified and directed by Engineer-in-Charge

M & L for Taking up or down steel tubing 15 mm bore of pipes and connections, including cleaning for re-fixing etc complete all as specified.

M & L for Taking up or down steel tubing 20 mm bore of pipes and connections, including cleaning for re-fixing complete all as specified.

M & L for 16 mm outer dia of Pipe 3 Layer PP-R Polypropylene random copolymer concealed pipes SDR 7.4 (PN - 16) uv stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fitting fixed complete to walls, ceilings or in floors etc complete all as specified and directed by Engineer-in-Charge

M & L for 20 mm outer dia of Pipe 3 Layer PP-R Polypropylene random copolymer concealed pipes SDR 7.4 (PN - 16) uv stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fitting fixed complete to walls, ceilings or in floors etc complete all as specified and directed by Engineer-in-Charge

Supply and fixing in repairs PVC (SWR) pipe 110/100mm bore single socketed in any length with rubber ring fixed to wall/laid in trenches or in floors with approved solvent/adhesive including neceassry stack clamps etc complete all as specified and directed by Engineer-in-Charge

All as per srl item No 74 above but 75 mm bore

Supply and fixing PVC (SWR) bends any radius, for 110/100 mm bore of pipe fixed with approved solvent/adhesive fixed to walls or in floors complete all as specified and as directed.

All as per srl item No 76 above but 75 mm bore

Supply and fixing PVC (SWR) 110mm bore 'T' equal or unequal etc complete all as specified and directed by Engineer-in-Charge

S & F in repair 100 mm dia CP grating etc complete all as specified and directed by Engineer-in-Charge

Dismantling of plain or corrugated steel sheeting, any gauge, thickness, including ridge etc complete all as specified and directed by Engineer-in-Charge

S&F Pre-painted galvatume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall,fixed with self tapping screwsaas specified etc complete all as specified and directed by Engineer-in-Charge

Supply and fix 0.50 mm thick plain, galvanised, mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275 etc complete all as specified and directed by Engineer-in-Charge

S & F in repair rolled steel sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates Fe 410 (Gde-E- 250) quality-A etc complete all as specified and directed by Engineer-in-Charge

Supply and fix in repairs framed work such as in doors or gates of angle or other section with gusset plates, rails, braces, etc, complete, drilled for fixing of steel sheeting or other coverings, doors etc to be prepared for handing or sliding with and including either hooks and hinges or steel hanging door fittings ( exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing etc complete all as specified and directed by Engineer-in-Charge

An amount of Rs 74,475.00.00 shall be deducted from BOQ on account of schedule of credit

MS. G.A. CONSTRUCTION

Neha Enterprises

M/s.Abhay Kulkarni and Associates