SPECIAL REPAIR TO BLDG NO P-44 (OFFRS MESS) UNDER AGE B/R-I OF GE (N) MAMUN

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) n.exc 1.5 sqm complete all as specified and directed.

Taking down chowkat or frame with shutters (without taking shutter from the frame) exceeding 1.5sqm and not exceeding 4.00 sqm each complete all as specified and directed.

Refixing shutters of any description exceeding 1.00 Sqm and not exceeding 2.00 Sqm each in same opening, complete all as specified and directed.

Taking down cement plaster on brick walls or stone walls of any description etc including raking out joints, hacking for key, scrubbing down with water etc, rubbish off the premises, complete all as specified and directed.

Demolition of cement concrete (unreinforced) of any description and in any position not specifically provided for, complete all as specified and as directed.

Demolition of cement concrete (reinforced) of any description and in any position not otherwise specifically provided for( reinforcement cut as required to facilitate demolition) and rubbish off the premises, complete all as specified and directed.

Demolition of brick work or stone masonay built in cement mortar including all quoins, arches, pillars etc but excluding ashlar facings, dressed stonework and precast concrete articles and removal of debris/rubbish off the premises etc complete all as specified and directed.

Dismantling plain or corrugated steel sheeting , any gauge and thickness, including Nainital or similar pattern roof coverings, complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding but not backing, removing serviceable tiles to store and rubbish off the premises,complete all as specified and directed.

Taking up or down steel tubing 15mm dia and connections, including cleaning for refixing or removal to store, complete all as specified and as directed.

Taking up or down steel tubing 20mm dia and connections, including cleaning for refixing or removal to store, complete all as specified and as directed.

Dismantling structural steel work including doors, gates but excluding framed truss etc., complete all as specified and directed.

Precast reinforced cement concrete 1:2:4, type B-1 (using 20mm graded crushed stone aggregate) as in cover slab for MH / septic tank etc, set in CM 1:4 including necessary form work, complete all as specified and directed. Note :- Reinforcement shall be measured and paid seperately under respective items.

RCC 1:2:4 type B-0 (using 12.5mm graded crushed stone aggregate) as in Slabs supported on walls, beams and columns in floors roofs, landings, balconies, canopies, deck slabs and in shelves and the like including necessary formwork, complete all as specified and directed.

Brick work with fly ash (Old Size bricks) sub class 'B' bricks straight or curved on plan, exceeding 6m mean radius with old size bricks, built in cement mortar 1:6, complete all as specified and as directed.

Brick work with old unserviceable bricks retrieved from dismantling straight or curved on plan, exceeding 6m mean radius with old size bricks, built in cement mortar 1:4, complete all as specified and as directed.

Brick work with fly ash bricks (Old Size bricks), sub class'B' bricks straight or curved on plan to any radius as in half brick thick walls, built in CM 1:4, complete all as specified and directed.

5mm thick rendering on concrete surface of ceiling, chajjas, soffits of slabs etc. in CM 1:3 finishing the surfaces even and smooth without using extra cement, complete all as specified and directed.

10mm thick rendering on fair faces of brick work or concrete surfaces in CM 1:6 finished the surface even and smooth without using extra cement, complete all as specified and directed.

15mm thick rendering cement plaster in two layers (10+5mm) on fair faces of brick work or concrete surfaces in cement mortar (1:4) finished even and smooth without using extra cement complete all as specified and directed.

20mm thick cement plaster in cement mortar 1:4 on concrete surfaces, finished even and smooth using WPC liquid as per manufacturer instruction @ 0.200 ltr in 50 Kg of cement, complete all as specified & directed.

10mm thick rendering on fascia / edging / ceiling of Chajjas, roof projections etc, making the edges in line, in true shape in CM 1:3 and finishing the surface without using extra cement, complete all as specified and directed.

Supply only liquid water proofing compound, complete all as specified and directed.

Preparation of surfaces and applying first coat of fiber reinforced elastomeric liquid water proofing membrane formulated with PU hybrid polymers and reinforcing acrylic fibers with Sun Reflective Index (SRI) of 100-110, having minimum elongation of 350%, tensile strength of 2.9 Mpa and shall have cracks bridging ability upto 2.5mm and shåll resist 10 bars of hydrostatic pressure & reduce surface temperature upto 10 degree Celsius with 33% dilution of priming coat. Laying of fiber mesh of 0.3mm thickness weave in leno pattern having 45 gsm/sqm and pasting it properly with overlap of 50mm and allow it to dry, applying second of undiluted coat @ 0.45 Itr/sqm. Applying third and final coat undiluted @ 0.45 ltr/sqm complete application to be done by the manufacturer or authorised applicator, complete all as specified and directed.

Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ceosetory windows & other Frames/chowkhat of size 65x100mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

Pressed steel frames for doors/windows of size size 125x60 mm (1.25mm thick MS sheet) with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc, duly filling of cement concrete 1:3:6 type C-0 (using 12.50 mm graded crushed stone aggregate) to back of chowkhats, including two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified and directed.

Pressed steel frames for doors/windows of size size 105x60 mm (1.25mm thick MS sheet) with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc, duly filling of cement concrete 1:3:6 type C-0 (using 12.50 mm graded crushed stone aggregate) to back of chowkhats, including two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified and directed.

35mm thick factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, complete all as specified and directed. (Note: stainless steel butt hinges and necessary S S screws shall be paid separately).

35mm thick, 2nd class hardwood (Sal/ Hollock) factory made, plain framed, panelled shutters (two panels) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneers on both faces, the size of rail and stile as per IS-1003 (Part-I), kiln seasoned and chemically pressure treated, fitted to chowkats, complete all as specified and directed.

35mm thick, 2nd class hardwood (Sal/ Hollock) factory made glazed and skeleton shutters, open rebated and prepared to receive glass or gauge,etc., edges of framing plain, divided into squares with plain chamfered or rounded, mitred and rebated sash bars, any numbers, fitted with cut & mitred beads for securing gauge sizes of members of shutters as specified in SSR Part-I Section-8, clause 8.24 (a) for door shutter supplying and fitted to chowkats, complete all as specified and directed.

Box type Steel windows comprised of tubular frame and shutters made out of 1.25mm thick MS steel tube factory made with double side shutters wire gauged shutter & glass glazed shutter (wire mesh and sheet glass shall be measured and paid separately) with side hung shutters with steel handle and steel peg stay dovetailed or welded including 2 Nos tower bolts 150mm long for each leaf and 10mm square bar grills at spacing as shown on drg welded to FI frame work, including other fittings, hinges, handles, tarred hold fasts, PCC blocks (1:2:4 type 12.50mm graded crushed stone aggregate) including two coats of synthetic enamel paint over a shop coat of red oxide primer etc. all as shown on drg No CEPZ /TD-354/09 sheet 1/3 to 3/3 and making good to disturbed area in same finish, complete all as specified and directed.

Powder coated (minimum thickness of powder coating 50 micron) anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc., complete all as specified and directed.

Powder coated (minimum thickness of powder coating 50 micron) anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long-1 No, hinges type B-21 100mm long-2 No. suitable handle-1 No, complete all as specified and directed.

Pre-painted galvalume aluminium zinc coating GI based (AZ150) corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering /cladding to wall, fixed with self tapping screws as specified and directed.

Pre-painted galvalume aluminium zinc coating GI based (AZ150) plain steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering /cladding to wall, fixed with self tapping screws as specified and directed.

17-18mm thick factory made single extruded WPC board, one side prelaminated sheet and other side wood nature colour for kitchen cabinet/cupboard of density 600 Kg /Cum with 100% termite/water proof, fire retardent, Eco-friendly and finish at all level for making edges lipping using binding tape etc., fixed in repair, complete all as specified and directed.

5mm thick factory made single extruded WPC board, one side prelaminated sheet for kitchen cabinet/cupboard of density 600 Kg/Cum, complete all as specified and directed.

300mm size aluminium alloy, anodised, sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy, complete all as specified and directed.

100mm long, mild steel cold rolled butt hinges, medium weight, complete all as specified and directed.

200mm long, aluminium, anodised, barrel tower bolts of extruded section, complete all as specified and directed.

150mm long, extruded aluminium alloy handles, fabricated type, anodised, complete all as specified and directed.

150mm long, stainless steel handles with bright finish, ISI marked fixed with nut and bolt /screws, complete all as specified and directed.

Telescopic type Side channel of drawer of standard size including roller for moving drawer made out of mild steel bright finish or electro-galvanised (soft close ball bearing runners) with width of flap 30mm & 60mm long complete all as specified and directed.

300mm mild steel ordinary rat tail rod pattern springs including roller and roller plate, complete all as specified and directed.

100mm hasp and staple, safety type, aluminium anodised fancy type including bolt to hinge plate and fixed with screws, complete all as specified and directed.

2nd class hard wood (wrought) Small fittings such as brackets of any type, latch and hinge blocks, shaped door and window stops and the like, including all necessary labours; articles n exc 200 cu. cm each, complete all as specified and directed.

Stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperature 1.40 mm and fixed with stainless steel wire staples,complete all as specified and directed.

3mm thick figured/frosted glass ordinary quality, and glazing with oil putty or fixed with bead/glazing pins in squares n.exc 0.50 Sqm in each pane, complete all as specified and directed.

3mm thick sheet glass ordinary quality, and glazing with oil putty or fixed with bead/glazing pins in squares n.exc 0.50 Sqm in each pane, complete all as specified and directed.

5.50mm thick sheet glass ordinary quality, and glazing with oil putty or fixed with bead/glazing pins in squares exc 0.50 Sqm in each pane, complete all as specified and directed.

12mm toughned glass as in hinged doors, partitions automatic doors and similar work including cutting to shape, drilling holes required, complete all as specified and directed.

25mm bore stainless steel, single curtain rod (wall thickness not less than 1mm) with fancy type/ornamental stainless steel brackets and ends finials fancy type, fixed in position with PVC plugs & 75mm SS screws, fixed in repair, complete all as specified and directed.

Rolled sections in framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete, conforming to Fe-410-W (Gde-E-250) quality-A, complete all as specified and directed.

MS TMT bars 10mm dia and over cut to length, bent to shape required, including cranking bending spirally for hopping for columns, hooking ends and binding with and including mild steel wire (annealed) not les than 0.9 mm dia or securing with clips quality conforming to complete all as specified and directed.

Formwork to sides and soffits of suspended slab such as roof slab, floor slab, shelves and similar works n. exc. 200mm thick (Horizontal or sloping), finishing the concrete surfaces rough, complete all as specified and directed.

PCC 1:2:4 type B-0 ( using 12.5 mm graded crushed stone aggregate) in roof padding in slope/ to maintain levels, surface finished even and smooth without using extra cement complete all as specified and as directed.

75mm thick PCC 1:4:8 Type D-2 (40 mm graded stone aggregate) as in sub-base of floors, sub-bases, floors, pavings etc, complete all as specified and directed.

PCC type C-1, 1:3:6 (using 20mm graded crushed stone aggregate) as in plinth protection 75mm thick laid in slope finished even and fair including making joints not more than 2.5 m (or as directed) and at corner, filled with bitumen 85/25 and sand in ratio 1:2 by weight complete all as specified and directed.

10mm thick vitrified tiles, light shade (square/rectangular) polished, area of each tiles not exceeding 0.36 sqm in floors etc. set and jointed joint free in neat cement slurry and pointed in white or coloured cement to match and including 15 mm thick screed bed in cement mortar 1:4 to recieve the tiles, complete all as specified and directed.

10mm thick vitrified tiles, light shade (square/rectangular) polished, area of each tiles not exceeding 0.36 sqm as in vertical surfaces such as skirting dado etc set and jointed joint free in neat cement slurry, pointed in white or coloured cement to match over and including 10mm thick rendering in cement mortar 1:4 to receive tiles, complete all as specified and directed.

Non skid ceramic coloured tiles 7 to 8 mm thick area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in floors etc set and jointed (joint free) in neat cement slurry and pointed in coloured cement over 15mm thick screed bed or bedding layer of mortar in CM 1:4 and dismantling floor, hearth or walls tilling and terrazo topping including cement mortar bedding ( but not backing), rubish off the premises, complete all as specified and directed.

Glazed ceramic coloured tiles 300mm x 600mm x 7-8mm thick as in vertical surfaces such as skirting dado etc set and jointed in neat cement slurry, pointed in white or coloured cement to match over and including 10mm thick rendering in cement mortar 1:4 to receive tiles and dismantling floor, hearth or walls tilling and terrazo topping including cement mortar bedding ( but not backing), rubish off the premises, complete all as specified and directed.

Baislana zebra marble work 12-15mm thick (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like over 15mm thick cement mortar (1:4) including cutting moulding, polishing and pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade including round chamfering to the edges not exc 15 mm wide, complete all as specified and directed.

20-25mm thick machine cut kota stone slab flooring over 20mm thick screed bed in cement mortar 1:6 base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing, complete all as specified and directed.

12mm thick heavy duty Industrial tiles (sqaure/rectangular), area of each tile exc 0.08 sqm but n exc 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in coloured cement to match the tiles laid over and including 15 mm thick screed bed or bedding layer mortar in CM 1:4 including dismantling of old tiles of any description with bedding layer of mortar and removal of rubbish complete all as specified and as directed.

80mm thick factory made machine pressed precast concrete, coloured interlocking paver block with cement and coloured pigment (topping thickness not less than 5mm thick with white cement and non-fadable epoxy coated colour pigment), any shape, size and design as approved by Engr-in charge confirming to IS 15658-2006, M-40 grade, complete all as specified and directed.

15mm bore Steel water tubing, galvanised, "medium grade" with all fittings and fixtures and short lengths, fixed to wall and ceiling or laid in floor, complete all as specified and directed.

Refixing of old steel tubing 15mm bore and connection in old or new position (walls, ceiling or floors etc.) with new all fittings short pieces, complete all as specified and directed.

20mm bore Steel water tubing, galvanised, "medium grade" with all fittings and fixtures and short lengths, fixed to wall and ceiling or laid in floor, complete all as specified and directed.

Refixing of old steel tubing 20mm bore and connection in old or new position (walls, ceiling or floors etc.) with new all fittings short pieces, complete all as specified and directed.

Cutting chases for concealed water tubing, making good to facing where required, pointing in CM 1:3, cutting n.exc. 10cm in girth, complete all as specified and directed.

15mm bore bib tap, long nose, fancy type chromium plated cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or brass ferrule (fixed in repairs),complete all as specified and directed.

15mm bore stop valve/angel valve, chromium plated cast copper alloy, screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipe or union (fixed in repairs), complete all as specified and directed.

Brass CP centre hole basin mixer, single lever operated, fancy type for mixing hot & cold water screwed down for 15mm bore dia of pipe & suitable iron connection pipe and fixed cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe, fixed in repair, complete all as specified and directed.

15mm bore pillar tap, copper alloy with capstan head, chromium plated screwed down high pressure, with or without lettered hot/cold with long screwed shanks and fly nuts screwed for iron pipe, complete all as specified and directed.

Supply, fixing, jointing and testing, 20mm bore gun metal globe or gate valve with iron wheel head screwed head both for iron pipe & fixed in repair, complete all as specified and directed.

S&F in repair vitreous china, wash hand basin, white, flat back, of size 550mmx400mm with brackets including cutting for and pinning in ends of brackets, complete all as specified or erecting stand including 32mm full threaded waste coupling and 32mm PVC waste pipe, complete all as specified and directed.

S & F in repair vitreous china squatting pan water closet, orissa pattern, size 580x440mm white with integral foot rests (excluding flushing cistern and flush pipe) including cast iron 'P' or 'S' trap, front or back inlet and foot rests, any pattern including cement concrete bedding, complete all as specified and directed.

S & F in repairs vitreous china one piece wash down water closet pan "Pedestal" white including fixing bolts etc, making connection to trap, flush pipe and PVC seat cover white including stainless steel or aluminium anodised hinge devices including 10 litre capacity PVC valveless, low level, synphonic action type, flushing cistern, with inlet, ball valve, float valve, handle including brackets & making good to floor in cement mortar M-15 (1:2:4) type B-1 (using 20mm graded crushed stone aggregated, complete all as specified and directed.

S & F in repair 10 litre capacity PVC valveless, low level, synphonic action type, flushing cistern, with inlet, ball valve, float valve, handle including brackets including 32mm dia PVC flush pipe of suitable size and making necessary connections, complete all as specified and directed.

PVC connection 15mm size with PTMT nuts at both ends of length 450mm for hot and cold water, complete all as specified and directed.

Rotational moulded polythylene 500 litres capacity water storage tank (Cylindrical vertical with closed top), 3 layer hoisted and fixed in position including 20mm brass ball valve high pressure with brass rod & high density plastic ball including dismanting of water tanks of capacity exc 250 ltrs but not exc 500 ltrs and removing to store, complete all as specified and directed.

Rotational moulded polythylene 1000 litres capacity water storage tank (Cylindrical vertical with closed top), 3 layer hoisted and fixed in position including 20mm brass ball valve high pressure with brass rod & high density plastic ball including dismanting of water tanks of capacity exc 500 ltrs but not exc 1000 ltrs and removing to store, complete all as specified and directed.

Sinks with drainage board made of 1mm thick stainless steel kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm, fixed in repairs, complete all as specified and directed.

Preparation of new plastered or unplastered surfaces of wall and applying three coats of white wash,complete all as specified and directed.

Preparation of new plastered or unplastered surfaces of ceiling and applying three coats of white wash,complete all as specified and directed.

Preparation of old surfaces of walls plastered or unplastered and applying two coats of white wash, complete all as specified and directed.

Preparation of old surfaces of ceiling plastered or unplastered and applying two coats of white wash, complete all as specified and directed.

Preparation of new plastered or unplastered external surfaces of walls and chajjas and applying two coats of cement base paint over a coat of alkali-resistant priming paint, complete all as specified and directed.

Complete removal of old existing treatment of external surfaces of walls and applying two coats of cement base paint over a coat of alkali-resistant priming paint, complete all as specified and directed.

Preparation of new plastered or unplastered external surfaces of wall and applying applying two coats of antifungal acrylic emulsion exterior weather proof paint, complete all as specified and directed.

Preparation of new plastered or unplastered surfaces of walls and applying 3mm thick wall care putty, making the surface smooth & applying two coats of oil emulsion paint over a coat of priming paint , complete all as specified and directed.

Complete removal of old existing treatment of walls and applying 2mm thick wall care putty, making the surface smooth & applying two coats of oil emulsion paint over a coat of priming paint, complete all as specified and directed.

Preparation of old painted steel surfaces of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint, complete all specified and directed.

Preparation of new wooden surfaces of any description not otherwise described, exc 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer, complete all as specified and directed.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc., complete all as specified and directed.

Point wiring using 3x1.5 Sqmm FRLS PVC insulated unsheathed multistranded copper conductor cable 1100 Volts grade (Phase, neutral and earth wire) with proper colour coding drawn through and incl PVC rigid concealed conduit medium grade (ISI Marked) of dia not less than 20mm and 1.5mm thick and connected to common earth dolly with 1.6mm thick MS/GI pressed steel sunken box of adequate size and 3mm thick plastic laminated sheet cover fixed with brass screws complete including cutting chases grooves for concealed wiring for light/fan/bell point controlled by one switch and making good (in CM 1:4) the surface as per existing complete all as specified and directed.

All as per Ser item No 99 here-in-before but for one 5/6 Amp socket outlet points on same board controlled by one switch.

All as per Ser item No 99 here-in-before but for one 5/6 Amp socket outlet points on independent board controlled by one switch.

All as per Srl item No 99 here-in-before but for one 15/16 Amp socket point with 3x2.5 Sqmm FRLS PVC insulated unsheathed multistranded copper conductor.

All as per Ser item No 99 here-in-before but for one light point controlled by two 2 way switch, 5/6 Amp, 240 volts.

Stepped type electronic fan regulator flush type on the existing phenolic laminated sheet etc. not less than 100W as reqd., complete all as specified and directed.

Switch piano flush button single pole one way 5/6 Amp 240 volts complete all as specified and as directed.

Switch piano flush button with shutters single pole one way 15/16 Amp 240 volts complete all as specified and as directed.

Switch piano flush button single pole two way 5/6 Amp 240 volts complete all as specified and as directed.

Socket outlet 2 in 1, 3 pin, 5/6 Amps, flush type, 240 volts complete all as specified and as directed.

Socket outlet 2 in 1, 6 pin, 6/16 Amp flush type, 240 volts complete all as specified and as directed.

Ceiling rose 3 terminal bakelite 65mm x50mm surface type, PVC/ Polycarbonate, isolated body, complete all as specified and directed.

Lamp holder, PVC/ Polycarbonate type with back plate, straight/ angular suitable for batten fittings, complete all as specified and directed.

LED Lamp 12 watt, rated input voltage 220V AC, 50Hz, rated lumens 1425 lm, CRI 80, lamp life 15000 Hrs, rated efficiency 95 lm/w, surge protection 3.0 kV, 5 star rated, complete all as specified & directed.

Replacement of LED lights fitting, 1x20W, 4' long 230V, 6500 K, AC, intenso LXS LED batten, wall mounted, PF-0.95, CRI-80, 25000 Hrs life, pe-wired internally with all accessories, driver including LED tube light and connecting up with three core flexible copper conductor cable of suitable size from ceiling rose, complete all as specified and directed.

9W LED fancy type wall/surface mounted decorative light fitting with brushed nickle finish fixture and opal glass decorative diffuser, B-22 type lamp holder and wall mounting arrangment including LED lamp and connecting up with suitable size flexible copper conductor, taking down old lighting and making good disturbed surface of wall with cement mortar 1:4 and finishes to match exisiting surface, complete all as specified and directed.

Replacement of 10W bulk head LED luminaire, energy efficient wall mounted, pressure die-cast and enclosed with polycarbonated cover with all accessories including lamp, internally prewired and connecting up with suitable size flexible copper conductor cable from ceiling rose to connector of LED fitting, complete all as specified and directed.

Taking down carefully unsv copper/aluminium sub main wiring of any size including old broken steel/PVC conduit, removing materials to store for keeping in safe custody for taking credit complete all as specified.

Sub main wiring with two single core PVC insulated unsheathed multistranded flexible copper conductor cable of size 6 sqmm and one single core PVC insulated multistranded unsheathed flexible copper conductor cable green colour of size 6 sqmm as earth lead in & including concealed rigid medium grade PVC conduit medium grade not less than 25mm dia ISI marked with all accessories and making good disturbed surface of wall with cement mortar 1:4 and finishes to match exisiting surface, complete all as required at site or directed.

Replacement of VTPN DB, 4 way sheet metal enclosures double door 415 V AC, 50 Hz AC with IP 54 and IK 09 rating suitable for MCCB 160 amps, 4 pole, 16 kA with fixed magnetic and thermal setting of same make as DB making connection with suitable size copper thimbles & including cutting chases to wall for fixing DB and making good the disturbed wall surface in CM 1:4 to match the surface as per existing, complete all as specified and directed.

Replacement of MCB DB, SPN, 12 way sheet metal enclosures double door 230 V AC, 50 Hz AC with IP 54 and IK 09 rating having fully insulated copper busbar of rating 200 Amps, insulated neutral bar, earth bar and cable ties for cable management including polyuthrene gasket complete complete in all respect flushed in wall including cutting chases on wall for taking out old unsv DB and fixing of new DB and making good disturbed surface of wall with cement mortar 1:4 and finishes to match exisiting surface, complete all as specified and directed.

MCB, SPN, AC, 240 volts "C" series capacity of 32 Amps, 10kA and making connections, complete all as specified & directed.

MCB, SP, AC, 240 volts "C" series capacity of 6-32 Amps, 10kA and making connections, complete all as specified & directed.

Replacement of LED street light fitting 60 watt 230 V AC outdoor type with high pressure die-cast aluminum hosing, PC diffuser, and heat resistant complete with integrated electronic driver with high efficiency including 32mm bore GI pipe bracket mounted on wall or roof using clamps, nuts, bolts, washers, fasteners etc.complete with polycarbonated cover, IP 65/66 protection and connecting up with three core flexible copper conductor cable of suitable size, complete all as specified and directed.

1100 volt grade heavy duty XLPE cable with PVC insulated aluminium conductor served with inner sheathing of PVC tape armoured with galvanized steel strip or wire and overall PVC sheathed of size 16 sqmm nominal cross section 4.0 core laid in trenches, fixed to pole or passing through pipes including all necessary clamps, nuts, bolts washers incl taking down old unsv cable, complete all as specified and directed. Note- Earth work and protection work shall be measured and paid for separately under respective items of BOQ.

Excavation in trenches not exceeding 1.5 m wide and n.exc. 1.5 m deep for foundation of poles/stay/cable etc including getting out in any type of soil complete all as specified and directed.

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exceeding 25 cm in depth, complete all as specified and directed.

Removing excavated material n.exc. 50m and depositing where directed at a level n.exc. 1.5 m above the starting point, complete all as specified and directed.

Sand cushioning to under groudnd cables in layers of sand of 23cm thick (8cm before laying the cable and 15cm thick after laying cable) in trenches complete as specified and directed. Note: Only punned thickness of 18cm shall be measured and paid.

Bricks laid in trenches flat with width equal to length of brick for cable protection well burnt sub class 'B' laid across the cable complete all ad specified and directed.

40mm dia GI tubing, light grade with all fitting laid in trenches or fixed on wall or along pole complete for protection of electric cable/strip, complete all as specified and directed.

Earthing complete in repair with galvanized steel earth plate electrode 60cm x 60cm x 6 mm thick burried directly in ground vertically to a depth not less than 2.25 mtr deep below GL with top edge of the plate not less than 1.5 mtr below normal GL and connected to earth plate surrounded by 15 cm thick packed layers of charcoal dust and common salt and connected to earth lead GI wire 4mm dia by means of bolts, nuts, check nuts and washers of galvd iron or steel and thimbles and other end of the earth wire connected to DB and protected by galvd iron or steel pipe light grade 15 mm bore and water pipe 20mm bore GI light grade with funnel and wire mesh, including all necessary excavation and earth work PCC chamber in cement concrete 1:3:6 type C-2 and RCC cover and all as shown in electrical plate No 3 of MES schedule Pt I of 2009. Note : RCC pit cover shall be pre-cast of RCC (1:2:4) type B-I , 80mm thick reinforced with XPM weighting not less than 4 KG/sqmm in lieu of CI cover.

Please Enable Macros to View BoQ information