Loading…
Tenderkart now works inside Claude and ChatGPT: search and analyse tenders right from your chat
Loading…
Tender ID
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹39.8 LAccepted-AOC 24B JYOTISH ROY ROAD KOLKATA 700053 | KOLKATA | WEST BENGAL | 700053 | L1 | Accepted-AOC Being lowest bidder and reasonable | |
| 2 | L2₹42.1 L+₹2.0 L (4.87%)Rejected-Finance VILL SAROT PALLY PO SANKRAIL DIST HOWRAH PIN 711313 WB | SANKRAIL | HOWRAH | WEST BENGAL | 711313 | L2 | Rejected-Finance Other than lowest | |
| 3 | L3₹42.5 L+₹2.3 L (5.64%)Rejected-Finance SAPTARAG APARTMENT RAGHUNATHPUR RAA 35 V I P ROAD KOLKATA 700059 | 24 PARAGANAS NORTH | WEST BENGAL | 700059 | L3 | Rejected-Finance Other than lowest | |
| 4 | L4₹43.1 L+₹2.9 L (7.25%)Rejected-Finance | L4 | Rejected-Finance Other than lowest | |
| 5 | L5₹43.1 L+₹3.0 L (7.35%)Rejected-Finance | L5 | Rejected-Finance Other than lowest |
Tender Value
₹37 L
EMD Value
₹74,000
Closing Date
27 Feb 2023, 6:00 pmClosed
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
GE(FW) Kolkata
D9 Commissariat Road Hastings Kolkata 700022
SPL REPAIR TO DRAIN FROM CB-4 TO O-3, ADDN/ ALTN TO KINGS TOILET AT KITCHENER HOUSE AND ADDN/ ALTN OF POINT WIRING IN COMD GURUDWARA UNDER GE (FW) KOLKATA
2023_MES_579063_1
8978/FW/E8
Open Tender
Civil Works
Item Rate
180 days
GE(FW) Kolkata
Ref tender documents
7 documents required · 7 mandatory
₹500
GE(FW) Kolkata
₹74,000
16 Mar 2023
4 Feb 2023
28 Feb 2023
4 Feb 2023
27 Feb 2023
18 Feb 2023
Amount
Demolition of cement concrete (unreinforced) in ground floors and paving's not exc 150 mm thickness (above or below ground level) and removal of debris outside MOD land complete all as specified and directed.
Demolition of cement concrete (reinforced) of any description and in any position not otherwise specifically provided for and removal of debris outside MOD land and disposed off complete all as specified and directed.
Demolition of Brick Work built in Cement Mortar including all Quoins, Arches, Pillars, etc. of any descriptions, complete all as specified and as directed.
Dismantling of floor, hearth or wall tiling incl cement mortar bedding (but not backing) removing tiles from site and rubbish off the premises complete all as specified and directed.
Taking down cement plaster from brick or concrete surfaces of any description including racking out joints, hacking for key, scrubbing down with water etc complete all as directed.
Excavation in trenches n exc 1.50 m wide and n exc 1.50m depth for foundation etc or for shafts, wells, cess pits, manholes, pier holes etc not exc 10 Sqm on plan and not exc. 1.50 Metre in depth and getting out as in soft/loose Soil, complete all as Specified and as directed.
Returning filling in incl spreading , levelling , watering and well ramming in layers not exc 25 cm as in soft/ loose Soil, complete all as Specified and as directed.
Removing excavated materials not exc 50 m and depositing where directed at a level not exc 1.50 m above the starting point complete all as Specified and as directed.
M&L Brick Work with Sub-Class ‘B’ fly-ash Bricks (with Old Size Bricks), Straight or Curved on Plan exc. 6.0 Metre mean Radius, built in Cement Mortar 1:4, complete all as specified and as directed.
M&L Brick Work with Sub-Class ‘B’ fly-ash Bricks Half-Brick thick, Old Size, built in Cement Mortar 1:4, Straight or Curved on Plan to any Radius, complete all as specified and as directed.
M&L for providing Plain Cement Concrete (1:4:8) type D2 using 40mm graded stone aggregate as in foundation filling and mass concrete completed all as specified and directed.
M&L for plain cement concrete (1:2:4) type B1 using 20 mm graded aggregates in lintels upto 1.5 m clear span, cills, steps, seismic and other similar bands, plinth courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones , bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating including formwork complete all as specified and directed.
M&L rendering 15mm thick on fair faces of brickwork or concrete surfaces in cement mortar (1:4), surfaces finished even and smooth without using extra cement complete all as a specified and as directed.
M&L rendering 15mm thick on fair faces of brickwork or concrete surfaces in cement mortar (1:6), surfaces finished even and smooth without using extra cement complete all as a specified and as directed.
M&L Rendering 10mm thick, on fair faces of brick or concrete surfaces of walls in cement mortar 1:4, finished even and smooth without using extra cement complete all as specified and directed.
M&L for extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mi- treed / stopped ends etc., completed all as specified and directed.
M&L for extra for forming fair finished drain or channel 60 cm inner girth in cement concrete, using extra cement, including forms, moulds, mi- treed / stopped ends etc., completed all as specified and directed.
Grubbing up tree trunk exc 100 cm and n exc 150 cm including cutting of trunk portion protruding over ground, digging out roots, filling holes and levelling off ground, stacking of serviceable material and removing of unserviceable material to a distance n exc 50m and clearing site, completed all as specified and directed.
S&F in repair RCPC (Reinforced Cement Polymer Concrete) grating slab of size 1200 mm x 450 mm x 75 mm thick, of capacity 5 MT fixed in proper position complete as directed by Engr-in -Charge.
S&F in repair RCPC (Reinforced Cement Polymer Concrete) grating slab of size 900 mm x 450 mm x 75 mm thick, of capacity 5 MT fixed in proper position complete as directed by Engr-in -Charge.
S&F in repair RCPC (Reinforced Cement Polymer Concrete) grating slab of size 600 mm x 450 mm x 75 mm thick, of capacity 3 MT fixed in proper position complete as directed by Engr-in -Charge.
S&F in repair RCPC (Reinforced Cement Polymer Concrete) grating slab of size 600 mm x 450 mm x 50 mm thick, of capacity 3 MT fixed in proper position complete as directed by Engr-in -Charge.
Supply and laying 600 mm bore reinforced concrete pipe of Class NP-3, laid and jointed with jute & cement mortar 1:2, complete with collars all specified and as directed.
M&L TMT Bars 10 mm dia and over, cut to length, bent to shape required including cranking, bending and binding with and including Mild Steel Wire (annealed) not less than 0.90 mm, complete all as specified and as directed.
M&L for TMT bars 5 mm dia and over upto and including 10 mm dia in stirrups, spacers and binders cut to length, bent to shape required as in reinforcement and binding with MS wire (annealed) not less than 0.90 mm dia complete all as specified and directed .
M&L for Cross arms, bracings, supports, clamps and back plates fabricated from structural steel sections, including nuts, bolts, washers, welding, bending cold or hot, drilling holes for bolts, in any shape or size as indicated or directed and inclusive of one primer coat, one under coat and one finishing coat of paint, complete all as specified and directed
M&L for Use and waste of timbering as planking and strutting for excavations in trenches in soil, n exc 1.5m deep, including wales, struts, open poling boards, etc. as may be necessary and fixing and removal, complete all as specified and directed
M&L for M-25 nominal mix RCC (1:1½:3), type A-1 (using 20mm graded stone aggregate) as in foundations, rafts, footings, foundation beams, plinth beams, base of columns, basement of slabs, underreamed piles and mass concrete etc., complete all as specified and as directed.
M&L for M-25 nominal mix RCC (1:1½:3), type A-1 (using 20mm graded stone aggregate) as in slabs supported on walls, beams, columns in floors, roofs, landings, Balcones, canopies, duck slabs, shelves and like etc., complete all as specified and as directed.
M&L for M-25 nominal mix RCC (1:1½:3), type A-1 (using 20mm graded stone aggregate) as in walls, retaining walls, basement walls and like, any thickness, above top of footings, including attached pilaster and buttresses and the like etc., complete all as specified and as directed.
M&L for preparation of new plastered surfaces and applying two coats of cement base paint over a coat of primer complete all as specified and directed.
M&L for 75mm thick Cement Concrete (1:2:4) type B-2 using 40mm graded crushed stone aggregate, as in Plinth Protection, / sub bases etc. laid in alternate Bays, finished Concrete Surfaces Even and Smooth without using Extra Cement, complete all as specified and as directed.
M&L 25 mm thick pre polished coloured chequered tiles of size 300mm X 300mm, with M-40 grade, jointed & pointed in neat cement slurry with white or coloured to match the shade of tiles, laid over & incl 20 mm thick screed bed in cement mortar 1:6 complete all as specified & directed.
S&F in position, at or near ground level, factory made precast cement concrete kerb stone blocks, in M-25 grade cement concrete, fixed to the required line, level and curvature, jointed in cement mortar 1:3, including making joints with or without grooves (thickness of joints, except at sharp curves shall not be more than 5 mm) including making drainage opening wherever required complete all as specified and directed.
Supply and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand; complete all as specified and directed. (NOTE: Cost of sand cushioning is deemed to be included in the quoted rates)
M&L for mild steel in framed work such as grills, gratings, etc. with ends of bars shouldered and /or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290 Gde-E-165 all as specified and directed by Engineer-in-Charge.
M&L in repair Mild steel plain black sheet, 1.60 mm thick, in wall cladding, steel gates and similar work, cut to size, holes punched including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40mm lap joints with riveted or welded seams including bending or turning up, mitred angles as required complete all as specified and directed.
Cleaning of existing covered / uncovered (partly / semi or fully filled up) drain, of any opening width and depth by removing and re-fixing of cover-slab (wherever applicable) taking out accumulated silt, mud, earth, rubbish, vegetation etc from the drain, washing of the drain with water and removing the same at any distance where directed as directed by KMC, complete all as directed by the Engineer-in-Charge.
M&L preparation of new or previously untreated steel and iron surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and directed.
M&L for preparation of newly plastered surfaces and applying two coats of exterior acrylic emulsion weather proof paint over a coat of primer to new wall surfaces of any description, over 10cm width or girth not otherwise described, as per manufacturer's instructions, complete all as specified and as directed.
M&L Preparing new plastered surfaces of walls and applying Two Coats of Oil Emulsion distemper with roller over a coat of alkali resistant primer and applied over and including 1.5 mm thick wall putty complete all as specified and as directed.
All as per item No.41 above, but on Ceilings, complete all as specified and directed .
M&L complete removal of existing treatment on walls and applying two coats of oil emulsion distemper with roller over a coat of alkali resistant primer and applied over and including 2 mm thick wall putty complete all as specified and directed.
S&F Non-skid ceramic coloured tiles (square/ rectangular), 7 to 8 mm thick, area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, set and jointed in neat cement slurry in floors and pointed in white or coloured cement to match the shade of tiles, laid over and including 15mm thick screed bed or bedding layer in cement mortar 1:6 complete all as specified and directed.
M&L glazed coloured decorative ceramic tiles in vertical surface 300 X 600 X 8-9 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the colour of tiles, laid over and including 10mm thick rendering in cement mortar 1:3 complete all as specified and directed.
M&L for Coloured granite (of any type) work, 18-20 mm thick (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms, urinal partition and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite and making moulds on edges laid over and including 15 mm thick screed bed in cement mortar 1:6 complete all as specified and directed.
M&L for 18-20 mm thick coloured granite Slab, machine cut, as in vertical surfaces such as skirting, dado, wall cladding etc, fixed over and including 10 mm thick backing layer in cement mortar (1:3), set and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite tiles including rubbing and polishing complete all as specified and directed..
M&L 10 mm thick Toughened glass as in hinged doors, partitions, windows, automatic doors and similar work including cutting to shape, drilling holes required, complete all as specified.
S&F double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box main body with stainless steel cover governing pivot made of brass, other part made of mild steel heavy duty complete all as specified and directed.
M&L for powder coated Anodized aluminum frame for doors, windows, ventilators and partition with one or more rebate including joining cleat for fixing etc complete all as specified and directed..
Taking down chowkhat or frames with shutters (without taking off shutters from the frame) area exc 1.5 Sqm and n.exc.4.00 Sqm each wooden all as directed.
S & F PVC solid door frame of size 50 x 47 mm made out of 5 mm thick prelaminated single side PVC sheet reinforced with MS square tube, supplying & fixing in opening as per specification & drawing shown in MES Schedule, complete all as specified and as directed.
S&F 30 mm thick factory made both side prelaminated solid panel PVC door shutter consisting of frame made out of MS tube of 19 gauge thickness and size of 19mm X 19mm for stiles, top and bottom rails, treated with a coat of metal primer, MS frame covered with heat moulded prelaminated PVC 'C' channel for stiles and both side prelaminated PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail; stiles and rails feathered at edges, panelling of both side prelaminated PVC sheet to be fitted in the MS frame welded / sealed to the stiles and rails with suitable PVC sheet beading, and joined together with solvent cement and fixing in frame complete all as specified and directed.
S&F in repair 15mm bore galvanised steel tubing (medium grade) with all fittings and fixed to walls and ceiling or laid in floors complete all as specified and directed.
S&F in repair 20mm bore galvanised steel tubing (medium grade) with all fittings and fixed to walls and ceiling or laid in floors complete all as specified and directed.
M&L for applying one coat of synthetic enamel paint to old painted steel surfaces of any description over 10 cm width or girth including preparation of surfaces complete all as specified and directed.
M&L for applying one coat of synthetic enamel paint to old painted wooden surfaces of any description over 10 cm width or girth including preparation of surfaces complete all as specified and directed.
S&F in repairs Chromium plated 25mm dia chromium plated brass curtain rod with fixing brackets, stops, rollers etc of approved design complete all as specified and directed. (NOTE: Brackets will be measured and paid separately)
Supply and fixing Brass bracket for curtain rod decorative type fixed as in repair complete all as specified and as directed.
Supply & fixing 100mm Butt hinges, cast brass, with mild steel hinge pin, bright polished and fixed, type B-11, complete all as specified and directed.
S&F 150mm long Extruded brass handles (fabricated type), polished, complete all as specified and directed.
S&F 200mm long brass barrel tower bolts with cast or sheet barrel and rolled or cast bolts and fixed, complete all as specified and directed.
S&F 200mm long Brass sliding door bolt with sand or di-cast brass hasp, staple (bolt type) and fixing bolts with rolled or drawn brass bolts and fixed, complete all as specified and directed.
S&F 140mm floor door stopper of brass body and tongue with hard drawn steel spring, complete all as specified and directed.
S&F Stainless steel sensor operated hand dryer of approved make, complete all as specified and directed.
S&F Stainless steel wall mounted tissue paper dispenser of approved make, complete all as specified and directed. Make: Jet India Cat No. JI-TDP-01 or equivalent as approved by GE.
S&F 5.5mm thick sheet glass frosted on one side, area in squares exc 0.5 sqm in each pane and glazing with rubber gasket fixed to aluminium frame work / snap beading complete all as specified and as directed by the Engineer-in-Charge
S&F Solar control film 50 micron reflective type sticked to glass panes as per instructions of manufacturer instructions, complete all as specified and as directed by the Engineer-in-Charge
S&F in repairs Vitreous China, white, half stall urinal flat back with sensor operated automatic spreader with all brass CP connected accessories like coupling, inlet nipple and waste pipe connection pipe and fixed in position as per manufacturer instructions, complete all as specified and directed. (Make & Model as approved by GE of JAQUAR / CERA/ASIAN / HINDWARE / PARRYWARE)
S&F in repairs Vitreous China, white, Counter sunk table top wash hand basin with sensor operated automatic water dispensing brass CP swan neck pillar tap as approved with all brass CP connected accessories Lile coupling, waste pipe, connection pipe etc., and fixed in position as per manufacturer instructions, complete all as specified and directed. (Make & Model as approved by GE of JAQUAR / CERA/ASIAN / HINDWARE / PARRYWARE)
S&F in repair vitreous China floor mounted coupled closet (Pedestal pattern), white, including low level vitreous China valveless symphonic action type flushing cistern with inlet ball valve float, push button, flush pipe incl bracket, P/S trap, PVC white soft close seat cover and connecting fittings complete all as specified and directed. (Make :CERA, Model : CLAIR / PARRYWARE, Model: CASCADE NXT / JAQUAR, Model: FLORENTINE / HINDWARE, Model: CONSTELLATION)
S&F in repair Chromium plated brass Towel ring (premium quality), square complete all as specified and directed. (Make : JAQUAR, Cat No: ACN-1121N / CERA, Cat No: F5002105 / ASIAN PAINTS, Cat No: SQTW201 or equivalent model in PARRYWARE / PRAYAG)
S&F Chromium plated brass Bib cock with wall flange, fancy type, long body, fixed to 15 mm bore of Iron pipe complete all as specified and directed. (Make : JAQUAR, Cat No: CON-107KN/ PARRYWARE, Cat No: G1405A1 / CERA, Model : OCEAN / PRAYAG, Cat No: 9208 /HINDWARE, Cat No: F330041)
S&F in repairs Tubular towel rail (premium quality) 20mm dia, 600mm long between flanges including brass chromium plated, complete all as specified and directed. (Make : JAQUAR, Cat No: ACN-111SM /ESS ESS, Cat No: AC-101 / PARRYWARE, Cat No: T6401A1 / CERA, Cat No: F5004103 / PRAYAG, Cat No: BA-20 /HINDWARE, Cat No: F840013)
S&F in repairs towel rack (premium quality) with lower hangar with hook complete all as specified and directed. (Make : JAQUAR, Cat No: AHS-1581H /ESS ESS, Cat No: AC-308 / PARRYWARE, Cat No: T6008A1 / CERA, Cat No: F5003101 or equivalent model in KOHLER / MARC / CRABTREE).
S&F in repair 15mm bore heavy duty PVC connector pipe of length 450 mm with PTMT coupling at both ends, screwed down for pipe as directed. (MAKE : PRAYAG, Cat No. 323 / POLYTUF, Cat No. 4003 or equivalent model in SHAKTI / JEXON / CERA)
S&F in repair 15mm bore heavy duty PVC connector pipe of length 600 mm with PTMT coupling at both ends, screwed down for pipe as directed. (MAKE : PRAYAG, Cat No. 323 / POLYTUF, Cat No. 4003 or equivalent model in SHAKTI / JEXON / CERA)
S&F in repair soap dish, Square, Acrylic body with chromium plated base, complete all as specified and directed. (Make : JAQUAR, Cat No : AKP-35731P/ PARRYWARE, Cat No.T6403A1/ ESS ESS Cat No.AC-103 /PRAYAG Cat No.BA-35 or equivalent make as approved by GE).
S&F Chromium plated brass Angular stop cock (premium quality), concealed type with wall flange fixed to 15 mm bore of Iron pipe, as in repairs, complete all as specified and directed. (Make : PARRYWARE, Cat No: G1453A1 / JAQUAR, Cat No: CON-59KN / CERA, Cat No: OCEAN / HINDWARE, Cat No: F330043 / PRAYAG, Cat No: 9020)
S&F Chromium bottle trap with internal portion 32mm size with 190mm long wall connection pipe, as in repairs, complete all as specified and as directed. (Make : JAQUAR, Cat No: ALD-769L250x190/ ESS ESS Cat No.C-231C / CERA, Cat No: F8060302 / PRAYAG, Cat No: BEA-26 / HINDWARE, CAT No: F850003)
S&F 15mm bore chromium plated two way bib cock with flange (premium quality), fancy type, as in repairs, complete all as specified and as directed. (Make : JAQUAR, Cat No: CAN-1153N / ESS ESS Cat No.C-203 / CERA, Cat No: OCEAN/ ASIAN PAINTS, Cat No: ALBC102 / PRAYAG, Cat No: 9212/HINDWARE, CAT No: F330004 / PARRYWARE, Cat No: G1434A1)
S&F toilet paper holder, surface type with flap, incl taking down existing holder, complete all as specified and directed. (Make : JAQUAR, Cat No : ACN-1153N / CERA, Cat No: F5007110 / PRAYAG, Cat No: BA-38 / ESS ESS, Cat No: AC-506 / HINDWARE, Cat No: F880003 / PARRYWARE, Cat No: T6514A1)
S&F Chromium plated toilet tumbler holder, as in repairs (incl with tumbler and chromium plated wall flange) fixing with stainless steel screws, complete all as specified and directed. (Make : JAQUAR, Cat No : CAN1141N or equivalent model in CERA / PRAYAG / ESS ESS / HINDWARE / PARRYWARE)
S&F in repair 6mm thick bevelled edge mirror of size as required fixed on 6mm thick acrylic PVC sheet complete fixed at walls with brass chromium plated camouflaged nut washers and bolt screws, complete all as specified and directed.
S&F Mono block water pressure pump set of capacity 0.5 HP single phase, discharge range 36-60LPM, working in voltage 220-240V with operating pressure range 1.4-2.4 (Bar) complete including with closed discharge valve and connected fittings, complete all as specified and directed. Make: Kirloskar-Eterna, Model - SJPBS 42420-HL or equivalent as approved by GE.
Supply, hoisting and fixing rotational moulded polyethylene water storage tank (cylindrical vertical type with closed top) of capacity 1000 Litres, multi-layered (ISI marked), with GI tank nipple & cover, hoisted and fixed in position all as specified in SSR Part-I incl dismantling of existing tank complete all as specified and directed.
SCHEDULE 'A' PART-II (ELECTRIFICATION WORKS) Taking down copper/ aluminium point wiring (light, fan, buzzer, socket or power) complete including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc for reuse or removing from site and making good disturbed surface of walls, floors etc. complete all as specified and directed.
Taking down of Old MCB DB any type any size including MCCB/RCCB/MCBs and disconnecting the serviceable MCBs and keeping in safe custody for reuse at site or removal from site complete all as specified and directed.
Taking down of old Submain wiring any type including batten/ conduit/ casing at any indicated situation complete all as specified and directed.
M&L for concealed type point wiring with 1.50 Sq. mm (nominal area) FRLSH PVC insulated and unsheathed, multi stranded copper conductor cable 1100 Volts grade, single core, laid in and including PVC conduit complete with all fittings and accessories (except terminal box and laminate cover), fixed to walls/ceiling, for mounting MODULAR TYPE switches/ regulator /bell push etc and including 1.50 Sq. mm (nominal area) FRLSH PVC insulated and unsheathed multi stranded copper conductor cable 1100 Volts grade, single core, earth continuity conductor connected to common earth dolly,. Complete all as specified and directed. for one light point / bell point/ceiling fan/exhaust fan point controlled by one way switch. (NOTE :- (i) Where tube light fitting is to be fitted/suspended, CI Circular boxes shall be provided with the PVC Pipes in the ceiling & the unit rate shall be deemed to be included for the same. (ii) Point wiring shall be measured from switch board/DB to outlets only. Main circuit wire of the switch board/DB shall be measured and paid separately as sub main wiring of required size depending upon the load of that switch board. (iii) Quoted rate shall be exclusive of the cost of terminal box and laminate cover which shall be measured separately.
All as per item No 90 here-in-before, but for one 5 pin 5/6 amp socket out let point in the same switch board of light points (except terminal box and laminate cover), fixed to walls/ceiling, for mounting MODULAR TYPE switches
All as per item No 90 here-in-before, but for one 5 pin 5/6 amps multi socket outlet point in independent board (except terminal box and laminate cover), fixed to walls/ceiling, for mounting MODULAR TYPE switches
All as per item No 90 here in before, but using 2.5 sqmm PVC insulated unsheathed multi strand copper cable (1100 V) FRLSH for line conductor and 1.5 Sqmm PVC insulated unsheathed multi strand FRLSH copper cable (1100 Volts) for earth continuity wire for one 15/16 amp multi socket out let independent (except terminal box and laminate cover), fixed to walls/ceiling, for mounting MODULAR TYPE switches
S&F Modular Switch 1 way, 6 Amps, 1 module complete all as specified and directed.
S&F Modular Switch 1 way, 16 Amps, 1 module complete all as specified and directed.
S&F Modular Socket 6 Amps, 2/3 pin combined, 2 module complete all as specified and directed.
S&F Modular Socket 6/16 Amps, 2/3 pin combined, 2 module complete all as specified and directed.
S&F Modular Fan step regulator, 120 watt, 2 module complete all as specified and directed.
S&F Modular White cover plate with frame 3 module complete all as specified and directed.
S&F Modular White cover plate with frame 4 module complete all as specified and directed.
S&F Modular White cover plate with frame 6 module complete all as specified and directed.
S&F Modular type Metal Flush box 3 module complete all as specified and directed.
S&F Modular type Metal Flush box 4 module complete all as specified and directed.
S&F Modular type Metal Flush box 6 module complete all as specified and directed.
S&F ceiling rose surface, polycarbonate/Bakelite, three terminals complete all as specified and directed.
M&L for sub main wiring with two run of FRLS-H PVC insulated & unsheathed multistranded copper conductor of nominal cross sectional area 4.0 Sqmm alongwith one run of FRLS-H PVC insulated & unsheathed multistranded copper conductor of nominal cross sectional area 4.0 Sqmm as earth continuity conductor drawn through and including PVC conduit of suitable size, surface type incl taking down existing wiring complete all as specified and directed. (NOTE : Three runs of single core 4.0 Sqmm cable & one run of PVC conduit shall be measured as one unit)
M&L for sub main wiring with two run of FRLS-H PVC insulated & unsheathed multistranded copper conductor of nominal cross sectional area 6.0 Sqmm alongwith one run of FRLS-H PVC insulated & unsheathed multistranded copper conductor of nominal cross sectional area 6.0 Sqmm as earth continuity conductor drawn through and including PVC conduit of suitable size, surface type incl taking down existing wiring complete all as specified and directed. (NOTE : Three runs of single core 6.0 Sqmm cable & one run of PVC conduit shall be measured as one unit)
Supply and Hanging, ceiling fan, with brushless DC motor, 1200 mm sweep without remote, down rod, canopy, fan blades and accessories, BEE 5 Star rated and connecting up including provision of PVC insulated, sheathed round flexible wire with multi stranded copper conductor of size 1.0 Sq mm, 3 core, 1100 Volts grade, from ceiling rose/ connector to fan including dismantling existing fan complete all as specified and directed. (MAKE : USHA, Model: TECHNOAIR / CROMPTON GREAVES, Model : ENERGION HS / ORIENT, Model: ECOTECH or equivalent model in BAJAJ / HAVELLS) NOTE: Old fan shall be deposited by contractor in MES store yard
S&F surface mounted LED luminaire, 1 X 20 Watt in aluminium housing, operating voltage 180-270 V, with acrylic/polycarbonate diffuser & integrated constant current electronic driver complete with all other accessories internally prewired and including connecting up with three core flexible copper wire of suitable size complete all as specified and directed. complying with the following specifications:- (a) minimum efficacy 110 lumen/watt (b) CRI not less than 80, (c) THD < 20% (c) having in built short circuit and surge protection (d) colour temperature not less than 5700 degree K (e) life not less than 25000 hours of operation
S&F recess mounted LED luminaire, of size 300 mm x 300 mm, in powder coated CRCA housing , having glare free diffuser, operating voltage 180-270V, with constant current electronic driver complete with all accessories with and including 18 Watt LED and including all accessories, mounting frame etc and connecting up with three core flexible copper conductor wire of adequate size complete all as specified and directed and complying with the following specifications:- (a) minimum efficacy 110 lumen/watt (b) CRI not less than 80, (c) THD < 20% (c) having in built short circuit and surge protection (d) colour temperature not less than 5700 degree K (e) life not less than 25000 hours of operation (f) Weather protection: IP20
S&F recess mounted LED luminaire, of size 600 mm x 600 mm, in powder coated CRCA housing , having glare free diffuser, operating voltage 180-270V, with constant current electronic driver complete with all accessories with and including 35/36 Watt LED and including all accessories, mounting frame etc and connecting up with three core flexible copper conductor wire of adequate size complete all as specified and directed and complying with the following specifications:- (a) minimum efficacy 110 lumen/watt (b) CRI not less than 80, (c) THD < 20% (c) having in built short circuit and surge protection (d) colour temperature not less than 5700 degree K (e) life not less than 25000 hours of operation (f) Weather protection: IP20
Supply and Fix, Double Door, Sheet Metal Enclosure for DBs (Premium range), for mounting of MCB for 240 Volts, TPN 4 way, with 200 Amps rated copper bus bar, complete all as specified and directed. (MAKE : L&T / LEGRAND /ABB / SCHNEIDER / C&S /PANASONIC/ HAGER)
Supply and Fix, Double Door, Sheet Metal Enclosure for DBs (Premium range), for mounting of MCB for 240 Volts, SPN 8 way, with 100 Amps rated copper bus bar, complete all as specified and directed. (MAKE : L&T / LEGRAND /ABB / SCHNEIDER / C&S / PANASONIC / HAGER)
NOTE FOR ITEM NO.112 & 113:- (1) Incoming MCB and outgoing MCBs shall be measured and paid separately as "Supply Only". (2) Quoted rate is deemed to be inclusive of blanking plate for slots remaining blank after fixing of MCBs. (3) DB & MCB shall be of the same manufacturer.
S&F MCB (premium range), 'C' series, TPN, 415 volts, 63 Amps, breaking capacity 10KA complete all as specified and directed. (MAKE : L&T / LEGRAND / SCHNEIDER / ABB / C&S / PANASONIC / HAGER)
S&F MCB (premium quality), 'C' series, SPN, 40-63 Amps, breaking capacity 10KA complete all as specified and directed. (MAKE : L&T / LEGRAND / SCHNEIDER / ABB / C&S / PANASONIC / HAGER)
S&F MCB (Premium Quality), 'C' series, single pole, 6 to 32 Amps, breaking capacity 10KA complete all as specified and directed. (MAKE : L&T / LEGRAND / SCHNEIDER / ABB / C&S / PANASONIC / HAGER)
S&F MODULAR MCB protected power unit with one 25 Amps socket with 3 pin plug top and including 01 No MCB, DP, and starter 25 Amps ratings with six module plate and flush metal GI box and electrically connected, as in repairs, complete all as specified and directed. (MAKE : HAVELLS, Cat No. DHDUCDP0253025 / NORTH WEST, Cat No: ACPU6M-BT or equivalent model in ABB / CRABTREE / HAGER / SCHNEIDER / LEGRAND) (NOTE : Enclosure & MCB shall be same manufacturer. Cost of MCB is deemed to be included in the quoted rate)
M/s Santosh Industrial Corporation
B & R CONSTRUCTION
DEYS ENTERPRISE
Rounaq Enterprise
S.S.ENTERPRISE
MODERN AGENCY
M/S SRINIVASA CONSTRUCTION
stage.html
html • 0.06 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .