lighting pole or post and hardware- tubular street light poles

lighting pole or post and hardware- tubular street light poles

LED Luminaire (For Road and Street Lights) Average Turn Over of Last 3 Years 15 Lakh (s) MSME Exemption For Years Of Experience And Turnover Yes Lighting Pole Or Post And Hardware- Tubular Street Light Poles ( 363 ) Technical Specifications * As per GeM Category Specification Specification Specification Name Values Allowed Values GENERIC Tubular steel poles shall be conforming to IS 2713/80(Part-1& 2) with amdt No-1 latest Yes * Designation of Tubular steel poles as per table 2 of IS 2713/80 Part-2 with amdt No 1 410SP-50 * Length of Tubular steel poles (Metre) 11 7

7.5

8

8.5

9

9.5

10

11 Coating on the tubular steel poles Bitumen coated as per clause 13.1 of IS:2713 part 1/1980 Galvanised min. Mass of Zinc coating 360 Gms. sq. Mtr.

Bitumen coated as per clause 13.1 of IS:2713 part 1/8 1/1980 BIS Marked Yes Yes

No If Yes

Declare BIS License Number

If No Write Not Applicable CM/L-8700045915 * CONSTRUCTIONAL Type of steel poles Swaged (SP) * Finials

Base plates and taper plug shall be as per clause 15 of IS 2713(Part-1)/1980 YES * Grade of steel tube

as per IS:1161/1998 YST 240 * CERTIFICATIONS Availability of Type Test Reports of the product from Central Govt/NABL/ILAC accredited Lab showing compliance to the specification YES * Test Reports No. CIL/160715010 * Test Reports Date 25.07.2016 * Name of the Labs CIMEC INFRALABS PVT.LTD * Test report and approvals to be furnished to the buyer on demand. YES * * Bold specifications are the golden parameters. Consignees and Quantity S.No. Consignee Address Quantity Delivery Days 1 Dinesh Babu K 335512

1030 IESPL Opposite Mahila Police Line Hanumangarh Jn Phone No 9468690026 363 30 LED Luminaire (For Road And Street Lights) ( 66 ) Technical Specifications * As per GeM Category Specification Specification Specification Name Values Allowed Values STANDARDS LED Luminaire conformity to IS:10322/Part 5/Section 3/2012 latest and IS: Yes * 2/8 16107 (Part 2/Sec 1):2012 latest Photo biological safety of LEDs used shall be as per IS:16108/2012 (exempt group) Yes * Types of LED Luminaire as per the IS: 16107(Part-2 Sec.-1)/2012 Type B * Types of LED Modules as per the IS:IS: 16103(Part-2)/2012 Type 3 * LED Rating (in Watts)/System Wattage/Rated Power 60W 60W Luminaire System Efficacy (Lumen/watt) >/= 100 Lm/Watt * Ingress Protection (IP Rating) as per IS:10322 (Part 1):1982 latest IP66 * Warranty for free replacement (in years) 2 2 ELECTRICAL EFFICIENCY Input operating Voltage range and frequency 140 to 270 V olts AC at 50 Hz+/-2 with auto cutt off at below 120V * Automatic Higher Cut off voltage above 300 volt Yes * Rated voltage 230 V AC 50 Hz * AC Power Factor at full load ≥ 0.95 * Driver Efficiency (in %age) Upto 100W: ≥85%

Above 100W: >/=90% Yes * Total Harmonics Distortion ≤ 10 * "The total circuit power shall not be more than 110 percent of the value declared by the manufacturer (as per Cl. 8 of IS:16104:2012 lates)" Yes * OPTICAL LED chip Efficacy ≥130 Lm/Watt * Colour temperature 6000+/-500K * 3/8 Working life for LED (Minimum 50

000 burning hours as per LM-80 and LM 21 reports) Yes * Colour Rendering Index(CRI) ≥70 * LED Beam Angle ≥120 * Optic lense materal (UV stabilised) Poly carbonate lense * THERMAL MANAGEMENT Heat sink should be die- cast aluminium along with sufficient heat sink fins to dissipate heat effectively Yes * Junctiojn/Soldering point temperature shall not exceed 85 deg.c as per LM 80 report Yes * Capacitor shall be rated for a temperature of 105 deg. celsius or better Yes * Operating temperature range -10 deg C to +50 deg C -20 deg. C to +50 deg. C

10 deg C to +50 deg C

10 deg C to +55 deg C Operating Humidity Range 10 % to 95% RH * PROTECTION Short circuit Protection Yes * Over load protecton Yes * Over Voltage protection Yes * Reverse polarity Yes * High voltage test (1.5 KV for one minute between supply terminals and body of the unit) Yes * Insulation resistance between earth and current carrying part >100 M Ohm * The luminaire shall be protected against surges and transients ( Internal) >/=4KV * The luminaire shall be protected against surges and transients of >/=10KV (External) No * 4/8 CONSTRUCTIONAL The Luminaires casing/housing (single piece housing) shall be pressure die casted aluminium alloy with higher thermal conductivity Yes * The luminaire body must be corrosion resistant powder coated Yes * All fastners must be of stainless steel Yes * Protection of the entire housing (both LED section and driver section) as per IS:10322 (Part 1):1982 latest IP66 * Extruded silicon loop gasket shall be provided in the lantern body to ensure a weather proof seal between the UV Glass cover and the metal housing to exclude the entry of the dust

water

insects etc.

Yes * Luminaries light transparency should be of Toughened glass Yes * Toughned transparent glass cover thickness >/=4 mm * Toughned Glass shall not get discoloured shall not suffer degration due to heat and ageing within warranty period Yes * Number of electronic control gear (power supplies) 1 No. 1 No.

2 Nos.

3 Nos.

4 Nos. Light Source SMD LED Chip as per LM 80/IS16106 * Driver components shall be industrial grade or above Yes * PCB shall be FR4 grade minimum 0.8 to 1.0 mm thick or more Yes * 5/8 The Luminaires works on single phase three wires system (Phase

Neutral and Earth) Yes * Suitable connector shall be provided for LED connection between driver output and LED Yes * Length of ISI marked three core wire (shall be provided along with supply of material) 50 cm 50 cm

100 cm MARKING "Manufactures Name and and brand on the aluminium die cast body " Engraved/Embossed * Manufacturer’s name

model number

serial number Yes * Date of manufacture (month-year)

and lot number as identification mark inside each unit and the outside of each packaging box Yes * The operation characteristics voltage and power be marked inside of each LED luminaire unit Yes * Diameter of pole Luminiare suitable for: (upto 45W Pole OD: shall be 40mm)

(>45W Yes * REPORTS AND CERTIFICATIONS LED Make OSRAM/NICHIA/CREE SAMSUNG/SEOUL LUMILEDS/PHILIPS SYSKA/LUMENMAX EVERLIGHT/EDISON BRIDGELUX NATIONSTAR/REFOND * System must have EMI/EMC compliance as applicable (Test reports shall be furnish to the buyer/consignee on demand) Yes * LM 79 (Photometry) (Ref.IS:16106:2012) Yes * 6/8 report from Central Government Lab NABL/ILAC accrediated lab. Reports shall be furnish to the buyer consignee on demand (LM-79 report shall have total lumen output

power

PF

Current in Amps

CRI & CCT etc.

) LM 80 & TM 21 (Ref. IS:16105:2012) Report and Photo biological report for LED report from Central Government Lab NABL/ILAC accrediated lab. Reports shall be furnish to the buyer consignee on demand (LM-80 report shall have the Pohoto Biological report of the LED Chip being used in the luminaire) Yes * Availability of test Report from Central Government Lab NABL/ILAC accrediated lab to Indian Standrad IS:10322/part 5/sec-3/2012 and IS 16107 (Part 2/Sec 1) : 2012 Yes * Seller shall furnish the Type test reports to the buyer/consignee on demand Yes * DC or AC supplied electronic control gear for LED Module shall comlpy as per IS:15885 (Part 2/Sec.13) Yes * LED Luminaire for road and street lighting shall comply with Complusory Registration(CRS) of BIS for safety as per IS 10322 (Part 5/Section 3): 2012 as applicable on date Yes * * Bold specifications are the golden parameters. 7/8 Consignees and Quantity S.No. Consignee Address Quantity Delivery Days 1 Dinesh Babu K 335512

1030 IESPL Opposite Mahila Police Line Hanumangarh Jn Phone No 9468690026 66 30