GE(S)/M-56/2022-23

Amount

Taking down existing cement plaster at any height on brick walls or stone walls of any description etc. including raking out joints, hacking for key, scrubbing down with water etc, complete all as specified and directed.

M&L for 10mm thick rendering on faces of brick work or concrete surfaces of walls in cement mortar 1:6, finished even and smooth without using extra cement complete all as specified and directed.

M&L for 15mm thick rendering in two layers (5mm thick in CM 1:4 over 10mm thick in CM 1:6) on brick work and concrete surfaces of wall, finished the surface even and smooth without using extra cement, mixing and including WPC @ 200ml/bag of cement complete all as specified and directed.

M&L for 10mm thick rendering or plastering work in CM 1:3 on fascia or edging of chajjas, ceiling and roof projections etc. including taking out peeled off existing plaster / concrete including roughening old concrete surface and making the line in true shape and finishing the surface without using extra cement, complete all as specified and directed.

M&L for preparation of newly plastered surface of wall and making the surfaces smooth by applying 2mm thick wall care putty and applying two coats of oil emulsion distemper, complete all as specified and directed.

M&L for preparation of newly plastered surface of wall and making the surfaces smooth by applying two coats of acrylic emulsion exterior paint, complete all as specified and directed.

M&L for preparation of old plastered surface of wall and applying one coat of acrylic emulsion exterior paint, complete all as specified and directed.

M&L for complete removal of existing treatment and applying 2mm thick wall care putty for making the surfaces smooth and applying two coats of oil emulsion distemper, complete all as specified and directed.

M&L for preparation of old surfaces of ceiling and applying one coat of white wash, complete all as specified and directed.

M&L for preparation of old steel surfaces over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floor and paving n exc 15cm thickness (below or above ground level), complete all as specified and directed.

M&L for vitrified ceramic light shade tiles 10mm thick polished, of size 1200x600mm as in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tile over and including 15mm thick screed bed or bedding layers in CM 1:6 for laying floor finishes, including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing rubbish off the premises complete all as specified and directed.

M&L for vitrified ceramic light shade tiles 8.5mm thick (Square or rectangular) polished, area of each tile exceeding 0.36 sqm in skirting/dado/riser of steps etc set & jointed in neat cement slurry and pointed in coloured cement to match the shade of tile over and including 10mm thick rendering in CM 1:4 for laying floor finishes, including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing rubbish off the premises complete all as specified and directed.

M&L for non skid ceramic coloured tiles 7 to 8mm thick, area of each tile exc 0.11 Sqm but not exc 0.18 Sqm as in floors etc, set and jointed (joint free) in neat cement slurry and pointed in coloured cement to match the shade of tile over and including 15mm thick screed bed or bedding layers in CM 1:6 for laying floor finishes, including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing rubbish off the premises complete all as specified and directed.

M&L for glazed ceramic coloured tiles of size 450mm x 300mm x 7mm thick on vertical surfaces, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile over and including rendering 10mm thick in CM 1:4 and finished rough to receive tiles including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing rubbish off the premises complete all as specified and directed.

M&L for 75mm thick PCC 1:4:8 type D-2 (using 40 mm graded crushed stone aggregate) as in sub base flooring complete all as specified and directed.

M&L for 25mm thick PCC 1:2:4 type B-1 (using 20 mm graded crushed stone aggregate) as in sub base flooring complete all as specified and directed.

M&L for machine cut granite stone 18 to 20mm thick on wall clading,steps,jambs,pillars,window cills cooking over and including 15mm thick plateform screed bed in CM 1:4, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing as in floors / cills etc, and moulding at edges (if required) including cutting holes 25mm dia for inserting gas pipe through the slab complete all as specified and directed.

M&L for 75mm thick cement concrete 1:3:6, type C-1 (using 20mm graded crushed stone aggregate) as in plinth protection and paving, laid in slope, finished even and fair including making joints at every 2.5 mtr and at corner filled with bitumen 85/25 and sand in ratio 1:2 by weight, complete all as specified and directed.

S&F "as in repair" 110mm bore PVC (SWR) laid in trenches or in floors complete all as specified and directed.

S&F "as in repair" 75mm bore PVC (SWR) laid in trenches or in floors complete all as specified and directed.

S&F in reapirs PVC (SWR) floor trap 75 mm with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed.

M&L 100 mm dia PVC (SWR) Bends with ovel access door and jointed with neat cement paste complete all as specified and directed.

M&L 75 mm dia PVC (SWR) Bends with ovel access door and jointed with neat cement paste complete all as specified and directed.

M&L 75 mm dia PVC (SWR) cowls complete all as specified and directed.

Taking down chowkhats or frames not exc 1.5 Sqm each with shutter (without taking off shutters from the frame), complete all as specified and directed.

Taking down chowkhats or frames exc 1.5 Sqm but not exc 4.0 Sqm each (without taking off shutters from the frame), complete all as specified and directed.

S&F factory made single extruded WPC (Wood Polymer Composite) solid door/window/Ceosetory windows & other frames/Chowkhat of size 50 x 125 mm comprising of virgin PVC polymer of K value 50-60 (Suspension Grade), calcium carbonate and natural fibres (wood powder/rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750kg/cum, screw withdrawal strength of 2200 N (face) & 1100 N (edge), minimum compressive strength of 58 N/mm2, modulas of elasticity 900 N/mm2 and resistance to spread of flame of class A category with property of being termite/borer proof, water/moister proof and fire retardant and fixed in position with MS hold fast /lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-charge.Note : for WPC solid door/window frames, minus 5mm tolerance in dimension i.e.depth and width of profile shall be acceptable . Variation in profile dimensions of plus side shall be acceptable but no extra payment on this account shall be made, complete all as specified and directed.

Supply and fixing to existing door frames 30 mm thick Glass Fibre Reinforced Plastic (FRP) panelled door shutter of required colour and approved brand and manufacture, made with fire - retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate for forming hollow rails and styles, with wooden frame and suitable blocks of seasoned wood inside at required places for fixing of fittings, cast monolithically with 5 mm thick FRP laminate for panels conforming to IS: 14856, including fixing to frames, complete as specified by the manufacturer and as per directions of Engineer- in-charge. complete all as specified and directed.

S&F pre-laminated lead free factory made 18mm (+ 0.7mm) thick 100% solid WPC (wood polymer composite) sheet having high natural fibre content 25 to 30% wood colour sheets having density not less than 600Kg/cbm and should be 100% termite/water proof, fire retardant, Eco friendly, finish at all edges for making edges lipping/bending, manufactured by single layer extrusion process with excellent screw holding capacity and shore D hardness complete all as specified and directed.

S&F 250mm long brass sliding door bolt with sand or dia cast brass hasp and staple (bolt type) and fixing bolt with rolled or drawn brass bolts and fixed complete, all as specified and directed.

S&F 200mm long brass barrel tower bolt with cast or sheet barrel and rolled or dia-cast fixed complete all as specified and directed.

S&F 125mm long brass handle, cast type, polished bright complete all as specified and directed.

S&F factory made 5mm thick PVC sheet one side prelam sheet for kitchen cabinet/cubboard of density 600 kg/Cbm bent 90º, complete all as specified and directed.

M&L for 0.8 mm thick PVC edge binding tape around the 18 to 20 mm thick PVC shutter edge colour as directed, complete all as specified and directed.

S&F continuous (piano) hinges, mild steel, bright finish or electro galvanised 40mm width of flaps (when open), complete all as specified and directed.

S&F 40mm dia polished hardwood knobs fixed with screws complete all as specified and directed.

S&F ball catcher with proper magnetic effect fixed with shutter, complete all as specified and directed.

S&F stainless steel plain basket of size 17'' x 20'' x 6'', complete all as specified and directed.

S&F stainless steel cutlery basket of size 17'' x 20'' x 6'' , complete all as specified and directed.

S&F stainless steel cup & soucer basket of size 17" x 20" x 4" complete all as specified and directed.

S&F stainless steel plate basket of size 17'' x 20'' x 6'' complete all as specified and directed.

S&F 20'' long telephonic slider to facilitate drawer slide of steel ball bearing fixed with SS screws, complete all as specified and directed.

S&F in repair 20mm bore stainless steel wood finish single curtain rod (wall thickness not less than 1mm) including fancy type brackets, funnels, knobs etc, complete all as specified and directed.

M&L for mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

M&L for Reinforced cement concrete type B1 1:2:4 nominal mix (using 20mm graded aggregates) in slabs supported on walls beams, columns etc including demolition of old reinforced concrete complete all as specified and directed.

Use and waste of formwork to soffits of concrete fair finished surfaces of suspended slabs such as roof slab,floor slabs , landings and similar works not exc 200 mm thick complete all as specified and directed.

M&L in repair for 15mm bore water tubes 'medium grade' galvanised with all fitting and fixed complete to walls and ceilings or laid in floors, including taking up or down steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and directed.

M&L in repair for 20mm bore water tubes 'medium grade' galvanised with all fitting and fixed complete to walls and ceilings or laid in floors, including taking up or down steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and directed.

S&F "as in repair" floor mounting single piece Vitreous china wash down water closet pan, light colour, complete including fixing to trap, along with PP soft close seat cover, hinges and accessories complete all as specified and directed.

S&F "as in repair" ovel type counter top Vitreous china wash hand basin, white, size 550mm x 400mm including 32mm bore CP waste coupling and 32mm dia flexible waste pipe including fixing of tap, complete all as specified and directed.

S&F "as in repair" double bowl kitchen sink, made of stainless steel 1mm thick, kitchen or laboratory with plugs, washers including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, of size 45"x20"x10" including CP waste coupling and 32mm dia waste pipe including making disturbed surface to match with existing surfaces, complete all as specified and directed.

S&F in replacement 15mm bore chromium plated, fancy type angular stop cock, cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions, complete all as specified and directed.

S&F "as in repair" 15mm bore bib tap with flange, fancy type, chromium plated, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed, complete all as specified and directed.

S&F 15mm bore chromium plated brass central hole single lever WHB mixture, for mixing hot and cold water with 450mm long braided house 20 cartriage size, screwed down, high pressure, screwed for iron pipe, complete all as specified and directed.

S&F "as in repair" high grade of stainless steel folding towel rack for bathroom of size 50.2cmx36.6cmx5.8cm with 4 double cross towel hook and swivel towel bar complete all as specified and directed.

S&F in replacement corner glass shelf assembly, quarter round with CP brass bracket, complete all as specified and directed.

S&F in replacement health foucet hand shower 8mm dia, with 1mtr long flexible pipe, wall hook, complete all as specified and directed.

S&F in replacement PVC connections 15mm size with PTMT nuts of length 450mm, complete all as specified and directed.

S&F "as in repair" CP soap nich fixed to walls with chromium plated brass screws complete all as specified and directed.

S&F 20mm bore gun metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

S&F 15mm bore gun metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

S&F Rotational moulded polyethlene water storage tank of capacity 1000 Litres, three layers (cylindrical vertical with closed top), hoisted and fixed in position including 20mm dia PVC ball valve, high pressure with polythene float complete all as specified in SSR Part-1, including dismantling of existing PVC water tank of any capacity complete all as specified and directed.

S&F 200mm dia CP towel ring fixed with SS screws and rowel plug complete all as specified and directed.

S&F ,Vitreous China Urinal, full stall type, coloured including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement, fixing of automatic flushing cistern with brackets, flush pipe, grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe) fixed incl supply and fixing of CP coupling, waste pipe and all necessary fittings, complete all as specified and directed.

S&F for 5mm thick coloured/printed solid PVC wall panelling/lining fixing on brick masonary wall inclusive 5mm thick PVC sheet and 35mm wide vertical PVC beading fixed with machine screw with horizontal spacing of 300mm c/c at site including demolition of existing lining of any description complete all as specified and dire

S&F 3mm thick PVC sheet fillet of width 35mm for wall paneling fixing on to wall making PVC frame as per specifications and drawings.

M &L for Fly ash brick work with straight or curved on plan exceeding 6 meter radius , built in cement mortar (1:6) including demolition of Brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles, including removal of deberies out of MoD land complete all as specified and directed.

Supply & fixing sensor type chromium plated brass faucet (battery operated) for wash hand basin 15mm bore, complete all as specified and directed.

Supply & fixing shower panel of size 1600 x 200 mm comprises of inbuilt ABS top shower with 60 nozzles, 2 movable ABS body massage jets, Hand shower with flexible hose, thermostatic mixer with diverter, 40cm SS braided hose, cascade shower complete incl connetion to 15 mm bore GI tubing complete all as specified and directed.

M&L 12mm thick seamless calcium silicate ceiling made out of 1800 x 1200mm , size board of siliceous and calcareous materials reinforced with cellolose fibre fixed to the ceiling section with 25mm long self drilling and tapping screws having philips head with under head cutter at 200 mm centre to centre, including finishing the joints of face boards with specially formulated jointing compound and 48 mm wide fibre tape to provide seamless finish incl GI frame work of grid size 605 x 605mm for seamless ceiling comprising of GI perimeter channel 0.55mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450mm centre to centre/ intermidiate channel 0.9 mm thick having two equal flanges of 15mm each and web of 45 mm suspendedfrom soffits at approx 900 mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (n.exc 1.2 m length) of 0.5mm thickness having kurled web of 50 mm anf flange of 26 mm each with lips of 10.5 mm fixed to the intermidiate channel with connecting clips accross the intermidiate channel at 457 mm centre to centre and Hangers 6 nn dia. G.I. (upto 1200 mm length) adujusting level fixed to roof slabs by means of ceiling cleats made out of G.I. flate 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia .40mm long complete, all as specified and directed.

Supply and laying UPVC sewage UDS (under drainage system) pipes 160mm bore single socket, wall thickness not less than 4.5mm type SN-4(IS-15328) type 'A' having nominal ring stiffness should be 2KN/Sqm with one coller per length of pipe with all fittings including taking out old pipes (salt glazed ware, AC or reinforced concrete) set in any mortar of any description/ type complete all as specified and directed.

M&L for concrete bed to drain pipes including packing under and haunching against the sides of pipe after they are laid and tested in cement concrete 1:4:8, type D-2 (using 40mm graded crushed stone aggregates) for 160mm bore pipe, complete all as specified and directed.

Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 (using 20mm graded crushed stone aggregates), smooth finished and reforming benching as required of 150mm bore pipe, including making good of manhole surface to match existing surface complete all as specified and directed.

S&F Rolled sections Fe-290 (Gde E-165) as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates, complete all as specified and directed.

M&L for preparation of new steel surfaces over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide complete all as specified and directed.

M&L for preparation of new steel surfaces n.exc 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide complete all as specified and directed.

M&L for welding in repairs n. exc 2.5cm in length and thickness of metal to be weld exc 6mm and n.exc 9mm complete all as specified and directed.

M&L for cement concrete in foundation, filling and mass concrete 1:4:8 type D-2 (using 40 mm graded crushed stone aggregate) as in sub base of floors, including demolition of old concretein ground floor & pavings complete all as specified and directed.

M&L for coloured machine pressed precast rubber moulded concrete interlocking (Red/yellow) paver block of any shape and size with 6-8mm white cement layer mixed with pigment and coated with epoxy coating having high glossy finish confirming to IS 15658-2006 of 60mm thickness, M-35 Grade, laid dry over and including 50 mm thick screened river washed sand cushion, and dismantling existing interlocking paver block of any shape and size removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L for Providing, cement concrete type B1, 1:2:4 (using 20mm graded aggregate) in roof kerbs or mud stops, rounded or chamfered on edges , in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs not provided for in Item 04028, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed, complete all as specified and directed.

M&L for 40mm thick PCC 1:2:4 type B-1 (using 20 mm graded crushed stone aggregate) as in sub base flooring complete all as specified and directed.

Taking down carefully aluminium / copper point wiring (light / fan / socket or power) complete with sunken boxes accessories etc., and making good disturbed surfaces of walls, floors to match with existing specifications and keeping aside serviceable items for reuse within the same bldg and removing UNSV items from site, complete all as specified and directed.

M&L for point wiring for one light point / fan point / bell point controlled by one switch with 1.5 Sqmm PVC insulated unsheathed copper conductor single core multistranded FRLS cable and 1.5 Sqmm PVC insulated unsheathed copper conductor single core multistranded FRLS (green colour) cable as earth lead drawn in and including connected non metallic rigid PVC conduit of 20mm dia & wall thickness 1.5mm and CI/MS terminal box of required size including inner and outer modular frame plate for mounting of modular switches/bell/fan regulators including cutting chases to walls and making good the disturbed surfaces to match with the existing specifications, complete all as specified and directed.

All as per srl item No. 87.00 here-in-before but for one 5 pin two module socket outlet 5/6 Amps on same board,complete all as specified and directed.

All as per srl item No. 87.00 here-in-before but with 2.5 sqmm FRLS PVC insulated cable for 3 pin 5/6 amp two module multipurpose outlet 5/6 Amps including 2.5 sqmm PVC insulated FRLS copper wire for earth continuity on independent board,complete all as specified and directed.

All as per srl item No. 87.00 here-in-before but with 4 sqmm FRLS PVC insulated cable for 3 pin 15/16 amp two module multipurpose outlet 5/6 Amps including 4 sqmm PVC insulated FRLS copper wire for earth continuity on independent board,complete all as specified and directed.

All as per srl item No. 87.00 here-in-before but with 4 sqmm FRLS cable PVC insulated cable copper wire for metal plug top for AC & geyser outlet including 4 sqmm FRLS PVC insulated copper wire for earth continuity on independent board complete all as specified and directed .

S&F modular switch piano flush button, single module, one way, 5/6 Amps, 240 Volts AC with polycarbonate body, complete all as specified and directed.

S&F modular switch piano flush button,one module, single pole, one way, 15/16 Amps, 240 Volts AC with polycarbonate body, complete all as specified and directed.

S&F modular socket outlet, 6 Pin, 5/6 and 15/16 Amps, 2 module, multipurpose, 2 in 1, flush type, 240 Volts AC with polycarbonate body, complete all as specified and directed.

S&F modular socket outlet, 5 Pin, 5/6 Amps, 2 module, flush type, 240 Volts AC with polycarbonate body, complete all as specified and directed.

S&Fmodular Bell push switch piano flush button, single pole, one way, 5 Amps, 230 Volts AC with polycarbonate body, complete all as specified and directed.

S&F modular fan regulator electronic switch type, 2 module step type hum free with polycarbonate body, suitable to control speed of fan from 0 to 100% in 5 to 8 steps control and connecting electrically, complete all as specified and directed.

S&F bell electric, heavy duty, Ding Dong type, 230 Volts AC, single pole, complete all as specified and directed.

S&F lamp holder PVC/ polycarbonate type with back plate including LED lamp 9/10 Watt for batten fitings complete all as specified and directed.

S&F ceiling rose, surface bakelite, 2 to 3 terminals, 230 Volts AC with polycarbonate body, complete all as specified and directed.

S&F sheet metal enclosure MCB distribution board, double door, single pole & neutral 240volts 08 way with IP-54 IK-09 protection complete with appropriate size bus bar and neutral link, fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces to match with existing specification, complete all as specified and directed.

S&F of 240 volts 10KA 'B' curve miniature circut breaker (MCB) of single poles, current carrying capacity 5 to 32 Amp in the MCB DB Complete with connection testing and commissioning, complete all as specified and directed.

S&F of 240 volts 10KA 'C' curve miniature circuit breaker (MCB) of single poles,neutral current carrying capacity 40 to 63 Amp in the MCB DB Complete with connection testing and commissioning, complete all as specified and directed.

M&L for submain wiring with two single core FRLS PVC insulated cable 6 sqmm (nominal dia) copper conductor (multistrand) and drawing in and including PVC concealed conduit pipe, ISI marked 20mm dia & 1.5mm thick including 6 sqmm multistranded copper conductor FRLS PVC green insulated unsheathed cable for earth continuity, including taking down existing submain wiring complete all as specified and directed. Note : Three runs of wire with conduit shall be measured as one unit.

S&F in replacement of surface mounted 1x20 Watt LED tube light fittings (4 feet long), prewired, decorative ultra slim square profile LED lighting fixture with extruded polycarbonate, enviornmental friendly, energy saving efficient ready to use pack 20 Watt LED 6500 K and making connection using 3 core, 0.50 sqmm PVC insulated and overall sheathed flexible copper conductor cable from ceiling rose/PVC connector to light fitting and testing etc, complete all as specified and directed.

S&F 15 Watt wall mounted decorative bracket light with injection moulded ABS body and unbreakable ribbed transluscent globe 15 Watt with prefixed lamp, complete all as specified and directed.

S&F "as in repair" of 1x10 Watt LED light fittings mirror type with high out put diffuser (2 feet long), prewired, decorative ultra slim square profile LED lighting fixture with extruded polycarbonate, enviornmental friendly, energy saving efficient ready to use pack 10 Watt LED 6500 K and making connection using 3 core, 0.50 sqmm PVC insulated and overall sheathed flexible copper conductor cable from ceiling rose/PVC connector to light fitting and testing etc, complete all as specified and directed.

S&F of surface mounted LED Bulk Head luminaires 9/10 watts with ABS body & polycarbonate diffuser available in CCT 6000K IP 54 complete all as specified and directed.

Supply, fixing in replacement of existing unsv recess/suspended slim LED panel light with powder coated rim 36 watts of size 2'x2' high efficency designer recessed mirror optic luminary with ceiling cut out size 36 watt including LED lamps complete including connecting electrically to ceiling rose using cord flexible 3 core PVC insulated over all sheathed with flexible copper conductor of size 0.75mm complete all as specified and directed.

Supply, fixing in replacement of existing unsv recess/suspended slim LED panel light with powder coated rim 18 watts of size 1'x1' high efficency designer recessed mirror optic luminary with ceiling cut out size 18 watt including LED lamps complete including connecting electrically to ceiling rose using cord flexible 3 core PVC insulated over all sheathed with flexible copper conductor of size 0.75mm complete all as specified and directed.

S&F in repalcement of LED building security light fitting 25 watts, IP 65, having pressure die cast aluminium alloy housing, prismatic polycarbonate cover, making connection with 3 core copper flexible cable of size 23/0.0076 including fixing of street light fitting galvanised iron bracket 0.90m long of suitable dia complete all as specified and directed.

Note for srl item No 105 to 111 1. Driver shall be potted anti-vibration types. 2. LM-79 and LM-80 test report with 1 Lakh burning hours LED life from NABL lab shall be provided. 3. CRI (Colour Rendering Index) of fixture shall be > 70. 4. CCT (Colour Co-related Temperature of fixture shall be 5700K + 300 K. 5. System Lumen Efficacy shall be > 100 Lm/W. 6. 10 KV separate Surge Protection shall be provided as a part of fitting. 7. 2 years guarantee shall be provided by contractor supported by OEM covering all parts of luminaire. 8. Lenses shall be Modular Type. 9. PCB used shall be MC PCB type. 10. The defect liability period of LED light shall be 05 years from the certified date of completion & the contractor shall replace/repair the defective fitting within 07 days after handing over to contractor for replacement/repair. 11. CA No. shall be written on each fitting before installation. 12. The name of manufacturer to be embossed on the fitting. 13. The fittings shall have arrangement so that maintenance required, if any can be carried out from Top cover.

S&F "in replacement" VTPN distribution board, double door, TPN 415 Volts 4 way degree of protection IP-65 DBs TPN suitable for MCCB as (for incoming MCCB & outgoing MCBs 415 Volts), including MCCB 415 Volts 63 Amp 16 Ka as incommer and 16 Nos MCB SP upto 63 Amp cap as outgoing complete with appropriate size copper bus bar for each phase, with 2 Neutral link, fixed flush in wall including chases wall for fixing DB and making good disturbed wall surfaces to match with existing specifications complete all as specified and directed.

M&L in replacement of earthing complete with galvanised GI earth plate electrode of size 600x600x6mm thick, burried directly in ground (earth pit not less than 2.25 Mtr deep below normal ground level) with top edge of earth plate not less than 1.5 Mtr below normal ground level, connected to galvanised earth lead wire 4mm dia by means bolt, nuts, check nuts and washer made of galvanised iron or steel including earth work in any type of soil, charcoal dust and salt layers 15cm thick all around the earth plate as shown in electrical plate No. 03 of SSR Part-I 2009 including 20mm bore GI watering pipe 'medium grade' with funel and wire mesh and 15mm bore GI protection pipe 'light grade' from earth pit to main board including PCC pit in cement concrete 1:2:4 type B-2 (using 40mm graded stone aggregate) and including angle iron frame of size 40x40x3mm with hold fast embeded in PCC, RCC pit cover with suitable handle and earth work and removal of surplus soil to a distance not exc 50 Mtr, complete all as specified and directed.

Supply and laying in trenches or fixed to wall/pole or passing through ducts or pipe, cable LT 1100 volts grade heavy duty, XLPE insulated, armoured heavy duty electric cable , with aluminium conductor of size 25 Sqmm x 4 core complete all as specified and directed. Note:- Excavation and earth work, sand cushioning, brick cover and protection pipe etc. shall be measured and paid for separately.

Excavating in trenches in any type of soil, n. exc. 1.5 m wide and n. exc. 1.5 m in depth, for foundation, etc. or for shafts, wells, cess pits, manholes, pier holes, etc n. exc. 10 sqm on plan and n.exc 1.5 m in depth and getting out complete all as specified and directed.

Returning, filling in (soil), including spreading, leveling, watering and well ramming in layers not exc. 25 cm complete all as specified and directed.

Removing excavated material (soil) n.exc. 50 m and depositing where directed at a level n. exc. 1.5 m above the starting point complete all as specified and directed.

M&L for dry clean fine river sand as in sand cushioning to underground cable 8cm below and 15cm above the cable including punning down of sand layer complete all as specified and directed. Note :- Punned thickness shall only be measured and paid.

M&L for brick protection with sub class 'B' old size brick well burnt laid flat for cable protection abutting each other laid dry with width equal to length of brick complete all as specified and directed.

Supply and fixing in replacement GI tubing light grade 50 mm bore cut to size and fixed along the pole for cable protection including clamp 02 Nos of size 25x4 mm, nut bolts , washers etc complete all as specified and directed.

M&L for single pole & neutral enclosure with a two pin and earth plug socket complete with one single pole MCB 20 Amps, 'C' curve 240 volts 10 KA complete all as specified and directed.

Dismantling and taking out burnt winding by cutting, cleaning slouts and re-winding of AC ceiling fan motor1200mm/1400mm of any make of fan with super enameled heat resistant copper winding wire of existing gauge & nos of turns including, sleeve work, varnishing with E class insulation, greasing, threading, connection with flexible wire 0.472 mm copper wire upto connector block and re-assembling and testing for 4 Hrs after repair complete all as specified and directed. (Repairs will be measured and paid for separately under respective items):- Notes :- (i) Fan shall be collected by the contractor from MES store yard at thier own arrangement. (ii) Motor shall be wound with machine only and repair of fan inside complex / office of GE (S) Mamun. (iii) Khaitan/RPG/KEI or equivallent make super enameled copper winding wire shall only be used. (iv) Rates are deems to be included cost of repair /servicing & replacement of minor spare part i.e. blade screws, capacitors clumps terminal connection , split pin spring washer etc.

Replacement of old unserviceable gun metal bush of ceiling fan complete all as specified and directed.

Replacement of old unserviceable capacitor AC 415 volts 2.5 mfd oil filed ISI marked complete all as specified and directed.

Replacement of old unserviceable ball bearing of suitable size as per existing make and size of ceiling fan complete all as specified and directed.

Servicing of ceiling fans of capacity 1200/1400mm including taking down from site , dismantling, cleaning, greasing/oiling of bush and bearings, replacement of set of split pins, cotter pins, blade screws, cup of both side and refixing to the existing site after servicing complete all as specified and directed. (Unserviceable parts if any will be measured and paid seperately). Note:- Contractor will deployed one elect & one helper for servicing of fans against srl item no 13 & 14 at site on all working day for the period of contract.

Replacement of old unserviceable fan blades as per existing shape, colour and design suitable for 1200mm sweep ceiling fan of any make complete all as specified and directed.

Servicing of exhuast fans of capacity up to 450 mm including taking down from site, dismantling, cleaning, greasing/oiling of bush and bearings, replacement of outer gasket and nut & Bolts incl cleaning of outer part & fixing wall and refixing to the existing site after servicing complete all as specified and directed. (Unserviceable parts if any shall be measured seperately).

Dismantling and Re-winding of exhaust fan/industrial wall mounting fan/pedstral fan motor 250-380mm sweep any make of fan with super enameled heat resistant copper winding wire 31 SWG to 34 SWG including cutting and getting out old brunt winding, sleeve work, varnishing with E class insulation greasing, threading, connections with twin core copper flexbile wire of size 23/0.0076mm of length not more than one mtr with each fan complete all as specified and directed. Notes:- (i) Exhaust Fan/pedestal fan shall be collected by the contractor from MES store yard at thier own arrangement. (ii) Motor shall be wound with machine only. (iii) Khaitan/RPG/KEI /RR or equivallent make super enameled copper winding wire shall only be used. (iv) Exhaust fan are deems to be included cost of repair /servicing & replacement of minor spare part i.e. body screws, capacitors clumps , clips etc.

Removing old paint by scraping with sand paper including washing and filling cavaties with filter and applying two coats of painting to ceiling fan 1200-1400mm sweep at workshop with heat resistant synthetic enamel paint by spray painting incl, writing MES No on the ceiling fans as directed. Note:- Paint qaulity and colour shall be get approved from GE.

Replacement of old unserviceable outer body of ceiling fan (bottom and uper cover plate incl all fitments such screws, gasket cover canopy of both side etc complete all as specified and directed.

Replacement of existing unserviceable canopy top & bottom of ceiling fan as per existing size & shape complete all as specified and directed.

Replacement of existing unserviceable shutter and lover of exhaust fan as per existing size & shape complete all as specified and directed.

Replacement of existing unserviceable MS fan blade of exhaust fan as per existing size & shape complete all as specified and directed.

M&L for lathe work incl re-alignment to rotor, stater sloter, cleaning welding , bracing and polishing etc and refixing after repair and testing complete all as specified and directed.

surjit enterprises

M/S S KUMAR & CO

dinesh enterprises

M/S NARESH KUMAR SHARMA

M/S BHOTO AND CO

Bidder Name

surjit enterprises

RD Engineers

M/S S KUMAR & CO

M/S BHOTO AND CO

dinesh enterprises

M/S NARESH KUMAR SHARMA