SPECIAL REPAIR OF CIVIL REST HOUSE AT BAWAL IN REWARI DISTT.

Amount

Removing door and windows (wood and steel) with chowkats by making recesses in walls when the walls is not to be dismantlled (a) doors [HSR 8.18 (a)]

(b) Window

(c) Clerestory Windows

Scraping (c) cement plaster [HSR 8.32 ©]

Dismantling white or coloured glazed tiles (to be carefully removed) [HSR 8.38]

Dismantling Concrete (d) cement concrete plain 1:2: 4 mi [HSR 8.6 (d)]

15 mm thick cement plaster 1:6 on the rough side of single or half brick wall [HSR 15.12]

Plastering on under side of Ceiling, 10 mm thick cement plaster 1:4 [HSR 15.52]

Cement concrete 1:2:4 gola 10cm X 10cm quadrant along junction of roof with parapet wall finished smooth, where specially specified. [HSR 13.64]

Cement concrete 1:1.5:3 with stone aggregate 20 mm nominal size for reinforced concrete work in Shelves excluding steel reinforcement, but including centring and shuttering, laid in position, complete in all respect. [HSR. 10.81+10.95 (a)].

Fe-500 E.Q.R. TMT Steel bars for bars R.C.C., works, where not included in the complete rate of R.C.C. including bending, binding and placing in position complete. Note:- Reinforcement shall be measured in length including hooks, if any separately for different diameters as actually used in work, excluding overlaps. From the length so measured, the weight of reinforcement shall be calculated in tones on the basis of IS-1732. Wastage , overlaps, couplings, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire or other methods for binding and placing shall not be measured and cost of these items shall be deemed to be included in the rates for reinforcements (NS).

Conglomerate floor 40 mm thick cement concrete topping 1:2:4 [HSR 14.9]

Tile terracing with one layer of tiles, 22.86 cm X 11.43 cm X 3.81 cm laid dry over a layer of mud mortar including grouting with cement sand mortar 1: 3 and top surface to be left clean. [HSR 13.14]

Cement pointing 1:2 flush on brick and tile walls. [HSR 15.62]

Flat brick on tile flooring laid in cement sand mortar 1:4 on 100 mm thick cement concrete 1:8:16 and 100 mm sand filling and cement pointed 1:2 on top. [HSR 14.22]

Providing and fixing 12 mm thick and 150 mm wide pelmet, with 25 mm diameter wooden curtain rod and brackets, including fixing with 25 mm X 3 mm M.S. flat 10 cm long and plugs (Teak),etc., complete (d) teak wood [HSR 17.59 (d)]

Providing and Fixing PVC Rainwater Pipe 6 kg. pressure of ISI mark in cement mortar during masonry work. Make:- Supreme, Finolex or Prince. [HSR 13.89]. (a) 100 mm dia PVC pipe 6 kg. pressure.

Providing and fixing HDPE WATER STORAGE TANKS of Sintex, Diplast, O.K. Supreme make with covers/lids marked with IS: 12701 on roof top of buildings including cost of hoisting and placing in position, making connections with inlet and outlet pipes, providing over flow & scour provisions with suitable plug on scour pipe including cost of nipples, washers, flanges for connections in tanks completein all respects to the satisfaction of Engineer-In-Charge. (Except civil work).(HSR 30.119) 500 Ltr capacity

Providing and fixing in position automatic brass ball valves in tanks. (b) With Plastic Ball (ii) 20 mm internal diameter. [HSR 30.110 (b) (ii)].

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE (to the approval of the Engineer-in-charge) EUROPEAN TYPE WATER CLOSET SUIT WITH NONCONCEALED ‘P’ OR ‘S’ TRAP with or without vent and all other necessary fittings as fully described in item no.30.3 above. (i) White [HSR 30.4 (i)]

EXTRA OVER item nos.30.3 to 30.6 FOR PROVIDING AND FIXING BEST INDIAN MAKE PLASTIC HYGENIC SEAT with lid complete instead of hollow black or white plastic seat and lid.(i) White plastic seat (Solid) [HSR 30.13 (i)]

Providing and fixing in position best Indian make lavatory suites (with full anti splash rim in vitreous chinaware and all other necessary fittings as fully described in item no 30.41 above (i) Size 510 mmx 400 mm with one no. tap (HSR 30.42 (i))

PROVIDING AND FIXING IN POSITION BEST QUALITY STAINLESS STELL SINKS WITH COMPLETE FITTINGS. AS FULLY DESCRIBED IN ITEM NO.30.51 ABOVE.a) 600mm X 450mm X 200mm [HSR 30.53 (a)]

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE SHOWER WITH 15 OR 20 I/D IN-LET (d) C.P. brass telephonic shower [HSR 30.66 (d)]

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE PAPER HOLDERS FIXED INTO wall with C.P. brass screws complete in all respects INCLUDING CUTTING AND MAKING GOOD THE WALLS ETC. (a) C.P. brass [HSR 30.67 (a)]

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE TOWEL RAILS FIXED in with raw slugs embedded in walls with C.P. brass screws. Complete in all respect INCLUDING CUTTING AND MAKING GOOD THE WALLS ETC. (a) 25 MM DIA C.P.BRASS ADJUSTABLE 750 mm long [HSR 30.68(a)]

PROVIDING AND FIXING IN POSITION GLASS SHELF FIXED IN WITH RAWAL PLUGS WITH C.P.BRASS SCREWS COMPLETE INCLUDING CUTTING AND MAKING GOODS THE WALLS ETC. (a) With C.P. brass brackets and guard rail (i) 600 mm X 125 mm [HSR 30.69(a) (i)]

Providing and fixing in position best Indian make Soap dish fixed into wall with C.P. brass screws and complete in all respects including cutting and making good the wells etc. (a) C.P.BRASS (i) Soap dish large [HSR 30.70 (a) (i)]

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE BEVELLED EDGE 5.5 MM THICK MIRROR mounted on ASBESTOS sheet GROUND FIXED IN POSITION BY MEANS OF 4 NOS. CHORMIUM PLATED BRASS SCREWS AND WASHERS over rubber washers and rawl plug embedded in the wall of chromium plated brass clamps with C.P. brass screws (as required by the Engineer-in-charge) COMPLETE INCLUDING CUTTING AND MAKING GOOD THE WALLS ETC. (a) Indiam Make (i) 600mm x 450 mm [HSR 30.71 (a) (i)]

Providing and fixing in position 15mm i/d C.P. brass bib cocks of best quality (as required by the engineer-in-charge). (a) Bib cock long body [HSR 30.75 (a)

(c) Bib cock

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE C.P. BRASS WALL MIXER 15 MM (a) With Telephonic Shower [HSR 30.81 (A)]

Supplying and fixing glass panes with moulding of commercial hard wood such as hollock, champ, chikrassy and chaplash etc.(Non coniferous timber other than teak, conforming to I.S. specification No.1003, kiln seasoned). (c) 4 mm thick (glazing area above 55 sq dm, but upto 84 sq dm of each pane) [HSR 17.36 (C)]

wire gauze fixed on chowkats with 25 mm thick kail wood cover moulding of full width. [HSR 17.27]

Factory manufactured paneled and glazed door shutters of commercial hard wood, such as hollock, champ, chikrassy and chaplash, etc., c(non –coniferous timber other than team, conforming to I.S specification no. 1003 kiln seasoned), with 100 mm wide vertical styles, 150 mm wide lock rail, 200 mm wide bottom rail and 100 mm wide other rails, with panelsof 12 mm thick, commercial veneered both side particle board or plywood of B.W.R. grade, hot pressed, including cost of iron hinges, screws, chock/cleats stops and nails etc. complete fixed in position(excluding the cost of any fittings, other than specified above but including labour for fixing the same position. [HSR 17.91 (b) (-) 17.18 - Note] (b) 35 mm thick

Factory manufactured Solid Flush Door Shutter, with block board core as per I.S. No. 1659-1969 bonded with water proof type phenol formaldehyde synthetic resin, hotpressed, conforming to I.S. 2202 part I and II, fixed in position, including iron hinges, screws, chocks/cleats and stops etc., (excluding the cost of any fittings other than specified above, but including labour for fixing the same in position. (Note:- reputed make such as Duro, Green, Kitply will be used as approved by Engineer-in- charge.). HSR 17.93 (a) - Note 1 under 17.18] Note:- The Agency to whom the work is alloted will have to produce original bill / voucher for all quantity in token of proof of purchase of material. (iii) 35 mm thick

Factory manufactured panelled door or glazed windows shutters of commercial hard wood such as Hollock & Champ only. (non coniferous timber other teak, confirming to I.S. pecificationNo. 1003, Kiln seasoned) with 100mm wide vertical styles, 150mm wide lock rail 200 mm wide bottom rail, and 100mm wide other rails, with panels of 15mm thick, tongued and grooved of commercial hard wood nd including cost of iron hinges, screw, chock/cleats, stops nails etc. complete in position (excluding the cost of any fittings, other than specified above, but including labour for fixing the same in position). (a) 30 mm thick. [HSR 17.90 (a) - Note 1 under 17.18].

Cost of aluminium fittings complete for doors and windows, such as tower bolts,handles, etc., and screws for these fittings (excluding sliding bolt) (a) for single leaf shutter [HSR 17.72 (a)]

Providing and fixing sliding bolt with nuts and screws,etc.,complete (b) aluminium (ii) size 250 mm X 16 mm [HSR 17.83 (b) (ii)]

Providing & fixing vitrified tiles of size 600 x 600mm of approved made in flooring laid in any pattern as specified over base of 20mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade to tiles. Note:- Tiles shall be of premium quality (first quality) of reputed manufacturer like NITCO, KAJARIA, & RAK. (HSR 14.89) (Note: double charged tiles shall be used)

Providing and fixing vitrified tiles of size 600x600mm of approved make in skirting / dado laid in any pattern as specified over base of 12mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade to tiles. Note:-Tile shall be of premium quality (first quality) of reputed manufacturer like NITCO, KAJARIA,RAK(Note: double charged tiles shall be used) (HSR 14.90)

Providing and fixing ceramic-tiles / anti-skid tiles of size 400x400mm or above size of approved make in floors laid in any pattern over base of 20 mm thick Cement Sand Mortar 1:3 and jointed with white cement slury mixed with pigment to match the shade of tiles. [HSR 14.91] Note:-Tile shall be of premium quality (first quality) of reputed manufacturer like NITCO, KAJARIA,RAK.

Providing and fixing 1st quality ceramic-glazed wall tiles confirming to I.S. 15622 (thickness to be specified by the manufacturer) of approved make in all colors, shades except burgundy, bottle green, black of any size as approved by Engineer -In-Charge in skirting, risers of steps and dados over 12mm thick bed of cement mortar 1:3 coarse and jointed with grey cement slurry, including pointing in white cement mixed with pigment of matching shades complete. (b) Size of ceramic Giazed tiles 300mm x 450mm.[HSR 14.92(b)]

Preparation of plastered or concrete surfaces for painting, including sand papering the surface, applying one coat of linseed oil and filling with approved quality filler, consisting of white lead, linseed oil, varnish and chalk mitti including finishing surface to the required finish, complete. [HSR 16.24]

Preparation of ply wood surface for painting including sand papering the surface and applying filling with approved quality filler consisting of white lead, linseed oil, varnish and chalk mitti including finishing the surface to required finish complete. [HSR 16.1+16.2]

Providing two coats of exterior acrylic emulsion paint. 2nd Quality (HSR 16.79 (a))

Painting two coats with plastic emulsion paint on walls on new work to give an even shade.[HSR 16.30]

Painting two coats with synthetic enamel paint in all shades on old wood-work or metallic or plastered or concrete surfaces to give an even shade including rubbing down old paint. [HSR 16.5]

Recovery items: The rates quoted against recovery items will not be included in the total amount rather is will be deducted while calculating financial statement of the agency. Material obtained from dismantling of existing brick work, bituminous layer and granular layer have been calculated taking assumption that 80% of theoretical material will be retrieved. The dismantled material can used in any of the item for the work after modification (bringing it to required specification) after approval from employer. In case it is not possible to use this material on the work, the agency can take away this material. This material can be taken away by the agency at the price quoted by the agency but minimum price to be quoted is limited to reserve price as fixed and mentioned as under:- Removing of door with Chowkats @ 1000 Each

Removing of window @ 1000 Each

Clerestory Windows @ 300 Each Note: - All quantities of the above materials have been worked out on the basis of theoretical quantities laid on this road. However, agency may visit site before quoting rates and assess the extent of retrieved material. There shall be no measurement after actual dismantling and if material after dismantling is found on lesser side, no claim of agency on this score will be entertained and full recovery on the basis of quoted rate and quantity exhibited in the BOQ shall be made. The reserve rates are minimum rates to be used as base for quoting purchase rate by the agency. No rates below the reserve price will be entertained and reserve price will be considered for all purposes in case the agency quotes lesser than reserve price. Note :- In case of any difference in the unit and nomenclature of any of the HSR items of Civil & P.H. work depicted in this DNIT and the given in HSR, the unit nomenclature given in HSR shall be applicable.

THE BASTI RAM CO OPRETIVE LABOUR AND CONSTRUCTION SOCIETY LIMITED