PROVN OF IRON GRILLS TO ALUMINIUM FRAMED GLASS DOORS AND WINDOWS AT 7 BRD, RENOVATION OF NTC BUILDING IN SPYDER COMLEX AT 7BRD AND PROVN OF QTY 10 TURBO VENTILATORS FOR BLDG NO P-81 AT AF STN TUGHLAKABAD UNDER GE (AF) TUGHLAKABAD

Amount

M&L for Cutting holes into or through brick walls built in cement mortar and making good in cement mortar (1:3) or cement concrete (1:2:4) type B-1 as required superficial area n exc 150 Sqcm complete all as specified and directed by Engr-in-charge.

S&F Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 5 cm and n exc 10 cm long dia of shank 5 to 10 mm as per required complete all as specified and directed by Engr-in-charge.

S&F Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, grills, square bars etc., complete, Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also welding fastening and fixing complete Fe-290(Gde E-165) complete all as specified and directed by Engr-in-charge.

S&F Framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290. Gde-E-165 complete all as specified and directed by Engr-in-charge.

S&F Collapsible steel gates, top hung, consisting for channel pickets, pivoted flat bars, top and bottom runners, brass handles etc., as specified, erected in position and securing runners with holdfasts and brackets, complete all as specified and directed by Engr-in-charge.

S&F Welded steel wire fabric exc 4 Kg/Sqm welded to steel section at any position complete all as specified and directed by Engr-in-charge. (1950+150)

M&L Preparing new steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide zinc chrome primer complete all as specified and directed by Engr-in-charge. (950+27)

S&F 100 mm butt hinges medium weight cold rolled complete all as specified and directed by Engr-in-charge.

S&F 300 mm mild steel sliding door bolts, clip type, stone enameled block with bright bolt not less than 12mm dia with and incl Hasp & Staple a minimum of 6 bolts and nuts, on staple plate complete all as specified and directed by Engr-in-charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) complete all as specified and directed by Engr-in-charge. (330+245)

S&F Vitrified Ceramic tiles 10 mm thick (square/rectangular) polished, area of each tiles not exceeding 0.36 Sqm, in floors set and jointed in neat cement slurry and pointed in white or coloured cement to match in floors over 15mm thick screed bed in CM (1:6) complete all as specified and directed by Engr-in-charge.

M&L for vitrified ceramic colour tiles light shade 7 mm thick (square /rectangular) polished area of each tiles vertical surface 350x 250x 7mm/ 450X 350X 7mm thick in dado/skirting etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match including 10mm thick back coat in (1:3) complete all as specified and directed by Engr-in-charge.

Taking down cement or cement lime plaster on brick or stone wall etc including racking out joints, hacking for key, scrubbing down with water complete all as specified and directed by Engr-in-charge. (280+300)

M&L for rendering 15mm thick in patches cm (1:6) on fair faces of brick work or concrete surfaces finished even & smooth without using extra cement complete all as specified and directed by Engr-in-charge. (160+150)

M&L for rendering 15mm thick in patches cm (1:4) on fair faces of brick work or concrete surfaces finished even & smooth without using extra cement complete all as specified and directed by Engr-in-charge. (120+100)

M&L for two coats of distemper oil emulsion over coat of primer and over 2mm thick wall care putty to newly plastered wall surfaces including preparation of surface complete all as specified and directed by Engr-in-charge.

M&L for preparing new surface of walls and applying two coats cement base on new surface complete all as specified and directed by Engr-in-charge. (120+100)

M&L for anodised aluminium frame (minimum 50 micron powder coating) for doors, windows, ventilators with one or more rebates including cleat for fixing etc. complete all as specified and directed by Engr-in-charge. (210+90)

S&F aluminium anodised powder coated of any colour (thickness or powder coating not less than 50micron) doors shutters aluminium section weighing 0.55 Kg/Sqm including necessary jointing cleats, glazing clips, rubber neoprene packing, handles two nos in each door, hinges, anodised aluminium snap beading, screws complete all as specified and directed by Engr-in-charge. (40+30)

S&F 12mm thick Prelaminated particle board, interior grade, prelaminated both side with decorative choice lamination fixed with screws to timber frame work complete all as specified and directed by Engr-in-charge.

S&F Anodised aluminium powder coated window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary jointing cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified and directed by Engr-in-charge. (30+15)

M&L for sheet glass ordinary quality 3.00 mm thick and glazing with oil putty in square n exc 0.50 Sqm in each panes fixed to steel or wooden window frames complete all as specified and directed by Engr-in-charge.

S&F Aluminum anodized Deko grill MG104(100mmx105mm) including necessry FUH channel joint cleats screws etc. complete all as specified and directed by Engr-in-charge. Make: Jindal

S&F Door closer hydraulically regulated, designation No 3, universal type, Aluminium (extruded section body) suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80kg and fixed complete all as specified and directed by Engr-in-charge. (14+8)

Refixing of chowkats or frame with shutter (without taking out shutter from the frame), exceeding 1.50 Sqm and n exc 4.00 Sqm each in same opening at site complete all as specified and directed by Engr-in-charge.

S&F in repairs double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box main body with stainless steel cover governing pivot made of brass other parts made of mild steel heavy duty and fixed complete all as specified and directed by Engr-in-charge.

S&F Stainless steel (SS-304) wind turbine ventilator of 24" throat dia size with capacity of 2700 cfm to be mounted on top of FRP base plate of size 5 1/2'x 3 1/2 x 2mm thick with venture dome, including necessary cutting of existing roof sheets ceiling with water tight arrangement etc. complete all as specified and as directed be Engr-in charge. Technical specification of fan - no MOC of fins 42/ss Thickness of fins 0.5mm M.O.C of top cover & mounting ring SS internal fittings (shaft base frame & Cutting roads) GI Revolation Mechanism Double jet sealed ball bearings or self lubricated nylon bush.

Supply, installation, commissioning of hi wall split units indoor/outdoor complete with cordless remote control Each unit and within built air ionizer and Plasma filter for better indoor air quality with minimum 5 star rating and EER 3.2 of capacity 1.5 Ton, complete all as specified and as directed be Engr-in charge. Note: Making hole in wall, insulation of copper tubes, stand for outdoor unit (wall mounted/roof top type) T&P required for installation & making good the disturbed surface is deemed to be included in quoted rates.

S&F Industrial socket sheet metal enclosure with socket plug top and MCB single pole and neutral Each with a two pin and earth plug and socket with one single pole MCB of 20 Amp complete all as specified and as directed be Engr-in charge. Note: Flushing of AC box in wall & making good the disturbed surface is deemed to be included in quoted rates.

S&F sub-main wiring with unsheathed multi-stranded FR Grade copper conductor cable 1100 volts grade drawn RM through in and including PVC rigid conduit medium grade of not less than 20mm dia with conduit accessories and concealed in wall/surface of ceiling for two runs of 4 Sqmm single core FLRS Grade and one run of 4 Sqmm PVC insulated copper conductor for earth continuity wire between main DB to Sub main DB/ AC plug points complete all as specified and as directed be Engr-in charge. Note: Two run of single core cable with one run of earth continuity conductor and PVC conduit and accessories will be measured as one length including cutting chasing in wall complete. Rates are deemed to be included for chases of conduit and sunking for boxes cutting and making holes in wall/floor for passing in or through conduit.

S&F Voltage stabilizer for automatic operation, single phase naturally air cooled indoor type & Each designed for input variation between 140 V to 280 V with output voltage stabilized at 230 V with accuracy of 2.5% and of capacity 4 KVA, complete all as specified and directed by Engineer-in-charge.

S&F three layer PVC anti-static Rubber mat for floor consists of a static dissipative layer on the top, conductive layer in the middle and a static dissipative layer on the bottom. The size of the mat is 10mx1mx2mmthick complete all as specified and directed by Engr-in-charge. Note: (i) The standard size of one roll 107 SFT with Installation. (ii) Lay on the Floor with copper strip. Copper strips should be 0.05mm thick and 18mm wide. Determine the length and number of pieces of copper strips according to the actual measurement. Meanwhile, ground one terminal of the copper strip. Make a grid of 2Mtr X 2Mtr on the entire ESD floor area. (iii) The Glue should be applied on the whole surface area and then the copper grid is to be fixed and on it the mat is laid (iv) Grounding of mat is done by the grounding wire, one end of which is connected with the grounding button on the copper strip & the other end with earth point. (v) Thermo welding is done to connect the joints in between the mats to maintain connectivity.

S&F two layer PVC anti-static Rubber mat consists of a static dissipative layer on the top, conductive layer in the middle and a static dissipative layer on the bottom. The size of the mat is 15mx2mx1.5mm thick complete all as specified and directed by Engr-in-charge. Note: (i) The standard size of one roll 323 SFT with Installation. (ii) Lay on the wooden surface floor with copper strip. Copper strips should be 0.05mm thick and 18mm wide. Determine the length and number of pieces of copper strips according to the actual measurement. Meanwhile, surface /ground one terminal of the copper strip. Make a grid of 2Mtr X 2Mtr on the entire ESD wooden floor area. (iii) The Glue should be applied on the whole surface area and then the copper grid is to be fixed and on it the mat is laid (iv) Grounding of mat is done by the grounding wire, one end of which is connected with the surface/grounding button on the copper strip & the other end with earth point. (v) Thermo welding is done to connect the joints in between the mats to maintain connectivity.

M&L for Rendering 5mm thick in cement mortar in (1:3) on ceiling even and smooth without using extra cement complete all as specified and directed by Engr-in-charge.

M&L for preparing new surfaces of walls and applying two coat of Oil bound distemper on new surface complete all as specified and directed by Engr-in-charge.

All as per item No 36 above but three coat white wash on ceiling complete all as specified and directed by Engr-in-charge.

Supply only integral water proofing compound complete all as specified and directed by Engr-in-charge.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) n.exc 1.5 Sqm each complete all as specified and directed by Engr-in-charge.

All as per item No 39 above but exc 1.5 Sqm but n.exc 4 Sqm each complete all as specified and directed by Engr-in-charge.

S&F 4mm thick sheet glass for window/ventilators ordinary quality and glazing with rubber beading in square exc 0.50 Sqm in each pane complete all as specified and directed by Engr-in-charge.

S&F for solid PVC door frame of Size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced complete all as specified and directed by Engr-in-charge.

S&F of factory made solid panel PVC door shutter 30 mm thick (Style) consisting of frame made out of MS tube for top and bottom rails MS frame shall be covered with heat moulded plain colour PVC 'C' channel having PVC sheet strips of 20mm width stuck inside with solvent cement for style and plain colour PVC sheet for top rail, bottom, lock rails on either side and as gap insert for top rail and bottom rail paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles and rails with suitable PVC sheet, beading, and joined together with solvent cement, supplying and fixing in the frame at site as per specification and drawing complete all as specified and directed by Engr-in-charge.

S&F for stainless steel butt hinges with stainless steel pins 100mm size complete all as specified and directed by Engr-in-charge.

S&F for aluminium anodised barrel tower bolts of extracted section of size 150mm length complete all as specified and directed by Engr-in-charge.

S&F for 150mm extruded aluminium alloy handles, fabricated type anodised complete all as specified and directed by Engr-in-charge.

Demolition of cement concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and directed by Engr-in-charge.

M&L for PCC (1:2:4) type B-2 (using 40mm graded agg) 75mm thick as in plinth protection complete all as specified and directed by Engr-in-charge.

M&L for Glazed ceramic coloured tiles in vertical surface 7.0 to 8.0mm thick 0.06sqm to 0.09 sqm set including 15mm thick screed bed in cement mortar (1:4) complete all as specified and directed by Engr-in-charge.

M&L for Non skid ceramic colour tile 7.00 to 8.00 mm thick (square/rectangular) area exc. 0.11 Sqm and n.exc 0.18 Sqm in floor including 15mm thick screed bed in cement mortar (1:4) complete all as specified and directed by Engr-in-charge.

M&L for light shade Vitrified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.36 Sqm but not exceeding 0.42 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, Laid on Floor, over and including 15mm thick screed bed in cement mortar (1:4) Laid and Jointed in Neat cement slurry and Pointed in White or Coloured Cement to match the shade of the Tiles complete all as specified and directed by Engr-in-charge.

All as per item no 51 but in skirting including 10mm thick back coat in CM (1:3) complete all as specified and directed by Engr-in-charge.

S&F in repair of 15mm dia pillar taps, cast copper alloy, with capstan heads, chromium plated screwed down high pressure, with or without lettered Hot or Cold with long screwed shanks and fly nuts, screwed for iron pipe and fixed complete all as specified and directed by Engr-in-charge.

S&F in repair 15mm bore stop valve cast copper alloy screwed high pressure with crutch or butterfly handle, screwed both end for iron pipe or for union complete all as specified and directed by Engr-in-charge.

S&F in repair WHB vitreous china (580x450mm) flat back including connector, waste pipe brackets complete all as specified and directed by Engr-in-charge.

S&F in repair of 15mm dia bib taps, cast copper alloy, with capstan heads, chromium plated complete all as specified and directed by Engr-in-charge.

S&F in repair 110 mm PVC (SWR) pipe single socketed in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed by Engr-in-charge.

S&F in re pair PVC (SWR) bends (TEE,Elbow & socket) any radius 110mm bore complete all as specified and directed by Engr-in-charge.

S&F in repair for 32 mm bore waste coupling of PTMT (half or full threated) (minimum weight 45 gms) complete all as specified and directed by Engr-in-charge.

Taking up or down steel tubing and connections 15mm bore pipe complete all as specified and directed by Engr-in-charge.

Taking up or down steel tubing and connections 20mm bore pipe complete all as specified and directed by Engr-in-charge.

S&F GI water tubing medium grade 20mm bore with all fittings and fixed to walls and ceiling or laid in floors complete all as specified and directed by Engr-in-charge.

S&F GI water tubing medium grade 15mm bore with all fittings and fixed to walls and ceiling or laid in floors complete all as specified and directed by Engr-in-charge.

S&F in repair 100 mm dia cast iron floor trap with grating including jointing to waste pipe in run lead fixed in concrete (1:2:4) type B-1 complete all as specified and directed by Engr-in-charge.

Demolition of brick / stone work built in cement mortar including all quoins, arches, pillars etc. excluding ash lar facing, dressed stonework and precast concrete articles complete all as specified and directed by Engr-in-charge.

M&L for brick work with sub class ‘B’ bricks, straight or curved on plan exceeding 6m mean radius built in cement mortar (1:6) complete all as specified and directed by Engr-in-charge.

S&F in repair wash down water closet EWC with soft close seat cover and twine flush fitting 710x370x745mm complete all as specified and directed by Engr-in-charge. Make : Cera,

S&F Vitreous china squatting pan, Orissa pattren of size 580x440mm whit with integral foot rest (excluding flushing cistern and flush pipe) fixed in repairs complete all as specified and directed by Engr-in-charge. Make :- Cera/Parryware

S&F CI "P" or "S" trap 100mm dia complete all as specified and directed by Engr-in-charge.

S&F in repair PVC valveless, syphonic action type, flushing cistern,10 litre capacity, low level white, with inlet, ball valve, float and handle including brackets with all fitting complete all as specified and directed by Engr-in-charge.

S&F in repair Flush pipe of polyethylene of low or high density or PVC.32 mm dia for low level flushing cistern complete all as specified and directed by Engr-in-charge.

S&F in repair PVC connections 15 mm size with PTMT nuts if length 600mm complete all as specified and directed by Engr-in-charge. Make :- Prayag/Symat

Dismantling of water tank exc 250 but not exc 500 complete all as specified and directed by Engr-in-charge.

Dismantling of water tank exc 500 but not exc 1000 complete all as specified and directed by Engr-in-charge.

S&F of rotational moulded polyethylene water storage tank (cylindrical vertical with closed top), three layered, hoisted and fixed with position of 500 ltrs capacity including tank nipples complete all as specified and directed by Engr-in-charge.

S&F of rotational moulded polyethylene water storage tank (cylenderical vertical with closed top), three layered, hoisted and fixed with position of 1000 ltrs capacity including tank nipples all fittings complete all as specified and directed by Engr-in-charge.

S&F of framed work such as grills gratings, etc with ends of bars shouldered and or riveted or forged into spikes, framed guard bars barred iron doors ladders framed balusters walk way railing framework of Fe-410-0 or Fe-310-0 complete all as specified and directed by Engr-in-charge.

ANAND ENTERPRISES

M/S S.K.Electricals