Providing of Galvalume sheet roofing and other repair works for Mechanical Cultivation Office workshop areas behind Directorate of Agriculture Krishi Bhavan Building Tonca Caranzalem Goa

Amount

Earthwork in excavation by mechanical means (hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sq.m on plan) including disposal of excavated earth lead upto 50 m and lift upto 1.5m disposed earth to be leveled and neatly dressed including providing barricading, danger lighting guarding as directed in :a)All kinds of soil

Supplying and filling in plinth under floors, trenches including watering ramming consolidating, dressing, complete.Moorum

Rubble packing with hard laterite stone under floors including watering ramming and consolidating etc. in pipeline trenches and other foundations complete.

Laterite masonry in neatly dressed stones of size as specified in cement mortar 1: 4 (1 cement : 4 coarse sand) in foundation and basement.

Laterite masonry in neatly dressed stones of size as specified in cement mortar 1: 4 (1 cement : 4 coarse sand) in foundation and basement.Extra for laterite masonry in all sizes in superstructure from floor I level upto floor V level.

Providing & laying cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 graded granitic or basaltic stone aggrt. 20 mm. nominal size) excluding cost of centering, shuttering and finishing in:a)All works upto plinth level

Providing and laying in position (1:11/2:3) Reinforced cement conrete excluding the cost of centering, shuttering, finishing and reinfrocement (1 cement: 1½ coarse sand:3 graded stone agg 20mm nominal size) a)all works upto plinth level

Centering & shuttering including Strutting, Propping & removal of forms for :i)Foundations, Footings, Bases for columns

Centering & shuttering including Strutting, Propping & removal of forms for :iii)Columns, Pillars ,piers,abutments, posts and strut, square, rectangular, polygon in plan. etc.

Centering & shuttering including Strutting, Propping & removal of forms for :Xiii)Suspended floors, roofs landings, shelves & their supports

Providing High yield strength steel reinforcement bar (HYSD)/TMT steel reinforcement bar from secondary producers (Confirming to IS 1786 of 1986) for RCC work including bending, binding & placing in position in all the floors along with the factory made precast concrete cover blocks of specified sizes whose compressive strength is not less than that of surrounding concrete in the structural member.

Providing woodwork in frames of doors, windows, clerestory windows trusses & other frames wrought framed and fixed in positon.First class matti wood

Providing and fixing aluminium butt hinges anodised transparent or dyed to required colour or shade with necessary screw etc. complete.125 75 x 4 mm

Providing & fixing ms. Sliding door bolts bright finished or and black enamelled with nuts and screws etc. complete300 x 16 mm

.Providing and fixing M.S. tower bolts (barrel type) with necessary screws etc. complete250 x 10 mm

Steel work welded (SAIL, TATA. VIZAG & using electrodes of Ador or ES4B or Deh Secheron make only)in built up sections trusses and framed work including cutting, hoisting, fixing in position and applying priming coat of red lead paint.a)in R.S.Joists

Steel work welded (SAIL, TATA. VIZAG & using electrodes of Ador or ES4B or Deh Secheron make only)in built up sections trusses and framed work including cutting, hoisting, fixing in position and applying priming coat of red lead paint.b)In tees, angles, flats and channels

Steel work in single sections available on site using electrodes of Ador or ES4B or Deh Secheron make only)including cutting hoisting fixing in position and applying a priming coat of red lead paint in R.S. joists,channels,angles,tees

Supplying and fixing rolling shutters of approved make, made of 80 x 1.25 mm M.S. laths interlocked together through their entire length and jointed together at the end by end locks mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete including the cost of providing and fixing necessary27.5cm long wire springs grade No.2 and M.S. top cover of 1.25mm thick for folling shutterstop cover and spring.

Providing and fixing M.S. fan clamp type 1or II of 16 mm dia M.S. bar bent to shape with hooke ends in R.C.C. slabs, beams during laying including painting the exposed portion of loop, all as per standard design complete.

Providing & fixing M.S. round holding down with nuts & Washer plates complete.

Providing and fixing anodized aluminium shutters in accordance with the specification annexed with Goa schedule of Rates (2004) Vol & II including all taxes, transportation, scaffolding and handling etc. complete as per direction of the Engineer-in- charge: Adjustable louvered windows.Figured glassExtra for powder coating with pure polyester powder of shade of required colour on the aluminium section

Kotah stone slab flooring over 20 mm (average) thick base laid over & jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing & complete with base of cement mortar 1:4 (1 cement : 4 coarse sand)20 mm thick.

Providing and laying crazy paving (as per design shown in the drawing or as directed by the engineer-in- charge) with approved quality shahabad tile 20 mm thickness (unpolished) of specified sizes laid on 20 mm thick (average) bed of cement mortar 1:5 (1 cement : 5 coarse sand) as directed completed.

Providing and fixing coloured ceramic tiles spartek or equivalent of 12" x 12" size and 6 mm thick in floors thread of steps and landing on 25 mm thick bed of cement mortar 1:3 and jointed with cement slurry complete.

Marble stone flooring with 18 mm thick marble stone (sample of marble shall be approved by Engineer-in-charge) over 20mm (average) thick base of cement Mortar 1:4 (1 cement:4 coarse ) using :white Makrana Marble.

Providing and fixing vitrified matt finished (600x600) and 10mm thick tiles in floor, treads of steps, landing on 25mm thick bed of cement mortar 1:3 and jointed with cement slurry complete.

Providing and fixing 1st quality ceramic glazed wall tiles (Johnson, Somany, Kajaria )conforming to IS:15622 (thickness to be specified by the manufacture of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-charge in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand ) and jointing with grey cement slurry @3.3kg per sq.m including pointing in white cement mixed with pigment of matching shade complete.Wall Ceramic Glazed Tiles : 300 x 450

Providing and and laying antiskid floor tiles 12 x 12 upto 16 x 16 in of Johnson, Somany, Kajaria (thickness to be specified by the manufacturer) of 1st quality conforming to IS:15622 of approved make in shades as specified laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand) including pointing the joints with white cement and matching pigment etc., complete

Providing and fixing 20mm thick wooden planks ceiling (frame work for base to be paid separately) with M.S. screwsIndian teak wood second class

Providing and fixing colour coated galvulium roofing sheets of 0.5mm thickness including all the accessories (TATA make) but excluding the cost of purlins, rafters, trusses, flashings etc. complete as per the directions of the Engineer in charge.

Add for providing & fixing Flashings -[Corners, Ridges, valleys, gable end & Trims] (Girth above 610mm) including all the accessories complete as per the directions of the Engineer in charge.

Providing and fixing Prince or equivalent make PVC SWR half round eaves gutter with bolts, nuts and flat iron brackets 40 x 3 mm size complete.c)250 mm nominal size

Extra for providing and fixing prince or equivalent make PVC SWR joint bracket with 2 clamps for socketed half round eaves gutters.c)250 mm nominal size

Extra for providing and fixing prince or equivalent make PVC SWR running outlet with 2 clamps for socketed half round eaves gutters.250 mm nominal size

Extra for providing and fixing prince or equivalent make PVC SWR short stop ends for socketed half round eaves gutters.c)250 mm nominal size

Providing & Fixing in position Double Skin roof with Zincalume/ Galvalume colour coated & bare profile sheet with subtle square fluting factory cut at all heights for roof, side & Gable cladding complete in all respect. TOP SHEET-The end rib shall be designed for anti-capillary action. The feed material should be manufactured out of nominal 0.45 mm Base Metal Thickness (BMT), Hi-strength steel with min. 550 MPa yield strength, metallic hot dip coated with Aluminium-Zinc alloy (55% Aluminium, 43.5% Zinc &1.5% Si) as per AS 1397 - Zincalume AZ150 (Min. 150 gms/sq.mt total on both sides) with quality paint coat as per AS/NZS 2728 type 3-4. The paint shall have a total coating thickness of nominal 35 μm, comprising of nominal 20 μm exterior SMP coat on top surface and nominal 5 μm reverse backer coat on back surface over nominal 5 μm primer coat on both surfaces of approved colour shade. Total Coated Thickness (TCT) should be 0.50mm. Total Painted Thickness (TPT) should be in addition to 0.50mm. The steel sheet shall be fastened with nominal 40 μm zinc coated or nominal 25 μm zinc-tin alloy coated, Hex head, self-drilling screw as per AS 3566-2002 Class 3 fasteners of approved make with EPDM washer as per the requirement considering the profile shape and design load. The fastener size shall be calculated as per the design or manufacturers recommendations. The profile sheet, fastener size etc. shall be approved by the Engineer. The sheeting should be with minimum 200mm lap & waterproof with Silicon sealant non-hardening neutral cure type shall be applied at all end laps, complete as directed Z-Sub Girt - roll formed section 50x50x50x1.50 TCT, 120GSM Galvanised, High Strength (345 MPa), approximate Wt. 1.85 kg/r.m. fixed with self tapping screws Glass Wool Insulation with FSK facing 50mm with 24 kg/m3 density in between 2 sheets. LINER SHEET-bare galvalume/zincalume roofing sheet of same profile as top sheet. The feed material is of manufactured out of nominal 0.45 mm Base Metal Thickness (BMT) (0.47 mm TCT), Hi-strength steel with min. 550 MPa yield strength, metallic hot dip coated with Aluminium-Zinc alloy (55% Aluminium, 45% Zinc) as per AS 1397 - Zincalume AZ150 (Min. 150 gms/sq.mt total on both sides), passivated & resin coated. The feed material should have coil manufacturer’s product details marked at regular interval for confirming genuinity of the material. complete as per the directions of the engineer. The steel manufacturer's test certificate for the chemical & mechanical properties of steel must be submitted for approval prior to installation.

18mm cement plaster in two coats under layer 12mm thick cement plaster 1:5 ( 1 cement : 5 coarse sand) and top layer 6mm thick with cement plaster 1: 3 (1 cement : 3 coarse sand) finished with sponge.

Removing dry or oil bound distemper by scrapping sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete.

Painting 2 coats with oil type wood preservative of approved brand & manufacture on new work.

Applying priming coat consisting of a mixture of red lead, white lead and double boiled linseed oil in the ratio of 0.7 kg. 0.7 kg. 1 litre on wood work complete.

Applying priming coat with ready mixed primer of approved brand and manufacture on wood work complete.

Applying priming coat with ready mixed primer of approved brand and manufacture on steel work.

Painting two or more coats (excluding priming coat) with superior quality ready mixed paint for steel work of approved brand & manufacture in all shades on new work to give an even shade.

Painting (two or more coats) with synthetic enamel paint of approved brand and manufacture in all shade or new work over and under coat of suitable shade with ordinary paint of approved brand and manufacture to give an even shade

Painting three or more coats with acryllic exterior paint of approved brand and manufacture (Such as Dulex/ Asian Paints/ Sherwin Willians) including applying one coat of cement primer and one coat ofsurface treatment etc. complete.

Providing and applying white cement based putty of average thickness 1.00mm of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Melamine polishing on wood work (one or more coat)Matt

Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 mts. lead.

Demolishing cement concrete 1:3:6 or richer mix including disposal of material within 50 m lead.

Demolishing laterite stone masonry in cement mortar including stacking of serviceable material & disposal of unserviceable material within 50 mts. lead.

Dismantling wood work of sectional area 40 sq.cm. and above wrought framed and fixed in frames, other frames and trusses including stacking of material within 50 mts. lead (span upto 10 mtrs.)

Dismantling steelwork in single sections in channels, angles, tees and flats including dismembering and stacking within 50 mts. lead

Dismantling asbestos sheet roofing including ridges, hips valley and gutters and stacking the material within 50 meters lead.

Providing and fixing white vitereous china pedestal type (Europen type) water closet with seat as lid, whth C.I. brass hinges and rubber fitings15 lts white vitreous china low level flushing cistern with fittings as brackets 40 mm white precelain 3enameled flush bad, 25 mm overflow pipe with specials and mosquito proof coupling of approved municipal design complete, including cutting and making good the walls and floors where required.W.C. pan with white plastic seat and lid

Providing and fixing one piece construction white vitreous china squatting plate urinal with an integral longitudinal flushing pipe, 100mm dia half round channel, pvc. Automatic flushing cistern with fittings R.S. or C.I. brackets, standard size G.I. flush pipe for back and front flush with stadard spreader fittings, G.I. clamps, white vitreous china tiling 1200 mm high to front and side walls with white vitreous corners and angles set in neat cement standard urinal C.I. trap 65 mm diameter with vent arm & outlet grating & coupling in c.p. brass complete, including painting the cistern & fittings cutting and making good the walls and floors where required.Single plate with 5 litres pvc. automatic flushing cistern.

Providing and fixing vitreous china wash basin with RS or C.I. brackets painted white, 15 mm C.P. brass pillar taps C.P. brass chain with rubber plug 32 mm C.P. brass waste of pattern, 32 mm diameterM.I. or C.P. brass trap and union complete, including cutting and making good the walls where required.Flat back wash basin size 630 x 450mm with a pair of 15 mm C.P. brass pillar taps.

Providing and fixing G. I. Inlet connection for flush pipes connecting with W. C. pan.

Providing & fixing c.p. brass towel rail complete with C.P. brass brackets fixed to wooden cleats with C. P. brass screws750 x 20 mm size

Providing & fixing soap dish chromium plated with brackets fixed to wooden cleats with CP brass screw

Providing and fixing brass full way valve (heavy) duty with wheel of approved quality :50 mm nominal bore .

Providing and fixing ballvalve(brass)of approved quality :High or low pressure with plastic floats:25mm nominal bore

Providing and fixing P.V.C. connection pipe with brass unions 15 mm nominal bore:45 cm (18”) length .

Providing and fixing C.P. brass shower rose with 15 or 20 mm. Inlet:150 mm diameter.

Providing and placing on terrace roof of floor two (1st flor roof single piece rotational moulded polythene water storage tank having I S I mark and conforming to I S 12701; 1996.

Providing and fixing square-mouth S.W. gully trap grade ‘A’ complete with c.i. grating brick masonry chamber and water tight C.I. cover with frame of 300 x 300 mm size (inside the weight of cover to be not less than 4.53 kg). And frame to be not less than2.72 kg as per standard design :150 x 100 mm size –P or S type

Providing and fixing rigid PVC S.W.R. (soil, waste & rain water drainage pipes of approved including lubricant etc. complete (single/double) socketed:a)110mm dia

Providing and fixing rigid PVC S.W.R. (soil, waste & rain water drainage pipes of approved including lubricant etc. complete (single/double) socketed:b)75mm dia

Providing and fixing rigid PVC bend (approved make ) for S.W.R. pipes including lubricating etc complete bend with door :a)100mm dia

Providing and fixing rigid PVC bend (approved make ) for S.W.R. pipes including lubricating etc complete bend with door :b)75mm dia

Providing and fixing single tee of rigid PVC (approved make) for S.W.R. pipes including lubricating etc. complete, without door:110mm dia

Providing and fixing single tee of rigid PVC (approved make) for S.W.R. pipes including lubricating etc. complete, without door:75mm dia

Providing and fixing nahani trap of rigid PVC (approved make ) for S.W.R. pipes including lubricating etc complete, without door :110 mm dia

Providing and fixing U.P.V.C. pipe clips (approved make ) for S.W.R. pipes :110 mm dia

Providing and fixing U.P.V.C. pipe clips (approved make ) for S.W.R. pipes :75 mm dia

Providing and fixing R.P.V.C. vent cowl:a 110mm

Providing and fixing R.P.V.C. vent cowl:b75mm

Providing and fixing NICKEL chrome plated copper alloy Fancy BIB Cock Short Body Jaquar make or equivalent. Confirming to IS 8931;199315mm nominal bore

Providing and fixing NICKEL chrome plated copper alloy Fancy concealed stop cock with sheet flance 20mm Jaquar make or equivalent. Confirming to IS 8931;1993a)20mm nominal bore

Providing and fixing chlorinated ployvinyl chloride (CPVC) pipes confirming to IS:15778, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipes with clamps at 1 mt. spacing. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of the Engineer-in- charge. Concealed work (medium duty SDR 13.5 pipe) including cutting chases and making good the walls etc.c)25 mm dia nominal outer dia pipes.

Providing and fixing chlorinated polyvinyl chloride (CPVC) pipes confirming to IS: 15778 having thermal stability for hot and cold water supply includng all CPVC plain and brass threaded fittings CPVC solvent cement, trenching, refilling and testing of joints complete as per firectionof the Engineer in charge.(External work (heavy duty SDR 11 pipe)50 mm nominal outer dia pipes.

Providing and fixing 3 layer PP-R (Polypropylene Random copolymer) pipes SDR 7.4 UV stabilized & anti-microbialfusion welded, having thermal stabilityfor hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings i/c fixing the pipe with clamps at1.00 m spacing. This includes testing of joints complete as per direction of Engineer in charge. (Internal work - exposed on wall)PN-16 Pipe, 25 mm OD

Providing & fixing bevelled edge mirror of superior glass (5mm thk) of approved Quality, shape & size complete with CP brass screws and washers, Cleats, CP studs etc Complete.

Providing and fixing Hand Shower (Health Faucet) with 8mm dia, ABS/brass body with double lock 1.00m long Flexible tube (Brass plated stainles steel flexible hose) and wall hook of approved quality confirming to IS standards.

Providing and fixing NICKEL chrome plated copper alloy Fancy Two Way Bib Cock with single knob and wall flange conforming to IS 8931:1993 15mm nominal bore.

Solid PVC door frame in prelaminated colour : Providing and fixing factory made polyvinyl chloride (PVC) Door Frame in Prelaminated colour of the size 50mm width, 47mm height with a wall thickness of 5mm(±0.25), made out of extruded 5mm(±0.25) thick PVC Sheet of Density 600 Kg /Cbm Manufactured by an ISO-9000 certified Company , having pattam width of 50mm and thickness of 10mm providing weather seal Non-woven self adhesive gasket throughout the frame. All three frame lengths reinforced with 19mmx19mm M.S.square tube of 19 gauge. mitre cut at two corners and joined with 2nos. of 150mm long brackets of 15mmx15mm M.S. square tube. The door frame shall be fixed to the wall using 8/100mm long M.S. Screws through the frame by using PVC fasteners. A minimum of 4nos. of screws to be provided for each vertical member & minimum 2nos. for horizontal member etc. complete as per manufacturers specification anddirection of Engineer-in-Charge.

Providing and fixing 30mm thick FACTORY MADE BOTH SIDE PRELAM SOLID PANEL PVC DOORSHUTTER consisting of frame made out of M.S tubes of 19 guage thickness and, size 19 X 19mm for styles and 15 X 15mm for the top and bottom rails, M.S frame shall have a coat of metal primer of approved make and manufacture . M.S.frame shall be covered with heat moulded PVC ‘C’ channel made from 5mm(±0.25) thick sheet of density 600kg/cbm manufactured by an ISO- 9000 certified company, of size 30mm thickness, 50mm width to form styles and 5mm(±0.25) thick and 75 mm wide PVC sheet for the top rail, lock rail and bottom rail on either side of the panel . An additional 5mm(±0.25) thick PVC strip of 20mm width is to be stuck on the bottom side of the 'c' channel . Panelling of 5mm(±0.25) thick PVC sheet to be fitted inside the M.S frame welded/sealed to the styles and rails with 5mm(±0.25) x 30mm PVC sheet beading on either side and joined togther with solvent cement adhesive etc., 10mm thick ( 5mm(±0.25) x 2nos.) , 20mm wide cross PVC sheet as gap insert for the top rail & bottom rail. Door to be fixed to frames with 3 nos. M.S powder coated butt hinges of size 100mm*25MM*2mm using 32mm long steel screws drilled suitable to pass through both the walls of the M.S tube. Other hardwares should be fixed with 19*6mm size steelscrews, Complete as per direction of Engineer-in- Charge.

Supplying and fixing of Precast RCC slabs(factorymade,the factory should be ISO certified and registeredunder Dirctorate of Industries, Govt. of India) at site inconcrete Grade of M-25 with 20 mm nominal sizeGranitic or basaltic aggregate, consolidated by meansof mechanical platform, vibration etc. with liftinghooks of M.s. 10mm bars and PVC cups including costof reincforcement, Certificate from manufacturer shallbe produced indicating grade of concret and minimumcontent of steel in the product along with 5 year freereplacement warranty in case of breakage completeand as directed by Engineer -in -charge.Size 900 x 400 x 100 mm with steel reinforcement not less than 5.0 kgs per unit -12 T capacity

Supplying at store or site of work Rigid PVC(SEL FIT) pipes for public water supply includingRailway freight, carting, loading and unloading,stacking, transit insurance etc. complete,Conforming to IS: 4985-2000, and bearing ISImark, Class 6 kg/cm2(.i)200mm

Conveying carefully from stack at site, 250m fromboth sides rolling and lowering in trenches, layingand jointing true to line and level and perfect linkingof joints, including tack welding for mild steel pipesfor water supply pipeline complete in all respects asper the direction of the engineer in-chargeNominal diameter in mm a 200

Jointing of RING FIT PVC pipes by cleaning thepipes and hydraulic testing of joints etc. complete, asdirected by the engineer in-chargeOuter Diameter in mm 200

Wiring for light point/fan point/exhaust fan point/call bell point with1 .5sqmm FR PVC insulated copper conductor single core cable in PVC casing caping with modular switch,modular plate,suitable size modular surface box of specified category and earthing the point with 1.5 sq.mm FR PVC insulated copper conductor single core cable etc. as requiredb)Group B with Cat A Modular accessories

Wiring for 5A /15A plug with 4 x 4 sq.mm FR PVCinsulated copper conductor single core cable in PVCcasing capping alongwith 2 Nos of 4 sq.mm FR PVCinsulated copper conductor single core cable for loopearthing as required.

Wiring for circuit/ submain wiring alongwith earth wirewith the following sizes of FR PVC insulated copperconductor single core cable in the independent PVC casingcapping of appropriate size as required.b) 2 x 2.5 sq.mm + 1 x 2.5 sq.mm earthwire (20mm casing )

Supplying and fixing following modular switch/socket on the existing modular plate and switch boxincluding connections but excluding modular plateetc. as requireda) 5/6 A switch Cat A

Supplying and fixing following modular switch/socket on the existing modular plate and switch boxincluding connections but excluding modular plateetc. as requiredc) 15/16 A switch Cat A

Supplying and fixing following modular switch/socket on the existing modular plate and switch boxincluding connections but excluding modular plateetc. as requiredd) 3 pin 5/6 A socket outlet Cat A

Supplying and fixing following modular switch/socket on the existing modular plate and switch boxincluding connections but excluding modular plateetc. as requirede) 6 pin 15/16 A socket outlet Cat A

Supplying and fixing stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plates etc. as requireda)Cat A

Supplying and fixing following size modular GI boxalongwith modular base and cover plate formodulator switches in recess etc. as requiredc) 6 Module (200mm x 75 mm) Cat A

Supplying and fixing following size modular GI boxalongwith modular base and cover plate formodulator switches in recess etc. as requirede) 12 Module (200mm x 75 mm) Cat A

Supplying and fixing suitable size modular PVC box with modular plate and cover in front on surface or in recess including providing and fixing 3 pin 5/6A modular socket outlet and 5/6 A modular switch connection painting etc. as requireda)Cat A

Installation,earthing testing and commissioning of ceiling fan including wiring the down rod of standard length (upto 30cm) with 1.5 sq.mm FR PVC insulated copper conductor single core cable including providing and fixing phenolic laminated sheet cover on the fan box etc. as required

Installation,earthing testing and commisioning of resistance type ceiling fan regulator in existing swithch box including connection with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable earthing the regulator etc. as required.

Supplying and fixing extra down rod of 20 cmlength GI pipe 15 cm dia heavy gauge includingpainting etc as required

Supplying and fixing following way SPN sheet steel MCBdistribution board 240 V on surface/ recess completewith tinned copper busbar neutral busbar earth bardinnbar detachable gland plate interconnectionsphosphotized and powder painted including earthingetc. as required (but without MCB/RCCB/Isolator)4 way single door Cat B

Supplying and fixing B series SP MCB, 240 V, suitablefor lighting and other loads of following poles in theexisting MCB DB complete with connections testing andcommissioning etc as required"5 A to 32 A, Cat A

Supplying and fixing 6 A to 32 A, C series MCB suitablefor lighting and other loads of following poles in theexisting MCB DB complete with connections testing andcommissioning etc as required.TPN, Cat B

Supply of4 core armoured PVC/XLPEinsulated, PVC sheathed aluminium conductorcable of 1.1 KV grade with ISI mark conformingto IS:1554(Part I) ,IS:7098(Part I) with latestamendments of following size.4 Core 16 sq.mm

Laying of one number PVC insulated and PVCsheathed/XLPE power cable of 1.1 KV grade of sizenot exceeding 25 sq.mm on surface, etc. completeas required

Supplying and erecting of 48 inch(1200 mm sweep) ceiling fan,double ball bearing type,complete with all accessories(b)Cat B

Supplying and fixing surface mounted LED batten-tubes of 22 w jaquar glaze ultra(PC) or equivalent make including labour etc. all complete

Supplying and installation of Havells wall fanFlora neo 400mm or equivalent make including labour etc. all complete

M/S DOUBLE CENTURY CONSTRUCTIONS (BID ID -52919)