REPAIR TO FLOOR, JOINERY, RENDERING, PLUMBING, SANITARY FITTING WORKS IN OLD PROJECT AREA AT AF STN AT NAL

Amount

Demolition of RCC of any description and in any position not other wise specially provided for (reinforcement cut as required to facilitate demolition ) complete all as specified & directed.

Material and labour reinforced cement concerete1:2:4, type B-1 (nominal mix) using 20mm graded crushed stone aggregate) as in slabs supported on walls, beams, columns, shelves and like complete all as specified & directed. Note :- Reinforcement shall be measured and paid for separately under respective sch A item.

Use and waste of Formwork to soffits of suspended slab such as roof slab, floor slab, landing and similar work; flat rough finished surfaces of concrete complete all as specified & directed.

Use and waste of Formwork to edges of concrete flats, treads, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide, complete all as specified and directed.

Material and labour mild steel TMT Bars Fe550 10mm dia and over cut to length bend to shape required including cranking bending spirally for column, hooking ends & binding with and including mild steel mild steel wire (annealed) not less that 0.90 mm dia or securing with clips complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floor and paving n exc.15 cm thickness (Below or above ground level) and removing the rubbish outside MoD land complete all as specified & directed.

Material and labour 75mm thick PCC 1:3:6 type C-2 ( using 20mm graded crushed stone aggregate) as in plinth protection laid in alternate bays, surface finished even & fair without using extra cement including making joints complete all as specified and directed.

Material and labour 25mm thick PCC (1:2:4) type B-0 ( using 12.5mm graded crushed stone aggregate) as in sub base of floor surface finished even & rough to receive floor topping complete all as specified and directed.

M & L 15mm thick screed bed or bedding layer of mortar in cm 1:3 on brick/concrete surfaces as in sunken floor mixed with water proofing compound as per manufacturers instruction complete all as specified and directed. Note :- (WPC measured and paid separately)

Applying a tack coats of industrial bitumen 85/25 grade at the at the rate of 1.2kg per sqm as in sunken floor portion including preparation plaster concrete surface complete all as specified and as directed.

Supply only integral water proofing compound complete all as specified

Supply and fixings in repairs 40 mm bore 600mm long GI spout for drain out the surplus water from the sunken portion including cutting hole and making good the disturbed surface in cement mortar 1:3 or PCC 1:2:4 complete all as specified and directed.

Material and labour PCC 1:4:8 Type D2 (using 40 mm graded stone aggregate), as in mass concrete in sunken floor, complete all as specified and directed.

Dismantling floor, hearth wall tiling include cement mortar bedding (but not backing) removing serviceable tiles to store & rubbish off the premises. Note :- The demolished material should be disposed off outside MoD land. The contractor shall quote his rates considering the above element, no extra paid on this.

Material and labour Glazed ceramicColoured tiles 7 to 8mm thick in vertical surface of size exc 0.13 Sqm but n exc 0.18 Sqm thick set and jointed in neat cement slurry and pointed in white or colour cement to match, over and including 10mm thick rendering in CM 1:4 complete all as specified and directed.

Material and labour non-skid, ceramic coloured tiles 7 to 8mm thick (Square/rectangular ) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors, set and jointed in cement slurry and pointed in white or coloured cement to match with the shade of tiles laid over and including 15mm thick screed bed or bedding layer in cm 1:6 as specified and directed.

Material and labour non-skid, ceramic coloured tiles 7 to 8mm thick (Square/rectangular ) area of each tile exceeding 0.13 sqm but not exceeding 0.18 sqm, in floors, set and jointed in cement slurry and pointed in white or coloured cement to match with the shade of tiles laid over and including 15mm thick screed bed or bedding layer in cm 1:6 as specified and directed.

Material and labour non-skid, ceramic, coloured tiles 7 to 8mm thick (Square/rectangular ) area of each tile exceeding 0.13 sqm but not exceeding 0.18 sqm, as in skirting, set and jointed in cement slurry and pointed in white or coloured cement to match with the shade of tiles laid over and including 10mm thick backing coat on fair faces of brick work or concrete surface in CM 1:4 complete all as specified and directed.

Dismantling of stone slab and tiles of any description or thickness in floors aprons etc, laid bedded and pointed in any mortar complete all as specified and directed.

Material and labour 18 to 20 mm thick granite (of any type) work (table rubbed and polished) in steps, landings, window cills cooking plate form and like in cement mortar (1:4) including pointing in white cement (1:2) using marble duet with admixture of pigment to match with shade of granite laid over and including 15mm thick screed bed or bedding layer in cm 1:6, and including rounding of edges of granite slabs 10 to 20 mm thick by grinding and rubbing and finished smooth, coloured as approved by GE all as specified and directed. Note: Front facia edges of granite slabs shall be rounding and finished smooth. The contractor shall quote his rates considering the above element, no extra paid on this.

All as per description of serial Item no. 20.00 here in before but as on vertical surfaces and over 10 mm thick rendering in CM 1:4.

Taking down cement plaster on brick or stone walls/ceiling etc including racking out joints, hacking for key, scrubbing down with water etc, Note :- The demolished material should be disposed off outside MoD land. The contractor shall quote his rates considering the above element, no extra paid on this.

Demolition of brick or stone masonry built in cement mortar incl all quions, arches, pillar etc. complete all as specified & directed.

Material and labour brick work with sub class -B bricks old size, straight or curved on planexc 6m mean radius built in CM 1:6. complete all as specified & directed.

All as per description of serial Item no. 24.00 here in before but as in half brick thick wall built in CM 1:4 complete all as specified & directed.

Material and labour for repairing of soffits of slabs and similar works by dismantling of loose/ disintegrated portion of RCC at any height and in any situation, including provn of support, formwork and welding of reinforcement and fixing in position and with provision of weld mesh, applying dubbing 1st coat of 20 to 25mm thick in CM 1:3 finished rough and finishing coat of 10mm thick in CM 1:3 finished even and smooth without using extra cement over and including cement slurry @ 3 kg/sqm, finished even and smooth to desired shape and applying two coats of weather proof exterior emulsion paint over a coat of acrylic resistant primer to match with existing surfaces complete all as specified and directed.(weld mesh measured and paid separately) Note:- (i) Unit rate of this item includes the cost of scaffolding, formwork etc. and nothing extra shall be paid on account of variation in height. (ii) For payment purpose, the area of finished plaster in 2nd coat shall be considered.

Material and labour for Hard drawn steel wire fabric (weld mesh) of weight not less than 3 kg/ sqm and not exc 4 Kg/ sqm cut to lengths, bent to shape required and tying with and including mild steel wire (annealed) not less than 0.9mm in dia supplied and fixed in reinforcement including necessary fixing arrangements etc complete all as specified and directed.

Material and labour 15mm thick rendering on brick work or concrete surface in cm 1:6 to be finished even and smooth without using extra cement complete all as specified and directed.

Material and labour 10mm thick rendering on concrete surface in cm 1:3 as in ceiling surface to be finished even and smooth without using extra cement complete all as specified and directed..

Material and labour 15mm thick rendering on fair faces of brick work or concrete surface in cm 1:4 to be finished even and smooth without using extra cement complete all as specified and directed.

Material and labour Preparing surface of new plastered surface and applying two coat of oil bound distemper over one coat of primer complete all as specified and directed.

Material and labour three coats of white wash on newly plastered surfaces of ceiling including preparation of surfaces complete all as specified and directed.

Material and labour Preparing surface of new plastered surface and applying two coats of acrylic emulsion exterior paint over coat of primer, tint as approved by GE in camouflage pattern to match existing surface complete all as specified and directed.

Material and labour preparation of plastered or unplastered old decorated surfaces of walls including brooming down or steel wire brushing; scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots as required, and applying two coat of white lime wash complete all as specified.

All as item No 34 above but as in ceiling.

Material and labour preparation of plastered or unplastered old decorated surfaces of walls including brooming down with steel wire brushing scrapping down smoke soot moulds moss and efflorescence salts and trading oil and greasy spot including washing, rubbing down and stopping the connected previously treated surfaces and applying two coat of oil bound distemper emulsion complete all as specified

Taking down chowkats or frames but with shutters (with out taking off shutter from the frames) not exc 1.5 sqm each complete all as specified and directed.

Taking down chowkats or frames but with shutters (with out taking off shutter from the frames) Exc 1.5 sqm but n. exc 4 sqm each complete all as specified and directed.

Taking down shutters of any description exc 1sqm but n. exc 2 sqm each complete all as specified and directed.

Supplying & fixing 1.25 mm thick Pressed Steel door frames size 105x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc including filling back hollow with PCC 1:3:6 type C-0 using 12.5 mm graded stone aggregate complete all as specified.

Supplying & fixing 1.25 mm thick Pressed Steel door frames size 125x60mm for double doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc including filling back hollow with PCC 1:3:6 type C-0 using 12.5 mm graded stone aggregate complete all as specified.

Supplying & fixing solid PVC door frames of sizes 50mm x 47mm made out of 5mm single side prelam PVC sheet used instead of plain colour PVC sheet & edges will be painted to match with prelam sheet reinforced with MS Square tube complete all specified and as directed.

S & F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing but both side Prelam PVC sheet used instead of Plain colour PVC sheet. Stile and rails feathered at edge complete all specified and as directed.

S&F factory made 30mm thick flush shutters, solid core construction, with particle board core and plywood face panels, commercial type on both face is covered with decorative face veneer with lipping/frame to match sides include for the provision of suitable blocks for taking mortice locks, latches, or other fittings complete all as specified and directed.

Dismantling boarding, any description any size , fixed in any position with screws complete all as specified .

M&L for Block boards 18/19 mm thick ,Prelaminated particle board, interior grade, prelaminated on both sides with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work complete all specified and as directed.

S&F Continuous (piano) hinges 30 mm width of flaps, mild steel, bright finish or electro galvanised with Cup Board or drawers complete all as specified complete all specified and as directed.

M & L for providing cupboard shutter/ Kitchen Cabinate in required size at site made out of 18 mm thk PVC colour sheet and provision of shutters one side decorative pre laminated PVC sheet and all required brackets SS screws etc. The pannels shall be fabricated using adhesive and screws where required. All the edges shall be covered with 2 mm thk edge bonding tape or 90 degree edge bent finish as per make and specification mentioned as per drawing and specification approved by Engr-in-charge.

Supply Only Auto closes clip on cabinet hinges (regular) for kitchen cabinet shutters Make: Hettich / Godrej/ Ebco Note : Each pair means one piece fixed on openable shutter and other piece fixed on fixed portion.

Supply Only Stainless Steel (SS 304) handles 100 mm size for Kitchen Cabinet Shutters. Make: Hettich / Godrej/ Ebco

S & F in repair pressed steel factory made cupboard shutter with frame of 1.25 mm thick and shutter 1 mm thick PBI sheet with hinges 6 nos of 3.15 mm thick and 100 mm long steel (hinges godrej pattern ) locking arrangement incl 12 mm dia vertical rod incl spray painting in factory of approved colouras directed by Eng-in-Charge complete all as specified. Make : Godrej or equivalent

S & F 2nd class hard wood 35mm Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all specified and as directed.

S&F 35 mm thick 2nd class hardwood, Plain, framed, panelled shutters (any number of panels), in with panels of timber flat on both sides (feather edged), of 12 mm BWP commercial ply with commercial veneering on both faces; supplied and fitted to chowkats

S&F factory made box type steel window 1.25mm thick ERW hollow P section of each frame size 60mmx25mm including grill using 10 sqmm bar double rebated both guage and glass shutter comprised gauzed glazed & Skelton shutter ERW section 50mmx20mm & 1mm thick with two openable leaf consisting of two number sash bars of T-Section 20mmx3mm complete welded to frame with one vertical mullion of ERW box type T-Section of size 60mmx25mm and 1.25mm thick with following fittings welded to the frame shutter :- i) Hold fast 150mm long mild steel flat iron 12x3 mm made to shape- 04 Nos per window. ii) Handle of Z section 20mmx25mm, 100mm long – 01 No per leaf. iii) MS tower bolt 150mm long 2 No per leaf. iv) Z section 20mmx25mm, 100mm long stopper – 01 Nos per leaf. v) Cleat 55 mm long of solid square 15x20x.63mm square - 01 Nos per leaf vi) MS pintal hinges 12 x 75 mm - 2 Nos each leaf vii) 10 mm squre guard bar @ 10 cm c/c viii) 25 x 3 mm flat iron for joint of both frame wire mesh & Glazed welded inner side and outer side of frame (ix) 0.36 mm nominal dia of stainless steel wire mesh and average width of aperture 1.40 mm fixed in glazed/gazed Skelton shutter of window (x) 3mm thick sheet glass ordinary quality and with oil putty in square n exc 0.50 sqm in each pane fixed in glazed /gauge Skelton shutter of window xi) Fabrication and fixing arrangements as per specification including taking down, cutting holes and making good dismantled portion in PCC 1:2:4 type B-1 /cement plaster 1:4 as require and make finish good to the existing surface complete all as specified and directed. Note: (i) The mode of measurement shall be only one for the set of two i.e wire mesh window and glass window at one location and nothing extra shall be measured on this account.

S & F mild steel box type ventilator partially fixed with glass and partially with two leaf for glass & gauzed top hung type complete all as specified per item ser No 54 above

Material and labour for surfaces of any description not other describe over 10cm width or girth and applying two coat of synthetic enamel paint over one coat of pink primer, including preparation of new wooden surface.

Material and labour for surfaces of any description not other describe over 10cm width or girth and applying two coat of synthetic enamel paint over one coat of red oxide, including preparation of new steel surface.

Taking down shutters of any description exc 1sqm but n. exc 2 sqm from chowkat and re-fixing in same opeing after re-securing or easening and adjusting including repair complete all as specified.

Supply and fixing butt hinges extruded aluminium alloy with galvanised mild steel hinge pin anodised and fixed ,100mm, ISI marked, fixed with stainless steel screws complete all as specified and directed.

Supply and fixing 200mm long aluminium anodised barrel tower bolt, extruded section,fixed with stainless steel screws complete all as specified and directed.

Supply and fixing 150 mm size extruded aluminium aluminium alloy handles fabricated type, anodised fixed with stainless steel screws complete all as specified and directed.

Supply and fixing 300mm aluminium alloy, anodised sliding door bolt with hasp staple (bolt type) fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed with stainless steel screws complete all as specified and directed.

S&F in repair Ball magnetic catcher with 8mm dia steel ball, brass body and striking plate fixed with brass screws or with adhesive complete all as specified and directed.

Supply and fixing in repair 150mm long Hasp and staple stainless steel safety type bright including bolt to hinge plate and fixed with fixed with stainless steel screws complete all as specified and directed.

Supply and fixing in repair steel window handle (Left & Right Shutter) complete all as specified and directed.

Supply and fixing in stainless steel wire cloths 0.36 mm nominal dia of wire and average width aperture 1.40mm and fixed with stainless wire staples complete all as specified and directed..

All as per description of serial Item no. 66.00 here in before but as in repairs.

Supply and fixing In repair 140mm long floor door stopper of aluminium alloy body and toungue, anodised with hard drawn steel spring, fixed to door shutter fixed with stainless steel screws complete all as specified and directed.

S&F 3.0mm thick sheet glass ordinary quality and glazing with oil putty in square n exc 0.50 Sqm in each panes complete all as specified and directed and Hacking out old broken glass (any thickness size quality or description) from wooden frames or stone, concrete or brick surrounds glazing with putty or fixed with beads.

S&F in repair Stainless steel (Grade 305) curtain rods 25mm dia 0.80mm wall thick mild steel chromium plated incl supporting brackets complete all as specified and directed.

S&F in repair Stainless steel (Grade 305) Ornamental type brackets (Open Ends) suitable for curtain rods of 25mm dia all as specified and directed.

S&F in repair Stainless steel (Grade 305) brackets (Dead Ends) suitable for curtain rods of 25mm dia all as specified and directed.

S&F mild steel 300mm, ordinary rat tail rod pattern springs, including roller and roller plate complete all as specified and directed.

Ditto all as above Item No 74 but in repair.

Taking up or down 15 mm dia steel tubing & connections including clearing for refixing or removal to store.

All as per description of serial Item no.76.00 here in before but 20mm bore tubes.

S & F 15mm bore of tube medium grade galvanized with all fittings & fixed complete to walls & ceiling or laid in floors complete all as specified and directed.

All as per description of serial Item no. 78.00 here in before but 20mm bore tubes.

Dismantling water tanks any type of capacity Exc 250 but n.exc 500 liters

S&F 500 litre capacity Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) triple layered white, hoisted and fixed in position, including 20 mm bore Ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe complete all as specified and directed.

S&F 20mm PTMT nipple suitable for HDPE water tank (minimum weight 45gms) complete all as specified .

S&F in repair PVC (PTMT) float valve, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed suitable for 20mm bore pipe, complete all as specified and directed

S&F in repair 15mm bore long body Angle cock fancy type chromium plated screwed down high pressure complete all as specified

S & F in repair long body stop valve15mm bore fancy type chromium plated with long shank and cup (concealed type) screwed down high pressure, with crutch or butterfly handle screwed both ends for iron pipe or for unions complete all as specified and directed.

S&F in repair Bib tap standard of PTMT any colour high pressure screwed for iron pipe and fixed. (Minimum weight 15mm-90gms/20mm- 125gms) complete all as specified

S&F in repair 15mm long body bib taps long shank cast copper alloy with crutch or butterfly handle screwed for iron piper or for brass ferrule complete all as specified and directed.

S&F in repair Pillar taps long body fancy type with capasten head chromium plated screwed down high pressure with without lettered 'Hot' or Cold with long screwed shanks and fly nuts screwed for iron pipe and fixed

S&F in repair vitreous china wash down water closet (pedestal pattern) with plastic seat and cover including complete as directed by Engr-in-Charge.

S&F in repairs 15mm bore PVC connection pipe 450mm long with PTMT nuts at both ends complete all as specified and directed.

S &F in repair chromium plated shower rose 125mm size with or without swivel joints and shower rod, any size including fixing to 15 mm bore steel pipe or union

S& F In Repair Chromium Plated Soap Dish Design approved by Engr in Charge complete all as specified and directed by Engr in Charge.

S & F in repair towel rail 20mm dia chromium plated including 600mm long including brackets, screws and wooden/plastic cleats

S&F in repairs 100 mm dia Stainless steel grating complete all as specified.

S&F in repairs 75 mm dia Stainless steel with hole grating complete all as specified.

S&F in repairs waste down pipe 32mm bore for wash basin/sink complete all as specified and directed

S& F in repair vitreous china squatting pan Orissa pattern size 580 x 440mm white, with integral foot rests excluding flushing cistern and flush pipe but including traps as required complete all as specified and directed

S & F in repair 10 Litre capacity PVC valveless symphonic action type flushing cistern low level white with inlet ball valve and brackets and connection to pipe, float and handle, L-Bend complete all as specified and directed

S&F in repairs vitreous china wash basin, white, flat back, size 580x450mm excluding taps waste, chain and plug and porcelain stopper but including bracket complete all as specified and directed

Demolition up to 100/75mm bore and breaking up drain pipes (AC/reinforced concrete/salt glazed ) complete all as specified and directed

S & F 110mm bore PVC SWR Pipes single socketed, in any length with rubber ring joints, fixed to walls complete all as specified and directed

S & F 75mm bore PVC SWR Pipes single socketed, in any length with rubber ring joints, fixed to walls complete all as specified and directed

S & F 110mm bore PVC SWR Junction single (Single T) with access door complete all as specified and directed

S&F PVC (SWR) bends of 110 mm bore complete all as specified and directed

S&F PVC (SWR) bends of 110 mm bore with access door complete all as specified and directed

S&F PVC (SWR) bends of 75 mm bore complete all as specified and directed

S&F PVC (SWR) bends of 75 mm bore with access door complete all as specified and directed

S&F PVC (SWR) bends of 110 vent cowl complete all as specified and directed

S&F PVC (SWR) bends of 75 vent cowl with access door complete all as specified and directed

S & F in repair 75mm bore PVC (SWR) floor trap, with grating plain/ whole including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed.

S&F as in repair stainless steel plate rack, made out of 0.80mm thick of size 31"x36"x10" complete all as specified and directed.

S&F in repair sinks with drainage board made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mmcomplete all as specified and directed.

Taking down aluminium shutter / sliding door for necessary repair work and re-fixing in position after adjusting or replacing defective members of rails or styles in position with replacement of steel screw re threading and fixing on existing devices, resetting or replacing top pivots bottom steel plates etc and resetting or replacing glazing etc for proper function of aluminium door of size n exc 1.5 sqm each complete all as specified. Note :- Supply only aluminium section, glazing and top pivots shall be measured and paid separately.

Supply only double action floor door spring hydraulically regulated made up minimum 1.25 thick aluminium alloy sheet foundation box, main body stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty complete all as specified

Supply only top pivot of casting body suitable for aluminium door complete all as specified and directed.

Supply only 4.80 mm thick sheet glass of ordinary quality plain / tinted and glazing with rubber beads,n exc 0.5 sqm in each, clips etc complete all as specified and directed. Note: Cost of rubber beads, clip included in unit quoted rate of this item.

S & F as in repairs mild steel mortice lock vertical type 100mm, 4 levers complete all as specified and directed.

Taking down aluminium door/window with shutter of any size complete all as specified and directed.

Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) work for Frame of doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ panelling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Chief

Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ panelling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-Chief.

S & F as aluminium grill of size, 50mm x 50mm and 8mm thick hexagonal shaped mesh, fixed to aluminium frame work with 'Y' and 'U' clip of size 15mmx12mm & fastners complete all as specified and directed.

S&F concealed lock (push to unlock) for sliding window made with zinc body, aluminium hook and anti rust material with power coated metallic finish of approved colour having size 100mm x 24 mm incl necessary cutting for fixing all as specified and directed.

S & F double action floor door spring hydraulically regulated made up minimum 1.25 thick aluminium alloy sheet foundation box, main body stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty complete all as specified

S & F top pivot of casting body suitable for aluminium door complete all as specified and directed.

Supply and fixing 200 mm size extruded aluminium alloy handles fabricated fancy type, anodised fixed with stainless steel screws complete all as specified and directed.

S & F 5 mm thick high quality, durable acrylic panel sheet and glazing with rubber beads, clips etc complete all as specified and directed.

S & F 4.80 mm thick sheet glass of ordinary quality plain / tinted and glazing with rubber beads, clips etc complete all as specified and directed. Note: Cost of rubber beads, clip included in unit quoted rate of this item.

S & F in repair steel mortice lock vertical type 100mm, 4 levers all as specified complete all as specified and directed.

Dismantling structural steel work including doors, gates but excluding framed truss etc

S&F framed work as in gate (ornamental design) of angle or other section with gussets plates, rails, braces etc complete drilled for fixing of steel sheeting or other covering. Doors etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings and hanging also fastening and fixing complete of quality grade B.complete all as specified and directed. Note:- The ornamental design shall be approved by Enggr-in-charge before exection of work.

SHREE GURU NANAK CONSTRUCTION COMPANY

Surya Buildcon & Engineers

Beenu Co. Company

m/s gaurav enterprises

MANOJ ENTERPRISES

SUMIT ENTERPRISES