Construction of sample drain from RD 0 to 11500 by laying underground 800 mm dia RCC Np-3 pipeline outfalling at RD 13000 L of Dadri Feeder.

Amount

Earth Work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead up to 50 m and lift up to 1.5m, as directed by Engineer-in-charge. All kind of soil. All kind of soil including refilling & dewatering of SSWL as per site condition hsr 4.12.1

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work below plinth level and up to Floor IV level : 1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size) HSR 6.1.2

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work below plinth level and up to Floor IV level : 1:3:6 (1 cement : 3 coarse sand (zone-III) : 6 graded stone aggregate 20 mm nominal size) HSR 6.1.4

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. All works up to plinth level (Hodi slab should be provided in two or more parts & each part should have separate iron hook for lifting complete in all repect HSR 6.25.1

Brick work with common burnt clay modular bricks of class designation 7.5 in foundation and plinth in BM 1:4 Provide steel step at 1 ft. interval as per height in each hodi. Complete in all respect for manual movement in hodi. HSR 7.20.1 HSR 7.20.1

Brick work with common burnt clay non-modular bricks of class designation 7.5 in superstructure above plinth level up to floor IV cement mortar 1:4 HSR 7.22.1

12 mm cement plaster of mix 1:4 (1 cement: 4 coarse sand) HSR 11.8.1

Centering and shuttering including strutting, propping etc and removal of form work for Foundation, footing, bases etc HSR 6.29.1

Centering and shuttering including strutting, propping etc and removal of form work for Lintels, beams, plinth beams, girders, etc HSR 6.30.5

Steel reinforcement for R.C.C. work, where not included in the complete rate of RCC, including straightening, cutting, bending, placing in position, binding, wastage, overlaps, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire etc. complete in all respect above plinth level.Thermo-echanically Treated bars of grade Fe-500D or more. HSR 6.34.6

Providing lowering cutting jointing and testing RCC pipe class NP3 800 mm diaas per IS-458-2003 with spigot & socketed jointsmanufactured with ISI markedsulphate esistance cement as per ISI 12330 with rubber rings ISI markedacement sandmortar and with end dowels filled with 1:3/2 cement sand mortar andfinishing the joints at an angle of 45 egree withdiametric of the sewer being: 800 mm dia pipe testing of water leakage HSR 21.95.7

Providing and laying in position ready mixed plain cement concrete, with cement content as per approved design mix and manufactured in fully automatic batching plant and transported to site of work per IS : 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineer-in-charge M-15 grade plain cement concrete (cement content considered @ 240kg/cum) HSR 6.22.1.2

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, as per direction of Engineer-in-charge. All works above plinth level up to floor IV level HSR 6.25.2

Designing, Providing, installing and fixing factory finished customed design Pregalvanized high tensile steel joists manufactured from G350 Z275 confirming to IS:277-1992, minimum coating of galvanizing 275 gm/sqm, minimum yield stress 35 MPa & minimum tensile strength of 380 MPa placed 1.23 metre apart to support the load of slab etc as per the design & directions of Engineer-in-Charge. HSR 32.25

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor four level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size). HSR6.16

Plane C.Conc. 1:1 1/2:3 for road requrring HSR 6.1.1

Laying Earth on roof @ 197+30 = 210 HSR4.35+4.35.1

10 cm thick (average) mud phaska of damped brick earth on roofs laid to slope consolidated and plastered with 25 mm thick mud mortar mixed with bhusa @ 35 kg per cum of earth and gobri leaping with mix 1:1 (1 clay : 1 cow dung) and covered with flat tile bricks, grouted with cement mortar 1:3 (1 cement : 3 fine sand) mixed with 2% of integral water proofing compound by weight of cement and finished neat: HSR 9.11.1

Pointing on brick work or brick flooring with cement mortar 1:3 (1 cement : 3 fine sand): Flush / Ruled/ Struck or weathered pointing HSR 11.25.1

Providing and fixing on wall face Unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes 110 mm diameter HSR 9.57.2

Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete 100 mm dia HSR 22.55.1

Providing & Laying base course of floors consisting of 100mm thick CC 1:8:16 and 100mm sand and stone filling HSR 10.1

Providing and laying cinglomerate floor 50 mm thick CC topping 1:2:4 HSR 10.7

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade New work (two or more coats) over and including water thinnable priming coat with cement primer HSR 11.64.1

Painting with silicon & acrylic emulsion based water thinnable sealer of approved brand and manufacture on wet or patchy portion of plastered surfaces 2 Coat HSR 11.72.2

Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters. HSR 13.37.1

Providing and fixing ball bearing for rolling shutters. HSR 13.38

Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer Using M.S. angels 40x40x6 mm for diagonal braces HSR 13.6.1

Painting on G.S. sheet with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade HSR 11.99.1

M-15 grade plain cement concrete (cement content considered @ 240 kg/cum) HSR 6.22.2.2

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete. HSR 9.18

Providing and fixing fan hook made from 8 mm dia MS rod 75 cm long of required shape and size HSR 23.23.4

Electricity Provision including fitting of 2 No. fan, 2 No. tubelight, 4 No. CFL, 3 No. pin plug, 2 No. Power plug (Complete in all respect) and other as per instruction by Engineer in charge.

Wire mesh (rabbit) HSR B0472

Dismentalling of Road HSR 17.43.2

MAHA LAXMI CONSTRUCTION COMPANY

PARMIL KUMAR