Ambattur Bus Stand

Amount

Dismantling removing the existing Reinforced Cement Concrete work etc., by using required mechinaries including stacking of steel bars and disposal of unserviceable material within 50m lead , labour charges, as per direction of Engineer in charge.

Removing the excavated earth and depositing the same Upto 4 to 6KM with an average lead of 5 KM from the site including loading and unloading etc., all complete and as directed by the Engineer - in - Charge.

Surface dressing of the ground including removing vegetation and in-equalities not exceeding 15cm deep and disposal of rubbish, lead upto 50m and lift upto 1.5m all kinds of soil

Earth work excavation for foundation in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by the departmental officers with an initial lead of 10 mts and initial lift of 2 mts. and clearing and levelling the site, etc., complete complying with standard specification.

Foundations, Grade beam, Sump, Septic Tank, Compound wall - First Depth Upto 2m

Filling with filling sand (M Sand) in foundation and basement in layers not exceeding 15cm in depth and each layer to be well watered, rammed and consolidated as directed. Rate to include materials, loading, unloading, transportation, plant and machinery, hire and fuel charges for tools and plants and other incidental charges, royalties, seignorage and taking statutory approvals as necessary to carry out the work as complete with all respects complying with relevant standard specification, as directed by the Client / Engineer-in-charge.

Supplying and filling of Gravel by lorry in basement filling including conveyance loading and unloading consolidating with larger of 300mm thick charges and all other incidential charges laying watering labour and consolidation etc., complete as directed by the Dept., Officers with standard specification.

Providing Pre construction Anti termite treatment for the building including all chemicals as per standard specifications. Labour charges for preparing the areas for treatment spraying chemicals and other incidential charges etc., complete. The rate shall be inclusive of giving anti-termite treatment to the building for the following four stages including breaking the termite mounds making holes with crow bars at an intervel of 12"to a depth of 8" in the periphery of building and pouring chemicals etc., complete as per ISI 6313-1981 and. The antitermite chemicals used should have 0.5% concentration with 3L solution for the entire operation etc. as directed by the Engineer incharge and including cost of chemicals labour transportion etc.,

Stage:1 Spraying Anti-termite treatment chemicals solution for the foundation before laying the foundation concrete bottom and sides of the foundation. Stage:2 Spraying anti-termite chemicals solution to the grade beams level spraying has to be done for the grade beams brick masonry in the superstructure in contact with back fill earth. Stage:3 Spraying anti-termite chemicals solution on sand for the flooring before laying the flooring concrete. The treatment has to be carried out on the sand filling the basement after leveling operation is over. Stage:4 Spraying anti-termite chemicals solution around the building outside of the building by making crow bar holes at an intervel of 12" to a depth of 8" around the building before laying the plinth projection. This holes has to be be closed after the treatment.

Providing and laying plain cement concrete 1 : 4 : 8 (1 of cement : 4 of sand, 8 graded stone aggregate 40mm nominal size) in foundation and basement including dewatering wherever necessary and laid in layers not more than 15 cm thick and consolidation etc.

Construction of Wet Mix Macadam 250mm compacted thickness in two layers by providing , laying , Paving , and compacting of aggregate gradation satisfying to Table 400-13 of MORTH and satisfying the physical paraeteres as per MORTH Table 400-12, mixing in a Wet Mix Plant of 200 tonne capacity at OMC , carriage of mied material to work site and laid in sensor pavers to the required line and grade as per the drawing and compacted with vibratory roller of 8-10 tonne to achieve the desired density of 98% of Maximum dry density and as per the direction of the Engineer-In-Charge of work.

Providing formwork for centering shuttering etc. for all RCC works including strutting for height upto 3.29m using mild steel sheets of size 9 90 X 60 cm 10 gauge stiffened with MS angle of 25 X 25 X 3mm for boarding, laid over adjustable span & jacks and supported by 50mm dia pipes for general pipes scaffolding systems @ a spacing of 1.20m c/c and vertical connected at a height of 2.0m c/c including 'C' & 'U' clamps and base receiver cup at bottom for connecting pipes etc and removable systems etc., Rate to include all materials, labour charges, wastages , placing, transportation, lead & lifts, tools & plants, fuels, fixing in position at all levels, heights, masking tape in sheet joints, consumables, etc. as complete with all respects complying with relevant standard specification, as directed by the Client / Engineer-in-charge.

For footing, Grade beam, Column, bed blocks templates staircase, steps piers, raft beam, raft slab etc.

For Plane surfaces such as RCC floor slab, roof slab, beams, lintels, bed blocks, landing slab, waist slab, portico slabs and beams, etc.

for plane surfaces such as rectangular or square rcc columns, sunshades & etc.

For plane surfaces such as vertical slab, side slabs of boxing, vertical drops, facia, vertical walls etc.

Providing and Laying M 30 Design Mix for all reinforced cement concrete with minimum cement content conform to IS 456-2000 using ordinary Portland cement of grade 53 from approved manufacturer, manufactured sand, 20 mm and down graded size coarse aggregates, necessary approved admixtures as per requirement. works for Raft, Grade beam, Shear wall, RCC walls, Lift walls, Plinth beams, Column, footings, Grade slab, Roof slab & beam, Curved slab, beam, Column drops, Pergola, Staircase waist and landing slab lintel, Sunshades, parapet Cum drops, Steps, canopy, window boxing slab, Loft, fins facia Planter box binders basement retaining wall, machine foundation, elevation features and other similar structures etc..excluding necessary centering, shuttering and reinforcement which shall be measured and paid separately under relevant items. Rate to include all designing the mix, batching plant, mechanical mixing, transporting and placing at all levels, leads, lifts, tools & plants, fuels, all materials, labour charges, wastages , laying, pumping the concrete to all levels, providing sleeves / openings in RCC slabs, compaction by vibrator, curing etc. as complete with all respects complying with relevant standard specification, as directed by the Engineer- in-charge

Footing and grade beam &Ground Floor

Ground Floor

First Floor

Terrace Floor

Providing and Construction of dowel jointed, Pavement Quality Concrete of 280mm thickness over a prepared Base Course with 43/53 grade cement , coarse and fine aggregate conforming to IS 383, coarse aggregate 25 mm & 12.5 mm Granite/Basalt/Trap metal & clean sieved approved sand conforming to the gradation as specified in Table 600-3 of MORTH clause 602,. loading materials to cement concrete batch mix plant of adequate capacity ( normally 25% more capacity than the paving equipment preferably 120 Cum/hour ) as per approved mix design satisfying the characteristic flexural strength of not less than 4.2 Mpa. The mix shall be transported to site in transit truck /tippers/ dumpers of 5-6 Cum capacity, laid with a slip form paver with electronic sensor fitted with vibrators shich shall operate at a frequency of 8000-10000 impulses per minute under load with a maximum spacing of 600mm and finished in a continuous operation including provision of contraction, expansion, construction and longitudinal joints, fixing of Dowel bars and Longitudinal tie bars ,joint filler, separation membrane, sealant primer, joint sealant, debonding strip, curing compound as approved, finishing with power trowel to the required grade, level and alignment, textured with texturing machine, finishing etc.,

making groove cutting for construction joint of size (4 x 10mm) and filling the same with polyurethene sealent, making groove cutting for expansion joint of size (8 x 10mm) and filling the same with polyurethene sealent, providing Isolation joint of 20mm wide to the full depth of the concrete and fixing with isolation pad of 20mm thick and sealing the top with polyurethene sealent to the size of 20 x 20mm and curing (curing shall be as per clause 602.9.12 of MORTH) including cost of all materials, labour, lead and lift, hire charges of machineries , including the initial saw cut and filling of Polysulphide/Polyurethene sealants in contraction, expansion joints etc., complete in accordance with MORT&H technical specification clause No. 602 and with all other incidental charges inclding the trial length and as per the direction of the Engineer-In-Charge of work. (Reinforcement and Dowel bars shall be paid under relevant item)

For Road Pavements

Supplying, fabricating and fixing in position of steel Fe 500 grade Reinforcement for all RCC work with Thermo Mechanically Treated Bars (TMT) conforming to IS 1786 of latest version according to drawings and binding the reinforcement with 18 gauge double fold GI binding wire and providing Concrete / PVC cover blocks to maintain the cover as required.Rate to include all bending, tying grills, placing, transportation, lead & lifts, tools & plants, fuels, all materials, labour charges, wastages , laying at all levels, fixing in position, cost of cover blocks, etc. as complete with all respects complying with relevant standard specification, as directed by the Engineer-in-charge.

Supply and constructing cement concrete solid block masonry work at all levels in cement mortar 1:5 (1 of Cement : 5 of manufactured sand ) using Portland Pozzolana Cement standard size of 400 x 200 mm and 200 mm thick of solid cement concrete with minimum compressive strength of 5 N/Sq.mm.conforming to IS 2185 or equivalent BS and Fly ash conforming to IS : 3812 (Part III)-1966* may be used for part replacement of fine aggregate up to a limit of 20 percent complete and as directed. Concrete blocks manufactured under strict quality control conditions using modern rugged block casting and stripping machine with the latest moulding techniques etc,. only shall be used. Rate to include all materials, labour charges, wastages for working at all levels with necessary lead and lifts, transportation charges, loading, unloading, scaffolding, staging, curing, fuel, consumables as complete with all respects complying with relevant standard specification and as directed by the Client / Engineer-in-charge.

BASEMENT & GROUND FLOOR

FIRST FLOOR

TERRACE FLOOR

Supply and constructing cement concrete solid block masonry work at all levels in cement mortar 1:5 (1 of Cement : 5 of manufactured sand ) using Portland Pozzolana Cement standard size of 400 x 100 x 200 mm of solid cement concrete blocks, with minimum compressive strength of 5 N/Sq.mm.conforming to IS 2185 or equivalent BS and Fly ash conforming to IS : 3812 (Part III)-1966* may be used for part replacement of fine aggregate up to a limit of 20 percent. Concrete blocks manufactured under strict quality control conditions using modern rugged block casting and stripping machine with the latest moulding techniques etc. only shall be used. Rate to include all materials, labour charges, wastages for working at all levels with necessary lead and lifts, transportation charges, loading, unloading, scaffolding, staging, curing, fuel, consumables as complete with all respects complying with relevant standard specification and as directed by the Client / Engineer-in-charge.

GROUND FLOOR

FIRST FLOOR

Special ceiling plastering and finishing all RCC exposed surface such as RCC slabs, sunshades, canopies, staircase, steps, landing slabs etc., with CM 1:3 according to the specification. Rate including all materials, labour charges, wastages, necessary lead and lifts, working at all levels, transportaion charges, loading, unloading, preparation of surface, ncessary haccking in RCC surface, scaffolding, stagging, providing drip bands, moulds to any size and shape as shown in drawings tools and plants, fuel, curing, cleaning, consumables etc as complete with all respects complying with relevant standard specification and as directed by the Client / Engineer-in-charge.

Plastering the internal wall surface in cement mortar 1:5 (one cement:five sand) 12mm thick in all floor levels including curing complying with standard specification Rate including all materials, labour charges, wastages, necessary lead and lifts, working at all levels, transportaion charges, loading, unloading, preparation of surface, ncessary haccking in RCC surface, scaffolding, stagging, providing drip bands, moulds, grooves to any size and shape as shown in drawings tools and plants, fuel, curing, cleaning, consumables etc as complete with all respects complying with relevant standard specification and as directed by the Client / Engineer-in-charge.

Plastering the outer wall surface in cement mortar 1:4 (one cement: four P sand) 12 mm thick in all floor levels .Rate including all materials, labour charges, wastages, necessary lead and lifts, working at all levels, transportaion charges, loading, unloading, preparation of surface, ncessary haccking in RCC surface, scaffolding, stagging, providing drip bands, moulds to any size and shape as shown in drawings tools and plants, fuel, curing, cleaning, consumables etc as complete with all respects complying with relevant standard specification and as directed by the Client / Engineer-in-charge.

Paving the floor with best approved quality fine polished Kota stone slabs of size 600 x 600 of 18 / 20mm with machine cut edges and matching marble slab not less than 100mm width other than Adanga Marbles as border laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three sand) fixing the slabs in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments and polishing with floor polisher to a high degree of finish etc., The kota stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete as per standard speicification officers.

Flooring with Joint free double charged vitrified tiles of approved quality, colour and design joint free of size 600 x 600 x 8mm thick of approved make, quality and colour in all floors over a base layer of cement mortar 1:3 (one cement three sand) 20mm thick and laid straight alignment and pointed neatly with colour cement at the rate of 0.40 kg/m2 laid without any air gap in the tiles neatly and fixing in position as per standard specifications and as directed by the departmental officers. Rate including all materials, labour charges, wastages, necessary lead and lifts, working at all levels, transportaion charges, loading, unloading, the same before handing over as complete with all respects complying with relevant standard specification and as directed by the Client / Engineer-in-charge.( Including Skirting)

Dadooing the wall with ceramic tiles of approved quality, colour and design joint free of size 600x300x10mm thick of approved make, in all floors over a base layer of cement mortar 1:2 (one cement: Two sand) 10mm thick and laid straight alignment and pointed neatly with colour cement at the rate of 0.40 kg/m2 laid without any air gap in the tiles neatly and fixing in position as per standard specifications. Rate including all materials, labour charges, wastages, necessary lead and lifts, working at all levels, transportaion charges, loading, unloading, the same before handing over as complete with all respects complying with relevant standard specification and as directed by the Client / Engineer-in-charge.

Providing Ceramic tiles of size 305 x 305 x 6mm flooring approved make and quality with plain/colour with base mortor in CM 1:3, 10mm thick and pointing with white cement by adding suitable colour pigments including finishing, jointing and polishing with neat finish etc., complete. Rate including all materials, labour charges, wastages, necessary lead and lifts, working at all levels, transportaion charges, loading, unloading, the same before handing over as complete with all respects complying with relevant standard specification and as directed by the Client / Engineer-in-charge.

FOAMED PVC DOOR FRAME Specification: Providing factory made pre-laminated FPVC (Formed Polyvinyl Chloride) Door Frame of the size 105 x 40mm with a wall thickness of 10mm made out of extruded rigid FPVC profile mitre joined with 6 Nos. of 5mm long screw. The door frame shall be fixed to the wall by using 80mm long screws through the frame with the help of PVC fasteners of 3 Nos. to be provided for each vertical member, GI stiffeners of ('U' channel of size 29 x 9, 1mm, 150mm long) - 3 Nos. at hinge point, frame reinforcement of ('U' GI channel of size 46 x 22 x 0.6mm), bottom tie rod of ('U' GI channel size of 15 x 15 x 1mm), etc., complete complying with the standard specification. The door frame should be got approved from the Executive Engineer before use on work Providing of 35mm thick factory made pre-laminated ABS(Acrolynitrile Butadiene Styrene) Door Shutter moulded indifferent designs, consisting of all round frame made out of water proof solid foam PVC bar of size 20 x32mm, reinforcedby 32 x 32mm - 2 Nos., for vertical made out of LVL(Laminated Veneer Lumber), core material of 32mm thickhigh density craft paper honey comb board, sandwiched onboth sides with pre-laminated ABS sheet thickness of 1.5mm.PVC edge banding of size 0.45mm on the vertical sides.Hardware made out of steel coated butterfly hinges - 3 Nos.,for each shutter and ISI make SS round lock complete forfinished item of work, complete complying with the standardspecification. The door shutter and frame should be gotapproved from the Executive Engineer before use on work

Rolling Shutter Manual Operation Supplying and fixing rolling shutters of approved make, made of required size M.S. laths of size 80 x 1.20 mm interlocked together through their entire length and jointed together at the end by end locks mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation to the suitable size and shape as per drawing etc complete including the cost of providing and fixing necessary 27.5 cm long good quality wire springs grade No.2 and M.S. top cover of 1.20 mm thick for rolling shutters. The rate shall be inclusive of one coat of red oxide primer and two coats of synthetic enamel paint of approved quality and colour. Rate including all materials, labour charges, wastages, necessary lead and lifts, transportation charges, loading, unloading, scaffolding, staging, installation charges, fuel, consumables as complete with all respects complying with relevant standard specification and as directed by the Client / Engineer-in-charge.

UPVC Window :Supplying and fixing UPVC (Un-Plasticized PolyvinylChloride) Windows of casement type (open) from the profile the size of outer frame 0mmx58mm and shutter profile are reinforcement with GI/1mm 125GSM and 100% corrosion free, the profiles are multichambered sections with wall thick of 2mm. The EPDMrubber (black colour) covered with over all the edges offrame and shutter the shutter will be provided withEspag multi power point locks and also it operates ashandle. The corners and joints should be welded andcleaned. Radiations free pin headed plain or browncolour glass 4mm thick should be provided to theshutter and it should not allow leakage of water evenat most ranging storms and should have key lockableaction, security protective hinges, strong lockingsystems and as per size for arresting noise and energyloss. The connecting mechanism between sash andouter frame that enables opening of the window. Thewindow should be fixed to the wall with 100% packingwith screws and silicon packing all round the frames.The window should be got approved from the Executive Engineer before use on work (SOR item No:

UPVC Ventilator Specification: Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved from the Executive Engineer before use on wor

Providing and fixing welded M.S. grills to the window openings,along the details as per drawing with necessary screws, bolts and fixed with necessary M.S. lugs embedded in masonry with C.C. 1:2:4 and finishing the surface neatly. Rate shall welding and consumables, etc. complete, as directed. Design of grills and the size of members to be used shall be got approval before put into use & as directed by the Client / Engineer-in-charge.

Painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over the existing red oxide priming coat in all floors including cost of priming coat etc., complete complying with standard specification. ( The make quality and colour of paint should be got approved by the executive Engineer before use on works.)

Supply and painting of two coats of Acrylic emulsion paint of approved shade and colour over one coat of DCP Primer including one coat of Acrylic Wall Putty with DCP Primer. Rate including all brush, roller, ladder, scrapping, washing, materials, labour charges, wastages , cleaning, necessary lead and lifts, scaffolding, stagging, working at all levels, elevations, transportaion charges, loading, unloading, curing, sanding, touchup putty, surface thoroughly cleaned and wetted before painting as complete with all respects complying with relevant standard specification and as directed by the Client / Engineer-in-charge.(Internal surface)

Supplying and painting of 2 coats of weather proof exterior emulsion with high sheen, anti algal properties over one coat wall exterior primer of approved quality and shade etc., complete. Rate including all brush, ladder, scrapping, washing, materials, labour charges, wastages , cleaning, necessary lead and lifts, scaffolding, stagging, working at all levels, elevations, transportaion charges, loading, unloading, curing, sanding, touchup putty, surface thoroughly cleaned and wetted before painting as complete with all respects complying with relevant standard specification and as directed by the Engineer-in-charge.

Paving with Rubber Moulded hydraulically pressed cement concrete paver block with pattern design of 50% colour and 50% Plain of 83 mm of approved quality and colour, over the sand filling to full depth of slab perfectly and neat finishing the joints, compressing with vibrator. The rate shall be inclusive of cost of paver block, taxes, incidental charges, transportion charges and labour charges for fixing, neat finishing the joints as directed by the departmental officers etc., complete complying with standard specification. The paver block should got approved by the departmental officers before use on work.

Providing guildeline road marking kerb painting (special acrylic medium pigmented ) involving cleaning the surface free of dirt and loose particles applying one coat of primer and applying one layer of 20 to 25 microns. Rate shall include for all materials & labour components etc., as complete all respects complying with relevant IRC specifications, as directed by the Client / Engineer-in-charge.

Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick at required locations to a height of 900mm from finished floor level welded to 38mm dia Stainless Steel pipe post of 1.00mm thick as vertical at 900mm centre with 2 Nos. of 25mm dia intermediate horizontal stainless steel pipe of 1.60mm thick in between. The vertical pipe has to be welded to the 100 X 100 X 6mm MS base plate encased in the base concrete. The rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, conveyance, electrical charges, etc. complete

Weathering course-using broken brick jelly 20 mm gauge in pure slacked lime (No sand to be used) over RCC roof slab. The proportion of broken brick jelly to slaked lime being 32:12½ cft well beaten by wooden beaters for giving required slope. Rate including all materials, labour charges, wastages, necessary lead and lifts, transportation charges, loading, unloading, with all respects complying with relevant standard specification and as directed by the Client / Engineer-in-charge.

Finishing the top of roof with one course of machine pressed tiles of size 23x23x2cm of approved quality laid in CM 1:3 (one cement and three sand) mixed with 2% of water proofing compound by weight of cement used and pointed with the same oiled mortar including mixing of red oxide etc ., Rate including all materials, labour charges, wastages, necessary lead and lifts, transportation charges, loading, unloading, with all respects complying with relevant standard specification and as directed by the Client / Engineer-in-charge.

Fixed Glass Doors - frameless patch fitting door consisting of 12mm clear toughened glass ( Saint gobain/ Modi make) and fixing with Dorma/Ozone make floor spring, top patch, pivot, bottom patch, corner lock, H type handle ( standard) & etc. all the necessary fittings & all complete as shown in attached drawing and as per the direction of Engineer-in-charge

Supply, fabrication and erection of Structural Steel members for installation of Steel Truss including enamel painting complete and the same shall comply to All primary steel member such as column and rafter conform to grade E-350 as per is 2062. All cold form steel members such as purlin shall conform to grade E-350 as per is 811. Steel members such as bracings, angles, conform to grade E-250 as per is 2062. All secondary structural steel plates such as base plates, end plates, shall conform to grade E-350 (FE 490) as per is 2062.

Supply & installation of precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm +/- 5% total coated thickness (TCT) thick Zinc coating 120gsm as per IS: 277 in 240mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15- 18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches while transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55mm) with EPDM seal or with polymer coated J or L hooks, bolts and nuts 8mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead complete upto any pitch in horizontal/ vertical or curved surfaces excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Structural Glazing: Providing and fixing structural glazing fabricated from roll formed sections made of galvanized steel colour coated (Base steel as per IS 513 of ‘D’ quality, galvanized as per IS 277 with Zinc of 120 grams / sqm.) with total coated thickness of 0.72mm. The glass holding section made of 304 grade SS of 0.6mm thick. Galvanized steel sections are to be used as stiffeners inside the colour coated steel / powder coated sections as per the design requirement. Design calculations are made to suit wind pressures as given in IS Paint specifications: Primer coat with epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16microns thick and back coated with alkyd backer of 5-7 microns or powder coated with pure polyester powder upto50-60 microns thick. Dimensions: The section should be of 37 x 53mm for frame vertical, 37 x 53mm for frame horizontal section and section for reinforcement should be of 31 x 55mm. glass holding section should be of 37 x 37mm for top and bottom grids in between should be of 37 x 18mm. Accessories: Brackets made of CRCA powder coated / electro plated should be used to fix vertical at top and bottom and vertical to slab as per site requirement. Polyurethane brackets should be used to connect horizontal section to vertical sections. Silicone: Natural cure, with good UV resistance to be used. The above frame should be fixed to brick / concrete masonry by using nylon self–expanding cap and driving MS electro plated 80mm long screws into the caps through frames. Glass: 5mm reflective Saint Gobain OR equivalent.

Providing and laying water proofing treatment to vertical and surfaces for sunken portion of depressed portions of W.C., and the like consisting of :i) Ist course of applying cement slurry @ 4.4 Kg/sqm mixed with water proofing compound conforming to IS 2645 in recommended proportions including rounding off junction of vertical and horizontalsurface. ii) IInd course of 20mm cement plaster 1:2 (1 cement : 2 coarse sand)mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface.iii) IIIrd course of applying blown or residual bitumen applied hot at 1.7Kg. per sqm of area. iv) IVth course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 Kg/sqm.)

PLUMBING WORKS

Supplying & fixing in position 15 mm dia brass/ C.P screw down tape (Heavy duty) of approved make conforming to I.S. Specifications & quality including cost of shellac, thread etc., complying with standard specifications & including cutting & threading wherever necessary. (Taps should be got approved by the Executive Engineer before use on the work).

C.P Tap

Constructing brick masonry manhole with second sort ground moulded (Chamber burnt) bricks in CM 1:5 (one of cement, fivr of sand) including earthwork excavation and sand filling for a depth of 150mm top cover slab with CC 1:2:4 (one of cement, two of sand, four of graded aggregate) 20mm nominal size for fixing C.I Frame, including shuttering, reinforcement foundation concrete 1:4:8 (one of cement, four of sand, eight of graded aggregate 40mm nominal size) 100mm tk., plastering inner, outer and other exposed surface with 15mm tk., cement mortar 1:3 (one of cement, three of sand) and finishing with a floating coat of neat cement with water proofing compound as per specification, making channelsin CC 1:2:4 (one of cement, two of sand, four of graded aggregate) neatly finished including fixing C.I. Cover and frame, C.I. Rungs etc., complete complying to standard specification.

Manhole 600 x 600 mm internal size

Manhole 900x900x1000-1400 mm Size

Supplying and fixing in position the best quality and variety sizes PVC Soil/ Waste /Rain water pipes 6Kg / cm2 of ISI mark, providing leak proof joints etc and making connection to all sanitary fittings, including dismantling masonry / RCC works wherever necessary and making good the dismantled portions to the original condition complying with standard specification.(Internal,External&Rain water system)

200mm Dia

160mm Dia

110mm Dia

75mm Dia

Supplying & fixing in position PVC Nahini trap /Floor trap of various sizes with best Stainless Steel gratings of approved brand & quality, fixed over a bed of brick jelly lime concrete 1:2:5 ( One part of lime, two parts of sand & five parts of 40 mm size brick jelly ) & finished with cement mortar 1:3 ( One cement & three sand ) including dismantling masonry works wherever found necessary & making good the damaged portions to the original condition & giving connections to the cast iron pipes as directed etc., complete, complying with standard specification (The C.I.Nahini trap should be got approved by the Executive Engineer before use on works ).

Supplying & fixing in position 150 X 100 mm square mouth 'P' or 'S' trap stone ware Gully trap 'A' grade with cast iron gratings of size 300 X 300 mm with C.I. air tight cover with frames of size 300 X 300 mm at bottom & top respectively with necessary earth work excavation, laid over a bed of brick jelly cement concrete 1:3:6, 150 mm thick using 20 mm size broken brick jelly including necessary brick work & plastering, &including dismantling masonry wherever necessary & redoing the damaged portions to the original condition & by using cement concrete 1:3:6 using 20 mm stone jelly for fixing the Gully trap & giving connections to the stone ware sewer line etc., complete, complying with standard specification. (The stone ware gully trap should be got approved by the Executive Engineer before use on works ).

Supplying and fixing of indian make white glazed earthern ware flat back urinal of ISI make of (HxWxP :44cm x 31.5cm x 26.5cm) provided with inlet connection using 15mm flexible PVC connection house of suitable length, 15mm CP push cock and 32mm bell mouthed PVC connection waste pipe etc., fixing to the wall in position with necessary teak wood plugs, clamps, screws etc., Rate inclusive for cost of materials labour and transport charges etc., complete (the urinal anf fittings should be got apprioved by the Engineer - In- charge before use on work.

Wash Hand Basin of size 550 mm X 400 mm with all accessories such as cast Iron Brackets, 32 mm Dia C.P. Waste coupling, Rubber plug and Chain, 32 mm dia ' B ' Class G.I. Waste pipe, 15 mm Dia G,M Wheel valve; 15 mm Dia Nylon connection, 15 mm Dia Brass Nipples, 15 mm C.P. Pillar tap etc.,

Supply and fixing in position white European Water Closet of approved make with low level flushing tank 10 litre capacity of best quality and approved make with 100mm P or S trapwith double flapped rigid PVC seat cover with CP brass hinges etc. complete complying with standard specification and as directed by the Departmental officers (The EWC should be got approved by the Executive Engineer before use on works.

Supplying, laying and jointing UPVC pipes of approved quality and best variety conforming to ISS and with ISI mark of the following size including cutting, threading and fixing PVC specials but excluding cost of such specials and fixing to wall with necessary teak wood plugs, PVC clamps and screws, making good the dismantled portions to original condition with necesscary brick work and plastering wherever necessary scaffolding charges above ground level upto 4 m height. (Internal,Terrace&External Water supply )

20 mm Dia Upvc Pipe

25 mm Dia Upvc Pipe

32 mm Dia Upvc Pipe

40 mm Dia Upvc Pipe

50 mm Dia Upvc Pipe

Supplying & fixing in position first quality & approved variety of various dia U.P.V.C Ball Valves ( Heavy type ) with I.S.I. Mark of the following size including cost of Shellac, thread etc.,including labour for cutting & threading of Pipes etc., complete complying with standard specifications for both internal & external water supply arrangements.

40mm Dia

50mm dia

Supply ,erection and testing & commisioning of 2HP submersible pumpset of capacity of 2 LPS @ 35M, head pumps fitted with bronze impellers and having delivery size of 40mm - 430V along with 3mts cable and manufactures standard control panel which is mandatory and as directed by the officer incharge and other required supporting items like SS hose nipple, nylon rope, clamps, bolt and nuts,GI nipple, completed and as directed by the officer incharge. (DWS OHT Transfer pump-1W&1S)

UG Sump&Over Head Tank Cover

Manhole Cover Size 600x600 mm Manhole Cover With Frame 5 Ton - Double Cover

Providing and keeping in stores, shifting to the place of installation, fixing of 1mtr length, 6mm Thickness MS Puddle flange UG Tank & OHT Puddle flage

50mm MS Puddle Flange

40mm MS Puddle Flange

ELECTRICAL WORKS

Wiring, testing and commissioning of 2Rx1.5sqmm (22/0.3) +1Rx1sqmm PVC insulated unsheathed SC Cu. Conductor of 1100V grade in suitable PVC rigid pipe with 2 mm thick, ISI marked concealed in wall and ceiling with PVC accessories with concealed type manufacturer's GI metal back box and 6A modular switch in flush with wall mounted on poly carbonate front plate with switch mounting metal parts, for making good of the concealed portion with suitable colour for PVC concealed point (Primary)

Wiring, testing and commissioning of 2Rx1.5 +1Rx1sqmm (22/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100V grade in suitable PVC rigid pipe with 2 mm thick, ISI marked concealed in ceiling with PVC accessories for additional light (Secondary)

Wiring, testing and commissioning of 3R x 1.5sqmm (22/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100V grade in suitable PVC rigid pipe with 2 mm thick, ISI marked concealed in wall and ceiling with PVC accessories in flush with wall with manufacturers GI metal back box and 6A modular two way switch in flush with wall mounted on poly carbonate front plate with switch mounting metal parts, (Two way) and making good of the concealed portion with suitable colour for concealed staircase light point.

Wiring, testing and commissioning of 2Rx1.5sqmm (22/0.3) PVC insulated unsheathed SC Cu. Conductor of 1100V grade in suitable PVC rigid pipe with 2 mm thick, ISI marked concealed in wall and ceiling with PVC accessories with concealed type manufacturer's GI metal back box and 6A modular switch & 2 module Fan Requlator in flush with wall mounted on poly carbonate front plate with switch mounting metal parts, for making good of the concealed portion with suitable colour for PVC concealed point (Fan poinr)

Lift Shaft Wiring : Wiring, Connecting, Testing & Commissioning for lift well light point and 6Amps power socket outlet with 2 x 2.5 sqmm FRLS PVC insulated stranded copper conductor of 1100V grade along with 1 x 2.5 sqmm FRLS PVC insulated standed copper conductor cable as earth wire in MS conduit including providing and fixing switch box, 2 Nos. of 5A single way module switch (for controlling light point and socket Outlet ) for each floor of the lift well , with bulkhead lamp 1 No. 5A 5 Pin shuttered socket outlet with flush type switch for each floor of the lift well and making necessary connections complete etc.

Supply and fixing of manufacturer's GI metal back box and 6A modular switch, 6A 3 pin and 2pin combined modular type wall socket in flush with wall mounted on poly carbonate front plate with switch mounting metal parts, in flush with wall.

Supply and fixing of manufacturer's GI metal back box and 16A modular switch, 6/16A 3 pin combined modular type wall socket in flush with wall mounted on poly carbonate front plate with switch mounting metal parts, in flush with wall.

Supply and fixing of manufacturer's GI metal back box and 2nos 6A modular switch, 2nos of 6A 3 pin combined modular type wall socket in flush with wall mounted on poly carbonate front plate with switch mounting metal parts, in flush with wall.

Supply and fixing of manufacturer's GI metal back box and 16A modular switch,& socket 2nos of 6A 3 pin combined modular type wall socket with switch in flush with wall mounted on poly carbonate front plate with switch mounting metal parts, in flush with wall.

Supply and Fixing of 20 A DP plug and socket in sheet enclosure with 32A DP MCB in Flush with wall with Earth Connection ( For AC Plug)

Supply, run, testing and commissioning of 2Run 2.5 sqmm and 1R of 1.5 sqmm (22/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100V Grade in suitable PVC rigid pipe with 2 mm thick, ISI marked on wall and ceiling with continuous earth wire connection with painting of suitable colour.

Supply, run, testing and commissioning of 2 of 4sqmm (56/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100V Grade in suitable PVC rigid pipe with 2 mm thick, ISI marked concealed in wall and ceiling with continuous earth wire connection of 2.5 sq.mm wire PVC insulated SC unsheathed Cu.Conductor of 1100V Grade and making good of the concealed portion with suitable colour (for Bus bay fitting, 15 Amps socket, 20 Amps AC socket)

Supplying, installation, testing and commissioning of 32 AMPS TPN industrial plug & socket for e vechicle charging with 32 Amps 4P MCB in Manufactures box fixed flush with the wall including cost of material, necessary interconnection etc, with earthing etc., all complete and as directed by the departmental officers.,

Supplying, installation, testing and commissioning of 1200 mm (48") sweep AC ceiling fan complete with modular type stepped electronic 300W regulator, with 1 metre down rod with all required accessories.including point wiring

Supplying, installation, testing and commissioning of 375 mm (15") sweep (heavy duty) AC exhaust fan complete without provision of holes in the wall including all required accessories.

Supply and fixing of double door type 8 way triple pole & neutral industrial MCB board with IP 42 Protection 7segment MCB distribution board in sheet steel enclosure with 63A 4 pole MCB isolator as incoming and 24 Nos. 6 A to 32 A SP MCB as outgoing in flush with wall and making good of the concealed portion with earth connection. The MCB DB and MCB's should be with the ISI mark etc., all Complete, complying with relevant standard specification and as directed by the Departmental Officers.

Supply and fixing of double door type 4 way triple pole & neutral industrial MCB board with IP 42 Protection 7segment MCB distribution board in sheet steel enclosure with 40A 4 pole MCB isolator as incoming and 12 Nos. 6 A to 32 A SP MCB as outgoing in flush with wall and making good of the concealed portion with earth connection. The MCB DB and MCB's should be with the ISI mark etc., all Complete, complying with relevant standard specification and as directed by the Departmental Officers.

Supply and fixing VERTICAL THREE PHASE SHEET STEEL DISTRIBUTION BOARD WITH MCB 8 way per phase, flush type fitted with bus bars and neutral links with 8 numbers of 32 Amps triple pole MCB, one number of Four Pole 63 Amps MCCB/Isolator with ISI mark etc., all Complete, complying with relevant standard specification and as directed by the Departmental Officers. with IP 42 Protection.

Supply and fixing VERTICAL THREE PHASE MCCB DISTRIBUTION BOARD WITH MCB 8 way per phase, flush type fitted with bus bars and neutral links with 4 numbers of 20/32 Amps & 4nos of 40A triple pole MCB, one number of Four Pole 100 Amps MCCB/Isolator with ISI mark etc., all Complete, complying with relevant standard specification and as directed by the Departmental Officers. with IP 42 Protection.

Supply and fixing of double door type 12way SPN MCB board with IP 42 Protection with 40A 4 pole MCB isolator as incoming and 6Nos. 6 A to 32 A SP MCB as outgoing in flush with wall and making good of the concealed portion with earth connection. The MCB DB and MCB's should be with the ISI mark etc., all Complete, complying with relevant standard specification and as directed by the Departmental Officers. (LIFTDB)

Supply and fixing of double door type 12way SPN MCB board with IP 42 Protection with 20A 2 pole MCB isolator as incoming and 6Nos. 6 A to 32 A SP MCB as outgoing in flush with wall and making good of the concealed portion with earth connection. The MCB DB and MCB's should be with the ISI mark etc., all Complete, complying with relevant standard specification and as directed by the Departmental Officers. (ELDB)

Supply, installation, testing and commissioning of 63/40A 4Pole MCB in suitable enclosure

Supply, installation, testing and commissioning of 20 W LED tube light fitting with cool day light made out of CRCA powder coated body, poly methyl meth acrylate (PMMA) diffuser, glare free light, Suitable for recessed / surface mounting including electronic drivers, day light colour LED lamps, inter connecting wiring including accessories all inclusive.

Supply, installation, testing and commissioning of 18 W LED DOWN LIGHT FITTING with IP55 cool day light suitable for pole mounting, made out CRCA powder coated body, aluminium reflectors, poly methyl meth acrylate (PMMA) diffuser, glare free light, including electronic drivers, day light colour LED lamps, inter connecting wiring with suitable fixing clams, hooks as required including accessories all inclusive.

Supply, installation, testing and commissioning of 36 W LED 2X2 light fitting with cool day light, made out of CRCA powder coated body, aluminium reflectors, poly methyl meth acrylate (PMMA) diffuser, glare free light, suitable for recessed / surface mounting including electronic drivers, day light colour LED lamps, inter connecting wiring including accessories all inclusive.

Supply, installation, testing and commissioning of 2x22 W LINEAR LED light fitting with cool day light, made out of CRCA powder coated body, aluminium reflectors, poly methyl meth acrylate (PMMA) diffuser, glare free light, suitable for recessed / surface mounting including electronic drivers, day light colour LED lamps, inter connecting wiring including accessories all inclusive.

Supply, installation, testing and commissioning of 48 W midbay LED fitting with cool day light suitable for surface / recessed mounting, made out of CRCA powder coated body, aluminium reflectors, poly methyl meth acrylate (PMMA) diffuser, glare free light, Suitable for pendent mounting including electronic drivers, day light colour LED lamps, inter connecting wiring including accessories all inclusive.

Supply, installation, testing and commissioning of 250 W LED FLOOD LIGHT FITTING with cool day light suitable for surface / recessed mounting, made out CRCA powder coated body, aluminium reflectors, poly methyl meth acrylate (PMMA) diffuser, glare free light, including electronic drivers, day light colour LED lamps, inter connecting wiring with suitable fixing clams, hooks as required including accessories all inclusive.

Supply, installation, testing and commissioning of 120 W LED STREET LIGHT FITTING with IP65 cool day light suitable for pole mounting, made out CRCA powder coated body, aluminium reflectors, poly methyl meth acrylate (PMMA) diffuser, glare free light, including electronic drivers, day light colour LED lamps, inter connecting wiring with suitable fixing clams, hooks as required including accessories all inclusive.

Supply, installation, testing and commissioning of 80 W LED STREET LIGHT FITTING with IP65 cool day light suitable for pole mounting, made out CRCA powder coated body, aluminium reflectors, poly methyl meth acrylate (PMMA) diffuser, glare free light, including electronic drivers, day light colour LED lamps, inter connecting wiring with suitable fixing clams, hooks as required including accessories all inclusive.

Supply, installation, testing and commissioning of 28W LINEAR LED light fitting with cool day light, made out of CRCA powder coated body, aluminium reflectors, poly methyl meth acrylate (PMMA) diffuser, glare free light, suitable for recessed / surface mounting including electronic drivers, day light colour LED lamps, inter connecting wiring including accessories all inclusive. (COST CONSIDERED EQ TO 36W 2X2)

Supply and laying of following XLPE armoured LTUG cable in a trench/Tray with suitable cable tie tag etc as required.

3.5CX185sqmm Al.armoured LTUG Cable

3.5CX120sqmm Al.armoured LTUG Cable

3.5CX50sqmm Al. armoured LTUG Cable

3.5CX25sqmm Al. armoured LTUG Cable

4CX16sqmm Al.armoured LTUG Cable

4CX10sqmm Al. armoured LTUG Cable

4CX16sqmm Cu. armoured LTUG Cable

4CX6sqmm Cu. armoured LTUG Cable

3CX6sqmm Cu. armoured LTUG Cable

4CX4sqmm Cu. armoured LTUG Cable

3CX2.5sqmm Cu. armoured LTUG Cable

1CX16sqmm Cu. unarmoured LT Cable

Supply and fixing of double compression brass cable gland for following Aluminium conductor XLPE insulated armoured cable of 1100 V grade with earth connection.

3.5CX185sqmm Al.armoured LTUG Cable

3.5CX120sqmm Al.armoured LTUG Cable

3.5CX50sqmm Al. armoured LTUG Cable

4CX25sqmm Al. armoured LTUG Cable

4CX16sqmm Al.armoured LTUG Cable

4CX10sqmm Al. armoured LTUG Cable

4CX16sqmm Cu. armoured LTUG Cable

4CX6sqmm Cu. armoured LTUG Cable

3CX6sqmm Cu. armoured LTUG Cable

4CX4sqmm Cu. armoured LTUG Cable

3CX2.5sqmm Cu. armoured LTUG Cable

1CX16sqmm Cu. unarmoured LTUG Cable

Supply and installation of following size of GI Ladder / preforated cable tray including pre fabricated horizontal and vertical bends, reduces, tees, cross members with 300 mm spacing and other accessories as required and duly suspended from the ceiling, wall with MS angles, channels, suspenders, including painting, anchor fasteners, civil works etc., as required as per specification.

450X50mm Perforated Tray

300X50mm Perforated Tray

150X50mm Perforated Tray

Supply and insallation maintenance free GI Earthing System comprising of 50mm dia and 2 mtr. long earth electrode of low carbon steel rod with 100 micron bonding and 25 kgs. of carbon based environment friendly backfill compound and suitable clamp

Supply, Installation, Testing and Commissioning of earthing station consisting of 600 x 600 x 3 mm. thick, copper Plate earth electrode, back filling with alternate layer of charcoal, salt, brick masonry work for chamber 450 x 450 mm. heavy duty CI cover, watering pipe, funnel and earthing conductor as per IS:3043 specification. All civil works required such as excavation in all types of soils, rocks, PCC Earthing Chamber foundation, reinstatement and making good the surface to match original, removal of surplus earth etc. are included.

Supply, fabrication, of GI /Copper earth flat of following size in provided trench, clamping in wall, ceiling, with suitable Clamps/ saddles, connecting the joints through bracing / welding covering with bitumen paint including accessories wooden plugs, screws, fastener etc., all inclusive

25mm x 6mm GI Flat

25mm x 3mm GI Flat

25mm x 6mm copper Flat

25mm x 3mm copper Flat

No8 SWG copper

CT Metering Panel - Supply, Installation, Testing and Commissioning of CPRI approved make of panel, cubicle type, Free standing, floor mounted, single front, 14 SWG CRCA sheet steel, enclosed separate compartment for each feeder, front operated, Powder coated, indoor type dust and vermin proof, hinged lockable doors, complete with electrolytic grade copper bus bars, internal wiring, colour coding, ferrules, Panel mounting MS Channels, fasteners, etc., including all associated control wiring. 1set of 200/5A CT with TNEB Metering provision and 1nos of 200/5A CT for APFCR

250A Isolator Panel - Supply, Installation, Testing and Commissioning of CPRI approved make of 250A TPN MCCB panel, cubicle type, Free standing, floor mounted, single front, 14 SWG CRCA sheet steel, enclosed separate compartment for each feeder, front operated, Powder coated, indoor type dust and vermin proof, hinged lockable doors,

Supply, erection, testing, commissioning of 160KVA DG Set With Diesel Engine developing suitable HP at 1500 RPM, 4 Cycle, 12 cylinder, water cooled, turbo charged, complete with standard Accessories confirming to latest emission control latest norms coupled to alternator rated at 160 KVA, 3 phase, 4 wire, 0.8PF (lag), 415V, IP 21 enclosure, class F/H insulation, with AVR, mounted on a channel iron base frame with foot mounting AVM pads, confirming to IS 4722, 1day capacity Litters fuel tank, 2x12V 120 AH battery with leads, AMF panel, Hospital type Silencer, with acoustic enclosure, control panel, inter connecting control cable, cable end termination, including necessary fuel tank system, lubrication system, cooling system, fabrication of exhaust M.S pipe system, supporting frame, structures arrangement, confirming to CPCB norms etc., all inclusive. The cost will include all statutory approval govt authorities.

Supply, Installation of 10KVA 3P/3Pconventional type UPS with 15min battery backup with necessary interconnection cables, breakers, MS stand etc as required

Supply, Installation of 3KVA conventional type UPS with 30min battery backup with necessary interconnection cables, breakers, MS stand etc as required

Supply, Erection of 8m Free Standing Single Arm Bracket 8 sided Octogonally continously tapered structured pole with base plate of size 300 x 300 x 12mm as per IS-875 with following specification. Bottom Pole Dia - 130mm Top Pole Dia - 70 mm Thickness of Pole - 3 mm The pole should be hot dip galvanized confirming to BESN ISO- 1461 with thickness of 65 Micron - The pole is 9mtr height instead of 8mtr and single instead of double arm

2m x 1m Rubber Mat suitable for 11 KV installation confirming to IS

First Aid Box complete with all First Aid Medicines

Shock Treatment Chart fixed in glass frame

Danger Board as required by the Electrical Authorities

Fire Extinguisher Co2, 4.5 kg. confirming to TAC Norms

TNEB coordination charges getting load sanction and necessary documentation works upto power avail to the site (CT Service connection)

Supply, Installation, Testing and commissioning of 32 channel 8 SATA NVR, with 6T Hard Disk Drive 4 nos, New logical and visualized GUI design Dual-OS design to ensure high reliability of system running, ANR technology to enhance the storage reliability when the network is disconnected, Configurable normal or hot spare working mode to constitute an N+1 hot spare system Video Input and Transmission, Connectable to the third-party network cameras Compression and Recording, H.265+ compression effectively reduces the storage space by upto 75%, Full channel recording at up to 12MP resolution HD Video Output  HDMI1 / VGA1 outputs provided  HDMI1 Video output at up to 4K ( 3840 × 2160 ) resolution Storage and Playback, Upto 16 SATA interfaces and 1 eSATA interface for HDD connection, Support upto 10TB capacity for each HDD, Smart search for efficient playback.

Supply of 8MP, Internet Protocol fixed BULLET CAMERA with following specification: ●1/2.5" Progressive Scan CMOS, ● 3840 × 2160 @15 fps,2.8/4 mm fixed lens,01 lux @ (F1.2, AGC ON), 0.028 lux @(F2.0, AGC ON), 0 lux with IR, H.265+, H.265, H.264+, H.264, 2 Behavior analyses ( Line crossing detection, intrusion detection) ● Face Detection ● 120dB WDR, ● BLC/3D DNR/ROI, IP67 complied ●On-board Storage - Built-in micro SD/SDHC/SDXC card slot, up to 128 GB, ● Shutter Speed 1/3 s to 1/100,000 s, ● 3-Axis Adjustment Pan: 0° to 360°, tilt: 0° to 100°, ● rotate: 0° to 360°, 2.8 mm, ● horizontal FOV: 102°, vertical FOV: 53°, diagonal FOV: 124°, ●Lens Mount M12 ● IR Range I5: up to 50 m, ● Image Settings Rotate mode, saturation, brightness, contrast, sharpness adjustable by client software or web browser, ● Power Consumption and Current-12 VDC, 0.7 A, max. 7.5W PoE: (802.3af, 36V to 57V), 0.3 A to 0.2 A, max. 9W ● Camera out fitted with metal housing so as to prevent the lens from damages during physical abuse. (Make: Dahua/Panasonic)

Supply, Installation, Testing and Commissioning of 55" smart LED TV with following specifications a) Full HD 1920 x1080 (4K monitor) b) IPS pannel c) Slim back light LED module d) 900 PMI e) Triple XD engine f) Dynamic scanning g) ANR h) True colour generator i) 8modes of picture j) picture wizardIII k) Real cinema 24P l) HDMI -3nos m) USB -3nos n) Built in LAN o) Magic remote p) Dimension 1242 x 724 x 55.1min(37). (Make: Sony/ LG /Samsung).

Supply and OFC patch of OFC Single mode Media Convertor with configaration charges etc.,

Supply and fixing of outdoor 4X6 PVC box with 102mm x 77mm x 102mm with all fixing accessories.

Supply and Clamping of CAT 6 armoured cable in suitable PVC Pipe 1" thick on wall / ceiling with connected PVC accessories with clamps, saddles etc., complete. (Between ethernet switch to camera and radio modem) i. Application : Primary (Campus), Secondary (Riser), Tertiary(Horizontal) IEEE 802.3 : 10Base-T; 100Base-T; 1000Base-T IEEE 802.5 16 MB; ISDN; TPDDI; ATM ii. Standards: ISO/IEC 11801 2nd ed.; IEC 61156-5 2nd EN 50173-1; EN 50288-6-1,EIA/TIA 568C.2, RoHS Compliant. Fire Rating: PVC : IEC 60332-1. iii. Conductor - Bare Copper Wire iv. Insulation - Polyethylene v. Twisting - 2 Cores to the pair vi. Cable lay up - 4 Core to the pair It has diameter of (23 AWG) 0.550 ± 0.015.Insulation : Polyethylene.GI wire of size is 0.90 ± 0.030mm.

Fixing and Termination of CAT 6 Cable RJ 45Jack Single Point ( Point to Point ) Crimping, Testing and arrangement charges.

Supply and fixing of 3nos 6A, 5 pin socket controlled by 3 nos 6A switch, modular type in suitable size Modular plate and enclosed in a 9 Module Manufacturer's Box complete with interconnections and earthing rate should include all the necessary labour charges to complete the work for NVRs and Monitors.

Supply and run of 2 x 1.5Sq.mm PVC and SC unsheathed copper cable of 1100v grade in suitable PVC pipe in wall and Ceiling with connected PVC accessories with continuous earth connection of 1 of 1.0Sq.mm copper cable.

Supply and laying of armoured, Singlemode, Thermoplastic Tape Inner Sheathed, PVC type sheathed 6 core Optical Fibre Cable with unique fiber excess length control method provides the cable with excellent mechanical and environmental properties and Cable - 2 Embedded FRP provides tensile strength & Anti-buckling properties. It is processed with Filling jelly - Thixotropic jelly to prevent Water ingress in loose tube.

Fixing and Termination of Optical Fibre Cable Single Point ( Point to Point ) Splicing and arrangement charges.

Supply and fixing of 24 Port 2SFP with Module, PoE Giga Range Lan Switch.• 24 Ports 10/100/1000 Base-T PoE + 4 x Combo Gigabit UTP or Gigabit SFP slots • Support IEEE 802.3af (PoE) and 802.3at (PoE+) Standard • Equipped with IEEE 802.3az Energy Efficient Ethernet (EEE) Complaint • Support IEEE 802.1Q VLAN traffic segregation • Access Control List (ACL) feature to enhances network security • Auto Surveillance VLAN for easy integration with IP-based surveillance systems • Loopback detection (LBD) and broadcast storm control to avoid network downtime • Quality of Service (QOS) and bandwidth control to ensure smooth operation • Support Web-based GUI, Smart Console , Network Assistance Utility • Cable diagnostics function to help troubleshooting wiring problem including Optical Fiber Cable connecting network accessories. (Make: DLINK, NETGEAR,TPLINK)

Supply and fixing of POE 8 port switch 10/ 100 / 1000 Base -T / 2 x 1000Base-FX / 20Gbps bandwidth / IEEE803.af/at compliant PoE+ / RJ45 supports auto MDI/MDI-X function / Auto negotiation speed, half/full-duplex / Store and forward / Max packet size: 10kbytes / Wide range power design (12~56VDC) / Operating temperature (-40 ̊C ~ +75 ̊C) / Reverse polarity protection / Resettable fuse to protect against overcurrent / IP-40 protection / EFT protection for power line. (Make: DLINK,NETGEAR/ TPLINK)

Supply and fixing of OFC PVC Black Colour Box 1'x 3/4' x2

Supply and fixing of Rack with Accessories- Higher end 42 U Rack with LIU Unit and fan extra for the above Rack

PA SYSTEM

Supply and Installation of 480 watts Installation P.A Amplifier Specification:- 1. Power Output : 480W Max., 480W RMS at 10% THD, 550W RMS at 5% THD, 500W RMS at 2% THD, 480W RMS at 1% THD 2. Output Regulation:≤ 2 dB, no load to full load at 1kHz 3. Input Channels:1 × 200mV/470kΩ (unbal.), 2 × 1V/50kΩ (bal.), 1 × 100V Input/50kΩ 4. Frequency Response : 50-15,000Hz ±3dB 5. Signal to Noise Ratio:60dB 6. Tone Controls:Bass: ±10dB at 100Hz, Treble: ±10dB at 10kHz 7. Outputs:Loop through 1 × 200mV/480W, 2 ×1V/1kW 8. Speaker Outputs:4Ω, 8Ω, 70V & 100V 9. Power Supply:DC: 24V (2×12V Car Battery) AC: 220-240V 50/60Hz 10. Power Consumption: DC: 15A AC: 1200VA (Make: Ahuja, Bose, Yamaha or equivalent)

Supply and Installation of 15 watts indoor Wall Speaker with Line Matching Transformer in the existing pole with supporting clamp Model:- Specification:- 1.Input Power : 15W RMS/20W Max 3. Frequency : 250-10,000Hz 4. SPL : 108dB/1W/1m,122dB/25W/1m at 1kHz 5. Power Taps : 40/30/20/10/5W (Make: Ahuja, Bose, Yamaha or equivalent)

Supply and Installation of 120 watts P.A Mixer Amplifier Model: SSB60 Specification:- 1.Frequency Response : 50-15000Hz ±3db 2. Signal to Noise Ratio:60db 3.Tone Controls : Bass;-10db at 100Hz 4. Treble: 10db at 10KHz. 5. Speaker Outputs :4Ω,8Ω,16Ω &100V (Make: Ahuja, Bose, Yamaha or equivalent)

Supply and Laying of 2CX1.5Sq.mm Speaker PVC flexible cable and wherever neccesary the rate is inclusive of all material etc.,

Supply & Installation of goostneck paging Dynamic microphone 1. Switching Signal Level:100V (Nominal) 2. Controls : Mic Level, Chime level, Alarm level 3. Power Supply:AC 220-240V, 50/60Hz; DC 24V (2 x 12V Car Battery) 4. Dimensions: W483 × H75 × D300 5. Weight: 4.8kg

Interconnecting testing and commissioning of the PA System

Supplying, erecting, testing and commissioning of machine room less passenger Elevator having 8 passengers capacity, rated speed 1.0 mtr. / sec., for GF & 1st floor, 400 volt 3 phase, 50 Hz, AC variable voltage variable frequency derive with speed encoding, simplex full collective with / with out attendant, microprocessor based controller located top floor, variable frequency regenerative drive, flat polyurethane coated belts for traction media, stainless steel panels with hairline finish for car and door, gearless with permanent magnet motor located in the shaft top, all openings are located at the front of the hoist way, with centre opening Automatic with ACVVVF door operator with electronic door protective system, stainless steel hairline finish sliding doors, painted frame with down light false ceiling, Stainless Steel mirror finish hand rails, granite flooring of client choice, sixteen segment digital LED display position indicator in all floors, digital car position indicator, over load warning indicator, battery operated alarm bell and emergency light, fireman's switch at main lobby, with automatic rescue device, intercom between lift car and lobby and controller, voice synthesizer, 60 minutes fire rated car door. Car Entrance :- Clear opening (M-2087) The cost will include all statutory approval govt authorities.

Sakthivel

A T Santhanam