Repair/ replacement and Maintenance of LT switchgears, distribution system and allied works at Mil Stn Beas and Jandiala Guru under GE Kapurthala

Taking down existing LT panel by disconnecting all incoming and outgoing cables, earthing connection, dismantling PCC and making good the disturbed surface all as directed

Supply fabricating erecting LT panel outdoor type CPRI approved double door totally enclosed weather and vermin proof suitably ventilated 415 Volts 50 cycles, AC supply factory made fully compart mentalized made out of 3.00 mm thick CRCA sheet for laod bearing and 2.00 mm thick for nonload bearing protection of enclose IP 54 as per IS 2147 of 1962 with pretreatment and powder coated of approved colour including suitable size of angle iron/flat iron frame work/ support minium 45 cm required civil works, excavation & earth work, PCC foundation etc, installation, testing & commissioning with including the following :- (a) Aluminium bus bar of capacity 400 Amps for Three phase and Neutral. -04 No's (b) Combined Voltmeter 415V, Ammeter 0 to 500 Amps digital type with built in selector switch CTS of suitable ratio (Set of Three), Indicator lamp Incoming :- (i) MCCB 4P 250 Amps, 36 KA 415 Volts (Adjustable- 01 No Outgoing :- (i) MCCB FP 125 Amps 16 KA 415 Volts (adjustable 70% to 100%)- 02 N (ii) MCB TPN, 63 Amps, 16 KA 415 Volts.- 02 No's (iii) Digital type Digital Timer switch suitable for 3 phase, 415 volts AC supply for street light feeder, current capacity 16 Amps

Supply fabricating erecting LT panel outdoor type CPRI approved double door totally enclosed weather and vermin proof suitably ventilated 415 Volts 50 cycles, AC supply factory made fully compart mentalized made out of 3.14 mm thick CRCA sheet for laod bearing and 2.00 mm thick for nonload bearing protection of enclose IP 54 as per IS 2147 of 1962 with pretreatment and powder coated of approved colour including suitable size of angle iron/flat iron frame work/ support minium 45 cm required civil works, excavation & earth work, PCC foundation etc, installation, testing & commissioning with including the following :- (a) Aluminium bus bar of capacity 250 Amps for three phase and Neutral.-04 No's (b) Combined Voltmeter & Ammeter 0 to 500 Amps digital type with built in selector switch CTS of suitable ratio (Set of Three) Incoming :- (i) MCCB TPN 160 Amps, 36 KA 415 Volts - 01 No's Outgoing :- (i) MCCB 4 pole 100 Amps 16 KA 415 Volts - 02 No' (ii) MCCB 4 pole 63 Amps 16 KA, 415 Volts - 02 No's

S&F in replacement factory made power coated vertical DBs TPN 440 Volt 4 way , in double door suitable for flush mounting and surface mounting with 250 Amp copper busbar for each phase with 2 neutral bar, 2 earthbar and cable ties for cable management and fully insulated bus bar and shrounded neutral bus bar with provision of 100-160 Amp FP MCCB as Incommer and SP 6 to 32 Amp and 40 to 63 Amp for outgoing including taking down UNSV DBs complete all as specified and directed.

Taking down old unsv bus bar panel any type and S & F of new aluminium bus bar panel TPN 200 Amp , 415 Volt Complete all as specified and directed.

Taking down old unsv bus bar panel any type and S & F of new aluminium bus bar panel TPN 100 Amp , 415 Volt Complete all as specified and directed.

M&L for earthing complete with galvanized iron or steel or steel earth plate electrode of size 60cmx60cmx6.3mm thick buried directly in ground, vertically to a depth not less than 2.25 mtr below normal ground level with top edge of earth plate at depth of not less than 1.5 mtr below ground level surrounded from all sides with alternate layers of charcoal and common salt and connected to GI Strip of size 32x6 mm by means of GI bolts, nuts washers & check nuts electrode connected to main switch board or main control board or on poles or on transformer and GI pipe light grade 20 mm bore for watering including providing funnel and wire mesh GI frame and 10 cm thick suitably reinforced RCC pit cover PCC chamber pit with PCC 1:3:6 type C2 using 40mm graded stone aggregates complete including excavation and earth work, disposal of surplus soil to a distance not exceeding 50 mtr all as specified and shown in plate No 5 of SRR-1991 Part-1 .

M&L for earthing complete with galvanized steel earth plate electrode 60 cm x 60 cm x 6 mm thick surrounded with charcoal and salt, buried directly in ground (earth pit not less than 2.25 metre deep below ground level) with top edge of plate not less than 1.5 metre below normal ground level connected to galvanized earth lead wire 4 mm dia by means of bolts, nuts, check nuts and washers of galvanized iron or steel all as shown in electrical Plate No 3 of MES SSR Part-I connected to main switch board or main control board all as specified and testing on completion including provision of earth wire protected by galvanized iron 15 mm dia light grade pipe and watering pipe shall be 20 mm bore light grade including all excavation and earth work in any type of soil, PCC pit with pre-cast RCC cover, charcoal/salt, funnel etc complete all as directed.

M&L for preparation to steel surface of existing LT panels, LT feeder pillars boxes of any size and description internally and externally after scraping and scratching the old paint with emery paper etc, and painting with two coat of gray painting with spray gun and writing feeder names and numbers with suitable capital letters in English with white paint on and a black paint strip of size 20 cm x 25 cm all as directed.

M&L for repair to LT panels feeder pillar box by dismantling old rusted and perished doors shutter and bus bar covers etc and providing new doors shutters, bus bar cover etc by cutting, welding, fabricating and made to existing shape with 3.15 mm plain black sheet and angle iron of required size including providing hinges and locking arrangement all as directed including M&L for two coat of painting with synthetic enameled Grey paint over a coat of red oxide primer.