BALANCE WORK OF SPECIAL REPAIR TO CERTAIN BLDG AT D CAMP AND ALBERT EKKA ENCLAVE AT PANAGARH MIL STN UNDER GE PANAGARH

Amount

B/R PORTION

Taking down cement plaster/lime plaster of any description on concrete or Brick wall surfaces such as soffit of RCC slab, chajjas and brick walls etc including raking out joints, hacking for key, scrubbing down with water etc ,complete all as specified and as directed by Engrs-In-Charge.

M&L for Rendering 15 mm thick cement plaster in CM 1:6 on fair faces of brick/concrete work surfaces ,complete all as specified and as directed by Engrs-In-Charge.

M&L for Rendering 15 mm thick cement plaster in CM 1:4 on other than fair faces of brick/concrete surfaces finished and smooth without useing extra cement and using water proofing compound @ 3% by weight of cement content ,complete all as specified and as directed by Engrs-In-Charge. Note :- WPC will measuered and paid separatly under relevant item of schedule.

M&L for Rendering 20 mm thick cement plaster in two coats (each coat 10 mm thick) on external surfaces of brick work in CM 1:4 and second coat to be applied with WPC including fair finishing ,complete all as specified and as directed by Engrs-In-Charge. Note :- WPC will measuered and paid separatly under relevant item of schedule.

M&L for rendering 5mm thick on fair faces of ceiling / chajja concrete surfaces in cement mortar 1:3 ,complete all as specified and as directed by Engrs-In-Charge.

Supply only Integral water proofing compound ,complete all as specified and as directed by Engrs-In-Charge.

Demolition of cement concrete in ground floor & paving n. exc 15 cm thick (below or above GL) unreinforced ,complete all as specified and as directed by Engrs-In-Charge.

Demolition of RCC of any description including (renforcement cut as per requred)order to be dismanted ,complete all as specified and as directed by Engrs-In-Charge.

M&L for TMT mild steel bars 10mm dia and over,cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with theincluding mild steel wire (annealed) not less than 0.9mmdia or securing with clips ,complete all as specified and as directed by Engrs-In-Charge.

M&L for RCC M-25 (using 20 mm graded stone aggregate slabs supported on walls ,complete all as specified and as directed by Engrs-In-Charge.

M&L for RCC (1:2:4) type B1 (nominal mix) using 20 mm graded stone aggregate as in slab supported on wall, beams, cantilever, bressummers, lintel and the like etc ,complete all as specified and as directed by Engrs-In-Charge.

Use and waste of formwork to roof slub slub as like not including 200 mm thick horizontal and vertical surface of concrete flat ,complete all as specified and as directed by Engrs-In-Charge.

M&L for broken bricks hard core gauge n.exc 63mm deposited, spred and levelled in layers n.exc 15cm thick, watered and rammed to a true surfaces ,complete all as specified and as directed by Engrs-In-Charge.

M&L for 25 mm thick PCC type B-1, 1:2:4 (using 25 mm graded stone aggregate) as in laying of floor finishes and finishing even ,complete all as specified and as directed by Engrs-In-Charge.

M&L for 75mm PCC 1:3:6 type C2 using 40mm graded stone aggregate as in plinth protection ,foot path and hard standing ,complete all as specified and as directed by Engrs-In-Charge.

M&L for Cement concrete 1:3:6 type C-2 (using 40mm graded stone aggregate) as in surface channels and drain ,complete all as specified and as directed by Engrs-In-Charge.

M&L for forming construction joint 30mm deep X 10mm wide with sealing compound grade A ,complete all as specified and as directed by Engrs-In-Charge.

M&L for providing cement concrete type B0 1:2:4 (12.5mm graded aggregate) as in coping to chajja tops and all other similar works ,complete all as specified and as directed by Engrs-In-Charge.

S&F in repair's vitreous China squatting pan, ' Orissa patteren, size 580 x 440 mm white, with integral footrests (excluding flushing cisteren and flush pipe) ,complete all as specified and as directed by Engrs-In-Charge.

Supply & Fix flush pipe of polyethylene of low or high density of PVC, 32 mm dia, for low level cistern ,complete all as specified and as directed by Engrs-In-Charge.

M&L for (a) providing and laying water proofing treatment of sunken portion of WCs, bathroom etc by applying cement slurry with acrylic based modified cementitaous composite compound coating of make as approved in technical instruction 5/2003 (b) First layer of slurry of cement @ 0.5 Kg/Sqm mixed with acrylic based polymer modified cementatious composite compounds @ 0.250 Kg/Sqm. This layer will be allowed to air cure for 4 hours. (c) second slurry of cement @ 0.500 Kg/Sqm mixed with acrylic based polymer modified cementatious composite compounds @ 0.250 Kg/Sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. (d) 200 micron thick polythene film pasted with the help of bituminous adhesive shall be provided over treatment ,complete all as specified and as directed by Engrs-In-Charge.

M&L for PCC 1:4:8, type D2 (using 40 mm graded stone aggregate) as in foundation filling and mass concrete ,complete all as specified and as directed by Engrs-In-Charge.

S&F vitreous China wash basin white, flat back,size 580X450 mm including cutting for pinning in ends of brackets ,complete all as specified and as directed by Engrs-In-Charge.

S&F in repairs 10 litre capacity PVC low level flushing cistern with all accessories complete fixed with WC including syphone pipe, PVC flushing pipe of size ,complete all as specified and as directed by Engrs-In-Charge.

S&F in repair 10 litre capacity PVC valveless, syphonic action type low level flushing cistern with all accessories complete fixed with WC including syphone pipe, PVC flushing pipe of size with bracket ,complete all as specified and as directed by Engrs-In-Charge.

S&F 15 mm bore stop valve cast copper alloy screwed down, high pressure, with crutch or but-ter fly handle, screwed both ends for iron pipe or for unions ,complete all as specified and as directed by Engrs-In-Charge.

S&F in repair's 15 mm bore conceled stop valve cast copper alloy screwed down, high pressure, with crutch or butter fly handle, screwed both ends for iron pipe or for unions ,complete all as specified and as directed by Engrs-In-Charge.

S&F in repair's stop valve cast copper chromium plated concealed type screwed down, high pressure with capstan head suitable for 15 mm bore ,complete all as specified and as directed by Engrs-In-Charge.

S&F PVC connection 15mm size PTMT nuts of length 450mm ,complete all as specified and as directed by Engrs-In-Charge.

S&F PVC connection 15mm size PTMT nuts of length 600mm ,complete all as specified and as directed by Engrs-In-Charge.

S&F 15mm bore piller taps cast copper alloy,with capstan heads,chromium plated,screwed down, fancy type high pressure, with or without lettred 'HOT or 'COLD' with long screwed sunk and fly nuts ,complete all as specified and as directed by Engrs-In-Charge.

S&F in repair's bib taps cast copper alloy 15mm bore with fancy chromium plated screwed down, screwed for iron pipe or for brass ferrule ,complete all as specified and as directed by Engrs-In-Charge.

S&F in repair's grating square 150mm size of PTMT(minimum 100 gms) ,complete all as specified and as directed by Engrs-In-Charge.

S&F in repair's grating square 150mm size of PTMT(minimum 100 gms) ,complete all as specified and as directed by Engrs-In-Charge.

S&F sink made of stainless steel 1mm thick kitchen or labortory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495 mm x 420 mm and bowl size 410mm x 330mm x 106 mm ,complete all as specified and as directed by Engrs-In-Charge.

S&F in repair's 75mm PVC (SWR) floor trap including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) ,complete all as specified and as directed by Engrs-In-Charge.

S&F in repair's PVC waste pipe 32mm dia for wash basin and sink 01 meter long ,complete all as specified and as directed by Engrs-In-Charge.

S&F in repair's tubular towel rail, brass chromium plated 20 mm dia `D' type 60 cm long between flanges ,complete all as specified and as directed by Engrs-In-Charge.

S&F in repair's shelf of PTMT fixed with and including chromium plated brass screw and wooden/plastic cleats ( min weight 300 gms) ,complete all as specified and as directed by Engrs-In-Charge.

S&F in repair's chromium plated shower roses 125 mm long with or without swivel joints, any size, including fixing fixing to steel pipe or union ,complete all as specified and as directed by Engrs-In-Charge.

Dismantling of floor hearth or wall tiling including cement mortar bedding but not backing and removing serviceable tiles to store yard and rubbish off the primises ,complete all as specified and as directed by Engrs-In-Charge.

M&L for Non Skid joint free coloured ceramic tiles 7 to8 mm thick (Square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match ,complete all as specified and as directed by Engrs-In-Charge.

M&L for Non Skid joint free coloured ceramic tiles 7 to8 mm thick (Square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match ,complete all as specified and as directed by Engrs-In-Charge.

M&L for cement concrete type B0 (1:2:4) using 12.5 mm graded aggregate 25 mm thick as in floor for receiving screed bed of floor tiling ,complete all as specified and as directed by Engrs-In-Charge.

M&L for Screed bed or bedding layer of mortar 15 mm thick in (1:6) for laying floor finishes like tiles etc ,complete all as specified and as directed by Engrs-In-Charge.

M&L for rendering 10 mm thick on fair faces of brick work in CM (1:4) for receving vertical dado tiling ,complete all as specified and as directed by Engrs-In-Charge.

M&L for glazed tiles coloured ceramic tiles 200x300x 6 to 7 mm thick in vertical surfaces such as skirting and dados set and jointed in neat cement slurry painted in coloured cement to match ,complete all as specified and as directed by Engrs-In-Charge.

M&L for glazed ceramic tiles 300 x 200 mm x 7 mm thick in vertical surfaces such as risers, skirting and dados, set and jointed in neat cement slurry and pointed in coloured cement to match including 10 mm thick cement plaster in CM 1:4 on brick or concrete surfaces ,complete all as specified and as directed by Engrs-In-Charge.

M&L for 20 mm thick granite Machine cut jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing ,complete all as specified and as directed by Engrs-In-Charge.

M&L for 20 mm thick Granite for cooking plartforms and like in CM 1:4 including pointing in white cement (1:2) ,complete all as specified and as directed by Engrs-In-Charge.

Rounding to edges of stone slabs exposed edge, such as in steps, cooking platform and other similar situation ,complete all as specified and as directed by Engrs-In-Charge.

Taking down chowkats or frames exc 1.5 sqm but n. exc 4 sqm each (without taking off shutters from the frame) ,complete all as specified and as directed by Engrs-In-Charge.

Taking down of chowkats or frames not exc 1.5sqm without taking off shutters from frames ,complete all as specified and as directed by Engrs-In-Charge.

M&L for 2nd class hard wood plain, solid, straight chowkhats and frames, wrought framed rebated on the solid, rounded or chamfered put together with glue, pinned at joints ,complete all as specified and as directed by Engrs-In-Charge.

S&F steel windows with side hung shutters including projection type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded ,complete all as specified and as directed by Engrs-In-Charge.

S&F steel windows with side hung shutters including projection type hinges with out steel handle, and steel peg stay, complete without glazing bars, dovetailed or welded ,complete all as specified and as directed by Engrs-In-Charge.

S&F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples ,complete all as specified and as directed by Engrs-In-Charge.

S&F in repair's stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples ,complete all as specified and as directed by Engrs-In-Charge.

S&F steel ventilator with top hung shutter including hinges, steel peg stay ,complete all as specified and as directed by Engrs-In-Charge.

M&L for framed work such as grills etc with ends of bars shouldred and or riveted or forged into spike, framed guard bars and similar work conforming to Fe 290.Gde-E-165 ,complete all as specified and as directed by Engrs-In-Charge.

M&L for PCC (1:2:4) type B-0 as in bed blocks for hold fast including necesssary formwork ,complete all as specified and as directed by Engrs-In-Charge.

S&F mild steel flat iron as in hold fast, clamps articles conforming to FE 290 Gde-E-165 ,complete all as specified and as directed by Engrs-In-Charge.

M&L for 18/19 mm thick prelamenated partical board interior graded one side prelaminated and other side balancing white ,complete all as specified and as directed by Engrs-In-Charge.

S&F Factory made 35 mm thick 2nd H.W plain framed panelled shutters (two panel) with lock rail and panel of 9mm thick B.W.P commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per ISI : 1003 (Part-I), kiln seasoned and chemically pressure treated ,complete all as specified and as directed by Engrs-In-Charge.

S&F 2nd class hard wood 35mm thick Glazed and skelton shutters, open rebated and prepared to receive glass, gauge etc(without sash bars) edges of framing plain, chamfered or rounded, fittted with cut and mitred beads for securing gauge,etc sizes of member of shutter as specified SSR part-I Section 8 clause 8.24 (a) ,complete all as specified and as directed by Engrs-In-Charge.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S Square tube, suppling & fixing in opening as per specification & drawing ,complete all as specified and as directed by Engrs-In-Charge.

S&F Factory made solid panel pvc door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded palin colour PVC `C' channel heaving a PVC sheert strip of 20mm width suck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bbottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S frame wedded/ sealed to the stiles, & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing ,complete all as specified and as directed by Engrs-In-Charge.

M&L for sheet glass 3 mm thick ordinary quality and glazing with oil putty in square n. exc 0.50 sqm each pane ,complete all as specified and as directed by Engrs-In-Charge.

S&F butt hinges, extruded alluminium,with mild steel hinge pin,bright polished and fixed, type 75 mm size C21 ,complete all as specified and as directed by Engrs-In-Charge.

S&F 100 mm butt hinges medium weight cold rolled mild steel ,complete all as specified and as directed by Engrs-In-Charge..

S&F aluminium anodised 200 mm barrel tower bolts of extruded section ,complete all as specified and as directed by Engrs-In-Charge.

S&F aluminium anodised 150 mm barrel tower bolts of extruded section ,complete all as specified and as directed by Engrs-In-Charge.

S&F 150 mm long aluminium alloy handles,fabricated type, anodised ,complete all as specified and as directed by Engrs-In-Charge.

S&F 125 mm long aluminium alloy handles,fabricated type, anodised ,complete all as specified and as directed by Engrs-In-Charge.

S&F 300 mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed ,complete all as specified and as directed by Engrs-In-Charge.

S&F 100 mm long hasp and staple, aluminium anodized with bolt to hinge plate and fixed with screws ,complete all as specified and as directed by Engrs-In-Charge.

S&F small fittings 2nd class hard wood such as brakcets of any type latch and hinge block shaped door and window stops and the like of 1st class hard wood including all necessary labour articles n. exc 200 cum each ,complete all as specified and as directed by Engrs-In-Charge.

S&F 300 mm mild steel ordinary rat tail rod pattern spring including roller and solar plates ,complete all as specified and as directed by Engrs-In-Charge.

S&F in repair's curtain rods/ harison mild steel chromium plated with fittings stainless steel brackets, stops, rollers etc ,complete all as specified and as directed by Engrs-In-Charge.

M&L for PCC(1:2:4) type B-1 (using 20mm graded aggregate) as in roof kerbs or mud stop rounded ,complete all as specified and as directed by Engrs-In-Charge.

Taking up or down steel tubing and connection including cleaning for refixing or removed to store,15 mm dia bore ,complete all as specified and as directed by Engrs-In-Charge.

Taking up or down steel tubing and connection including cleaning for refixing or removed to store,20 mm dia bore ,complete all as specified and as directed by Engrs-In-Charge.

Cutting chases, pinning in making good to facing on brick walls where required and pointing in cement mortar (1:3) to ends for concealed water tubing and making good, cutting n. exc. 10cm girth ,complete all as specified and as directed by Engrs-In-Charge.

S&F GI tubing 15mm bore medium grade with all fittings and fixed complete to wall and ceiling or laid in floors ,complete all as specified and as directed by Engrs-In-Charge.

S&F GI tubing 20 mm bore medium grade with all fittings and fixed complete to wall and ceiling or laid in floors ,complete all as specified and as directed by Engrs-In-Charge.

S&F 20 mm outer dia medium grade CPVC, SDR 11 with all fittings and fixed complete to walls and ceiling or laid in floors ,complete all as specified and as directed by Engrs-In-Charge.

S&F 25 mm outer dia medium grade CPVC, SDR 11 with all fittings and fixed complete to walls and ceiling or laid in floors ,complete all as specified and as directed by Engrs-In-Charge.

Dismantling of cast iron 100 mm dia pipes jointed in cement mortar ,complete all as specified and as directed by Engrs-In-Charge.

Dismantling of cast iron 75mm dia pipes jointed in cement mortar ,complete all as specified and as directed by Engrs-In-Charge.

S&F PVC SWR pipes 110 mm bore single socketed in any length with rubber ring joint fixed to wall or laid in trenches or in floors with steel clamps ,complete all as specified and as directed by Engrs-In-Charge.. Make : Supreme/ Finolex.

S&F PVC SWR pipes 75 mm bore single socketed in any length with rubber ring joint fixed to wall or laid in trenches or in floors with steel clamps ,complete all as specified and as directed by Engrs-In-Charge.

S&F PVC (SWR) 75 mm Bends (any radius) ,complete all as specified and as directed by Engrs-In-Charge.3.

S&F PVC SWR bends of 110 mm bore ,complete all as specified and as directed by Engrs-In-Charge.

S&F PVC SWR bends of 75 mm bore ,complete all as specified and as directed by Engrs-In-Charge.

S&F PVC (SWR) junction single (single T) equal or unequal provided with access door of 110 mm dia,complete all as specified and as directed by Engrs-In-Charge.

S&F PVC (SWR) junction single (single T) equal or unequal provided with access door of 75 mm dia ,complete all as specified and as directed by Engrs-In-Charge.

S&F PVC (SWR) junction double (double T) equal or unequal provided with access door of 75 mm dia ,complete all as specified and as directed by Engrs-In-Charge.

S&F PVC (SWR) nahni trap plain including jointing with solvent cement 75 mm dia ,complete all as specified and as directed by Engrs-In-Charge.

S&F PVC (SWR) reducer of 110 mm dia ,complete all as specified and as directed by Engrs-In-Charge.

S&F PVC (SWR) vent cowl 75 mm bore ,complete all as specified and as directed by Engrs-In-Charge.

S&F PVC (SWR) WC connector with lip ring 110 mm ,complete all as specified and as directed by Engrs-In-Charge.

S&F PVC (SWR) gully trap 125/110 mm setting and jointing with solvent cement ,complete all as specified and as directed by Engrs-In-Charge.

M&L for complete removal/scrapping of existing treatment of plastered surfaces and applying one coat of alkali resistanse primer over 3 mm thick wall care putty and two coat of oil bound distemper ,complete all as specified and as directed by Engrs-In-Charge.

M&L for prepration of newly plastered surfaces of wall and applying one coat of alkali resistanse primer over 3 mm thick wall care putty and two coat of oil bound distemper ,complete all as specified and as directed by Engrs-In-Charge.

Removal of complete existing treatment of any description on roof surfaces of any description and roughening surfaces of old concrete floor by picking sweeping clean and washing down with water to remove dust, foreign items ,complete all as specified and as directed by Engrs-In-Charge.

M&L for Preparation of new plastered surface of wall applying of two coats of cement base paint over a coat alkali resistant primer ,complete all as specified and as directed by Engrs-In-Charge.

M&L for prepartion of newly plastered ceiling surfaces and applying three coat of white wash ,complete all as specified and as directed by Engrs-In-Charge.

M&L for prepartion of old plastered ceiling surfaces and applying two coat of white wash ,complete all as specified and as directed by Engrs-In-Charge.

M&L for preperation of newly plastered surfaces of wall and applying two coats of cement based paint over a coat of primer ,complete all as specified and as directed by Engrs-In-Charge.

M&L for Preparation of old plastered surface of wall applying of two coats of cement base paint ,complete all as specified and as directed by Engrs-In-Charge.

M&L for preperation of old plastered surfaces of wall and applying one coats of cement based paint including complete removal of exc treatment complete all as specified and directed.

M&L for preparation of new surfaces of walls and apply two coat of oil emulsion distemper to walls over a coat of primer ,complete all as specified and as directed by Engrs-In-Charge.

M&L for preparation of old surfaces of walls and apply two coat of oil emulsion distemper to walls ,complete all as specified and as directed by Engrs-In-Charge.

M&L for 3 mm thick wall care putty in wall ,complete all as specified and as directed by Engrs-In-Charge.

M&L for preparation of newly painted steel surfaces of any description, over 10 cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide, zinc chrome ,complete all as specified and as directed by Engrs-In-Charge.

M&L for preparation of old painted steel surfaces of any description, over 10 cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint ,complete all as specified and as directed by Engrs-In-Charge.

M&L for prepartion of old ceiling surfaces and applying one coat of white wash ,complete all as specified and as directed by Engrs-In-Charge.

M&L for applying two coats of synthetic enamel paint over a coat of pink primer including preparation of new wood surfaces of any description not other wise described over 10 cm with or girth ,complete all as specified and as directed by Engrs-In-Charge.

M&L for applying two coats of synthetic enamel paint including preparation of old wood surfaces of any description not other wise described over 10 cm with or girth ,complete all as specified and as directed by Engrs-In-Charge.

Supply & Fixing stainless steel kitchen plate rack made out of 0.63mm thick stainless steel of size 750x600mm including screws ,complete all as specified and as directed by Engrs-In-Charge.

S&F Kitchen stainless steel plate rack made out of 1 mm thick sheet and having partions as per sample. The over all size 900x600mm fixed with steel fastners or steel screw comp all as per sample kept in AGE B/R ‘A’ office,complete all as specified and as directed by Engrs-In-Charge.

S&F in repair's MS.PVC caoted drepary rods of 25 mm dia as in curtain rods ,complete all as specified and as directed by Engrs-In-Charge.

S&F MS PVC sheeted/power coated bracket size 150mm made to shape suitable for holding curtain/drapery of rod of 25mm dia fixed with PVC rawl plugs and MS steel screws ,complete all as specified and as directed by Engrs-In-Charge and as per approved sample kept in AGE B/R 1 office for single/double rod system.

S&F for coloured conical end balls dia not less then 50mm and PVC coated made to shape suitable for fixing as end of curtain/dropery rods ,complete all as specified and as directed by Engrs-In-Charge and as per approved sample kept in AGE B/R 1 office.

Dismantling of Asbestos cement (corrugated, semi corrugated etc) of any thickness including ridges, hips, valleys as in roof coverings ,complete all as specified and as directed by Engrs-In-Charge.

S&F Pre - Painted galvanized aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws ,complete all as specified and as directed by Engrs-In-Charge.

S&F Pre - Painted galvanized aluminium zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws ,complete all as specified and as directed by Engrs-In-Charge.

Dismantling of wall or ceilling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, of any thickness including cover fillets ,complete all as specified and as directed by Engrs-In-Charge.

S&F False Ceiling with powder coated exposed GI grid suspension system (E grid T 2430 or equivalent load caring capacity with mild span deflection not exceeding 1/360 span with hanger spacing of 1200 mm c/c) Made out of 0.5mm thick G.I. main tee size 32 X 24 mm , cross tee of size 26 X24 mm an dangle of size 20 X 20 mm fixed in wall , all powder coated finish on exposed faces of tee and angle , hung from cealing . The wall angle shall be fixed on pvc dash fastner on the peremeter of the wall screws with distance 300 mm c/c . The main runner to be intserted in th epre-cut slot of main runner at a regulate interval of 600 mm to form a modular rid mm shall be placed perpendicular to the cross tee 120 mm long to finallt form a rod of 600 X 600 mm shall be suported by 2 mm dia GI wire from purlin /Soffit. And 4 mm thick high pressure systrm cureds non asbestos fiber cement designer ceiling board (density > 1200 kg/ cum ) of size 595 x 595 mm confroming IS 14862 & Type b category III of ISO 8336 Tested as per AS - 1530 part 3 & BS-476 4 to 6 should be placed in grid module to form a false ceiling including dismantling of old ceiling board of any description complete all as specefied and as per manufacturer drawing and as directed by Engrs-in- Charge

M&L for Providing and fixing non asbestos designer fiber cementbuilding board 6 mm thick in ceilling fixed to aluminium frame work as per manufacture instruction ,complete all as specified and as directed by Engrs-In-Charge.

S&F hangers 6mm dia GI (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40 x 3mm size 60mm long and expansion hold fasteners 12.5mm dia, 40mm long ,complete all as specified and as directed by Engrs-In-Charge.

Dismantling cast iron work of any description ,complete all as specified and as directed by Engrs-In-Charge.

S & F steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St.-240 ,complete all as specified and as directed by Engrs-In-Charge.

M & L for machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including 20 mm thick screed bed (1:6) CM and rubbing and polishing for stair case ,complete all as specified and as directed by Engrs-In-Charge.

M & L for machine cut kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment including 10 mm thick rendering 1:4 in CM ,complete all as specified and as directed by Engrs-In-Charge.

S&F Joist channel angle of tee section fixed independently without connecting plate as Fe 410 W (Gde-E-250 quality A) ,complete all as specified and as directed by Engrs-In-Charge.

Demolition of brick work built in cement mortar or cement lime mortar incl all quoins, arches pillars etc and removing unserviceable material exc 100 mtr ,complete all as specified and as directed by Engrs-In-Charge.

M&L for brick work with fly ash bricks straight or curved on plan exc 6 m mean radius build in CM 1:6 ,complete all as specified and as directed by Engrs-In-Charge.

M&L for brick work with half bricks thick fly ash bricks straight or curved on plan exc 6 m mean radius build in CM 1:6,complete all as specified and as directed by Engrs-In-Charge.

M&L for 100 mm thick cement concrete type D-2, 1:4:8 (40mm graded stone aggregate) as in sub base of flooring all as specified.

M&L for 75 mm thick cement concrete type B-1, 1:2:4 (20mm graded stone aggregate) as in flooring ,complete all as specified and as directed by Engrs-In-Charge.

Material and labour for 25 mm thick chequered cement concrete tiles of approved size, set, jointed and pointed using with grey cement and pigment in floors, paving etc. including the setting and jointing in neat cement paste or slurry 0.3kg/Sqm over 20 mm thick screed bed or bedding layer in cement mortar 1:4 complete as per manufacturer instructions and all as specified and as directed by Engrs-In-Charge.

M&L for 2 nd class hardwood weather boarding clean sawn plain 20 mm thick or feather edged 15 mm to 20 mm thick and fixed with 30 mm laps ,complete all as specified and as directed by Engrs-In-Charge.

M&L for brickwork with old size subclass 'B' bricks, straight or curved on plan exc 6m mean radius, built in CM 1:4 ,complete all as specified and as directed by Engrs-In-Charge.

M&L for brick work with old size sub class ‘B’ bricks straight or curved on plan to any radius in half bricks thick walls, built in CM 1:4 ,complete all as specified and as directed by Engrs-In-Charge.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete using extra cement including forms, moulds, mitred/stopped ends ,complete all as specified and as directed by Engrs-In-Charge.

1st Layer:- Grading with cement concrete - M & L for 25 mm thick average PCC 1:2:4 type B-1 (20 mm graded aggregate) for grading in roof all as per Para 11.42.2 of SSR Part –I 2009 ,complete all as specified and as directed by Engrs-In-Charge.

M&L for rendering 5mm thick on fair faces on roof surfaces of concrete surfaces in cement mortar 1:4 without using extra cement veen and smooth ,complete all as specified and as directed by Engrs-In-Charge. (WPC will be measured and paid separately).

2nd Layer :- Application of Primer - M&L for primer the surface with a mixture of water based UV resistant single component elastomeric PU liquid membrane in situ for waterproofing and potable water in the ratio of 1:1 i.e. (200 gm primer & 200ml water or as per manufacturer instruction) and apply @ 400gm/sqm or as per manufacturer instruction of the mixture and allow to touch dry shall be applied on the prepared surface. complete all as specified and as directed by Engr-in-Charge.

3rd Layer: M&L for first coat of water based UV resistant single component elastomeric PU liquid membrane in situ for waterproofing @ 1 Kg/Sqm by roller/airless spray while the primed surface is takly and spread non-woven geo-textile mesh of 40/50 gsm with overlaps of 50mm in both directions when the surface is still tackly, second coat of water based UV resistant single component elastomeric PU liquid membrane in situ for waterproofing @ 1 Kg/Sqm by roller/airless spray for final DFT of 1500 micron complete all as specified and as directed by Engr-in-Charge.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work;not exceeding 200mm thick (Horizontal or sloping) ,complete all as specified and as directed by Engrs-In-Charge.

S & F Contineous (Piano) hinges, mild steel, bright finish or electrogalvanished (width of flaps 30mm) ,complete all as specified and as directed by Engrs-In-Charge.

S & F 40mm dia, cupboard knobs fixed with nut, screw and washer of mild steel, bright finished ,complete all as specified and as directed by Engrs-In-Charge.

S & F Ball catches with 8mm dia steel ball,and brass body and striking plate including letting in and fixed 140mm overall length of cover plate,complete all as specified and as directed by Engrs-In-Charge.

S & F cast iron or mild steel Wardrobe hooks (single) 50mm to 60mm ,complete all as specified and as directed by Engrs-In-Charge.

E/M PORTION

Taking down carefully copper/aluminium conductor point wiring (light,fan,socket or power) complete including fittings such as switches,ceiling roses, pendants, regulators ,sockets etc. and removing (except those to be reused shall be kept in safe custody at the site ) and making good disturbed surfaces of walls, floors etc.to match with the existing ,complete all as specified and as directed by Engrs-In-Charge.

Taking down carefully by unscrewing from boards/outlet boxes, fittings and fixtures such as switches sockets, ceiling roses, lamp holders, brackets, ceiling fittings, bulk head fittings, tube light fittings and regulators, etc. for reuse at site or carrying to the store (To be measured only when found serviceable in all respects complete for reuse) ,complete all as specified and as directed by Engrs-In-Charge.

Material and labour point wiring for light point/ fan point, one light/fan/exhaust fan point controlled by one, one way switch using 1.5 sqmm nominal cross sectional area multistranded copper conductor ,PVC insulated unsheathed FRLS cables in and including 20 mm dia or higher size PVC concealed conduits and fittings of medium grade, including pressed steel terminal switch boxes, 3 mm thick bakelite sheet top cover (ISI Marked) fitted with chromium plated brass screws & washers and 1.5 sqmm nominal cross sectioanl area multistranded copper conductor FRLS PVC insulated unsheathed earth wire and connecting to earth dolly and brass screws, washers etc. ,complete all as specified and as directed by Engrs-In-Charge.

Material and labour wiring for switch socket out let on independent Boards controlled by one, one way switch using 2.5 sqmm nominal cross sectional area multistranded copper conductor, PVC insulated unsheathed FRLS cables in and including 20 mm dia or higher size PVC concealed conduits and fittings, including pressed steel terminal switch boxes , 3 mm thick bakelite sheet top cover (ISI Marked) fitted with Chromium plated brass screws & washers and 2.5 sqmm nominal cross sectioanl area multistranded copper conductor , PVC insulated unsheathed FRLS cable earth wire and connecting to earth dolly and brass screws, washers etc. ,complete all as specified and as directed by Engrs-In-Charge.

All as per item No.2.003 mentioned here-in-before but for 5 Amp socket on same board with other switches.

All as per Item No 2.003 mentioned here-in- before but for one light point controlled by two -2 way switches.

Material and labour wiring for socket outlet 3 pin, 15 amps on independent Boards controlled by one, one way switch using 4 sqmm nominal cross sectional area multistranded copper conductor, PVC insulated unsheathed FRLS cables in and including 20 mm dia or higher size PVC concealed conduits and fittings, including pressed steel terminal switch boxes , 3 mm thick bakelite sheet top cover (ISI Marked) fitted with Chromium plated brass screws & washers and 4.0 sqmm nominal cross sectioanl area multistranded copper conductor , PVC insulated unsheathed FRLS cable earth wire and connecting to earth dolly and brass screws, washers etc. ,complete all as specified and as directed by Engrs-In-Charge.

Material and labour wiring for socket outlet 3 pin, 15 amps on independent Boards controlled by one, one way switch using 4 sqmm nominal cross sectional area multistranded copper conductor, PVC insulated unsheathed FRLS cables in and including 20 mm dia or higher size PVC concealed conduits and fittings, including pressed steel terminal switch boxes , 3 mm thick bakelite sheet top cover (ISI Marked) fitted with Chromium plated brass screws & washers and 2.5 sqmm nominal cross sectioanl area multistranded copper conductor , PVC insulated unsheathed FRLS cable earth wire and connecting to earth dolly and brass screws, washers etc. ,complete all as specified and as directed by Engrs-In-Charge.

Supply and fixed switch piano flush type, single pole , 6 Amps, one way ,complete all as specified and as directed by Engrs-In-Charge.

Supply and fixed switch socket 2 in 1 multipurpose 5 pin , (6 Amps ) ,complete all as specified and as directed by Engrs-In-Charge.

Supply and fixed Socket outlet 3 pin, 5A, flush type ,complete all as specified and as directed by Engrs-In-Charge.

Supply and fixed switch 16 Amps flush type controlled by one switch ,complete all as specified and as directed by Engrs-In-Charge.

Supply and fixed socket 2 in 1 , 6 pin , (16 Amps ) ,complete all as specified and as directed by Engrs-In-Charge.

Supply & fixed ceiling rose surface bakelite 65 mm x 50 mm two to three terminal suitable for 230 Volts AC 6 Amps ,complete all as specified and as directed by Engrs-In-Charge.

Supply & fixed stepped type electronic fan regulator flush type 240 Volts ISI marked ,complete all as specified and as directed by Engrs-In-Charge.

Supply & fixed lamp holder, PVC/polycarbonate type with back plate straight or anfular suitable for batten fittings ,complete all as specified and as directed by Engrs-In-Charge.

Supply & fixed LED bulb 7 watts, 240 volts, ISI marked ,complete all as specified and as directed by Engrs-In-Charge.

Supply and fixed Surface mounted type decorative light fitting 1 x 12W LED 6k 230V AC, 50Hz complete with all accessories ,complete all as specified and as directed by Engrs-In-Charge.

Supply & fixed Bell push , flush type , 5 amp ,complete all as specified and as directed by Engrs-In-Charge.

Supply & fixed Buzzer, Ding dong, AC 230 Volts, single pole 230 volts ,complete all as specified and as directed by Engrs-In-Charge.

Supply & fixing exhaust ventilation fan of sweep 230mm,240 volts, metalic body, BEE 5 star rated, ISI marked ,complete all as specified and as directed by Engrs-In-Charge.

Supply & fixing GI pipe light grade 40 mm dia of size for road cross of cable,ISI marked ,complete all as specified and as directed by Engrs-In-Charge.

Supply & fixing XLPE insulated armoured cable, 25 sqmm 4 core,1100 volts grade heavy duty cable,ISI marked passing through pipe, with PVC insulated aluminium conductor served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed ,complete all as specified and as directed by Engrs-In-Charge.

Excavation in trenches not exceeding 1.5m wide and not exc. 1.5m depth and getting out in hard/dense soil ,complete all as specified and as directed by Engrs-In-Charge.

Returning, filling, including spreading, leveling, watering and well ramming in layers not exc. 25cmin soft/loose soil ,complete all as specified and as directed by Engrs-In-Charge.

Removal of excavated soil to a distance not exc 50 m and depositing where directed at a level not exc 1.5 mtr above the starting point ,complete all as specified and as directed by Engrs-In-Charge.

Supply and lay for dry river sand filling for cable protection with a layer of 8cm deep before laying and 15cm covering above the top edge of cable after laying ,complete all as specified and as directed by Engrs-In-Charge. (Note : Punned thickness shall be measured).

M&L for sub class B bricks locally available of size 25 x 12.5 x 7.5 cm laid dry width wise across the line of cable in trenches for protection of UG cable ,complete all as specified and as directed by Engrs-In-Charge.

Supplying and fixing two single core, 4 sqmm nominal cross sectional area multistranded copper conductor FRLS cable, PVC insulated unsheathed 1100 Volts grade drawing in and including suitable size PVC conduit (ISI marked), concealed, including 4 sqmm nominal cross sectional area multistranded copper conductor FRLS cable, PVC insulated unsheathed 1100 Volts grade earth wire ,complete all as specified and as directed by Engrs-In-Charge.

Supplying and fixing two single core ,6 sqmm nominal cross sectional area multistranded copper conductor FRLS cable, PVC insulated unsheathed 1100 Volts grade drawing in and including nd including suitable size PVC conduit (ISI marked), concealed, including 6 sqmm nominal cross sectional area multistranded copper conductor FRLS cable, PVC insulated unsheathed 1100 Volts grade earth wire ,complete all as specified and as directed by Engrs-In-Charge.

Supply & fixed 01x 18 W LED batten light fittings, with T-8 tube, lighting fixture with extruded polycarbonate complete with all accessories and connection from ceiling rose with twin core twisted flexible copper conductor cable with suitable size and earthing complete,complete all as specified and as directed by Engrs-In-Charge.

Supply and fixed security light fittings 25 watts, minimumm lumen output 100 lumen/Watt, made up of pressure dia cast housing with prismatic polycarbornate diffuser and individual LED with secondary optic and IP65 including necessary connection complete suitable for pole dia 25mm complete with all accessories including connected with twin core twisted flexible copper conductor of suitable size ,complete all as specified and as directed by Engrs-In-Charge. Make - Bajaj/Crompton/Phillips

Supply and fixed 9 W LED light fitting wall mounted batten 2ft , extruded polycarbonate, enivromental friendly, heat sink provided for efficent heat dissipation and integrated electronic driver for 9 watt , 6000K including necessary connection ,complete all as specified and as directed by Engrs-In-Charge.

Supply and fixed epoxy powder coated sheet metal enclosure for DBs, double door (when MCBs to be used), Single pole and neutral 240 V, 8 ways with mounting fitted with bus bar, DIN channel , neutral link and incoming contact ,complete all as specified and as directed by Engrs-In-Charge.

Supply and fixed epoxy powder coated sheet metal enclosure for DBs, double door, vertical type (when MCCBs to be used for incomming and MCB to be used for outgoing), Triple pole and neutral 415 V, 8 ways with mounting fitted with bus bar, DIN channel , neutral link and incoming contact ,complete all as specified and as directed by Engrs-In-Charge.

Supply and fixed epoxy powder coated sheet metal enclosure for DBs, double door, vertical type (when MCBs to be used), Triple pole and neutral 415 V, 8 ways with mounting fitted with bus bar, DIN channel , neutral link and incoming contact ,complete all as specified and as directed by Engrs-In-Charge.

Supply and fixed MCCB TPN 125 Amps, 'C' series 10kA, 240 Volts,ISI marked and to be housed in DBs complete including necessry connection all as specified and directed. (Note :- Proper and suitable size cable lugs to be fixed with MCB are included in unit rate of each MCB of any rating) ,complete all as specified and as directed by Engrs-In-Charge.

Supply and fixed MCCB TPN 100 Amps, 'C' series 10kA, 240 Volts,ISI marked and to be housed in DBs complete including necessry connection ,complete all as specified and as directed by Engrs-In-Charge. (Note :- Proper and suitable size cable lugs to be fixed with MCB are included in unit rate of each MCB of any rating).

Supply and fixed MCB SP, 6 to 32 Amps, 'C' series 10kA, 240 Volts and to be housed in DBs including necessry connection,complete all as specified and as directed by Engrs-In-Charge. (Note :- Proper and suitable size cable lugs to be fixed with MCB are included in unit rate of each MCB of any rating).

Supply and fixed MCB SPN 32 Amps, 'C' series 10kA, 240 Volts and to be housed in DBs complete including necessry connection ,complete all as specified and as directed by Engrs-In-Charge. (Note :- Proper and suitable size cable lugs to be fixed with MCB are included in unit rate of each MCB of any rating).

Material and labour for earthing complete with galvanised mild steel earth plate electrode 600x600x6.0mm thick, burried directly in ground to a depth not less than 2.25 metres deep below ground level with top edge of earth plate not less than 1.5 metre below normal ground level surrounded with adequate quantity of charcoal dust mixed with salt to a packed thickness of 15 cm all around the plate, using GI wire 4 mm dia as earth strip electrode bolted or rivetted to earth plate at one end and connected to equipments at another end, GI earth strip encased in and including 40 mm dia GI 'light grade' pipe from upper end of earth plate upto equipments,20 dia bore GI pipe 'light grade' as water pipe from earth chamber to upper edge of earth plate, Test point , GI funnel with wire mesh fixed on water pipe and PCC 1:2:4 type B-1 (using 20mm graded stone aggregate) as in pit chamber and RCC pit cover 50mm thick precast RCC 1:2:4 type B-1, duly reinforced with MS round bars 6mm dia @ 100 c/c both ways with 10mm dia MS round bar as in lifting handles, excavation, earth work including laying the GI pipe concealed in floor/wall all as described in electric plate of SSR Part I ,complete all as specified and as directed by Engrs-In-Charge with testing on completion. Note :- If the desired earth resistance is not found, earthing shall be redone by the contractor at no extra cost to the department.

Supply & fixing recess cum surface light round shape,240v, ISI mark, 18 watts,complete all as specified and as directed by Engrs-In-Charge.

Supply and fixing of electric water heater storage type 25 Ltrs with all fixing arrangement including nuts & bolts etc.,complete all as specified and as directed by Engrs-In-Charge.

S&F PVC Connections 15 mm size with PTMT nuts of length 300 mm long, ISI marked ,complete all as specified and as directed by Engrs-In-Charge.

Supply and laying of pipe GI medium grade 15 mm dia complete in wall ceiling or floor etc ,complete all as specified and as directed by Engrs-In-Charge.

S&F Stop valve 15mm fancy type CP cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both end for iron pipe ,complete all as specified and as directed by Engrs-In-Charge.

S&F Bib tap 15mm cast copper alloy high pressure with crutch or butterfly handle screwed for iron pipe ,complete all as specified and as directed by Engrs-In-Charge.

Supply and fix in repair for 25mm bore GI tubing medium grade in trenches/floor/pillar connection in old or new position including fittings complete all as specified and as directed.

Supply and fixed in repairs, 25mm bore dia pipe gun metal globe or gate valves, yoke type, full opening with iron wheel head, screwed both ends heavy duty ISI marked for iron pipes complete all as specified and as directed.

S&F in repairs Rotational/moulded Polyethyne water tank of capacity 500 ltr(Cylindrical, vertical with closed top) hosisted and fixed in position complete all as specified and as directed.

S&F in repair's Ball brass valves, high pressure, with polythene float and flynut complete, screwed for inron pipe or brass ferrule for 25mm bore pipe complete all as specified and as directed.

SCHEDULE OF CREDIT

Anmol Yash S.D. Construction Pvt. Ltd.

NIRMAL SALES CORPORATION

FRIENDS CONSTRUCTION