ADDN/ ALTN AND SPL REPAIR OF BLDG NO P-71, P-72 INCLUDING PROVN OF 01 X TOILET BLOCK FOR STUDENTS AT HRDC, HQ EC, ADDN/ ALTN TO SARVA DHARMA STHAL BLDG NO P-145 OF 561 SUB GP (ASCON) AND PROVN OF ROOF TREATMENT BLDG NO C-3 OF MES IB UNDER GE (FW) KO

Amount

SCHEDULE 'A' PART-I (B/R WORKS) Demolition of brick work built in cement mortar or cement lime mortar including all quoins, arches, pillars etc complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floor and paving n.exc 15 cm thick below or above GL complete all as specified and directed.

Dismantling of floor, hearth or wall tiling incl cement mortar bedding (but not backing) removing tiles from site and rubbish off the premises complete all as specified and directed.

Dismantling stone slabs and tiles, laid, bedded and pointed in any mortar of any description or thickness in floors, aprons etc complete all as specified and directed.

Surface Excavation not exc 30 Cm deep and averaging 15 Cm deep and getting out in soft/loose soils, complete all as specified and as directed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 Sqm on plan and n exc 1.5 m in depth and getting out in soft/loose soils, complete all as specified and directed.

All as per item No.1.06 above, but depth exc 1.5 m and n exc 3.0 m and getting out in hard/dense soils.

M & L for hardcore of gauge not exc 63 mm, deposited, spread and levelled in layers not exceeding 15 Cm thick, watered and rammed to true surface with broken stones complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 Cm in soft/loose soils, complete all as specified and directed.

Removing excavated materials not exc 50 m and depositing where directed at a level not exc 1.50 m above the starting point complete all as Specified and as directed.

Removing excavated material exc. 250 m but n exc.500 m and depositing where directed complete all as specified and directed.

M & L for plain cement concrete (1:3:6) type C-2 using 40 mm graded stone aggregates as in foundation filling, fixing of post holes, support to flag pipe and mass concrete complete all as specified and directed.

M&L for M-25 nominal mix RCC (1:1½:3), type A-1 (using 20mm graded stone aggregate) as in foundations, rafts, footings, foundation beams, plinth beams, base of columns, basement of slabs, underreamed piles and mass concrete etc., complete all as specified and as directed.

M&L for M-25 nominal mix RCC (1:1½:3), type A-1 (using 20mm graded stone aggregate) as in columns, pillars, piers, posts and struts etc., complete all as specified and as directed.

M&L for M-25 nominal mix RCC (1:1½:3), type A-1 (using 20mm graded stone aggregate) as in slabs supported on walls, beams, columns in floors, roofs, landings, Balcones, canopies, duck slabs, shelves and like etc., complete all as specified and as directed.

M&L for M-25 nominal mix RCC (1:1½:3), type A-1 (using 20mm graded stone aggregate) as in beams, cantilevers, bressumbers, lintels, over 1.50m span etc., complete all as specified and as directed.

M & L for extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc completed all as specified and directed.

M&L for plain cement concrete (1:2:4) type B1 using 20 mm graded aggregates in lintels upto 1.5 m clear span, cills, steps, seismic and other similar bands, plinth courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones , bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating including formwork complete all as specified and directed.

M&L for providing precast cement concrete (1:2:4) type B1 using 20 mm graded aggregates set in cement mortar 1:4 as in landings, cover slabs (for manhole etc.) chullah hoods, chajjas, water troughs, shelves and similar articles with plain faces complete all as specified and directed. (NOTE: Reinforcement shall be measured and paid separately)

M&L for mild steel TMT Bars 10 mm dia and over, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including Mild Steel Wire (annealed) not less than 0.90 mm or securing with clips, etc., complete all as specified and as directed.

M&L for mild steel TMT Bars 6-8 mm dia cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including Mild Steel Wire (annealed) not less than 0.90 mm or securing with clips, etc., complete all as specified and as directed.

M&L for mild steel TMT bars 5 mm dia and over upto and including 10 mm dia in stirrups , spacers and binders cut to length , bent to shape required as in reinforcement and binding with MS wire (annealed) not less than 0.90 mm dia complete all as specified and directed .

Use and waste of formwork to sides of concrete foundations, footings, bases of column, raft and raft beams, side and soffit (if any) for foundation and plinth beams etc, vertical or to batter for rough finished surfaces complete all as specified and directed.

Use and waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200 mm thick (horizontal or sloping) for fair finished surfaces complete all as specified and directed.

Use and waste of Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide complete all as specified and directed .

Use and waste of Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc.

Use and waste of formwork to side of pillars, posts, struts, piers, columns for fair finished surfaces complete all as specified and directed.

M&L Brick Work with fly-ash Bricks (with Old Size Bricks), Straight or Curved on Plan exc. 6.0 Metre mean Radius, built in Cement Mortar 1:6, complete all as specified and as directed.

M&L Brick Work with fly-ash Bricks Half-Brick thick, Old Size, built in Cement Mortar 1:4, Straight or Curved on Plan to any Radius, complete all as specified and as directed.

M&L for rendering 15 mm thick built in cement mortar (1:4) on fair faces of brick work or concrete surfaces finished even & smooth (without using extra cement) and mixed with water proofing compound as per manufacturer's instruction complete all as specified and directed. (NOTE : Water proofing compound shall be measured and paid separately).

Supply only liquid water proofing compound all as specified and as directed.

M&L for 10mm thick rendering on fair faces of brick work or concrete surfaces in cement mortar 1:6 finished rendering surfaces even and smooth without using extra cement complete all as specified and directed.

M&L 5mm thick cement plaster on ceiling surfaces finishing even and smooth without using extra cement in cement mortar (1:3) including necessary scaffolding complete all as specified and directed.

M&L for preparation of new plastered surfaces of walls and applying two coats of acrylic distemper over a coat of alkali resistant primer as per manufacturer's instructions complete all as specified and directed.

M&L for preparation of new plastered surfaces of ceilings and applying two coats of acrylic distemper over a coat of alkali resistant primer as per manufacturer's instructions complete all as specified and directed.

M&L for preparation of surfaces and applying two coats of cement base paint over a coat of alkali resistant primer on new plastered surfaces complete all as specified and directed.

M&L for applying two coats of exterior acrylic emulsion weather proof paint over a coat of primer to new wall surfaces of any description, over 10cm width or girth not otherwise described, as per manufacturer's instructions, upto 4 storey height complete all as specified and as directed.

S&F Factory made solid PVC door frame (chowkhat) of size 50mmx47mm made out of 5mm plain colour wood grain PVC sheet used instead of plain colour PVC sheet & edges will be painted to match with printed sheet reinforced with MS square tube, S&F in opening as per specification & drg as per manufacturer instructions complete all as specified and directed.

S&F Factory Made Solid Panel PVC Door Shutter 30mm thick, consisting of frame made out of Mild Steel Tube of 19 Gauge thickness and size of 19mm x 19mm for Stiles and 15mm x 15mm for Top & Bottom Rails. Mild Steel Frame shall have a coat of Steel Primer of Approved Make and Manufacturer. Mild Steel Frame shall be covered with 5.0mm thick heat moulded PVC 'C' Channel of size 30 x 50mm forming Stiles and 5.0mm thick, 75mm wide PVC Sheets For Top Rail, Lock Rail & Bottom Rail on either side, and 10mm (5.0mm x 2) thick, 20mm wide Cross PVC Sheet as gap insert for Top Rail, Lock Rail & Bottom Rail. Panelling of 5.0mm thick PVC Sheet Beading on either side and joined together with Solvent Cement Adhesive, etc. An additional 5.0mm thick PVC Strip of 20mm width is to be stuck on the interior side of the 'C' Channel using PVC Solvent Adhesive, fixing in opening as per Specifications and Drawings shown in MES Schedule Part-II, complete all as specified and as directed.

S&F for 2nd class HW, plain, solid, straight chowkats and frames, wrought, framed, rebated on the solid, moulded or chamfered, put together with glue, pinned at joints complete all as directed.

S&F Factory made 35mm thick with 2nd class hard wood, rail and style factory made plain framed panelled shutter(two panel) with lock, rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail & style as per IS:1003(Part-I) kiln seasoned and chemically pressure treated complete all as specified and directed.

S&F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as directed.

Preparing new surface of wood or wood based material of any description and in any position not otherwise described n.exc 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as directed.

S&F 100mm butt hinges Stainless steel medium weight, complete all as specified and directed.

S&F 75mm butt hinges Stainless steel medium weight, complete all as specified and directed.

S&F 125mm butt hinges mild steel medium weight, cold rolled, complete all as specified and directed.

S&F aluminium handle, cast type anodised 150mm size all as directed.

S&F 200mm aluminium anodised barrel tower bolts of extruded section.

S&F 150mm aluminium anodised barrel tower bolts of extruded section.

S&F 150mm length of cover plate floor door stopper of brass body and tongue with hard drawn steel spring, fixed in floor, complete all as specified and directed.

S&F 300mm aluminium, anodised sliding door bolt with hasp, staple(bolt type) and fixing clip of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy all as directed complete all as directed.

Supply and fixed Steel windows with side hung shutters including box type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded for fixing wire mesh including one shop coat of priming, complete all as specified and directed. (NOTE : Sheet glass for glazing and wire cloth for mosquito proofing shall be measured and paid separately)

Supply and fixed Steel ventilator with top hung shutter including hinges with steel peg stay, complete with and including one shop coat of priming, complete all as specified and directed. (NOTE : Sheet glass for glazing shall be measured and paid separately)

M&L mild steel work in tubular trusses including special shaped washers etc complete using ERW or induction butt welded tubes conforming to IS-1161:2014 grade St-240 complete all as specified and directed. (NOTE: Quoted rates shall be deemed to include for cutting to dead length where required, notching, drilling, fitting, riveting and/or welding or connecting with bolts and nuts (including rivets or bolts and nuts), providing and fitting angle cleats, fish plates, gusset plates etc., also for wedging, plumbing, truing up and fixing complete)

M&L for Mild steel framed works such as grills, gratings etc. with ends of bars shouldered and/or riveted or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walkways, railings, framework of water tanks and similar works conforming to Fe-290 Gde E-165 complete all as specified and directed.

S&F mild steel Collapsible steel gates, top hung, consisting of channel pickets, pivoted flat bars, top and bottom runners, brass handles etc., as specified, erected in position and securing runners with holdfasts and brackets, complete all as specified and directed.

M&L Preparing new Steel or Iron Surfaces of any description, over 10 Cm width or girth and applying Two Coats of Synthetic Enamel Paint over a coat of Red Oxide/ Zinc Chrome Primer, complete all as specified and as directed.

S&F 3 mm thick ordinary quality plain sheet glass and glazing in square n.exc. 0.5 Sqm in each pane complete all as specified and directed.

S&F Aluminium anodised Powder coated for doors, windows, ventilators and partition with one or more rebate (minimum thickness of powder coating 50 micron) and three track with 1.8 mm thick channel section and shutter frame thickness 1.65mm, without sash bars, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc complete all as specified and directed. Notes: 1) Size of window shall be as per site requirement. 2) Glass and wire cloth shall be measured separately.

S&F stainless steel wire cloth of 0.65mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F 5.5 mm thick sheet glass frosted on one side, area in squares exc 0.5 sqm in each pane and glazing with rubber gasket fixed to aluminium frame work / snap beading complete all as specified and as directed by the Engineer-in-Charge

M&L for 19mm thick Prelaminated particle board, exterior grade, prelaminated both side with decorative choice lamination, fixed with rubber packing, anodised aluminium snap beading, screws to aluminium partition wall frame work etc., complete all as specified and directed.

M&L for 18-19mm thick Veneer particle boards, exterior grade, solid core, as in tables, cupboards, drawers, etc., general purpose type, faced with decorative veneer on both faces of type "BB" fixed with screws to timber frame work, complete all as specified and directed.

M&L for IInd class hard wood plain fillets of size exc 3 sqcm n exc 6 sqcm, Square, rectangular or triangular in section, Clean swan, secured with nails or brads, complete all as specified and directed.

S&F 4 lever mild steel type Mortice lock vertical type size 100mm complete all as specified and directed.

S&F 75mm extruded Brass handles, fabricated type, polished bright, fixed with shutters, complete all as specified and directed.

S&F 40mm dia cupboard nobs, fixed with nut, brass screws and washers of bright finished, complete all as specified and directed.

S&F 75mm butt hinges, type C-11, extruded brass, with mild steel hinge pin, bright polished and fixed with shutters, complete all as specified and directed.

S&F Drawer sides length upto 50cm and width 25mm to fixed in drawers with screws, complete all as specified and directed.

S&F 20mm dia fancy type CP drapery rod (as per sample as approved by GE) incl heavy duty decorative bracket and fittings fixed on walls, complete all as specified and directed.

S&F 4.8 mm thick sheet glass frosted on one side, area in squares n exc 0.5 sqm in each pane and glazing with rubber gasket fixed to aluminium frame work / snap beading complete all as specified and as directed by the Engineer-in-Charge

S&F 4.8 mm thick sheet glass frosted on one side, area in squares exc 0.5 sqm in each pane and glazing with rubber gasket fixed to aluminium frame work / snap beading complete all as specified and as directed by the Engineer-in-Charge

M&L for Light shade Vitrified Ceramic coloured tiles (square/ rectangular), 10 mm thick, area of each tile exceeding 0.18 Sqm but not exceeding 0.36 Sqm, set and jointed in neat cement slurry in floors and pointed in white or coloured cement to match the shade of tiles, laid over and including screed bed 20 mm thick in cement mortar (1:6), complete all as specified and directed.

M&L for Dark shade Vitrified Ceramic coloured tiles (square/ rectangular), 10 mm thick, area of each tile exceeding 0.18 Sqm but not exceeding 0.36 Sqm, set and jointed in neat cement slurry in floors and pointed in white or coloured cement to match the shade of tiles, laid over and including screed bed 20 mm thick in cement mortar (1:6), complete all as specified and directed.

All as per item NO.1.74 above, in vertical surfaces like skirtings, dados etc., with and including 10mm thick backing coat in cement mortar (1:3), complete all as specified and directed.

S&F non-skid ceramic coloured tiles (square/ rectangular), 7 to 8 mm thick, area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, set and jointed in neat cement slurry in floors and pointed in white or coloured cement to match the shade of tiles, laid over and including screed bed 20 mm thick in cement mortar 1:6 complete all as specified and directed.

M&L for glazed coloured ceramic tiles in vertical surface 300 X 450 X 7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the colour of tiles, laid over and including 10mm thick screed bed in cement mortar 1:4 complete all as specified and directed.

M&L 25 mm thick PCC (1:2:4) type B-0 (using 12.50mm graded stone aggregate) as in floors, finished even and smooth without using extra cement as directed by the Engr-in-Charge.

M&L 75 mm thick PCC (1:3:6) type C-2 (using 40mm graded crushed stone aggregate) as in plinth protection, finished even and smooth without using extra cement as directed by the Engr-in-Charge.

Removal of existing water proof treatment of any description from roof surface including cement plaster/screed bed carefully from the surfaces, roughening concrete surfaces and cleaning the roof surfaces by brushing, sweeping and scrubbing down with water and removal of debris complete all as specified and as directed.

M&L for Providing Cement Concrete, type B-0, 1:2:4 (using 12.50 mm graded Stone aggregate), as in roof padding, of thickness as required on site, for making good depression/undulation, roof kerb etc, finished even and fair complete all as directed.

M&L 20 mm thick screed bed or bedding layer in cement mortar (1:3) over roof mixed with water proofing compound as per manufacturer's instruction complete all as specified and directed. (NOTE: WPC will be measured and paid separately)

M&L for water proofing treatment on existing cleaned RCC roof with the following specifications and manufacturer's instruction complete all as specified and directed :- (i) Preparing and cleaning of fully dried surfaces as per IS 3067-1966. (ii) Applying bitumen primer conforming to IS:3384-1968 over the cleaned base @ 0.50 litre per sqm. (iii) Providing a layer of 3 mm thick APP modified pre-fabricated five layer, weight not less than 3.6 kg/sqm, black finished reinforced with non-woven polyster matt membrane with butane torch application. Overlap shall be minimum 100 mm on the transverse direction and 75 mm on longitudinal direction. (iv) Applying two coats of bitumen based UV reflective paint with aluminium finish @ 0.10 litre per sqm over APP membrane.

S&F 0.50 mm thick TCT (total coated thickness) pre-coloured galvalume sheets with minimum base metal thickness of 0.45 mm, single skin high rib/multi rib profile galvalume sheeting having 1000-1020 mm width and 28-30 mm high crest @ maximum 250-255 mm pitch (centre) with sheets manufactured out of 0.50 mm this TCT (total coated thickness) high tensile galvalume sheets having tensile strength 550 MPA with 18-20 micron top coat over 5 micron primer and 8-10 micron alkyld backer zinc aluminium alloy AZ-150, sheets having a dip metallic zinc (43.5%0 aluminium (55%) & silicon (1.5%) with total mass coating of 150 gms/sqm on both sides, having wide pans with minimum 3 small stiffening ribs for effective water shedding and special male/female ends with full return legs on laps for purlin support and fixed as per existing profile of roof complete all as specified and directed.

All as per Item No. 1.84 above but 0.50 mm thick coloured plain galvalume sheet as in ridge/valley gutter of roof.

S&F 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall complete all as specified and directed.

S&F 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall complete all as specified and directed.

S&F 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floors, complete all as specified and directed.

S&F 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints, laid in trenches or in floors, complete all as specified and directed.

S&F 110mm bore PVC (SWR) junction single (Single "T") equal or unequal, complete all as specified and directed.

S&F 110mm bore PVC (SWR) bends any radius, complete all as specified and directed.

S&F 75mm bore PVC (SWR) bends any radius, complete all as specified and directed.

S&F 110mm bore PVC (SWR) Vent cowl any radius, complete all as specified and directed.

S&F 75mm bore PVC (SWR) Vent cowl any radius, complete all as specified and directed.

S&F 75mm bore PVC (SWR) floor trap, plain with grating, including jointing with solvent cement, complete all as specified and directed.

S&F 75mm bore PVC (SWR) Gully trap 125/110mm, setting and jointing with solvent cement, complete all as specified and directed.

S&F Vitreous China (coloured) wash down water closet pan (pedestal pattern) with 'P' or 'S' trap front or back inlet, fixing bolts (except flushing cistern and flush pipe) incl plastic water closet seat cover (white) and mild steel chromium plated or aluminium hinging device complete all as specified and directed. (Make : Partyware, Model : Elite / JAQUAR, Model: Continental / CERA, Model: Conventional / HINDWARE, Model: SLICK)

S&F White PVC Flushing Cistern 10 Litre capacity, Low Level Valve Less, Symphonic Action type with Inlet, Ball Valve, Float, flush pipe and Handle including Cutting and pinning in Ends, making good disturbed Surfaces in Cement Mortar 1:3 and fixed including taking down/out unserviceable Flushing Cistern and connected items complete all as specified and directed. (MAKE : PARRYWARE, Model : Slim line Economy / HINDWARE, Model : Sleek Plus / CERA, Model : Corona / PRAYAG, Model: SMART or equivalent model in COMMANDER )

M&L for 18-20 mm thick coloured granite Slab, machine cut, as in vertical surfaces such as skirting, dado, wall cladding etc, fixed over and including 10 mm thick backing layer in cement mortar 1:3, set and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite tiles including rubbing and polishing complete all as specified and directed.

Supply and Fix vitreous China Squatting pan ‘Orissa’ pattern, size 580 X 440 mm, white, with integral foot rests (excluding flushing cistern and flush pipe) including connection to trap and to flushing pipe, etc and including making good to floor, complete all as specified and directed. (MAKE : PARRYWARE, Cat No. C0117 / HINDWARE, Cat No. 20004 / JAQUAR, Cat No. CNS-WHT-OP01 or equivalent model in CERA)

S&F Vitreous China, white, urinal flat back, size of 430 x 370 x 340mm, with grating and union for discharge pipe (excl flush pipe, flushing cistern and waste pipe) incl providing and fixed plugs, bedding urinal against wall in cement mortar 1:2 and securing urinal to plugs with and incl 60mm long brass screws, pointing around urinal back in cement; fixing flushing cistern with brackets, flush pipe, grating and union for discharge pipe complete all as specified and directed. (Make of Urinal : Partyware, Model : Aquaseal N/ CERA, Model: CARYS / HINDWARE, Model: CORTO)

S & F of vitreous China wash basin, white, flat back, size 550x450mm excluding taps, waste, chain and plug and porcelain stopper but including brackets, with 32mm dia Brass Chromium Plated Waste Fitting complete all as specified and directed. (MAKE : PARRYWARE, Cat No. C0406 / HINDWARE, Cat No. 10010 / JAQUAR, Cat No. CNS-WHT-801 / CERA, Cat No: S2040141)

Supplying, fixing, jointing and testing 15mm dia galvanised iron tube, medium grade with all fitting such as union, sockets, tee, angle etc., complete fixed to walls and ceiling or laid in floors, complete all as specified and directed.

Supplying, fixing, jointing and testing 20mm dia galvanised iron tube, medium grade with all fitting such as union, sockets, tee, angle, reducers etc., complete fixed to walls and ceiling or laid in floors, complete all as specified and directed

Supplying, fixing, jointing and testing galvanised iron tube, 25 mm bore, medium grade with all fitting such as union, sockets, tee, angle, reducers etc., complete fixed to walls and ceiling or laid in floors complete all as specified and directed.

Supply, hoisting and fixing rotational moulded polyethylene water storage tank (cylindrical vertical type with closed top) of capacity 1000 Litres, multi-layered (ISI marked), with GI tank nipple & cover, hoisted and fixed in position all as specified in SSR Part-I incl dismantling of existing unsv tank complete all as specified and directed.

Supply and fixing gun metal gate or globe valve, with iron wheel head, screwed both ends for iron pipe and fixed for 20 mm bore pipe complete all as specified and directed.

Supply and fixing gun metal gate or globe valve, with iron wheel head, screwed both ends for iron pipe and fixed for 25 mm bore pipe complete all as specified and directed.

S&F Chromium plated brass Angular stop cock, fancy type, concealed type with wall flange fixed to 15 mm bore iron pipe complete all as specified and directed. (Make : JAQUAR, Cat No: KUP-35053PM / PARRYWARE, Cat No: T3097A1 / CERA, Cat No: F1005201 / PRAYAG, Cat No: 9410 / HINDWARE, Cat No: 320006 )

S&F 20 mm bore Ball brass valves, high pressure, with HDPE float and flynut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and directed. (MAKE : PRAYAG, Cat No. B-152 or equivalent model in JEXON / POLYTUF / SHAKTI)

S&F 15mm bore heavy duty PVC connector pipe of length 450 mm with PTMT coupling at both ends, screwed down for pipe as directed. (MAKE : PRAYAG, Cat No. 323 / POLYTUF, Cat No. 4003 or equivalent model in SHAKTI / JEXON / CERA)

S&F Chromium plated brass Bib cock with wall flange, fancy type, long body, fixed to 15 mm bore of Iron pipe complete all as specified and directed. (Make : JAQUAR, Cat No: CON-107KN/ PARRYWARE, Cat No: G1405A1 / CERA, Model : OCEAN / PRAYAG, Cat No: 9208 /HINDWARE, Cat No: F330041)

S&F Chromium plated brass Pillar tap (premium quality), fancy type. with aerator, fixed to wash hand basin, complete all as specified and directed. (Make : JAQUAR, Cat No: OPP-15001PM / CERA, Cat No: F1005101/ ASIAN PAINTS, Cat No: SRPC101 / HINDWARE, Cat No: F360001 / PRAYAG, Cat No: 8102 or equivalent model in PARRYWARE)

S&F 600mm x 450 mm mirror with PVC frame and fixed to wooden plugs with chromium plated brass screw and cup washers, as in repairs, complete all as specified and directed. (Make: PRAYAG, Cat No: 553 or equivalent model in other makes specified in CA)

Supply and laying 150 mm bore reinforced concrete pipe of Class NP-3, laid and jointed with jute & cement mortar 1:2, complete with collars all specified and as directed.

M&L concrete bed to drain pipe including packing under and haunching against the side of drain pipe after laid and tested in PCC 1:3:6 type C-2 for 150 mm bore pipes complete all as specified and directed.

M&L for cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section ) in cement concrete 1:2:4 type B1 (using 20 mm graded aggregates) smooth finish and reforming benching as required, complete all as specified and directed.

SCHEDULE 'A' PART-II (INT ELECTRIFICATION WORKS) Taking down carefully copper/aluminium point wiring on batten or in PVC conduit or in MS conduit with GI earth wire etc., (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to MES Store for keeping in safe custody for re-use and making good disturbed surfaces of walls, floors, etc complete all as specified and directed.

M&L for concealed type point wiring with 1.50 Sq. mm (nominal area) FRLS-H PVC insulated and unsheathed, multi stranded copper conductor cable 1100 Volts grade, single core, laid in and including PVC conduit complete with all fittings and accessories, fixed to walls/ceiling, including galvanised mild steel terminal boxes 1.25 mm thick conforming to IS-5133 (Part-I) with 3.0 mm thick plastic laminated sheet top cover (ISI Marked) for mounting switches/ regulator /bell push etc and including 1.50 Sq. mm (nominal area) FRLS-H PVC insulated and unsheathed multi stranded copper conductor cable 1100 Volts grade, single core, earth continuity conductor connected to common earth dolly, for one light point /bell point/ ceiling fan/exhaust fan point controlled by one way switch complete all as specified and directed. (NOTES: - (i) Where tube light fitting is to be fitted/suspended, CI Circular boxes shall be provided with the PVC Pipes in the ceiling & the unit rate shall be deemed to be included for the same. (ii) Cost of cutting chases for concealed wiring shall be deemed to be inclusive in the quoted rates. No claim in this regard shall be entertained at a later stage)

All as per item No. 3.02 above but for one 5 amps switch socket outlet on same board controlled by another switch, complete all as specified and directed (concealed type point wiring with terminal box).

All as per item No. 3.03 above but for one 5 amps switch socket combination on independent board, complete all as specified and directed (concealed type point wiring with terminal box).

All as per item No. 3.04 above but using 2.5 sqmm single core multi stranded copper conductor FRLS-H PVC insulated and unsheathed, cable for 3/6 pin 15 Amp socket outlet controlled by one switch on independent board with and incl 2.5 sqmm green FRLS-H PVC insulated and unsheathed, copper conductor as continuous earth wire with lugs complete all as specified and directed (concealed type point wiring with terminal box).

S&F switch piano flush button AC 230 V Single pole 5/6 Amp one way complete all as specified and directed.

S&F socket outlet, non-shuttered, 2-in-1, 3 pin, 6 Amp AC 230 Volts flush type complete all as specified and directed.

S&F switch socket combination, 5 pin, 6 Amp AC 230 Volts flush type complete all as specified and directed.

S&F switch piano flush button AC 230 V Single pole 15/16 Amp one way complete all as specified and directed.

S&F switch socket combination 2 in 1, 3 pin, 6 and 16 Amps flush type universal complete with all necessary electrical connection all as specified and directed.

S&F stepped type electronic fan regulator, flush type, 100 watts, 5 Speed Control, 230/240 Volts complete all as specified and directed.

S&F ceiling rose surface, polycarbonate/bakelite, three terminals complete all as specified and directed.

Taking down of old Submain wiring any type including batten/ conduit/ casing at any indicated situation complete all as specified and directed.

S&F sub main wiring with 2 runs of single core FRLSH PVC insulated & unsheathed multistranded copper conductor of nominal cross sectional area 6.0 Sqmm alongwith one run of FRLSH PVC insulated & unsheathed multistranded copper conductor of nominal cross sectional area 6.0 Sqmm as earth continuity conductor drawn through and including concealed PVC conduit of suitable size complete all as specified and directed. (NOTE : Three runs of single core 6.0 Sqmm cable & one run of PVC conduit shall be measured as one unit)

S&F sub main wiring with 2 runs of single core FRLSH PVC insulated & unsheathed multistranded copper conductor of nominal cross sectional area 4.0 Sqmm alongwith one run of FRLSH PVC insulated & unsheathed multistranded copper conductor of nominal cross sectional area 4.0 Sqmm as earth continuity conductor drawn through and including concealed PVC conduit of suitable size complete all as specified and directed. (NOTE : Three runs of single core 4.0 Sqmm cable & one run of PVC conduit shall be measured as one unit)

Taking down of Old MCB DB any type any size including MCCB/RCCB/MCBs and disconnecting the serviceable MCBs and keeping in safe custody for reuse at site or removal from site complete all as specified and directed.

Supply and fixing TPN DB, IP 43 protection, double door (premium quality), 415 volts, 4 way (8+12), with 100 Amps copper bus bar for each phase complete all as specified and directed. (MAKE : L&T, Cat No. DBTPN004DD / LEGRAND, Cat No: 507670 / SCHNEIDER, Cat No. A9HTND04 / ABB, Cat No: E-SHDB M4 / PANASONIC, Cat No: BQS 304H / HAGER, Cat No: VYT04DH)

S&F Double Door, Sheet Metal Enclosure for DBs (Premium range), for mounting of MCB for 240 Volts, 8 way, with 100 Amps rated copper bus bar, Single Pole & Neutral, complete all as specified and directed.

S&F Double Door, Sheet Metal Enclosure for DBs (Premium range), for mounting of MCB for 240 Volts, 4 way, with 100 Amps rated copper bus bar, Single Pole & Neutral, complete all as specified and directed.

NOTE FOR ITEM NO. 3.17 to 3.19 :- (1) Incoming MCCB/RCCB/MCB and outgoing MCBs shall be measured and paid separately as "Supply Only". (2) Quoted rate is deemed to be inclusive of blanking plate for slots remaining blank after fixing of MCBs. (3) DB, MCCB, RCCB & MCB shall be of the same manufacturer.

S&F MCB (premium quality), 'C' series, TPN, 415 volts, 63 Amps, breaking capacity 10KA complete all as specified and directed. (MAKE : L&T / LEGRAND / SCHNEIDER / ABB / PANASONIC / HAGER)

S&F MCB (premium range), 'C' series, SPN, 32 Amps, breaking capacity 10KA complete all as specified and directed.

S&F MCB (Premium Range), 'C' series, single pole, 6 to 32 Amps, breaking capacity 10KA complete all as specified and directed.

S&F MODULAR MCB protected power unit with one 25 Amps socket with 3 pin plug top and including 01 No MCB, DP, and starter 25 Amps ratings with six module plate and flush metal GI box and electrically connected, as in repairs, complete all as specified and directed. (MAKE : HAVELLS, Cat No. DHDUCDP0253025 / NORTH WEST, Cat No: ACPU6M-BT or equivalent model in ABB / CRABTREE / HAGER / SCHNEIDER / LEGRAND) (NOTE : Enclosure & MCB shall be same manufacturer. Cost of MCB is deemed to be included in the quoted rate)

S&F surface mounted LED luminaire, 1 X 20 Watt in aluminium housing, operating voltage 180-270 V, with acrylic/polycarbonate diffuser & integrated constant current electronic driver complete with all other accessories internally prewired and including connecting up with three core flexible copper wire of suitable size complete all as specified and directed. complying with the following specifications:- (a) minimum efficacy 110 lumen/watt (b) CRI not less than 80, (c) THD < 20% (c) having in built short circuit and surge protection (d) colour temperature not less than 5700 degree K (e) life not less than 25000 hours of operation

S&F recess mounted LED luminaire, of size 600 mm x 600 mm, in powder coated CRCA housing , having glare free diffuser, operating voltage 180-270V, with constant current electronic driver complete with all accessories with and including 35/36 Watt LED and including all accessories, mounting frame etc and connecting up with three core flexible copper conductor wire of adequate size complete all as specified and directed and complying with the following specifications:- (a) minimum efficacy 110 lumen/watt (b) CRI not less than 80, (c) THD < 20% (c) having in built short circuit and surge protection (d) colour temperature not less than 5700 degree K (e) life not less than 25000 hours of operation (f) Weather protection: IP20

Supply and Hanging, ceiling fan, with brushless DC motor, 1200 mm sweep without remote, down rod, canopy, fan blades and accessories and connecting up including provision of PVC insulated, sheathed round flexible wire with multi stranded copper conductor of size 1.0 Sq mm, 3 core, 1100 Volts grade, from ceiling rose/ connector to fan including dismantling existing fan complete all as specified and directed. (MAKE : USHA, Model: TECHNOAIR / CROMPTON GREAVES, Model : ENERGION HS / ORIENT, Model: ECOTECH or equivalent model in BAJAJ / HAVELLS) NOTE: Old fan shall be deposited by contractor in MES store yard

Supply and fix Air Circulator wall fan 450mm sweep, complete with all accessories 230 Volts copper winding rotational type and connecting up including provision of PVC insulated, sheathed round flexible wire with multi stranded copper conductor of size 1.0 Sqmm, 3 core, 1100 Volts grade, from ceiling rose/ connector to fan, complete all as specified and directed. (MAKE : USHA / CROMPTON GREAVES / ORIENT / BAJAJ / HAVELLS)

M&L for earthing complete with galvanized steel earth plate electrode 600 mm x 600 mm x 6.0 mm thick buried directly in ground vertically to a depth not less than 2.25 meter deep below ground level with top edge earth plate at a depth not less than 1.5M below normal ground level connected to galvanized steel earth wire 4 mm dia (upto 7.5 metres) by means of bolts, nuts check nuts and washers of galvanized steel and connected to main switch board or main control board as directed and including provision of concrete pit in PCC (1:3:6) type C1, pre-cast RCC (1:2:4) type B1 cover slab 45 cm x 45 cm x 5 cm reinforced with 8 mm dia. TMT bars @ 150 mm centre to centre both ways, with one handle for lifting made out of 8 mm dia MS bar, provision of funnel, wire mesh, 20 mm bore galvanized steel tubing (Medium grade) for watering, charcoal or coke and salt in alternate layers, 40 mm bore galvanized steel tubing medium grade for protection of earth lead connection, necessary excavation and earth work in any type of soil and including necessary testing complete all as shown in Figure 15A of IS 3043 :1987, complete all as specified and directed.

SCHEDULE 'A' PART-III (EXT ELECTRIFICATION WORKS) S&F Air termination, single pointed copper rod, 12 mm dia and 300 mm long, fixed on GI pipes with earthing strips for earth conductivity to ground, as in repairs, complete all as specified and directed. (NOTE: GI pipe & earthing strip shall be measured and paid separately)

S&F Test point terminal block, made of gun metal or phosphorous bonze of size 75 mm X 75 mm X 25mm, drilled and screwed including 3 Nos, 8 mm dia and 25 mm long hex screws, as in repairs, complete all as specified and directed.

S&F Junction box made out of 2 mm thick mild steel CRCA sheet including applying two coats of synthetic enamel paint over a coat of red oxide primer, duly spray painted, of size not less than 20cm X 20cm X 15cm with locking arrangements and provision of earthing strip entry and exit, fixed on walls with GI bolts, nuts and washers (of suitable size), as in repairs, complete all as specified and directed.

S&F galvanised iron strip 32 mm X 6 mm with saddles and fixing screws etc, for roof conductors and down conductors above ground, fixed on porcelain insulator @ 1.0 m spacing complete all as specified and directed. (Note: Porcelain insulators will be measured and paid separately)

S&F porcelain insulators of size 50 mm with fixing arrangements complete all as specified and directed.

S&F GI tubing 50 mm bore, medium grade, laid in trenches/floors or fixed along poles/walls for cable/earth strip protection, fixed with proper size clamps, nuts & bolts or for fixing lightning conductors etc., as in repairs, complete all as specified and directed.

M&L for earthing complete with copper earth plate electrode 600 mm x 600 mm x 3.15 mm thick buried directly in ground vertically to a depth not less than 2.25 meter deep below ground level with top edge earth plate at a depth not less than 1.5M below normal ground level connected to copper strip 32 X 6 mm (upto 7.5 metres) by means of bolts, nuts check nuts and washers of galvanized steel and connected to main switch board or main control board as directed and including provision of concrete pit in PCC (1:3:6) type C1, pre-cast RCC (1:2:4) type B1 cover slab 45 cm x 45 cm x 5 cm reinforced with 8 mm dia. TMT bars @ 150 mm centre to centre both ways, with one handle for lifting made out of 8 mm dia MS bar, provision of funnel, wire mesh, 20 mm bore galvanized steel tubing (Medium grade) for watering, charcoal or coke and salt in alternate layers, 40 mm bore galvanized steel tubing medium grade for protection of earth lead connection, necessary excavation and earth work in any type of soil and including necessary testing complete all as shown in Figure 15A of IS 3043 :1987, complete all as specified and directed.

Demolition of concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed.

M&L for PCC (1:2:4) type B-1 using 20 mm graded crushed stone aggregate as in coping of poles / pipes / strip alignment etc using necessary formwork and finishing the exposed surfaces even and smooth without using extra cement, complete all as specified and directed.

M&L for precast PCC (1:2:4) type B-1 using 20 mm graded crushed stone aggregate as in base of eathing strip, set in cement mortar 1:4 complete all as specified and directed.

MS JYOTI INDUSTRIES

MODERN AGENCY

M/S L.R.ENTERPRISES

MARUTI ENTERPRISES

MS HORIZEN

JAY MA TARA TRADERS

KWALITY CONSTRUCTION

M A ENTERPRISES