Construction of Emporium building and Temporary Shade for Vegetable Vendors in Civil Surgeon Campus Godda.

Amount

E/W in exacavation in foundation trenches in ordinary soil and disposal of excavated earth as obtained to a distance up to 50 M includind all lifts, levelling, ramming the foundation trenches, removing roots of trees,shurbs all completes as per approved design,building specification and direction of E/I.

Providing coarse clean sand in filling in foundation trenches or in plinth including ramming and wateringn in layers not exceeding 150 mm thik with all leads and lifts including cost of all materials, labour, royality and taxes all complete as per building specification and direction of E/I.

Earth filling in foundation trenches and plinth in layers not exceeding 150 mm. thick well watered, rammed, fully compacted and fine dressed with earth obtained from excavation of foundation frenches within a lead of 50 M. and lift of 1.5 M all complete as per building specification and direction of E/l (Mode of measurement compacted volume).

Providing designation 75B, one on B/F solling joints filled with local sand including cost of watering taxes royality, all complete as per building specification and direction of E/I.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work up to plinth level :

1:2:4 ( 1 cement : 2 coarase sand (zone-III) : 4 graded stone aggregate 20 mm nominal size)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work up to plinth level :

1:1.5:3 (1 cement : 1.5 coarase sand (zone-III) : 3 graded stone aggregate 20 mm nominal size)

Reinforcement cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering , shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarase sand (zone-III) : 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15 landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircase and spiral stair cases above plinth level up to floor five level, excluding the cost of centring, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement : 1.5 coarase sand (zone-III) : 3 graded stone aggregate 20 mm nominal size)

Providing designation 75B brick work in C.M (1:6) in foundation and plinth with approved quality of clean coarse sand of F.M 2 to 2.5 including approved 10mm thick mortar joints , cost of screening materials raking out joints to 15mm depth , curing , taxes and royalty all complete as per building specifition and direction of E/I.

Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (1 cement : 2 coarase sand (zone-III) : 4 graded stone aggregate 20 mm nominal size)

Providing designation 75B brick work in C.M (1:6) in superstructure with approved quality of clean coarse sand of F.M 2 to 2.5 including approved 10mm thick mortar joints , cost of screening materials raking out joints to 15mm depth , curing , taxes and royalty all complete as per building specifition and direction of E/I.

Providing designation 125 mm thick reinforced designation 75 A brick work in C.M (1:4) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including the cost of screening, carriage of materials , scafolding, raking out joints to 15 mm depth, curing, taxes and royalty ( but excluding the cost of reinforcement) all complete as per building specification and direction of E/l.

Providing Tor steel reinforcement of 10 mm, 12 mm and 16 mm dia bars as per approved design and drawing excluding carriage of bars to work site, C/B/B with annealed wire with cost of wire, removal of rust, placing the rods in position all complete as per building specification and direction of E/I.

Providing 19 mm thick W.P.C. Plaster (1:3) With clean coarse sand of F.M- 1.5 with 5% cico or any other approved water proofing compound including curing carriage of water with all leads and lifts as per building specification and direction of E/I.

Providing 12 mm tick Cement Plaster (1:6) With clean coarse sand of F.M- 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I.

Providing 1.5 mm cement punning including curing, carriage of water with all leads and lifts as per building specification and direction of E/l.

Providing 6 mm thick Cement Plaster (1:4) in ceiling With with clean coarse sand of F.M- 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I.

S/F/F M.S grill made of 20x6mm M.S flat as per approved design and drawing, properly fabricated with joints continues filled welded and fineshed smooth, carrige of grill to work site hoisting as per building specification and direction of E/I.

Suppliying, fitting and fixing callapsible gate of approved size and make rpopoerly fabricated with vertical double channels 20x10x2mm at 100mm centres and braced with M.S flat diagonals 20x3mm with top and bottom rails of T iron 40x40x6mm with 30mm dia, steel pulleys complete with bolts, nuts locking arrrangements, stoppers, handls, including applying a priming coat or red lead paints, car riage, hoisting and taxes all complete as per building specification and direction of E/I.

Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double action hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-incharge (Door handle, lock and stopper etc.to be paid separately).

Providing and fixing double glazed hermetically sealed glazing/6mm th ACP panel in aluminium windows, ventilators and partition etc. with 6 mm thick clear float glass both side, having 12 mm air gap, including providing EPDM gasket, perforated aluminium spacers, desiccants, sealant (Both primary and secondary sealant) etc. as per specifications, drawings and direction of Engineer-in-charge complete.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work up to plinth level :

80x1.25 mm M.S. laths with 1.25 mm thick top cover

25 mm thick PVC flush door shutters made out of a one piece multi chamber extruded PVC section of the size of 762 mm x 25 mm or less as per requirement with an average wall thickness of 1 mm (± 0.3 mm). PVC foam end cap of size 23 x 10 mm are provided on both vertical edges to ensure the overall thickness of 25 mm. M.S. tube having dimensions 19 mm x 19 mm and 1.0 mm (± 0.1 mm) is inserted along the hinge side of the door. Core of the door shutter should be filled with High Density Polyurethane foam. The Top & Bottom edges of the shutter are covered with an end-cap of the size 25 mm x 11 mm. Door shutter shall be reinforced with special polymeric reinforcements as per manufacturer’s specification and direction of Engineer-in-charge to take up necessary hardware and fixtures. Stickers indicating the locations of hardware will be pasted at appropriate places

Providing and fixing factory made door frame (single rebate) made out of single piece extruded solid PVC foam profile with homogenous fine cellular structure having smooth outer integral skin having 62 mm width & 32 mm thickness, frame will be mitred & Jointed with self driven self tapping screws of size 38 mm x 4 mm & PVC solvent cement , including fixing the frame to wall with suitable dia & length anchor fastener as per manufacturer’s specification and direction of Engineer-in-charge.

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Providing two coats of oil bound distemper of approved shade and make over a coat of cement primer on new surface including repairing the plastered surface smooth with sand paper, scaffolding, washing of floors and taxes, all complete as per building specification and direction of E/l.

Providing two coats of snowcem of approved shade and over a coat of cement primer on new surface including repairing the plastered surface smooth with sand paper , scaffolding, curing and taxes all complete as per building specification and direction of E/I.

Providing two coats of synthetic enamel paint of approved shade and make over steel surface including cleaning the surface thoroughly, scaffolding and taxes all complete as per building specification and direction of E/l.

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete.

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick bed of cement mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sq.m including pointing the joints with white cement and matching pigments etc., complete.

Providing and laying 6mm precast white glazed tiles in walls over 12mm cement mortar (1:3) and jointed with grey cement slurry flush pointed with white cement including rubbing, polishing and cost of curing, taxes and royalty all complete as per building specification and direciton of E/l. With "A" grade white 15x15 cm. Tiles

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Area of slab over 0.50 sqm

Material & labour for Clading of ACP( aluminium composite panel of 4 mm Thick of approved brand & Colour fixed over alminium framing and jointed with silicon gasket properlly all complete design and drawing & Carriages as per direction of E/I

Providing and laying 75 mm thick compacted bed of dry brick aggregate of 40 mm thick nominal size including spreading, well ramming, consolidating and grouting with jamuna sand, including finishing smooth etc. complete as per direction of Engineer-in-charge.

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone - III) : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.

Providing 250mm. wide brick drain in cement mortar (1:6) with av. 250mm. clear depth and 250mm. apron including cost of earthwork involved with 75 mm. ~ cement concrete (1:4:8) over one brick designation 75A flat soling in proper grade and slope at the base, the drain duly plastered in C.M.(1:3) with punning over exposed surface all complete as per building specification and direction of E/l.

Centering and shuttering including strutting propping etc

Carriage of Materials from quarry site to work site.

Stone chips

Bricks

Wiring for fan point / light point / exhaust fan point/ call bell point with 1.5 sq. mm FR PVC insulated copper conductor in recessed conduit.

Wiring for light/power plug with 2 x 4 sq.mm FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit, along with 1 No 4 sq.mm FR PVC insulated copper conductor single core cable for loop earthing etc as required.

Wiring for circuit/ submain wiring along with earh wire with the following sizes of FR PVC insulated copper conductor single core cable in surface / recessed PVC conduit as required

2 x 1.5 Sq mm + 1 x 1.5 sq mm earth wire

2 x 2.5 sq mm + 1 x 1.5 sq mm earth wire

2 x 4.0 sq mm + 1 x 4.0 sq mm earth wire

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

12 way single door

S/F of following , following 240 volts, 'C' series, miniature circuit breaker suitable for inductive load of following pole in the existing MCB DB complete with connections, esting and commissioning etc. as required.

6/32 amps, Single pole

Supplying and fixing following rating, double pole, 240 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing 2 pin 5 amp. Ceiling rose on the existing junction box/ wooen block including connection etc. as required .

Supplying and fixing Batten / Angle holder including connection etc as required .

Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq.mm FR PVC insulated, copper conductor, single core cable etc. as required.

Supplying 48" dia. Sweep celling fan with eloctronic regulator of any ISI make including connection with 1.5sq.mm. Copper wire drawn of the roof including taxes, carriage to worksite etc. all complete job.

Supplying & fixing of holder type LED 15W bulb of any ISI make including taxes, carriage to worksite etc. complete job.

Earthing with coper earth plate 600 x 600m x 3mm thickness including accessories and providing masonry encloser with cover plate having locking arrangement and watering pipe etc. as required (but without choracal of coke and solt.)

Providing and laying 6SWG copper wire at 0.50 metre below ground level for conductor earth electrode, including soldering etc. as required.

Suppolying and fixing metal box of the following sizes in recesses with suitable size of pohonic laminated sheet cover front including painting etc. as required.

210 mm x 206 mm x 48 mm(10"X12")

170 mm x 221 mm x 48 mm(8"X10")

75 mm x 75 mm x 50 mm (4"X4")

Supplying and fixing following piano type switch/ socket on the existing switch box/ cover including connections etc. as required.

5/6 A switch

3 pin 5/6 A socket outlet

15/16 A amp switch

15/16 A socket outlet

Supplying fitting vitrous white glazed earthen ware I.W.C. of approved make with 100 mm H.C.I. "P" trap 15 liters C.I. Pull and let go flushing cistern of approved make complete with all fiting C.I. Or CC Brackets 32 mm alkathene/PVC telescopic Flush, pipe about 2 M long with one brass coupling and clamps G.I. body brass spindle stopper cock of weight not less than 50 gms, 15 mm PVC connection pipe 450 mm long and the exposed pipe and cistem with who coat of approved paint over a coat of red oxide primer etc. all complete as per specification and direction of E.I. with 12.5 ltr. low level PVC cistem.All complete as per building specification and direction of E/I.

supplying fitting and fixing flat back or angular lipped front vitreous white glazed earthen ware urinal or approved ISS make with all fittings with C.I or R.S brackets standard size G.I flush pipe with fitting flames 15 mm C.I body bras spindle stop cock of approved quality weight not less the 400gms 15mm PVC/alkathene pipe 450mm long with bras coupling at both ends and doing plumber points including painting to exposed part with two coat of approved paint over a priming coat of red oxide cutting wall and floor making good the same etc, all complete as. per specification and direction of E/ I . Flat black (800x350mm)

Providing and fixing wash basin with C.I / M.S brackets 15mm C.P. bars pillar tap kingstone / Gem/ techno / ponce 2mm C.P brass based of standard poattem, including painting and fitting of brackets , cutting and making good the wall wherever require- Flat back wash basin size 550x400mm with single 15mm C.P. Brass pillar tap.

Provign and fixing C.P barass bib cock of approved quality conforming to IS 8931, 15mm dia nominal bore of approved brand C.P. Fitting .

Proving and fixing PTMT extension nipple 15mm size with 12"BSP thered 70mm length abd 300 bredth and weighing not less than 18gms of approved make.

Supplying, fitting gum metal full way value of approved quality all complete as per specification and direction of E/I 15mm dia 25mm dia 32mm dia

25 mm dia

Providing and fixing brass stop cock of approved qualty all complete as per specification and direction of E/ I.

15 mm dia

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.

20 mm nominal outer dia Pipes

25 mm nominal outer dia Pipes

Cutting Chajja of concrete for laying G.I pipe and restoring the same with RCC (1:2:4) brick work in cement mortar (1:4) and cement polaster (1:4) as per apecification and direction of E/ I

Making holes in walls for GI pipe and restoring the same all cost complete.

125 mm thick wall

250 mm thick wall

Providing and fixing on wall face unplasticised Rigid PVC pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.

75 mm dia

110 mm dia

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.

Single tee with door 75x75x75 mm

Single tee with door 110x110x110 mm

Bend 75 mm dia

Bend 110 mm dia

Supplying and fixing H.C.I, fittings of approved make confirming to I.S.S. 1729 including supplying nails and bobins lead and yarn for making lead chaulked joints including earth work or providing scaffolding as the case may be all complete as per specification and direction of E/l.

Floor trap with grating 100 mm dia

Norton patent H.C.I Coel 100 mm dia

Supplying, fitting and fixing the following items with all materials as per specification and direction of E/I.

Mirrors of 6 mm thick plate glass bevelled edge mirror including brss revolving fittings 3 mm plywood board and C.P. hinges to fix with mirror (600x450 mm size).

C.P. brass towell rail 20mmx600mm with bracket container

C.P. brass dish container medium quality with screw and hinges etc.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank

Cutting drain width wise about GL for laying PVC pipe and restoring brick work in cement mortar 1:4 12mmcement palster in C.M (1:4) with neat cement punning as per spe3cification and direction of E / I

Making holes in walls for Laying PVC pipes and restoring the same all cost complete. 125 mm

Supplying all tolls and labour and cutting chajja comice for laying PVC pipes and good the as poer specification and direction of E / I

Extra for earthwork in hard soil as per specification and direction of E/l (vide classification of soil item-B)

Providing 12 mm cement plaster (1:3) with clean coarse sand FM 1.5 with floating coat of neat cement on skirting rounding all complete as per specification.

Providing 12mm cement plaster (1:3) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/l.

Providing Tor steel reinforcement of 10mm. ,12mm & 16mm dia. bars as per approved design and drawing excluding carriage of M.S. bars to work site , cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction of E/l.

Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design.

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Construction of 200/165 mm X 250 Mtr deep bore well in all kinds of soil and rock in rural or any other area for installation of pump set with Hydraulic DTH Rig Machine all complete including supplying all materials tools drilling rig and air compressor and equipments as well as fuel lubricants and cost of transportation of Rig Machine and other vehicle upto the site including cost of flushing charges Geological Investigation etc all complete job.

(i) From 0 to 50 Mtr

(ii) From 51 to 75 Mtr

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge. 200mm nominal size dia

Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by "V" notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge

Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of: 200mm dia

Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete. 200mm dia

Supplying 100mm dia Submersibe pump set conforming to I.S: 8034 and motor conforming to I.S:9283. Pump shall be suitable for various delivery head and discharge with stainless steel pump shaft and polypropylene/noryl impeller. Motor suitable for working on 415V+10%, 3PH, 50Hz, A.C. Supply with cable guard, thrust carbon/fiber bearing to with stand entire hydraulic thrust, water proof winding shall be provided. The pump set shall be suitable for direct coupling. Pump shall have suitable outlet as per manufacturers design. Anti thrust stream lined non return valve shall be provided with pump. 3 meter submersible copper conductor cable in single/double run shall be provided with each pump. Submersible Pump set 100mm dia 9with Polypropylene/Noryl/Impeller) upto 20 stages. 2 HP

Supply fitting & Fixing of standard make starter pannel board with arrangement of all necessary protection including all taxes, royalty etc all complete job as per direction of E/I.

Supplying fitting and fixing 3 core 4 sq.mm flat copper submersible cable FINOLEX/HEVELS make including all taxes, royalty etc all complete job as per direction of E/I.

Supply fittings and fixing lowering 50mm dia collumn pipe -do-do- all complete job as per direction of E/I.

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete

Supplying G.C.I. sheet confirming to I.S. 227 including allincluding carriage to worksite and taxes all complete job as per builing specification and direction of E/I. (thickness 0.63 mm)

Labour for Fittng and fixing G.C.I or C.A Sheet roofing in proper slope including the cost of J or L hooks , Limpet and Bitumen washers, carriage of sheets to work site and taxes all complete as per builing specification and direction of E/I.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work up to plinth level : 1:1.5:3 ( 1 cement : 1.5 coarase sand (zone-III) : 3 graded stone aggregate 20 mm nominal size)

Add 12% GST (In Basic Rate must fill 0.12)

Add 1% Labour cess (In Basic Rate must fill 0.01)

JAMIL PARWAIZ