PROVISION OF VIEW CUTTER TOWARDS NYAY MARG AT HOSTING ROAD, URINALS ALONG WITH WC BEHIND MANOJ PANDEY HALL AND CERTAIN OTHERS REV WORKS AND MINOR WORKS AT NEW CANT UNDER GE (WEST) ALLAHABAD

Amount

Excavation in trenches in soft/loose soil not exceeding 1.5 metre wide & not exceeding 1.5 metre depth for foundation etc and getting out, complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers n.exc. 25 cm in soft/loose soil complete all as specified and directed.

Filling under floor using excavated soil, spreading and levelling in layers n exc. 25 cm thick well ramming in layers and watering etc complete all as specified and directed.

M/L PCC type D-2 1:4:8 (40 mm graded aggregate) as in foundation filling, sub base and mass concrete complete all as specified and directed.

M&L RCC M-25 design mix as in beams, cantilevers, lintels over 1.5m span etc complete all as specified and directed.

M&L RCC M-25 design mix as in foundation, footing, base of col, beam, lintel ,plinth beam, bases for column etc complete all as specified and directed.

M&L RCC M-25 design mix for columns and etc complete all as specified and directed.

M&L RCC M-25 design mix for slab and chajjas etc complete all as specified and directed.

M&L for use and waste form work to sides of concrete foundation, footing, bases of columns and similar works in vertical or to batter of fair finished surfaces complete all as specified and directed.

M&L for use and waste form work to sides of concrete columns and similar works in vertical or to batter of fair finished surfaces complete all as specified and directed.

M&L for use and waste form work to soffits of suspended slabs such as roof slabs, floor slabs, landings, Chhajja, and similar work n. exc. 200 mm thick, rough finished surface of complete all as specified and directed.

M&L for use and waste form work to sides of concrete beam, side and soffits of plinth beam and similar works or to batter of fair finished surfaces complete all as specified and directed.

M&L for brick work with with fly ash bricks bricks old size straight or curved on plan exceeding 6 metre mean radius built in CM 1:6 complete all as specified and directed.

S&F mild steel TMT bar 10 mm dia and over, cut to length, bent to shape required including cranking, bending, spirally for hooping for foundations, columns, beams and slabs hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clip complete all as specified and directed.

S&F mild steel TMT bar 8mm dia, cut to length, bent to shape required including cranking, bending, spirally for hooping for foundations, columns, beams and slabs hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clip complete all as specified and directed.

S&F mild steel TMT bar 8 mm dia, cut to length, bent to shape required including cranking, bending, spirally for hooping for stirrups hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clip complete all as specified and directed.

M&L for rendering 15mm thick in CM 1:6 on fair faces and of brick work or concrete surface finishing the surface even and smooth without extra cement complete all as specified and directed.

M&L for 15 mm thick rendering on fair faces of brick work or concrete surface in cement mortar 1:4 mixed with water proofing compound, finished even and smooth without using extra cement complete all as specified and directed. Note:- Water proofing compound shall be measured and paid separately as supply only.

M&L for rendering 5mm thick in CM 1:4 on ceiling surface and finishing the surface even and smooth without extra cement complete all as specified and directed.

Supply only integral liquid water proofing compound complete all as specified and directed. Make:- Dr Fixit Pidiproof LW+ or equivalent in specified make.

M&L for non skid ceramic coloured joint free tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11sqm but not exc 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile complete all as specified and directed.

M&L for joint free glazed ceramic coloured tiles 450x300x7mm thick for work on vertical surface such as skirting, dado, set & jointed in cement slurry and pointed in white or coloured cement to match the shade of tile complete all as specified and directed.

M&L for screed bed or bedding layer in CM 1:6, 15mm thick complete all as specified and directed.

M&L for rendering 10mm thick on fair faces of wall or concrete surfaces in CM 1:4 finished rough for wall tiling complete all as specified and directed.

M&L for 75mm thick PCC 1:4:8 type D-2 using 40mm graded stone aggregate as in sub base of floor complete all as specified and directed.

M&L for hard core of broken stone or boulders of gauge n.exc 63 mm deposited spread and leveled in layers n.exc 15 cm thick watered and rammed to a true surface complete all as specified and directed.

M&L for 75mm thick PCC (1:3:6) type C-2 using 40mm graded mechanically crushed stone aggregate as in plinth protection finished even and smooth without using extra cement with & including 10mm wide, 30mm deep joints at the rate of 3.00 mt centre to centre and at every turning & filling the joints with bitumen & sand mixture complete all as directed.

M&L for preparation of newly plastered surfaces of wall and applying two coats of cement base paint complete all as specified and directed.

M&L for preparation new plastered surface of wall and applying two coat of oil bound distemper and a coat of primer over a coat of 1mm thick Birla putty as base coat complete all as specified and directed.

M&L for preparation of new surfaces and applying three coat of white wash on ceiling complete all as specified and directed.

S&F Factory made solid PVC Chowkhat /Door frame of size 50x47 mm with a wall thickness of 5 mm, made out of extruded 5 mm thick rigid PVC foam sheet coloured, reinforced with 19x19mm MS square tube of 19 gauge including rubber gasket, PVC fasteners, screws, brackets as per SSR Part-II (2020) complete all as specified and directed.

S&F solid panel PVC door shutter factory made solid PVC moulded door shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick 3D wood grain moulded PVC sheet polyurethane painted on the front face & 2mm plain colour PVC Sheet on back face, with particle board core supplying & fixing in frame at site as per specification & drawing complete all as specified and directed.

S&F 100mm long type stainless steel, Butt hinges, with galvanized mild steel hinge pin, anodised complete all as specified and directed.

S&F aluminum handle fabricated type anodized size 150 mm long, complete all as specified and directed.

S&F aluminimum anolised barrel tower bolt of extruded section 200mm long, complete all as specified and directed.

S&F GI tubing, 15 mm bore 'medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and directed.

S&F GI tubing, 20mm bore 'medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and directed.

S&F 500 ltrs capacity rotational moulded polyethlene water storage tank (cylindrical vertical with closed top) hoisted and fixed in position complete all as specified and directed.

S&F ball valves, high pressure, with polythene float and fly nut complete, screwed for iron pipe 20mm bore or brass ferrule complete all as specified and directed.

S&F gun-metal 20mm bore, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

S&F bib tap 15mm bore, chromium plated fancy type with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed, complete all as specified and directed.

S&F stop valve 15mm bore, chromium plated fancy type, with long shank and cup screwed down, high pressure, with crutch of butterfly handle, screwed both ends for iron pipes or for unions complete all as specified and directed.

S&F low level flushing cistern PVC 10 ltrs capacity with all internal fittings, bracket and 32mm bore PVC flush pipe, complete all as specified and directed.

S&F PVC connections 15 mm size with PTMT nuts of length 600mm complete all as specified and directed.

S&F 15mm bore dia of pipe pillar taps cast copper alloy with capstan heads, chromium plated screwed down high pressure with or without lettered hot or cold with long screwed shanks and fly nuts screwed for iron pipe complete all as specified and directed.

S&F vitreous china wash down water closet pan (padestal pattern) white excluding flushing cistern & flush pipe including plastic water closet seat cover closed pattern with flat bottom and cover and MS chromium plated aluminised hinging device including connection to trap drain pipe or outgoing pipes and to flushing pipe anti syphonage pipe etc. complete all as specified and directed.

S&F steel ventilator with top hung shutter including hinges, steel peg stay, complete all as specified and directed.

M&L for preparation of new or previously untreated surfaces of steel of any description, over 10cm in width or girth and apply two coat of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L for 3mm thick figured glass, pin head type and glazing with oil putty / beads in square, area n.exc 0.5 sqm in each pane complete all as specified and directed.

S&F PVC (SWR) 110mm pipes single socketed in any length with rubber ring joints laid in trench or floor complete all as specified and directed.

S&F PVC (SWR) pipes 110mm single socketed in any length with rubber ring joints complete all as specified and directed.

S&F 110mm bore PVC (SWR) junction single, (Single T) equal or unequal complete all as specified and directed.

S&F PVC (SWR) 110mm bend complete all as specified and directed.

S&F PVC (SWR) floor trap 110mm dia plain with PVC grating including jointing with solvent cement complete all as specified and directed.

S&F PVC (SWR) gully trap 125/110mm setting and jointing with solvent cement complete all as specified and directed.

S&F PVC(SWR) vent cowl 110mm dia bore complete all as specified and directed.

M&L for concrete bed to drain pipes of 150mm internal dia pipe in PCC 1:3:6 type C-2 using 40 mm graded stone aggregate including packing under ,and haunching against sides of pipes after they are laid and tested complete all as specified and directed.

M&L for 150mm internal dia reinforced concrete pipes, class NP-2 pipes laid in trenches and jointed complete all as specified and directed.

Cutting into existing manholes for connecting new drains for 150mm bore pipe, good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished, and reforming benching as required complete all as specified and directed.

M&L for brick work using old size bricks with sub class 'B' bricks straight or curved on plan to any radius in half brick thick wall built in cement mortar 1:4 complete all as specified and directed.

S&F hollow MS steel single rebated door frame or any other simillar works of approved shape and size complete all as specified and directed.

S&F 32mm thick flush shutter, factory made, solid core construction with particle board care and plywood face panels commercial type on both side complete all as specified and as directed.

M&L for preparation of new or previously untreated surfaces of wood or wood based materials of any description, not other wise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

S&F vitreous china wash hand basin counter top of size 550mmX400mm fixed on granite slab, CP brass coupling, waste pipe complete all as specified and directed. Note:- Granite stone slab shall be measured and paid separately.

M&L for 20 mm thick granite (of any type) (work table rubbed and polished) laid over beding in 12mm thick CM 1:3 and pointing with white cement 1:2 using marble dust admixture to pigment to match the surface including rounding of edges complete all as specified and directed.

S&F vitreous china urinal half stall size 590x390mm complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement, including 32mm dia CP coupling, CP urinal spreader with CP pipe up tp angle cock, waste pipe etc with all fixing arrangement and pointing around urinal, flush pipe complete all as specified and directed.

M&L for plain cement concrete 1:2:4 type B-0 (12.5mm graded stone aggregate) as in roof padding, roof kerbs, benching on roof slab and other similar works laid as per slope requied finished even and fair complete all as spd and directed

M&L for 10 mm thick plaster in CM 1:3 mixed with liquid water proofing compound over concrete surface of roof when concrete is green complete all as specified and direected.

M&L for cleaning the dust, durt and any other foreign material from roof surface and applying a coat of bituminous primer @ 0.40 tr/Sqm uniformily and primer shall be allowed to dry over night as conforming to IS 3384-1986 complete all as specified and directed.

M&L for laying of 3mm thick APP membrane of (reinforced with non-woven fabric polyester type) (weight not less than 3kg/Sqm) shall be done using butane torch maintaining 100mm ie overlap and 150mm end overlap, sealing all overlaps and bonded to the surface by fusing and bonding torchon complete all as specified and directed. (Note: All water proofing work shall be done as per manufacturer technical representative.)

M&L appying two coats of bitumen based aluminium paint @ 0.15 Kg / Sqm on WPT complete all as specified and directed.

Removing excavated material to a distance exc 250 mtrs and n.exc. 500 mtrs and depositing where directed at a level not exc 1.5 mtr above the starting point complete all as specified and directed.

S&F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.5mm thick (BMT) of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixing with self tapping screws complete all as specified and directed.

S&F rolled mild steel work in tubular trusses including vertical member, rafter and purline including special shaped washer etc using ERW or induction butt welded tubes conforming to IS 1161-1979 graded st-240 including cutting to dead length, notching, drilling riveting and/or welding & connecting with nuts & bolts complete all as specified.

S&F plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment conforming Fe-290 (Gde E-165) complete all as specified and directed.

S&F mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, 11 to 15mm dia of neck exc 15cm and n-exc 22.5cm long complete all as specified and directed.

M&L for 60mm thick, rubber moulded precast concrete interlocking coloured paver block / tiles M-35 grade, factory made, confirming to IS-15658-2006 over and including 30mm thick sand cushioning and joints filled with fine sand incl leveling tamping & sweeping complete all as specified and directed.

M&L for machine cut Pre Polished Kota stone slab 18 to 20mm thick (minimum size 30cmx45cm) as in flooring, laid over and including cement screed bed 20 mm thick in cement mortar 1:4, and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and granite polishing complete all as specified and directed.

Excavation in post holes (or similar holes) each n. exc 0.5cum getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm complete all as specified and directed.

M&L for plain cement concrete 1:3:6 type C-2 using 40mm graded stone aggregate as in post holes, filling and mass concrete complete all as specified and directed.

M&L for framed brackets of angles or tees with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angles, as necessary, gusset plates, riveting, etc.. n exc 10 kg each brackets, conforming to Fe.290.Gde-E-165 complete all as specified and directed.

Roughening surfaces of old concrete floor by sweeping clean and washing down with water to remove dust etc and brushing neat cement slurry with 3.0 Kg of cement per Sqm complete all as specified & directed.

M&L for first or premium quality full body Vitrified Ceramic dark shed coloured tiles 10 mm thick (square/ rectangular, Full body vitrified) polished, area of each tiles n.exc 0.36sqm , in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed in CM 1:6 in floor complete all as specified and directed.

M&L for first or premium quality Vitrified Ceramic coloured tiles 10 mm thick (square/ rectangular) polished, area of each tiles n.exc 0.36sqm , in skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed in CM 1:4 as in skerting complete all as specified and directed.

S&F powder coated anodised aluminium door with shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 02 Nos in each door, hinges, anodised aluminium snap beading, screws etc. including 5mm thick with rubber packing complete all as specified and directed.

S&F powder coated anodised aluminium sliding window with three track bottom track size 92x29.5 x2mm thick, side & top track frame size 92x29.5x2mm thick and shutter aluminium anodised 39x20x2mm thick including necessary aluminium fittings like jointing cleats, glazing cleats, rubber packing, anodised aluminium snap beading, screws etc with 5mm thick tinted / plain glass in panels and stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40 mm including all fittings & fixture complete all as specified and directed.

S&F powder coated anodised aluminium window and ventelator with shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 02 Nos in each door, hinges, anodised aluminium snap beading, screws etc. including 5mm thick with rubber packing complete all as specified and directed.

S&F anodised aluminium powder coated grill of size 75x75x4mm thick for windows, including jointing cleat, anodised aluminium strip beading screw complete all as specified and as directed.

S&F wardrobe / cupboard of 18 mm thick PVC board plain sheet of grade1 quality of both side prelem fixed with screws, solvent cement/adhesive to make cupboard shutter sides top and bottom, shelves inside the cabinet and shutter or drawer complete all as specified and directed. Make: Rajshree or other approved make

S&F wardrobe / cupboard of 18 mm thick PVC board laminated sheet of grade1 quality of both side prelem fixed with screws, solvent cement/adhesive to make cupboard shutter sides top and bottom, shelves inside the cabinet and shutter or drawer complete all as specified and directed. Make: Rajshree or other approved make

S&F continuous (piano) hinges, stainless steel, bright finish or electro galvanized width of flap 30mm when open complete all as specified and directed.

S&F magnet catcher 50mm size with steel body 'H' type fixed to shutter complete all as specified and directed.

S&F 150mm size brass handle, cast type, polished bright complete all as specified and directed.

S&F 25mm dia stainless steel , curtain rails/ drapery rod including end brackets and end knobs etc. complete all as specified and directed.

S&F brass chromium plated peg sets of 06 No knob fixed to shutter complete all as specified and directed.

Provn of post construction anti termite treatment (ATT) with Chloropyriphos 20% EC/Imidcloprid 30.5% SC with following specification complete all as specified & as directed (a) Treatement of Jn of walls and floors : Drilling 10mm dia hole about 30cms apart and deep enough to reach the soil below at the junction of walls and floors squirting termiticide chemical solution through these holes under pressure to charge the soil below thus forming an impregnable chemical barrier imprevious to subterran termites. (b) External perimeter treatment : Drilling 10mm dia holes in the external perimeter to the building i.e along the external wall surface of the building 30cm apart and deep enough to reach the soil, squiriting chemical through these holes under pressure till refusal or a miximum up to 300ml of aqueous solution per hole. (c) Joinery treatment : Drilling 6mm dia holes at the joinery of door/windows and masonry at suitable interval and squirting till resusal both inside and outside of the building. (d) All the termite runways shall be sprayed over and after 15 min, these shall be removed. (e) If there is the infestation occured in the electrical switch board, it shall be treated liberally with chemical dust and fumigants. (f) Wooden treatment : Control measure consist of treatment to wooden installation and fixture by spraying a special oil/water based insecticidal/flying wood damaging insect pests.

M&L for point wiring for one light/fan point controlled by one 5A switch using 1.5 sqmm cable (nominal area) stranded copper conductor (FRLS), single core, PVC insulated and unsheathed cable, 1100 V grade in and including concealed PVC conduit of size not less than 20mm dia all as directed with sunken type pressed steel terminal box 1.6 mm thick of suitable size, duly painted with one coat of red oxide primer and two coats of black bituminous paint for mounting fittings/ junction boxes and wiring to be terminated in pressed steel sunken boxes with and including all accessories with decorative laminated sheet top cover 3 mm thick (Hylam) and using 1.5 Sqmm (nominal area) stranded copper conductor single core conductor PVC insulated and unsheathed cable as in earth wire connected to common earth dolly completed all as specified and directed.

S&F switch piano, flush type 5/6 amp, single pole, one way 240 volt complete all as specified and directed.

S&F ceiling rose surface polycarbonate 65X50mm three terminals complete all as specified and directed.

S&F surface /wall mounted light fitting in CRCA powder coated white housing with pre wired suitable for single T8 LED tube along with supply and fixing one number LED tube in polycarbonate housing of nominal wattage - 18 Watt, Lumen out put - 2100 Lm, Colour Temp - 6500 Kelvin, Size & Length - G13/ T8/ 4 Feet with integral/in built driver, having short circuit and surge protection including making connection with two core PVC insulated, sheathed copper conductor cable of size 23/0.0076 complete all as specified and directed. Make: Cat Part No for batten:- REGALBATTENT8UPTO1X18WDSBSWH of make Havells 'or' IGP161LT8-16 of make Crompton 'or' TMC501 P 1xT-LED 22W P3241 of make Philips Cat Part No for Tubelight:- PHOTANULTRA2.01213T8SSTL18WLED865SPC of make Havells 'or' LTT8-20 of make Crompton 'or' MAS LEDtube 1200MM 18W865 T8 I-2100 lm of make Philips

S&F LED 10 W bulk head fitting luminarire with opal diffuser complete all as specified and directed. Make Crompton Cat No LBH-10-CDLSYSKA equivalent Model of C&S,Havells.

S&F exhaust fan single phase 230/240 volt AC 300mm sweep, 1400 RPM with painted louvers, metal body, including cutting holes of suitable size in wall, grouting of nuts and bolt etc required for fixing fan and making good to match the existing surface and making connection with twisted copper flexible wire 23/0.0076mm complete all as specified and directed. Make: Havells/Bajaj/CG.

S&F factory made epoxy powder coated distribution board SPN 4 ways double door with acrylic top cover (IP-43 protection) fabricated from minimum 1.6mm thick CRCA sheet and fixed flush to wall and suitable for universal mounting and including 200 Amps copper bus bar, neutral bar, standard DIN rail, earth bar and cable ties for cable management, top and bottom removable gland plates all as specified & directed.

S&F MCB, SP, 6 to 32 Amps, 'C' curve, 10 KA breaking capacity, 240 volts complete all as specified and directed.

S&F MCB, SPN, 40 to 63 Amps, 'C' curve, 10 KA breaking capacity, 240 volts complete all as specified and directed.

Excavation in trenches in soft/loose soil n.exc 1.5 mtr wide and n.exc 1.5 mtr depth and getting out complete all as specified and directed.

Returning, filling in including spreading, leveling, watering and well ramming in layers not exc 25 cm thick complete all as specified and directed.

Removing surplus excavated material not exc 50 mtrs and depositing where directed at a level not exc 1.5 mtr above the starting point complete all as specified and directed.

Supply and providing sand cushioning with dry clean sand 15 cm below cable and 8 cm above the cable complete all as specified and directed. Note: Punned thickness shall be measured for the purpose of payments.

Supply and laying burnt bricks old size sub class-B laid in trenches for cable protection with length of brick perpendicular to length of cable complete all as specified and directed.

S&F 40mm bore GI pipe, light grade with all fittings laid in trenches, road crossing and fixed to walls, on poles etc for cable protection complete all as specified and directed.

Supply, laying and testing 16 Sqmm, 2.0 Core XLPE insulated, armoured heavy duty electric cable, screened PVC bedded, galvanised steel strip or wire, with aluminium conductor 1100 V grade, laid in trenches/ along poles, ducts or through sleeve complete all as specified and directed Note: Earth work, sand cushioning and bricks will be measured and paid separately under relevant items.

S&F GI tubing, 20mm bore 'medium grade' galvanised, with all fitting and fixed complete to trench, walls and ceilings or laid in floors complete all as specified and directed.

S&F GI tubing, 25mm bore 'medium grade' galvanised, with all fitting and fixed complete to trench, walls and ceilings or laid in floors complete all as specified and directed.

S&F GI tubing, 50mm bore 'medium grade' galvanised, with all fitting and fixed complete to trench, walls and ceilings or laid in floors complete all as specified and directed.

S&F stop valve 25mm bore, cast copper alloy with long shank and cup screwed down, high pressure, with crutch of butterfly handle, screwed both ends for iron pipes or for unions complete all as specified and directed.