REPAIRS TO JOINERY, FLOORING, ROOFS, PLASTERING AND PLUMBING ETC IN ZONE B AT DAMANA UNDER GE JAMMU

Amount

Taking down chowkats or frames with shutters (w/o taking off shutters from the frames) not exc 1.5 sqm each, including cutting holes for taking out holdfasts or dismantling brick work (holes cut and any other damage to jambs, walls for taking out holdfasts shall be finished identical to existing finish (without any extra cost to Govt) and removing from site all as specified and as directed by Engr-in-Charge.

All as per Ser Item No 1.00 above but exc 1.5 sqm and not exc 4 sqm each all as specified and as directed by Engr-in-Charge.

Taking down shutters of any description exc 1 sqm and n exc 2 sqm each complete all as specified and directed by Engr-in-Charge.

Taking down shutters and refixing in same opening after resecuring or easing and adjusting, also refixing builders hardware as required including renewal of unserviceable screws etc of any description exc 1 sqm and n exc 2 sqm each complete all as specified and directed by Engr-in-Charge.

M&L Factory made pressed steel frames of size 105 X 60 mm made out of PBI sheet 1.25mm thick for doors with one or more rebates including necessary fixing lugs, hinge, lock strike plate etc complete including bottom of each chowkat to be welded with 02 nos 25 X 25 X 3mm angle iron projecting 10cm one either side including one shop coat of red oxide chrome primer and including PCC 1:3:6 type C-0 in back filling of chowkats and tarring back of chowkats and holdfasts all as specified and as directed.

All as per Ser Item No 5.00 above but frame size 125 X 60mm all as specified and as directed.

Supply and fix solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube supplying and fixing in opening as per specification all as specified and as directed.

S&F Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of mild steel tubes for top and bottom rails Mild steel frame shall be covered with heat moulded plain cover PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and gap insert for top rail and bottom rail; Panelling of plain colour PVC sheet to be fitted in the mild steel frame welded/ sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement supplying and fixing in the frame at site as per specification clause No 8B.1 to 8B.10 and drawing on page No. 156 of MES SSR-2010 Part-II all as specified and as directed.

S&F mild steel butt hinges medium weight 75mm long all as specified and as directed by Engr-in-Charge.

S&F Factory made, 2nd class hard wood, plain framed, panelled shutters (two panels) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both sides, the size of rail and stile as per IS-1003 (Part-I), kiln seasoned and chemically pressure treated 35mm thick complete, all as specified and as directed by Engr-in-Charge.

S&F Factory made, 2nd class hard wood, glazed and skelton shutter 35mm thick open rebated and prepared to receive glass, gauge etc (without sash bars), edges of framing palin, chamfered or rounded, fitted with cut and mitred beads for securing glass etc sizes of members of shutters as specified in SSR 2009 Pt-I Section 8.24 (b) supplied and fitted to chowkhats all as specified and as directed.

S&F mild steel butt hinges medium weight 100mm long all as specified and as directed.

S&F steel window 1.25mm thick Box type (Primer coated) ERW hollow P section of size 60X25mm single rebated comprises glazed Skelton shutter ERW sec 50X20mm and 1mm thick with two Nos sash bar of T-section 20mmX3mm complete welded to frame with one vertical mullion of ERW box type T-section of size 60X25mm and 1.25mm thick including cutting holes and making good dismantled portion in PCC 1:2:4 type B-1 four No for each window including following fitting welded to frame shutter hold fast of 150mm long of 12mmX3mm FI made to shape 4 No, handle of Z section 20mmX25mmX1000mm long 1 No per leaf, MS tower bolt 150mm long 2 No per leaf, Z sec 20mmX25mm, 100mm long stopper 1 No on per leaf, MS pintal hinges of size 75mmX12mm 2 No per leaf fabrication and fixing arrangement as per drg No CEPZ/TD-324, 325/07 all as specified and as directed.

S&F steel window 1.25mm thick Box type (Primer coated) ERW hollow P section of size 60X25mm single rebated comprises wire gauged Skelton shutter ERW sec 50X20mm and 1mm thick with two Nos of FI section complete welded to frame for holding wire mesh with one vertical mullion of ERW box type T-section of size 60X25mm and 1.25mm thick including cutting holes and making good dismantled portion in PCC 1:2:4 type B-1 four No for each window including following fitting welded to frame shutter hold fast of 150mm long of 12mmX3mm FI made to shape 4 No, handle of Z section 20mmX25mmX100mm long 1 No per leaf, MS pintal hinges of size 75mmX12mm 2 No per leaf fabrication and fixing arrangement as per drg CEPZ/TD-324, 325/07 all as specified and as directed.

S&F Framed work such as grills, gratings etc with ends of bars shouldered and/or riveted or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railing frame work of water tanks, Cupboard frame etc (including cutting holes in brick masonery walls and fixed with PCC 1:11/ 2:3) and similar work confirming to Fe.290.Gde-E-165 all as specified and as directed.

S&F in repairs 18/19mm thick Prelaminated Particle board, interior grade, prelaminated one side with decorative choice lamination and other side balancing white lamination, fixed with scres/nails to timber/steel frame work as in shelves, cup board shutters, book case, writing table stand, shelves etc including fixing of plain fillets square or rectangular of 2nd class hard wood not exc. 3 sq.cm in leaping to shutters/shelves complete fixed all as specified and as directed.

S&F continuous piano hinges, mild steel, bright finish or electrogalvanised, width of flap 30mm (when open) fixed with welding all as specified and as directed.

S&F Hasp and staple size 100mm, aluminium anodised, safety type, brass with mild steel hinge pin including bolt to hinge plate and fixed with screws all as specified and as directed.

S&F Aluminium handle cast type, anodised size 125mm long, D type complete all as specified and as directed.

S&F Mild steel barrel tower bolts, stove enamelled black, with bright bolt and fixed 200mm all as specified and as directed.

S&F 250mm Mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and as directed.

S&F Galvanised mild steel wire cloth, 0.46mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples all as specified and as directed.

S&F in repairs Galvanised mild steel wire cloth, 0.46mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples all as speciifed and as directed.

S&F in repairs Helical door spring 150mm including roller and roller plate complete fixed with welding to existing steel chowkhats all as specified and as directed.

Hacking out old broken glass of any thickness, size, quality or description from the wooden frames glazing with putty or fixed with wooden beads complete all as specified and directed.

S&F 3mm thick ordinary glass sheet quality and glazing with oil putty in square n.exc. 0.5 sqm in each pane including punching or drilling out old glazing pins or spring clips and providing and fixing new clips or pins, including scaffolding to reach up to 4 storey building all as specified and as directed.

All as per Ser Item No 26.00 above but frosted glass all as specified and as directed.

S&F in repairs Curtain/drapery rod 20mm dia MS fancy PVC coating type complete with clamps, ring and ball shaped at both end, all golden colour/Cherry colour, complete all as specified and as directed by Engr-in-Charge.

M&L applying two coats of synthetic enamel paint on wooden surface over one coat of pink primer including preparation of new surface over 10cm width or girth all as specified and as directed.

M&L for two coat synthetic enamel paint on old steel surfaces of any description not otherwise described over 10 cm width or girth including preparation of surface all as specified and directed.

S & F 100 mm size butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21 complete all as specified and directed.

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps cills, sunshades, shelves,lintels etc; and cutting chases for concealed water tubing and making good, cutting not exc. 10cm girth all as specified and directed.

Taking upto down steel tubing with connections for cleaning for refixing or removing or storeyard complete of bore 15mm all as specified and directed.

Taking upto down steel tubing with connections for cleaning for refixing or removing or storeyard complete of bore 20mm all as specified and as directed.

S&F Steel water tubing medium grade galvanised with all fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete with all fittings (such as bends, elbows, Tee short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.) of nominal bore 15mm, all as specified and as directed.

S&F Steel water tubing medium grade galvanised with all fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete with all fittings (such as bends, elbows, Tee short pieces, connectors, back nuts, diminishing pieces, caps and plugs,unions etc.) of nominal bore 20mm, all as specified and as directed.

Refixing only 15mm dia steel tubing and connections in new or old position including cleaning of old steel tubing complete all as specified and directed.

Refixing only 20mm dia steel tubing and connections in new or old position including cleaning of old steel tubing complete all as specified and directed.

S&F in repair PVC low level flushing cistern valve less, syphonic action type of 10 ltrs capacity white with inlet, ball valve, float and handle including cast iron brackets, PVC flush pipe 32mm dia, PVC connection (15x 450 mm) long, fancy type chromium plated angle valve of 15mm bore dia complete all as specified and directed.

S&F in repair Vitreous china squatting pan 'Orissa' pattern ' size 580x440mm white, with integral foot rest 'P' or 'S' trap, front or back inlet including connection to trap and to flushing pipe,anti syphonage pipe, etc. Complete making good to floor as existing complete all as specified and directed by Engr-in-Charge.

S&F in repairs Vitreous china wash down water closet pan (pedestal pattern), white including fixing bolts,flush pipe and joints complete all as specified and directed by Engr-in-Charge.

S&F in repairs stainless steel sink with drainage board,made of 1.00mm thick sheet for kitchen or laboratory with plug,washers, waste pipe including bedding in cement mortar to dwarf wall or including fixing cast iron cantilever brackets,connecting union to pipe, overall size 915mmx460mm, bowl size (410x330x160mm) as in repair all as specified and directed.

S&F in repairs kitchen plate rack of stainless steel of size 900 x 800 x 230mm made out of 1mm thick stainless steel sheet all as specified and directed.

S&F in repairs Vitreous china wash hand basin white ,flat back of size 550x400mm with PVC connection (15x450)mm long with PTMT nuts and PVC washer and including cutting for pinning in ends,pair of cast iron brackets and provision of PVC waste pipe 32mm of adequate length , CP waste coupling 32 mm dia of half or full threaded, chromium plated fancy type angle valve 15 mm dia bore, and taking down unserviceable wash hand basin complete all as specified and directed by Engr-in-charge.

S&F in repairs Pillar tap fancy type chromium plated with capstan head, screwed down high pressure with long screwed shanks and fly nuts, screwed for iron pipes 15 mm bore dia all as specified and directed.

S&F in repairs brass CP Mixer of bore dia of pipe 15mm for mixing hot & cold water screwed down for iron pipe and fixed all as specified and directed.

Dismantling PVC water tank/demolition of RCC water storage tanks of capacity upto 1000 ltrs and removing from site all as specified and directed.

S&F Rotational moulded polyethylene water storage tank including, plastic lid cover, double layered, cylindrical vertical with closed top hoisted and fixed in position of capacity 500ltrs including making connections, 20 mm dia ball valves high pressure PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe anf fixed (minimum weight 210 gram) complete all as specified and as directed in SSR Part I.

S&F Rotational moulded polyethylene water storage tank including, plastic lid cover, double layered, cylindrical vertical with closed top hoisted and fixed in position of capacity 1000 ltrs including making connections,20 mm dia ball valves high pressure PTMT with epoxy coated aluminium rod and high density plastic ballscrewed for iron pipe anf fixed (minimum weight 210 gram) complete all as specified and as directed in SSR Part I.

S&F in repairs 20 mm dia Ball valves high pressure PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe anf fixed (minimum weight 210 gram), screwed for iron pipe or brass ferrule and fixed complete all as specified.

Taking down cement plaster of any description on brick or stone walls or from concrete surface incl raking out joints, hacking for key,scrubbing down with water and removing unserviceable material outside cantt area all as specified and directed by Engr-in-Charge. Note: Plaster work may be in patches upto triple storey.

M&L Rendering 15mm thick in CM 1:6 on fair faces of brick surface finished even and smooth without using extra cement upto height of four storey building all as specified and as directed.

M&L Rendering 10mm thick in CM 1:3 on fair faces of concrete surface of ceiling, finished even and smooth without using extra cement, all as specified and as directed by Engineer-in-Charge.

M&L Rendering 15mm thick in CM 1:4 on fair faces of brick surface finished even and smooth without using extra cement etc. all as specified and as directed. (including all necessary scaffolding lifiting arrangement for external surfaces).

M&L Preparing plastered or unplastered new surfaces of walls and applying two coats of dry distemper complete all as specified and as directed.

M&L applying two coats of cement based paint including preparation of new plastered surface complete all as specified and as directed.

M&L applying three coats of white wash on ceiling incl preparation of newly plastered surface complete all as specified and as directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings n. exc 15cm thickness (below or above ground level) and removing unserviceable material outside cantt area all as specified and directed by Engr-in-Charge.

M&L cement concrete 50mm thick in 1:3:6 type C-2 (40 mm graded aggregate) as in flooring finished even & rough all as specified and directed.

M&L Factory made precast hand crafted chequered cement concrete M-40 grade coloured tiles 30cm x 30cm x 22 mm thick, polymer moulded set, jointed and pointed in neat cement slurry in floors with white cement and pigment over and including screed bed and bedding layer of mortar 20mm thick in cement plaster (1:4) for laying floor finishes, as per design/pattern approved by Engr-in-Charge.

Dismantling floors hearth or wall tilling including cement mortor bedding (but not backing) removing unserviceable materials outside MOD area and rubbish off the premises all as specified and directed.

M&L Non skid ceramic coloured tiles 7 to 8mm thick area of each tile exceeding 0.11 sqm but not exc 0.18 sqm,in floors etc.set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface over and including 15mm thick screed bed in CM 1:4 all as specified and directed.

All as per Ser item No 63.00 above but as in skirting including 10 mm thick rendering in cement mortar 1:4, complete all as specified and directed.

M&L Vitrified tiles light shade 10mm thick (square/rectangular) polished,area of each tiles not exceeding 0.36 sqm, as in floors etc.set and jointed in neat cement slurry and pointed in white or coloured cement to match shade over and including screed bed 15mm thick in CM 1:4 complete all as specified and directed.

M&L Vitrified tiles light shade 10mm thick (square/rectangular) polished,area of each tiles not exceeding 0.36 sqm,as on vertical surfaces etc.set and jointed in neat cement slurry and pointed in white or coloured cement to match shade over and including 15mm thick screed in CM 1:4 complete all as specified and directed.

M&L Glazed ceramic coloured tiles 300x450x7 to 8 mm thick on vertical surface as in skirting,dado set and jointed with neat cement slurry and pointed in white or coloured cement to match with the surface over and including taking down old plaster and 10 mm thick screed in CM 1:4 complete all as specified and directed.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc all as specified and directed.

M&L Granite 15 to 20mm thick (Pure black)(tabled rubbed and polished) as in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar 1:4 including pointing in colour cement 1;2 using marble dust with admixture of pigment to match with shade of granite over and including 15mm thick screedbed in cm1:4 edges of slab to be rounded from all sides (including cutting, wastage and polishing) complete all as specified and as directed.

Removing existing treatment from roof surfaces such as tiling, tarfelt, fungus,moss,dust etc.,cleaning the surface of all foreign material by wire brushing and dusting and racking out RCC slab complete all as specified and directed and removing the debris outside defence land.

M&L for Rendering 20 mm thick in CM 1:4 on fair faces of brick work surfaces finished even and smooth without using extra cement up including mixing liquid water proofing compound complete all as specified and as directed. Note- liquid water proofing compound shall be measured and paid separately.

Cleaning the roof surfaces and applying bitumen primer @ 0.30 kg/sqm, providing and laying 3mm thick APP modified water proofing membrane weighing not less than 3.00 kg/sqm reinforced with non woven polyester mat weighing not less than 160 gm/sqm, having softening point not less than 800 N /Sq cm, tearing strength of 180N, with minimum of 10 cm side laps and 15cm end laps, laying by application of torch, and applying industrial bitumen 85/25 @ 1.2 kg/sqm on top surface complete all as specified and directed.

Supply only liquid water proofing compound all as specified and directed.

S&F in repairs chromium plated bib tap 15mm size with crutch or butterfly handle screwed down screwed fro iron pipe or for brass ferrule and fixed all as specified and directed.

S&F Plain aluminium sheeting 0.71mm thick , in crumple joint covering, ridges, hips, valley gutters, drip and strainght flashings (length and girth as fixed) with grade of zinc coating 275 all as specified and directed.

S&F angle/stop valve of cast copper alloy screwed down high pressure with crutch or butterfly handle screwed bother ends for iron pipe or for uniorns and fixed 15 mm bore all as specified and directed.

S&F swivel shower rose PTMT any colour with arm 15mm size 195mm long all as specified and directed.

Dismanting asbestos cement (corrugated or semicorrugated etc) sheets in roof covering all as specified and directed.

M&L for 6mm thick asbestos cement, corrugated or semi-corrugated sheets fixed with L-type or J-type or cranked hook boltsin roofs, walls etc all as specified and directed.

Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified and as directed.

Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified and as directed.

Dismantling timber scantling 40 sq cm and over in section framed work of any description all as specified and directed.

Dismantling structural steel work including doors, gates of any description all as specified and directed.

S&F for structural steel works of Fe 410W (Gde E 250) quality A, as in Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. including painted one shop coat of zinc chromate/red oxide primer paint (including preparation of surface) before fabrication all as specified and directed.

M&L for clean sawn timber in fixed second class soft wood in scantlings all as specified and directed.

Dismantling boarding any description fixed in any position with nail complete all as specified and directed.

S&F for frame work for ceiling with specification as under mentioned:- (i) GI section frame work (Powder coated) for white, pre-premiered, self embossed, reinforced designer board consisting of perimeter wall angle 19mmX19mmX0.45mm, cross 'Tee' 28.6mm (web)X 24mm flange 0.33mm thick powdered coated main tee 38mm (Web) X24mm flange 0.33mm thick. wall angle shall be screwed/ fixed to brick wall / partition wall / concrete / RCC with the help of nylon sleeves and screws @ 610 mm C/C , then suspending GI main 'Tee' in both directions by means of hangers with alignment @ 1220mm C/C to soffits. To from grid of 610X610mm cross Tee shall be provided @ 610mm C/C in both directions and all suitable provisions shall be made for fixing the recessed/surface mounting light fittings if any, complete all as specified and directed by Engr-in-Charge.

S&F for 4 mm thick non asbestos fibre cement building boards 60 x 60 cm in size including two coat of white wash after preparation of surface, fixed/laid/ inserted to GI framework at ceiling with screws complete all as specified and directed.

M&L for two coat synthetic enamel paint over a coat of red oxide primer on steel surfaces of any description not otherwise described over 10 cm width or girth including preparation of surface all as specified and directed.

S&F PVC connection 15mm, 450mm long with nuts and washers complete all as specified and directed.

M&L for 75 mm thick PCC 1:3:6, type C2, using 40 mm graded stone aggregate as in plinth protection etc., finished even and smooth without using extra cement all as specified and directed.

M&L for double action floor spring hydraulically regulated made of minimum 1.25mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed in repairs all as defined and all as specified and directed.

Repair to Aluminium door including adjusting, necessary bedding, clip, rubber beader, repair to floor door closer all as specified and directed.

S&F Aluminium (extruded section) body door closer hydraullicaly regulated designation No 2, universal type suitable for door shutters of 701 to 850mm in width and of weight between 36 and 60kg and fixed in repairs all as specified and directed.

S&F in repairs waste coupling of PTMT (half or full threaded) of bore dia 32 mm discharge pipe all as specified and directed.

S&F in repairs waste coupling of PTMT (half or full threaded) of bore dia 40 mm discharge pipe all as specified and directed.

S&F brass Phase for CP bib tap, pillar tap, angle valve for suitable 15mm dia full turn, half turn as per sample all as specified and directed.

S&F brass Phase for CP concealed stop cock for suitable 15mm dia full turn, half turn as per sample all as specified and directed.

S&F Grating doom 100mm dia without hole chromium plated all as specified and directed.

S&F Grating doom 100mm dia with hole, chromium plated all as specified and directed.

S&F in repairs PTMT Syphonic assembly for low level flushing cisterns of 10 ltr capacity complete all as per sample kept in the office of AGE B/R Damana all as specified and directed.

S&F 15mm bore long body Bib tap cast copper alloy fancy type chromium plated with capstan handle screwed down screwed for iron pipe or for brass ferrule. as per sample kept in AGE B/R Damana office all as specified and directed.

S&F PVC Waste pipe 32 mm dia and suitable length straight or flexible type for wash hand basin / sink all as specified and directed.

S&F PVC Waste pipe 40 mm dia and suitable length straight or flexible type for wash hand basin / sink all as specified and directed.

S&F Floor door stopper of aluminium alloy body and tongue, anodized with hard drawn steel spring, overall length of cover plate as 140mm all as specified and directed.

S&F PVC tank cover for water stoarage tank for 500 ltr capacity including locking arrangement all as specified and directed.

S & F in repair 110 mm dia bore PVC (SWR) pipes single socketed in any length with solvent cement joints, fixed to wall all as specified and directed.

S & F in repair 75 mm dia bore PVC (SWR) pipes single socketed in any length with solvent cement joints, fixed to wall all as specified and directed.

S&F in repairs PVC SWR bends of bore 110mm dia complete all as specified and directed.

S&F in repairs PVC SWR bends of bore 75 mm dia complete all as specified and directed.

M/s Koul & Sons

Jagbir Singh and Co

M/S OM GUPTA

Bidder Name

Vijay Kumar and Co

Jagbir Singh and Co

M/S OM GUPTA

M/s Koul & Sons