PROVISION OF STORAGE SPACE AT CGRSD, RENOVATION OF CG MI ROOM AND CERTAIN WORKS AT VISHWAKARMA COMPLEX AT NSRY UNDER GE HADDO

Amount

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for complete all as specified and as directed.

Demolition of cement concrete (un reinforced) in ground floors and pavings not exceeding 15 cm thickness (below or above ground level) complete all as specified and as directed.

Demolition of cement concrete (reinforced) of any description and in any position not otherwise specifically provided for (reinforcement cut as required to facilitate demolition) complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed.

Dismantling stone slabs and tiles of any description or thickness in floors, aprons, risers of steps, skirting, dado etc., laid bedded and pointed in any mortar mortarcomplete all as specified and as directed.

Dismantling ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets complete all as specified and as directed.

Dismantling PVC (SWR)/ cast iron pipes of 110mm dia in any position alongwith all fittings and fixtures by removing at joints complete all as specified and as directed.

Dismantling PVC (SWR)/ cast iron pipes of 75mm dia in any position alongwith all fittings and fixtures by removing at joints complete all as specified and as directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames), area not exceeding 1.5 Sqm each complete all as specified and as directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames), area exceeding 1.5 Sqm but not exceeding 4.0 Sqm each complete all as specified and as directed.

Taking down shutters of any description, area exceeding 1.0 Sqm but not exceeding 2.0 Sqm each and re-fixing in the same opening complete all as specified and as directed.

Excavation in trenches not exceeding 1.5 mtr wide and not exceeding 1.5 m in depth, for foundation of poles, stays, struts or for laying cables/pipes etc., not exceeding 10 Sqm on plan and not exceeding 1.5m in depth and getting out in soft/loose soil complete all as specified and as directed. NOTE: 1. If new cable is laid as replacement of old cable in the same trench, all excavation and earth work shall be measured only once. 2. If any pipe is laid in trenches as cable protection, all excavation and earth work shall be measured either for cable or for pipe only and not for both. 3. If cable is laid in tiers and in loops, all excavation and earth work shall be measured accordingly.

Excavating in post holes (or similar holes) in hard/dense soil each not exceeding 0.5 Cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm and removing surplus soil to a distance not exceeding 50 metres and making good disturbed surfaces complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm each as in soils complete all as specified and as directed.

Removing excavated material (soils) to a distance not exceeding 50 metres and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and as directed.

M&L for pre-cast cement concrete block masonry with solid blocks made up of (1:3:6) type C1 (using 20mm graded stone aggregate), masonry exceeding 10cm in width and setting in cement mortar (1:6) complete all as specified and directed.

M&L for pre-cast cement concrete block masonry with solid blocks made up of (1:3:6) type C1 (using 20mm graded stone aggregate), masonry not exceeding 10cm in width and setting in cement mortar (1:4) complete all as specified and directed.

M&L for PCC (1:3:6) type C2 (using 40mm graded stone aggregate) as in foundation filling and mass concrete complete all as specified and as directed.

M&L for PCC (1:4:8) type D2 (using 40mm graded stone aggregate) as in foundation filling and mass concrete complete all as specified and as directed.

M&L for cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring etc., and making good to match with existing surfaces, cutting not exc 10 cm girth in PCC block masonry/RCC complete all as specified and directed.

M&L for reinforced cement concrete (1:2:4) type B1 (using 20mm graded stone aggregate) as in beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and as directed.

M&L for reinforced cement concrete (1:2:4) type B1 (using 20mm graded stone aggregate) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs, cooking platforms and in shelves and the like complete all as specified and as directed.

M&L for use and waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc., for rough finished surfaces of concrete flat complete all as specified and as directed.

S&F Second class hard wood, plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints including preservative treatment complete all as specified and as directed.

S&F flush shutters 30mm thick, solid core construction, with block board core and plywood face panels, commercial type on both sides including 6mm thick wooden lipping around the edges of shutter complete all as specified and as directed.

S&F 35mm thick second class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc., sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a), fixed to chowkats complete all as specified and as directed.

M&L for second class hard wood (Hollock) plain fillets, square, rectangular or triangular in section, clean sawn, secured with nails or brads of sectional area exceeding 13.0 Sqcm not exceeding 25.0 Sqcm complete all as specified and as directed.

S&F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. square tube as per specification & drawing, fixed in opening complete all as specified and as directed.

S&F factory made solid PVC moulded door shutter with particle board core, 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick moulded prelaminated PVC sheet on the front face & 2mm plain colour PVC sheet on back face as per specification & drawing fixed to door frame complete all as specified and as directed.

S&F 100mm size butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised, type B-21 complete all as specified and as directed.

S&F 100mm long aluminium anodised, barrel tower bolts of extruded section complete all as specified and as directed.

S&F 150mm long aluminium anodised, barrel tower bolts of extruded section complete all as specified and as directed.

S&F 100mm size extruded aluminium alloy handles, fabricated type, anodised complete all as specified and as directed.

S&F 150mm size extruded aluminium alloy handles, fabricated type, anodised complete all as specified and as directed.

S&F sliding door bolt, 300mm long, aluminium alloy, anodised, with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy complete all as specified and as directed.

S & F Continuous (piano) hinges, mild steel, bright finish or electrogalvanised, width of flaps 40mm (when open) complete all as specified and as directed.

S&F 75mm size hasp and staple, safety type, aluminium anodised with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and as directed.

S&F door closer, aluminium (extruded section body), hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed with screws complete all as specified and as directed.

S&F Harrison rails (curtain rails), anodised aluminium alloy with fixing brackets, stops, rollers etc., complete all as specified and as directed.

M&L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

M&L for Mild steel TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

M&L for mild steel joist, channel, angle or tee sections, fixed independently, without connecting plates, etc., (cut to ordinary lengths i.e. within 20mm of the length indicated) conforming to Fe-410-W (Gde-E-250) Quality 'A' complete all as specified and as directed.

M&L for mild steel plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment conforming to Fe-410-W (Gde-E-250) Quality 'A' complete all as specified and as directed.

M&L for mild steel framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars and similar work conforming to Fe-290 Gde E-165 complete all as specified and as directed.

M&L for mild steel roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (beam, tee, angle, channel or flat sections) including distance pieces, cleats etc., conforming to Fe-410-W (Gde E-250) Quality 'A' complete all as specified and as directed.

M&L for mild steel rolling shutters with thickness of laths 1.25mm, push pull or manual type without ball bearing, including top cover, anchoring rod, hasp and staple and one shop coat of primer, erected in position as indicated, complete all as specified and as directed.

S&F Ball bearing for rolling shutters complete all as specified and as directed. MAKE: SKF/ TATA/ NBC

S&F Safety lever locks mild steel with 4 levers for rolling shutters complete all as specified and as directed. MAKE: SHEEL/ HARRISON/ LINK

M&L for mild steel hold fasts, bands, straps, supports or stays for rainwater, brackets/clamps for eaves/barge boards and valley gutter and similar articles conforming to Fe-290 Gde-E-165 complete all as specified and as directed.

S&F pre-painted zinc coated aluminum sheet (Galvalume) GI based trapezoidal profile steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed. NOTES: The self tapping screw shall be of adequate length to drive into complete thickness of purlin/rafter etc., and shall be fixed using neoprene and EPDM washers. Penetration and laps in sheet shall be sealed by using proper sealant profile. HDPE fillers shall be provided wherever required to close voids between sheets, sheet & fasteners etc., as per SSR Part-I 2009 complete.

S&F pre-painted zinc coated aluminum sheet (Galvalume) GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall/valley gutters, fixed with self tapping screws including scoffolding for a height upto 12.0 metres complete all as specified and as directed. NOTES: The self tapping screw shall be of adequate length to drive into complete thickness of purlin/rafter etc., and shall be fixed using neoprene and EPDM washers. Penetration and laps in sheet shall be sealed by using proper sealant profile. HDPE fillers shall be provided wherever required to close voids between sheets, sheet & fasteners etc., as per SSR Part-I 2009 complete.

S&F aluminum flat iron wind ties of any size and thickness fixed with self tapping screws for fixing roofing sheets complete all as specified and as directed. NOTES: The self tapping screw shall be of adequate length to drive into complete thickness of purlin/rafter etc., and shall be fixed using neoprene and EPDM washers.

M&L for seamless gypsum board false ceiling 12 mm thick including for any sunk or raised moulding with 25mm long self drilling/tapping screws having Philips head with joining compound and 48 mm wide fibre tape to provide seam less finish and including GI frame work of seamless ceiling comprising of GI perimeter channel 0.55 mm thick with two unequal flange of 20mm and 30 mm, web of 27 mm, fixed to surrounding wall using nylon sleeves and screws at 450 mm c/c / intermediate channel 0.9 mm thick having two equal flanges of 15 mm suspended from soffit at approx 900 mm c/c with GI cleats and steel expansion fasteners with and including ceiling section (not exceeding 1.2 m length) of 0.55 mm thick having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting across the intermediate channel at 457 mm c/c including hangers 6 mm dia GI adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40x3 mm size, 60 mm long & expansion hold fasteners 12.5 mm dia, 40 mm long and finally applying two coats of oil bound distemper with roller finish over a coat of primer complete all as specified and as directed.

M&L for 100mm thick PCC (1:4:8) type D2 (using 40mm graded stone aggregate) as in sub base of floors complete all as specified and as directed.

M&L for vitrified ceramic coloured tiles (ultra charged) 10 mm thick (square/ rectangular) of approved shade, area of each tile exceeding 0.42 Sqm but not exceeding 1.0 Sqm as in floors etc., laid over and including 15mm thick screed bed in CM (1:6), set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed.

M&L for vitrified ceramic coloured tiles (ultra charged) 10 mm thick (square/ rectangular) of approved shade, area of each tile exceeding 0.42 Sqm but not exceeding 1.0 Sqm, for work on vertical surfaces such as skirting, dados and risers to steps etc., including 10mm thick backing coat in CM (1:4), set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed.

M&L for vitrified ceramic coloured tiles 10 mm thick (square/ rectangular) of approved shade, area of each tile not exceeding 0.36 Sqm as in floors etc., laid over and including 15mm thick screed bed in CM (1:6), set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed.

M&L for vitrified ceramic coloured tiles 10 mm thick (square/ rectangular) of approved shade, area of each tile not exceeding 0.36 Sqm, for work on vertical surfaces such as skirting, dados and risers to steps etc., including 10mm thick backing coat in CM (1:4), set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed.

M&L for non-skid ceramic coloured tiles 7 to 8 mm thick (square/ rectangular), area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, as in floors etc, laid over and including 15mm thick screed bed in CM (1:6), set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed.

M&L for glazed ceramic designed coloured tiles in vertical surfaces using size of tiles 450x350x7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match with colour of tile with and including 10mm thick backing coat in CM (1:4), set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed.

M&L for machine cut polished cudappah stone slab 20-25mm thick as in verticals and horizontals supports for shelves and the like including necessary jointing and pointing with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing and making good disturbed surfaces to match with surroundings complete all as specified and as directed.

M&L for 20mm thick granite work (of any type and shade as approved) table rubbed and polished as in steps, jambs, pillars, window cills, cooking platforms, wash basin counters and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite laid over and including 15mm thick cement mortar (1:4) bedding and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing, rounding (chamfering) the edges complete all as specified and directed.

M&L for 20mm thick granite work (of any type and shade as approved) table rubbed and polished as in wall cladding, skirting and the like etc., and pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including 10mm thick backing coat in CM (1:3) complete all as specified and directed.

M&L for glossy finished chequered cement concrete tiles 30cm x 30cm x 25mm thick, made of grey cement and pigments, machine pressed as in flooring, set, jointed and pointed in neat cement slurry laid over and including 15mm thick screed bed in CM (1:4) complete all as specified and as directed.

Taking down cement plaster of any description on brick or stone walls etc., including raking out joints, hacking for key, scrubbing down with water etc., and removing the debris outside MD land complete all as specified and as directed.

M&L for rendering 10mm thick in CM (1:6) on fair faces of brick work or concrete, surfaces finished even and smooth without using extra cement complete all as specified and as directed.

M&L for rendering 15mm thick in two coats 5mm thick in CM (1:4) mixed with integral water proofing compound @ 3% by weight of cement over 10mm thick in CM (1:6) on fair faces of brick work or concrete, surfaces finished fair and even complete all as specified and as directed. NOTE: Water proofing compound will be measured and paid separately under relevant item of this schedule.

M&L for rendering 5mm thick in CM (1:3) on fair faces of concrete as in ceilings, surfaces finished even and smooth without using extra cement complete all as specified and as directed.

Supply only integral water proofing compound.

Supply only liquid water proofing compound.

M&L for preparation of new steel and iron surfaces of any description, not otherwise described, over 10cm in width or girth and applying two coats of synthetic enamel paint of first quality over a coat of red oxide zinc chrome primer complete all as specified and as directed.

M&L for preparation of old steel and iron surfaces of any description, not otherwise described, over 10cm in width or girth and applying two coats of synthetic enamel paint of first quality over a coat of red oxide zinc chrome primer complete all as specified and as directed.

M&L for preparation of old wooden surfaces of any description, not otherwise described, over 10cm in width or girth and applying one coat of synthetic enamel paint of first quality complete all as specified and as directed.

M&L for preparation of new wooden surfaces of any description, not otherwise described, over 10cm in width or girth and applying two coats of synthetic enamel paint of first quality over a coat of pink primer complete all as specified and as directed.

M&L for preparation of old wood/ wood based surfaces of any description, not otherwise described, over 10cm in width or girth for melamine polishing by making surfaces smooth using emery paper, applying filler duly mixed with NC thinner, applying chalk putty in shabby/nailed areas, sand papering the surfaces, and applying exterior sealer (PU), again sand papering and two coats of melamine polish using spray gun to obtain glossy finish complete all as specified and as directed.

M&L for preparation of newly plastered surfaces of external walls of any description and applying two coats of weather proof antifungal (exterior grade) acrylic emulsion over a coat of primer from the same manufacturer complete all as specified and as directed.

M&L for preparation of newly plastered surfaces of walls of any description and applying 3mm thick wall care putty in two coats (primary coat and finishing coat) for smooth surface by grinding/sanding etc., over which applying two coats of distemper oil emulsion over a coat of primer complete all as specified and as directed.

M&L for preparation of newly plastered surfaces of walls of any description and applying two coats of distemper oil emulsion over a coat of primer after levelling the undulations if any with cement putty complete all as specified and as directed.

M&L for preparation of old plastered surfaces of walls by complete removal of existing treatment by scraping, washing, cleaning etc., and applying 3mm thick wall care putty in two coats (primary coat and finishing coat) for smooth surface by grinding/sanding etc., over which applying two coats of distemper oil emulsion over a coat of primer complete all as specified and as directed.

M&L for preparation of newly plastered surfaces of ceilings of any description and applying two coats of distemper oil emulsion over a coat of alkali resistant primer complete all as specified and as directed.

M&L for preparation of old plastered surfaces of ceilings and applying one coat of white wash after filling the cracks, holes with filler complete all as specified and as directed.

M&L for anodised aluminium partition, window and door/ventilator with frame and shutters and grill fully or partly glazed, sliding/openable/fixed fully glazed and panels fixed with panels inserts 12 mm thick pre-laminated particle board/sheet glass including necessary jointing cleats, glazing clips, rubber beading, neoprene packing, anodised aluminium snap beading, screws, anodized aluminium fittings such as handles, aluminium butt hinges, aluminium tower bolts etc. The size of aluminium section shall be all as specified in relevant IS Code and SSR Part-I complete all as specified and as directed. NOTES: (i) Supply only floor spring, glass, Imax hinges, SS friction hinges, particle board, aluminium fly proof mesh will be measured and paid separately under relevant items of this BOQ. (ii) Weight of aluminium section only shall be accounted for the purpose of payment. However unit rate quoted shall be deemed to include for cost of rubber beading, neoprene packing, fittings such as handles, butt hinges, tower bolts, rollers for sliding windows, locking arrangement and fixing only of panel inserts of glass/ particle board/aluminium fly proof mesh etc. (iii) Weight of aluminium handle, butt hinges, tower bolts shall not be accounted for payment purpose.

S&F 18/19mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination and other side with balancing white lamination fixed with screws to timber/aluminium frame work complete all as specified and as directed.

Supply only 4.0 mm thick sheet glass, ordinary quality and glazing with aluminium glazing clips in square not exceeding 0.5 Sqm in each pane complete all as specified and as directed.

Supply only 4.0 mm thick figured glass, pin head type and glazing with aluminium glazing clips in square not exceeding 0.5 Sqm in each pane complete all as specified and as directed.

Supply only aluminium expanded metal fly proof mesh, cut to required size and shape, with 0.45mm nominal dia of wire and average width of aperture 1.40mm complete all as specified and as directed.

S&F aluminium expanded metal fly proof mesh, cut to required size and shape, with 0.45mm nominal dia of wire and average width of aperture 1.40mm complete all as specified and as directed.

S&F Solar control film 25 micron reflective type sticked to glass panes as per instructions of manufacturers complete all as specified and as directed.

S&F aluminium grill of approved pattern, anodised powder coated, cut to required size and shape, fixed in postion with aluminium beading & frame made of aluminium F-section fixed to aluminium windows/ventilators complete all as specified and as directed.

Taking up or down 15mm dia steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and as directed.

S&F 15mm bore unplasticised PVC pipes of pressure rating 10 Kgf/cm² including fittings, fixed complete to walls, ceilings or in floors etc., (including concealing, if required) and to any type of pipe complete all as specified and as directed.

M&L for vitreous China, wash down water closet pan (pedestal pattern), white, including fixing bolts, plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminium hinging device, PVC valveless, syphonic action type, flushing cistern 10 litre capacity, low level, white, with inlet, ball valve, float and handle including brackets, flush pipe of polyethylene of low or high density or PVC 32 mm dia, fixed in repairs complete all as specified and as directed.

M&L for vitreous China wash hand basin, white, flat back, size 550mm x 400mm including cutting for and pinning in ends of brackets or erecting stand, 32mm dia waste coupling brass chromium plated, PVC waste pipe of suitable length, chain and plug, screwed down for iron pipe or for unions complete all as specified and as directed.

M&L for PVC connections 15mm size with PTMT nuts of length 600mm, fixed in repairs complete all as specified and as directed.

S&F toilet paper holder, brass, chromium plated, fixed in repairs complete all as specified and as directed. MAKE: JAQUAR Cat part No. ACN-1153N)

S&F kitchen sink with drainage board made of stainless steel 1mm thick with plugs, washers and wastes, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm, fixed in repairs complete all as specified and as directed.

Drilling holes with electric drill machine for gas pipe etc., not exceeding 25mm dia, upto 10 cm in depth in granite/marble stone complete all as specified and as directed.

S&F 25mm dia gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron or CPVC pipe, fixed in repairs complete all as specified and as directed.

S&F 20mm dia gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron or CPVC pipe, fixed in repairs complete all as specified and as directed.

S&F bib tap, 15mm dia, cast copper alloy, chromium plated, fancy type, with crutch or butterfly handle, screwed down, screwed for iron pipe or brass ferrule, fixed in repairs complete all as specified and as directed.

S&F pillar tap, brass, 15mm dia, chromium plated, fancy type with capstan heads, screwed down, high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe, fixed in repairs complete all as specified and as directed.

S&F angular stop cock, 15mm dia, cast copper alloy, chromium plated, fancy type, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions, fixed in repairs complete all as specified and as directed.

S&F angular stop cock, 15mm dia, cast copper alloy, chromium plated, fancy type, screwed down, high pressure, with crutch or butterfly handle, with long shank and cup (concealed type) screwed both ends for iron pipe or for unions, fixed in repairs complete all as specified and as directed.

S&F two way bib tap, brass, 15mm dia, chromium plated, fancy type, with crutch or butterfly handle, with long shank and cup, screwed down, screwed for iron pipe or brass ferrule, fixed in repairs complete all as specified and as directed. MAKE: JAQUAR Cat part No. CAN-FLR-5041N)

S&F hand shower (health faucet) with 8mm dia and 1.0 m long flexible tube with wall hook, fixed in repairs complete all as specified and as directed. MAKE: JAQUAR Cat part No. ALD-573

S&F grating 100mm dia, chrome plated complete all as specified and as directed.

S&F soap dish, brass, chromium plated, fixed to wall with rawl plug and brass screws, fixed in repairs complete all as specified and as directed.

S&F towel ring (square), brass, chromium plated with round flange, fixed in repairs complete all as specified and as directed. MAKE: JAQUAR Cat part No. ACN-1121N)

S&F over head shower rose, with or without swivel joints, brass, chromium plated, 15mm dia or bore, fixed in repairs complete all as specified and as directed.

S&F 110mm bore PVC (SWR) pipes single socketed, in any length pipes single socketed, in any length with rubber ring joints, laid in trenches/fixed to walls with necessary clamps/placed in weep holes using synthetic rubber adhesive cement solvent complete all as specified and as directed.

S&F 75mm bore PVC (SWR) pipes single socketed, in any length pipes single socketed, in any length with rubber ring joints, laid in trenches/fixed to walls with necessary clamps/placed in weep holes using synthetic rubber adhesive cement solvent complete all as specified and as directed.

S&F PVC (SWR) bends any radius, diameter of outlet 110 mm complete all as specified and as directed.

S&F PVC (SWR) bends any radius, diameter of outlet 75 mm complete all as specified and as directed.

S&F PVC (SWR) junction single, (Single T) equal or unequal, diameter of outlet 110 mm complete all as specified and as directed.

S&F PVC (SWR) junction single, (Single T) equal or unequal, diameter of outlet 75 mm complete all as specified and as directed.

S&F PVC (SWR) vent cowl of diameter 110 mm complete all as specified and as directed.

S&F PVC (SWR) vent cowl of diameter 75 mm complete all as specified and as directed.

S&F PVC (SWR) floor trap, plain with grating including jointing with solvent cement, diameter of outlet 75 mm, fixed in repairs complete all as specified and as directed.

S&F PVC (SWR) multi floor trap with grating including jointing with solvent cement, diameter of outlet 75mm, fixed in repairs complete all as specified and as directed.

S&F tubular towel rail, brass, chromium plated, 20mm dia, 60 cm long between flanges, fixed in repairs complete all as specified and as directed.

Taking down carefully old unserviceable aluminum/ copper point wiring (light, fan, socket or power) complete, including fittings & fixtures such as switches, ceiling roses, lamp holders, pendants, regulators sockets, light fittings, junction/terminal boxes etc; removing from site and making good disturbed surfaces of walls, floors etc., to match with existing surrounding surfaces complete all as specified and as directed.

Taking down existing unserviceable sub main wiring of any description and making good disturbed surfaces to match with existing surrounding finishes complete all as specified and as directed.

Taking down existing unserviceable main switches/ distribution boards of any description and making good disturbed surfaces to match with existing surrounding finishes complete all as specified and as directed.

Taking down carefully old unserviceable light fittings only and removing from site complete all as specified and as directed.

M&L for Point wiring complete with 1.5 Sqmm (nominal area) single core, PVC insulated unsheathed, FRLS cable, 1100 volts grade, multistranded copper conductor (with colour coding of Red/Blue/Yellow for phase and Black for neutral), drawn through and including rigid non metallic PVC conduit of suitable size (not less than 20mm dia) medium grade and conduit accessories concealed in walls/ceilings etc., including provision of PVC insulated 1.5 Sqmm FRLS cable with copper conductor green in colour for earth continuity and connected to common earth dolly and sunk in modular type pressed steel terminal boxes of suitable modules made out of 1.6mm thick MS sheet duly painted with two coats of anti-corrosive paint all over and modular cover plates with frames on top for suitable modules on top for housing switches, sockets etc., all as specified and as directed for ONE LIGHT/FAN point controlled by one, one way 6 Amps modular switch.

M&L for Point wiring complete with 1.5 Sqmm (nominal area) single core, PVC insulated unsheathed, FRLS cable, 1100 volts grade, multistranded copper conductor (with colour coding of Red/Blue/Yellow for phase and Black for neutral), drawn through and including rigid non metallic PVC conduit of suitable size (not less than 20mm dia) medium grade and conduit accessories concealed in walls/ceilings etc., including provision of PVC insulated 1.5 Sqmm FRLS cable with copper conductor green in colour for earth continuity and connected to common earth dolly and sunk in modular type pressed steel terminal boxes of suitable modules made out of 1.6mm thick MS sheet duly painted with two coats of anti-corrosive paint all over and modular cover plates with frames on top for suitable modules on top for housing switches, sockets etc., all as specified and as directed for TWO LIGHT points controlled by one, one way 6 Amps modular switches.

M&L for Point wiring complete with 1.5 Sqmm (nominal area) single core, PVC insulated unsheathed, FRLS cable, 1100 volts grade, multistranded copper conductor (with colour coding of Red/Blue/Yellow for phase and Black for neutral), drawn through and including rigid non metallic PVC conduit of suitable size (not less than 20mm dia) medium grade and conduit accessories concealed in walls/ceilings etc., including provision of PVC insulated 1.5 Sqmm FRLS cable with copper conductor green in colour for earth continuity and connected to common earth dolly and sunk in modular type pressed steel terminal boxes of suitable modules made out of 1.6mm thick MS sheet duly painted with two coats of anti-corrosive paint all over and modular cover plates with frames on top for suitable modules on top for housing switches, sockets etc., all as specified and as directed for ONE 6A SOCKET OUTLET point controlled by one, one way 6 Amps modular switch on independent board.

M&L for Point wiring complete with 1.5 Sqmm (nominal area) single core, PVC insulated unsheathed, FRLS cable, 1100 volts grade, multistranded copper conductor (with colour coding of Red/Blue/Yellow for phase and Black for neutral), drawn through and including rigid non metallic PVC conduit of suitable size (not less than 20mm dia) medium grade and conduit accessories concealed in walls/ceilings etc., including provision of PVC insulated 1.5 Sqmm FRLS cable with copper conductor green in colour for earth continuity and connected to common earth dolly and sunk in modular type pressed steel terminal boxes of suitable modules made out of 1.6mm thick MS sheet duly painted with two coats of anti-corrosive paint all over and modular cover plates with frames on top for suitable modules on top for housing switches, sockets etc., all as specified and as directed for ONE 6A SOCKET OUTLET point controlled by one, one way 6 Amps modular switch on same board with other switches.

M&L for Point wiring complete with 2.5 Sqmm (nominal area) single core, PVC insulated unsheathed, FRLS cable, 1100 volts grade, multistranded copper conductor (with colour coding of Red/Blue/Yellow for phase and Black for neutral), drawn through and including rigid non metallic PVC conduit of suitable size (not less than 20mm dia) medium grade and conduit accessories concealed in walls/ceilings etc., including provision of PVC insulated 2.5 Sqmm FRLS cable with copper conductor green in colour for earth continuity and connected to common earth dolly and sunk in modular type pressed steel terminal boxes of suitable modules made out of 1.6mm thick MS sheet duly painted with two coats of anti-corrosive paint all over and modular cover plates with frames on top for suitable modules on top for housing switches, sockets etc., all as specified and as directed for ONE 16A SOCKET OUTLET point controlled by one, one way 16 Amps modular switch on independent board.

M&L for Sub main wiring complete with two runs (1P+1N) of 6.0 Sqmm single core, PVC insulated unsheathed, FRLS cable, 1100 volts grade, multistranded copper conductor (with colour coding of Red/Blue/Yellow for phase and Black for neutral) and one run of 6.0 Sqmm single core, PVC insulated unsheathed, FRLS cable, 1100 volts grade, multistranded copper conductor as earth wire green in colour including lugs, drawn through and including 32mm wide rigid non-metallic PVC casing and capping and its accessories (OR) 25mm dia PVC conduit and conduit accessories fixed on surface of wall/ceiling/roof/ floor complete all as specified and as directed. NOTE: Two runs of 6.0 Sqm copper conductor, One run of 6.0 Sqmm copper conductor as earth wire and one run of PVC casing and capping / PVC conduit shall be measured as one unit length.

M&L for Sub main wiring complete with two runs (1P+1N) of 4.0 Sqmm single core, PVC insulated unsheathed, FRLS cable, 1100 volts grade, multistranded copper conductor (with colour coding of Red/Blue/Yellow for phase and Black for neutral) and one run of 4.0 Sqmm single core, PVC insulated unsheathed, FRLS cable, 1100 volts grade, multistranded copper conductor as earth wire green in colour including lugs, drawn through and including 32mm wide rigid non-metallic PVC casing and capping and its accessories (OR) 25mm dia PVC conduit and conduit accessories fixed on surface of wall/ceiling/roof/ floor complete all as specified and as directed. NOTE: Two runs of 4.0 Sqm copper conductor, One run of 4.0 Sqmm copper conductor as earth wire and one run of PVC casing and capping / PVC conduit shall be measured as one unit length.

M&L for LTUG XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cables (heavy duty) with aluminium conductor, 1100 volts grade, cross sectional area 2 core, 16 Sqmm laid in trenches/floors/ducts or fixed on poles/walls with suitable clamps/saddles or drawn through pipes etc., including connecting up with suitable size of lugs, glands and jointing material complete all as specified and as directed.

M&L for HDPE DWC (Double wall corrugated) pipe of size 77mm (Outer diameter) x 63mm (Inner diameter) along with connected accessories like couplers, bends, end caps etc., laid in trenches/floors/ducts or fixed on poles/walls for as in protection of LT/ HT cable complete all as specified and as directed.

S&F modular switch, one way, one module, single pole, 6 Amps complete all as specified and as directed.

S&F modular socket, multipurpose, 2/3 pin combined, 2 module, single pole, 6 Amps complete all as specified and as directed.

S&F modular socket, multipurpose, 2/3 pin, 6/16 Amps combined, 2 module, single pole, complete all as specified and as directed.

S&F modular switch, one way, one module, single pole, 16 Amps complete all as specified and as directed.

M&L for ceiling rose, three terminal, 65x20mm size, PVC/Polycarbonate, insulated body, 6A, 240 volts complete all as specified and as directed.

S&F ceiling fan of three blades metallic colour, remote controlled, 1200mm sweep, 360 RPM, suitable for AC 230 volts, heavy duty with down rod and canopies including provision of 3 core twisted copper conductor cable of suitable gauge from ceiling rose to connector of fan complete all as specified and as directed. MAKE: GORILLA Model: GOLDEN OAK WOOD

S&F wall mounting type oscillating air circulating fan, remote controlled, 400mm (16") sweep, 1330 RPM, working on 230 volts, 50 Hz, single phase, AC supply, heavy duty, aluminium alloy blades with double ball bearings, sturdy closed mesh guard protection complete with all accessories including provision of 3 core twisted copper conductor cable of suitable gauge with plug top from socket outlet to connector of fan complete all as specified and as directed. MAKE: GORILLA

S&F LED tube light fitting, 1x24 watts, 230 volts, 50Hz AC supply, with high power and high efficiency long life LEDs with built-in electronic driver, fixed on walls and provision of 3 core, 1.5 Sqmm copper cable from ceiling rose to connector of fitting complete all as specified and as directed. MAKE:CROMPTON Cat Part No. LDL-20-CDL or its equivalent in HAVELLS/BAJAJ

S&F LED security light fitting, 1x25 watts, 230 volts, 50Hz AC supply, with high power and high efficiency long life LEDs with built-in electronic driver, unique peanut lens to ensure uniform distribution completely housed including suitable down rod and fixed on walls including MS clamps (02Nos) made up of 40mmx5mm MS flat, nuts, bolts and washers and provision of 3 core, 1.5 Sqmm copper cable from ceiling rose to connector of fitting complete all as specified and as directed. MAKE:CROMPTON Cat Part No. LSTS-25-CDL-M or its equivalent in HAVELLS/BAJAJ

S&F MCB DB, SPN, 8-way, vertical type, double door, 240 Volts with 200 Amps rated bus bar, IP-43 protection, shrouded neutral bus bar, cement spill protector, concealed in wall and making good disturbed surfaces to match with surrounding surface complete all as specified and as directed. MAKE: L&T/ LEGRAND/ SIEMENS/ INDO ASIAN/ HAVELLS

S&F MCB, DP, "C" series, 230 volts, 40 Amps, 10 KA rupturing capacity complete all as specified and as directed. MAKE: INDO ASIAN Cat part No. 811174 or equivalent in L&T/ LEGRAND/ ABB/ HAVELLS

S&F MCB, SP, "C" series, 240 volts, 6 to 32 Amps, 10 KA rupturing capacity complete all as specified and as directed. MAKE: INDO ASIAN Cat part No. 811129 or equivalent in L&T/ LEGRAND/ ABB/ HAVELLS

S&F MCB, SPN, "C" series, 230 volts, 63 Amps, 10 KA rupturing capacity complete all as specified and as directed. MAKE: INDO ASIAN Cat part No. 811154 or equivalent in L&T/ LEGRAND/ ABB/ HAVELLS

S&F starter switch of capacity 25 Amps working on 240 Volts, AC supply suitable for split type airconditioner complete all as specified and as directed. MAKE: CRAB TREE Cat part No. ACTO252504 or equivalent in ANCHOR/HAVELLS/L&T

M&L for earthing complete with GI earth plate electrode of size 600mmx600mmx6mm thick buried directly in ground (earth pit not less than 2.25m deep below the normal ground level) with top edge of the earth plate not less than 1.5m below normal ground level connected to 4mm dia GI earth wire as earth lead connected by means of bolts, nuts, washers and check nuts made out of galvanised iron or steel all as shown on electrical plate No. 3 of SSR Part-I connected to common earth dolly including testing on completion complete all as specified and directed. NOTES: 1) The unit rate shall also include for earth work in any type of soil, PCC (1:3:6) type C1 chamber, pre-cast RCC (1:2:4) type B-1 using 20mm graded stone aggregate cover 50mm thick reinforced with TMT bars 8mm dia @ 100mm c/c both ways, funnel with watering pipe 20mm dia medium grade, GI protection pipe light grade 40mm dia and wire mesh complete in addition to item No. 1(a) to (e) of preamble (notes) under sub-heading earthing, specified on Sl. Page Nos. 422 & 423 of SSR Part-II. 2) Earthing lead and GI protection pipe beyond 7.5m will be measured and paid separately.

S&F decorative cute lines LED light fixture of 20 Watts capacity, 6000K, 230 Volts, 50 Hz AC supply, warm white with extruded aluminium heat sink, environmental friendly energy efficient light fitting, surface mounted including 20 Watts LED lamp and testing complete all as specified and as directed. MAKE: PHILIPS Cat part No. BN150WLED 20S-6500PSEODGR or equivalent in HAVELLS/ WIPRO/CROMPTON GREAVES

S&F wall mounting ebony decorative LED light fixture having stainless steel finish with opal glass diffuser suitable with built-in drivers for and including 9 Watts LED filament candle lamp, 230 Volts, 50 Hz AC supply and testing complete all as specified and as directed. MAKE: HAVELLS Cat part No. LHJE01106499 (Aristo) or equivalent in PHILIPS/CROMPTON GREAVES

S&F LED indoor lighting fixture having rount die-cast aluminium housing and high translucent frosted plastic diffuser with built-in drivers suitable for and including 18 Watts LED, 230 Volts, 50 Hz AC supply and testing complete all as specified and as directed. MAKE: CROMPTON GREAVES Cat part No. LCDSPLN-R-18-NW (Pearl NIOS-R) or equivalent in PHILIPS/ HAVELLS

S&F LED indoor lighting fixture recess mounting, compact vertical, round shaped down lighter with removable driver suitable for low ceiling heights with and including 9 Watts LED, 6500K, 230 Volts, 50 Hz AC supply and testing complete all as specified and as directed. MAKE: HAVELLS Cat part No. LHEBHDP7IZ1W009 or equivalent in PHILIPS/ CROMPTON GREAVES

S&F LED down light fixture of 12 Watts capacity with die-cast powder coated aluminium housing in-built driver, including 12 Watts LED lamp and testing complete all as specified and as directed. MAKE:CROMPTON GREAVES Cat part No. LSCRM-12W-CDL or equivalent in HAVELLS/ WIPRO/

M&L for security/street light mounting bracket made up of 40mm dia galvanised steel tubing, medium grade, 1.20 metres long, bent to shape with inner angle not less than 120°, with and including necessary fixing clamps fabricated out of angle iron/flat iron of suitable size, bolts, nuts and washers as required and applying two coats of aluminium paint over a coat of red oxide primer complete all as specified and directed.

SK CONSTRUCTION

DHAKSHNA MOORTHY AND SON

MS ASHOK T NAIR

Chandra Construction Enterprises

Ravi Enterprises