Tender for Supply and erection of 55 Nos. Galvanized Steel octagonal Pole (Sheet thickness 4mm to 5mm) with base plate Galvanized Octagonal Pole Overall Length 8metre i/c Single ARM Bracket 1.50 meter long , LED Flood Light luminaries 120 Watt wit

Supply and erection of Galvanized Steel octagonal Pole (Sheet thickness 4mm to 5mm) with base plate designed to withstand wind speec 169km/hour of suitable length Sheet Steel Confirming to IS 2062:2011 E350B0 (Yield Stress must be min 355 Mpa and Tensile Strengtt min 470 Mpa which is equivalent to BSEN-10025S- 355J or ASTM-572A (GR-50) and thickness of Hot dip galvanization coating (70 microns) conforming to 15:2629/ 1S:2633/ IS:4759, BSEN-ISO-1461- 1991 OR ASTM-A123/A123M-02. The pole shall be in single piece hot dip galvanized and shall be tapered towards the top. The bottom section shall have openable slot with exterior surface door & shall have suitable locking arrangement for housing three phase 4wire cable connection, bakelite sheet, MCB (0.4 to 5 Amp), loop in and out arrangement for incoming/ outgoing cables. There shall be uitable arrangement for earthing. Rigid Base plate of suitable size and thickness shall be welded inside and outside at the bottom of pole with provision for fixing 4 foundation bolts. The octagonal pole shal be bolted on a pre- cast foundation with a set of four foundation bolts of EN-8 Grade with thread portion hot dip galvanized for greate igidity. The foundation shall be erected over cement concrete M-10 with steel of given size as per design of original pole anufacturer to fixed up to a required planting depth below groundlevel as required: (i) Galvanized Octagonal Pole Overall Length 9.00 metre (Sheet thickness 4mm to 5 mm), Top dia. 70mm and bottom dia.180 mm, foundation size below G/L 600mm x 600mm x 1700mm, 4Nos. Foundation Bolts size 30mm dia, Length 2750 mm with Base Plate Dimensions 260mm x 260mm x 16mm Thick. (ii) Single ARM Bracket 1.50 meter long for galvanized octagonal. (iii) GI Earth rod 20 mm dia, 3 mtr Long. (iv) Earth work in excavation in foundations trenches etc. ( v) Cement concrete 1:3:6, with stone aggregate 20 mm gauge mixing by manual means . (vi) Earthing with S.W.G (7/2.80mm dia ) G.I rope in 20 mm dia pipe with G.I reducing socket 50mm x 20mm ( upto 9 meter in length) in all respect including carriage of material with in all leads lifts complete in all respects as per the direction and to be entire satisfaction of Engineer-in-Charge.

Fabrication,Supply,Installation,Testing ana Commissioning of Street Light cum Energy Meter Pane suitable for incorporating Digital time Switch, Contactors, Aluminium Bus Bar Chamber with suitable numoer of AL BUs Bars, MCCB, MCBS erc as per quantities/ratings mentioned below for distribution of supply to tne individual street lights. . All wiring powder coated of approved shade Item includes construction of work from Bus bar to MCCE shall be completed in the panel manufacturer's Premises approva of EIC where panel has to be erected. The items includes the cost to foundation for panel of suitable size ds DEl concrete as required at site for suitable grouting of Panel. (For Commercial area Type, Duly Compartmantalised with Double Door Arrangement outaoor Usage Cubical, only. Degree of Protection -Min IP 54 C rype CRCA sheet Steel 2.00 Mm Materla Should be with 75x40x4mm Channe Iror High Mast No. Showing strips should be attched on Base of panel Panel No. showing strip should be attached on outer plate Marking Inner Doors of respective cabins Aluminium Bus Bar suitable for Current Rating of 100 Amp - 4 Nos 25 KA Breaking Capacity- 1 Nos MCCB, 100 Amp 4 POI MCB, 63Amp, 4pole 10 kA Breaking Capacity, Curve C-Pnos Digital Tīme Switch Dally Programm with Stand by battery (3years/6years) on Channel 2Nos 3phase energy meter for all 55 Nos. pole space for Installation -including cornection strips (The energy Meter will be installed by the MCB, 63Amp, 2pole, 10 kA BreakIng Capacity, Curve C-3nos individual consumers/PSPCL at their MO Locking arrangement- Godrej Type Concealed Lock R.Y.B protected with 0.5A to 4A Single Pole MCB wiring should be with 2 core 16 Sq.mm under ground with DWC pipe of 50mm dia cover with proper depth i/c 40 meter cable for each pole, Street light control box,time box with complete system, Phase Indicators-3 SON cade as :- (i) MCB four pole 63amp of Havells make. (10kA, Curve -c) (ii) MCB Single pole 6-32amp. (10kA, Curve -c) (iii) Earthing with S.W.G (7/2.80mm dia) G.I rope in 20 mm dia pipe with G.I reducing socket 50mm x 20mm ( upto 9 meter in length) (iv) S,I,T,C of out door LED Flood Light luminaries 120 watt ISI mark of Philips/Havells make with detailed specitications and to the entire satisfaction of ElC. Reducer/Enlarger if required for erection of LED Lights is included in rates of Lights. in all respect including carriage of material with in all leads lifts complete in all respects as per the direction and to be entire satisfaction of Engineer-in-Charge.