Construction of Lawyer's Hall at Sub-Divisional Court Campus Narkatiaganj, Bettiah, Distt. West Champaran.

GOVERNMENT OF BIHAR

BUILDING CONSTRUCTION DEPARTMENT

NAME OF DIVISION :- BUILDING DIVISION, BETTIAH

BILL OF QUANTITY

Name of work:- Construction of Lawyer's Hall at Sub-Divisional Court Campus Narkatiaganj, Bettiah, Distt. West Champaran.

AMOUNT OF B.O.Q ₹ 6,838,926.00

EARNEST OF B.O.Q ₹ 136,800.00

COST OF B.O.Q. ₹ 10,000.00

BID PROCESSING FEE As Per Online Requirement Main B Septic Tank Boring Sanitary

S.No. Code Items Qty. Unit Rate Amount Qty Amount Qty Amount Qty Amount Qty Amount

1 2.29.1 Surface dressing of the ground including removing vegetation and inequalities not exceeding 15 cm deep and disposal of rubbish, lead upto 50 m and lift upto 1.5 m All kinds of soil. 600.000 100m2 1,355.40 8,132.00 600 8,132.00 0.00 0.00 0.00

2 20.2.2 Boring, providing and installing bored cast-in-situ reinforced cement concrete piles of grade M-25 of specified diameter and length below the pile cap, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring, with bentonite solution and temporary casing of appropriate length for setting out and removal of same and the length of the pile to be embedded in the pile cap etc. all complete, including removal of excavated earth with all lifts and leads (Length of pile for payment shall be measured upto bottom of pile cap).400 mm dia piles 550.200 m 1,163.30 640,048.00 550.2 640,048.00 0.00 0.00 0.00

3 2.8.1 Earth work in excavation in foundation trenches or drains(not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m . including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All Kinds of soil 232.070 m3 360.70 83,708.00 211.372 76,242.00 17.548 6,330.00 3.15 1,136.00 0.00

4 2.26 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth: consolidating each deposited layer by ramming and watering lead 126.813 m3 123.90 15,712.00 126.813 15,712.00 0.00 0.00 0.00

5 2.28 Supplying and Filling in plinth with local sand and under floors including, watering, ramming consolidating and dressing complete. 105.093 m3 287.30 30,193.00 103.84 29,833.00 1.253 360.00 0.00 0.00

6 11.72 Providing designation 100 A one brick flat soling joints filled with local sand including cost of watering, taxes, royalty all complete as per building specification and direction of E/l, 309.426 m2 283.30 87,660.00 301.07 85,293.00 8.356 2,367.00 0.00 0.00

7 4.1.5 Providing and laying in position cement concrete of specified grade exluding the cost of centring and shuttering-all work upto plinth level. 1:3:6 (1 Cement: 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) 20.040 m3 3,434.00 68,817.00 19.204 65,947.00 0.836 2,871.00 0.00 0.00

8 6.1.14C Brick work with fly ash bricks as per IS 12894(2002) & IS 3495 in foundations and plinth in : Cement mortar 1:6 (1 cement: 6 coarse sand ) 15.087 m3 4,923.00 74,273.00 15.087 74,273.00 0.00 0.00 0.00

9 6.1.14C +6.3C Brick work with fly ash bricks as per IS 12894(2002) & IS 3495 in foundations and plinth in : Cement mortar 1:6 (1 cement: 6 coarse sand ) Extra tor Brick work in superstructure above plinth level upto floor V cum 37.758 m3 5,765.20 217,682.00 37.758 217,682.00 0.00 0.00 0.00

10 6.1.12C +6.3C Brick work with fly ash bricks as per IS 12894(2002) & IS 3495 in foundations and plinth in : Cement mortar 1.:4 (1 cement: 4 coarse sand ) Extra tor Brick work in superstructure above plinth level upto floor V cum 4.652 m3 5,958.50 27,719.00 4.652 27,719.00 0.00 0.00 0.00

11 6.1.12C +6.1C Brick work with fly ash bricks as per IS 12894(2002) & IS 3495 in foundations and plinth in : Cement mortar 1.:4 (1 cement: 4 coarse sand ) 6.262 m3 5,116.30 32,038.00 0 0.00 6.262 32,038.00 0.00 0.00

12 5.33.1.1 Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana /Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate /retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. All works up to plinth level Concrete of M-25 grade with minimum cement content of 330 kg/cum 67.830 m3 5,063.40 343,450.00 67.83 343,450.00 0.00 0.00 0.00

5.33.2.1 Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana /Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate /retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. All work above Plinth level upto floor V Level. Concrete of M-25 grade with minimum cement content of 330 kg/cum 55.603 m3 5,863.20 326,012.00 55.603 326,012.00 0.00 0.00 0.00

13 5.22 Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete. 0.000 0.00 0.00 0.00 0.00 0.00

5.22.7A Thermo-Mechanically Treated bars TMTC-500-8mm dia. 5,781.000 kg 94.50 546,305.00 5781 546,305.00 0.00 0.00 0.00

5.22.7B Thermo-Mechanically Treated bars TMTC-500-10mm dia. 2,020.000 kg 92.60 187,052.00 1926 178,348.00 94.000 8,704.00 0.00 0.00

5.22.7C Thermo-Mechanically Treated bars TMTC-500-12mm dia. 3,854.000 kg 90.80 349,943.00 3854 349,943.00 0.00 0.00 0.00

5.22.7D Thermo-Mechanically Treated bars TMT Fe-500-I6mrn dia. 5,781.000 kg 91.70 530,118.00 5781 530,118.00 0.00 0.00 0.00

5.22.7E Thermo-Mechanically Treated bars TMT Fe-500-20mm dia. 1,927.000 kg 91.70 176,706.00 1927 176,706.00 0.00 0.00 0.00

14 5.9.1 Centring and shuttering including strutting,propping etc. and removal of form for. Foundations, footings, bases of columns etc. for mass concrete. 127.500 m2 211.60 26,979.00 118.744 25,126.00 8.756 1,853.00 0.00 0.00

15 5.9.3 Centring and shuttering including strutting,propping etc. and removal of form for. Suspended floors, roots, landings, balcnies and access platform. 126.808 m2 437.50 55,479.00 126.808 55,479.00 0.00 0.00 0.00

16 5.9.5 Centring and shuttering including strutting,propping etc. and removal of form for. Lintels, beams, plinth bams, griders, bressumers and contilevers. 234.838 m2 404.70 95,039.00 234.838 95,039.00 0.00 0.00 0.00

17 5.9.6 Centring and shuttering including strutting,propping etc. and removal of form for. Columns,Pillars, Piers, Abutments, Posts and Struts 178.360 m2 494.40 88,181.00 178.36 88,181.00 0.00 0.00 0.00

18 5.9.7 Centring and shuttering including strutting,propping etc. and removal of form for. Stairs,(excluding landings) except spiral-staircaces. 18.308 m2 439.90 8,054.00 18.308 8,054.00 0.00 0.00 0.00

19 5.9.19 Centring and shuttering including strutting,propping etc. and removal of form for. Weather shade,Chajjas, corbels etc. including edges 9.990 m2 550.90 5,503.00 9.99 5,503.00 0.00 0.00 0.00

20 5.9.16.1 Centring and shuttering including strutting,propping etc. and removal of form for. Edges of slabs and breaks in floors and walis- Under 20 cms wide 56.162 m 130.20 7,312.00 56.162 7,312.00 0.00 0.00 0.00

21 10.15.1.1 Providing and fixing pressed steel door confirming IS code 4351 manufactured from commerical mild steel sheet of 1.25 mm thickness including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50 x 25 mm or base ties of 1.25mm pressed mild steel welded or rigidly fixed together by mechnical means, adjustable lugs with split end tail to each jamb including steel butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge: Profile B Fixing with adjustable lugs with split end tail to each jamb 46.650 m 405.80 18,931.00 46.65 18,931.00 0.00 0.00 0.00

22 9.20.1 Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1 st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 35 mm thick including stainless steel butt hinges with necessary screwssqm 18.585 m2 2,845.60 52,885.00 18.585 52,885.00 0.00 0.00 0.00

23 9.101.2 Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. Twin rubber stopper 8.000 Nos 60.80 486.00 8 486.00 0.00 0.00 0.00

24 9.62.2 Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete : 250x16 mm 8.000 Nos 154.40 1,235.00 8 1,235.00 0.00 0.00 0.00

25 9.63.2 Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete: 200x10 mm 8.000 Nos 56.40 451.00 8 451.00 0.00 0.00 0.00

26 9.66.2 Providing and fixing ISI marked oxidised M.S. handles conforming to IS :4992 with necessary screws etc. complete: 100 mm 16.000 Nos 25.50 408.00 16 408.00 0.00 0.00 0.00

27 10.12.1 Providing and fixing steel glazed doors, windows and ventilatrs of standard rolled steel sections, joints mitered and welded with 15x3 mm lugs 10 cm long with steel lugs embedded in cement concrete blocks 15x10x10 cm of 1:3:6(1 cement: 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) or with woodenplugs and screws or raw) plugs and screws or with fixing dips or with bolts and nuts as required, including providing and fixing of glass panes with glazing dips and special metal-sash putty pf approved make complete including applying a priming coat of approved steel primer; excluding the cost of metal beading and other fitting except necessary hinges or pivots as required. Doors 29.655 m2 3,038.90 90,119.00 29.655 90,119.00 0.00 0.00 0.00

28 9.48.2 Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to openings/ wooden frames with rawl plugs screws etc 496.908 kg 161.10 80,052.00 496.908 80,052.00 0.00 0.00 0.00

29 10.33.1 Providing and fixing hand rail by welding etc. to steel ladder railings & staircases railing including applying a priming coat of approved steel primer MS tube (medium) 40mm nominal bore 29.340 kg 121.90 3,577.00 29.34 3,577.00 0.00 0.00 0.00

30 10.18 Providing and fixing circular/hexagonal cast iron or M.S sheet box for ceiling fan clamp 140 mm internal dia, 73 mm height, 5 mm thick rim bottom and top lids, 1.5 mm thick M.S sheet with its top surface hacked for proper bonding top lid shall be screwed into the cast iron box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamps shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing. 10.000 Nos 165.40 1,654.00 10 1,654.00 0.00 0.00 0.00

31 11.37 Providing and laying Ceramic glazed floor tiles 300x300 mm (thickness to be specified by the manufacturer) of ist quality conforming to IS : 15622 of approved make in colours such as white , Ivory , Grey , Fume Red , Brown , laid on 20 mm thick Cement motar 1:4 (1 cement: 4 coarse sand ) including pointing the joints with white cement and matching pigment etc., complete. 16.895 m2 686.80 11,603.00 16.895 11,603.00 0.00 0.00 0.00

32 11.36 Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS : 15622 (Thickness to be specified by the manufacture) of approved make in all colours, shades except burgundy , bottle green , black of any size as approved by Engineer-in-charge in skirting , risers of steps and dados over 12 mm thick bed of cement Motar 1:3(1 cement: 3 coarse sand ) and jointing with grey cement slurry @ 3.3 kg per sqm including pointing in white cement mixed with pigment of matching shade complete. 55.020 m2 795.00 43,741.00 55.02 43,741.00 0.00 0.00 0.00

33 11.26.1 Kota stone slab flooring over 20 mm (average ) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete . Base with 1:1:1 (1 lime : 1 surkhi: 1 coarse sand ) / 1:4 (1 cement: 4 coarse sand ) 20 to 25 mm thick - 140.570 m2 1,252.70 176,092.00 140.57 176,092.00 0.00 0.00 0.00

34 11.27 Kota stone slabs 20 mm thick in risers of steps skirting. Dado & pillars laid on 12 mm (average (thick cement mortar 1:3 (1 cement: 3 coarse sand ) and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete. Details of cost for 10 sqm SAND STONE FLOORING 12.500 m2 1,334.90 16,686.00 12.5 16,686.00 0.00 0.00 0.00

35 13.11.4 Cement plaster in course sand 12 mm cement plaster of mix: 1:6(1 cement: 6 coarse sand) 356.050 m2 141.50 50,381.00 356.05 50,381.00 0.00 0.00 0.00

36 13.12.4 15 mm cement plaster on rough side of single or half brick wall of mix. 1:6 (1 cement: 6 coarse sand) 319.343 m2 162.80 51,989.00 319.343 51,989.00 0.00 0.00 0.00

37 13.24.2 6 mm cement plaster to ceiling of mix : 1:4(1 cement: 4 coarse sand) 151.131 m2 125.60 18,982.00 151.131 18,982.00 0.00 0.00 0.00

38 13.18 15 mm cement plaster 1:3 (1 cement: 3 coarse sand ) finished with a floating coat of neat cement on the rough side of single or half brick wall. 64.369 m2 229.30 14,760.00 64.369 14,760.00 0.00 0.00 0.00

39 13.80A.2 Providing and applying white cement based putty of average thickness 2 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. 470.324 m2 105.40 49,572.00 470.324 49,572.00 0.00 0.00 0.00

40 13.79.1+ 13.78.1 Finishing walls with water proofing cement paint of approved brand and manufacture and of required shade to give an even shade New work (three or more coats) Applying one coat of cement primer of approved brand and manufacture on wall surface: Cement primer 366.040 m2 119.80 43,852.00 366.04 43,852.00 0.00 0.00 0.00

41 13.77.2 Distempering with oil bound washa ble distemper of approved brand and manufacture to give an even shade . New work (two or more coats ) over and including priming coat with cement primer 460.334 m2 102.30 47,092.00 460.334 47,092.00 0.00 0.00 0.00

42 13.81.3+ 13.82.1 Applying priming coat: With ready mixed zinc chromate yellow primer of approved brand and manufacture on steel galvanized iron/steel works Painting with ready mixed paint of approved brand and manufacture in all shades to give an even shade: New steel work (two or more coats) 41.409 m2 118.10 4,890.00 41.409 4,890.00 0.00 0.00 0.00

43 12.78 Providing and fixing on wall face unplastidsed-PVC(working pressure 4 kgf per sqm) rain water pipes conforming to IS :4985 including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion.110 mm dia pipe 0.000 0.00 0.00 0.00 0.00

44 12.79 Providing and fixing on wall face unplasticised -PVC molded fittings/accessories for unplasticised-PVC rain water pipes conforming to (S:4985 including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion. 0.000 0.00 0.00 0.00 0.00

45 12.80. Providing and fixing unplasticised -PVC pipe clip of approved design to unplasticised PVC rain water pipe by means of 50x50x50mm hard wood plugs, screwed with M.S. screws of required length including cutting brick work and fixing on cement mortar(1:4) 1 cement: 4corsa sand and making good the wall etc complete.110 mm 0.000 0.00 0.00 0.00 0.00

46 12.81 Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams. 4.000 each 47.90 192.00 4 192.00 0.00 0.00 0.00

47 Carraige cost of material 0.00 0.00 0.00 0.00

48 Extra cost of material 0.00 0.00 0.00 0.00

49 5.33A.1 Providing and laying in position machine batched, machine mixed and machine vibrated design mix cement concrete of specified grade for reinforced cement concrete structural elements, excluding the cost of centring, shuttering finishing and reinforcement, M-20 grde reinforcd cement concrete All work upto plinth level 1.156 m3 4,756.90 5,499.00 0.00 1.156 5,499.00 0.00 0.00

50 13.18+ 13.36.3 15 mm cement plaster 1:3 (1 cement: 3 coarse sand ) finished with a floating coat of neat cement on the rough side of single or half brick wall. Extra for providing and mixing water proofing material in proportion recommended by the manufacturers: 15 mm cement plaster 1:3(1 cement :3 sand) 43.515 m2 239.60 10,426.00 0.00 43.515 10,426.00 0.00 0.00

52 OL01 Labour required for Brick bats 2.000 No 355.42 711.00 0.00 2.000 711.00 0.00 0.00

53 24.1.1.1 Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer -in-charge, upto 90 metre depth below ground level. All types of soil 300 mm dia 40.000 m 486.80 19,472.00 0.00 0.00 40 19,472.00 0.00

54 24.3.1 Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths,as per direction of Engineer -in-charge. 100 mm nominal size dia 36.000 m 546.10 19,660.00 0.00 0.00 36 19,660.00 0.00

55 24.4.1 Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge. 100 mm nominal size dia 6.000 m 573.10 3,439.00 0.00 0.00 6 3,439.00 0.00

56 24.8 Gravel packing in tubewell construction in accordance with IS: 4097,including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineer-in-charge. 2.121 m3 1,343.20 2,849.00 0.00 0.00 2.121 2,849.00 0.00

57 24.10.1 Supplying, assembling, lowering and fixing in vertical position in bore well, ERW (Electric Resistance Welded) FE 410 mild steel screwed and socketed/ plain ended casing pipes of required dia,conforming to IS: 4270, of reputed & approved make, including painted with outside surface with two coats of anticorrosive paint of approved brand and manufacture, including required hire & labour charges, fittings & accessories, all complete, for all depths, as per direction of Engineer-incharge. 100 mm nominal size dia having minimum wall thickness 5.00 mm 1.000 m 1,121.20 1,121.00 0.00 0.00 1 1,121.00 0.00

58 24.13.1 Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of: 100 mm dia 1.000 No 189.70 190.00 0.00 0.00 1 190.00 0.00

59 24.14.1 Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete. 100 mm clamp 1.000 No 1,448.40 1,448.00 0.00 0.00 1 1,448.00 0.00

60 24.15.1 Providing and fixing Bail plug/ Bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS:2800 (part I). 100 mm dia 1.000 No 228.30 228.00 0.00 0.00 1 228.00 0.00

61 24.12 Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully develo ped, measuring yield of well by "V" notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tubewell, all complete,including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge. 8.000 hours 916.80 7,334.00 0.00 0.00 8 7,334.00 0.00

62 18.9 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement ,trenching ,refilling & testing of joints complete as per direction of Engineer in Charge. 40 mm nominal outer dia Pipes 0.00 0.00 0.00 0.00

63 NS Supplying installation testing and commisioning submersible motor 1 H.p motor with Cable all complete, including hire & labour charges of accessories etc., all as per requirement and direction of Engineer-in-charge. 1.000 no 20,000.00 20,000.00 0.00 0.00 1 20,000.00 0.00

64 18.8 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 0.00 0.00 0.00 0.00

65 18.19 Providing and fixing gun metal non- return valve of approved quality (screwed end) : 25 mm nominal bore 0.00 0.00 0.00 0.00

66 18.18.3 Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete 25 mm nominal bore 1.000 each 399.20 399.00 0.00 0.00 0.00 1 399.00

67 18.17 Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 0.00 0.00 0.00 0.00

68 18.48 Providing and placing on terrace (at all floor levels) polyethylene water storage tank, ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. 1,000.000 Ltr. 9.70 9,700.00 0.00 0.00 0.00 1000 9,700.00

69 18.49 Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 3.000 No. 434.20 1,303.00 0.00 0.00 0.00 3 1,303.00

70 18.53.1 Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 a) 15 mm nominal bore 15 mm nominal bore 4.000 No. 500.40 2,002.00 0.00 0.00 0.00 4 2,002.00

71 18.52.1 Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. 15 mm nominal bore 4.000 No. 594.80 2,379.00 0.00 0.00 0.00 4 2,379.00

72 18.74.2 Providing and fixing unplasticised P.V.C. connection pipe with PTMT Nuts, collar and bush of approved quality and colour. 15 mm nominal bore with 45 cm length 3.000 No. 108.00 324.00 0.00 0.00 0.00 3 324.00

73 18.75.3 Providing and fixing PTMT extension nipple for water tank pipe, fittings of approved quality and colour. 25mm nominal bore, weighing not less than 62 gms 1.000 No. 100.60 101.00 0.00 0.00 0.00 1 101.00

74 17.71 Providing and fixing PTMT liquid soap container 109 mm wide,125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms. 3.000 No. 146.30 439.00 0.00 0.00 0.00 3 439.00

75 17.72 Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour,weighing not less than 88 gms. 3.000 No. 204.70 614.00 0.00 0.00 0.00 3 614.00

76 17.7.1 Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require : White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps 3.000 No. 2764.40 8,293.00 0.00 0.00 0.00 3 8,293.00

77 17.28 Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. 0.00 0.00 0.00 0.00

78 17.34.1 Providing and fixing toilet paper holder C.P. brass 3.000 No. 550.70 1,652.00 0.00 0.00 0.00 3 1,652.00

79 17.1.1 Providing and fixing water closet squatting pan (Indian type W.C.pan ) with 100 mm sand cast Iron P or S trap, 10 litre low fixtures complete, including cutting and making good the walls andlevel white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and floors wherever required : White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests 2.000 No. 4470.90 8,942.00 0.00 0.00 0.00 2 8,942.00

80 17.3.1 Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I.brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid 1.000 No. 5504.30 5,504.00 0.00 0.00 0.00 1 5,504.00

81 17.4.1 Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : One urinal basin with 5 litre white P.V.C. automatic flushing cistern 1.000 No. 3723.20 3,723.00 0.00 0.00 0.00 1 3,723.00

82 17.16A Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge. 1.000 No. 299.40 299.00 0.00 0.00 0.00 1 299.00

83 NS Providing and fixing Brab Bar in W.C for P.H 1.000 1000.00 1,000.00 0.00 0.00 0.00 1 1,000.00

84 Providing and fixing CO2 fire extinguisher consisting of seamless MS cylindrical body squeeze lever discharge valve, internal discharge tube, 30 cms long high pressure discharge hose, discharge nozzle ISI marked as per IS 13869 including fixing with dash fasteners etc. complete. MAKE: OMEX/ NEWTECH/ EQV. (a) Capacity 4.5 kg. 2.000 Each 9,500.00 19,000.00 0.00 0.00 0.00 0.00

85 Providing and fixing ABC fire extinguisher consisting of seamless MS cylindrical body squeeze lever discharge valve, internal discharge tube, 30 cms long high pressure discharge hose, discharge nozzle ISI marked as per IS 13869 including fixing with dash fasteners etc. complete. MAKE: OMEX/ NEWTECH/ EQV. (a) Capacity 4.5 kg. 2.000 Each 6625.00 13,250.00 0.00 0.00 0.00 0.00

Total SOR+DSR 5,803,311.00

Total NS 405,438.00

CORRECTION FACTOR @.982 ON SOR& DSR 5,698,852.00

Total Civil Work (A) 6,409,749.00

Electric Work 123,563.00 5114

1 1.3 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit with modular switch , modular plate, suitable size G.I. box etc as required.

Angle Holder Point 11

Street Light Point 4

2 1.31 Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection etc. as required. 6 Each 414.00 2,484.00

3 1.55 Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 2 nos. 3 pin 5/6 amps modular socket outlet and 2 nos. 5/6 amps modular switch, connection etc. as required. 8 Each 632.00 5,056.00

4 1.57 Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 4 nos. 5 pin 5/6 amps modular socket outlet and 4 nos. 5/6 amps modular switch, connection etc. as required. 3 Each 1064.00 3,192.00

5 1.53 Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess including providing and fixing 25 amps modular socket outlet and 25 amp modular SP MCB 'C' curve, including connections, painting etc. as required. 3 Each 683.00 2,049.00

6 1.32 Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess including providing and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps modular switch, connection etc. as required. 5 Each 531.00 2,655.00

7 5.7 Supplying and fixing recess mounted following types LED downlighter with minimum efficacy 100 lm/w in pressure die-cast aluminium housing and integrated electronic driver etc directly on ceiling including connections with 1.5 sq.mm FRLS PVC insulated copper conductor cable etc as required. 0.00

8 1.34 Supplying and fixing batten/ angle holder including connection etc. as required. 6 Each 80.00 480.00

9 5.1 Supplying and fixing 4'X18 watt LED batten with minimum efficacy 100 lm/w in polycarbonate housing and complete with integrated electronic driver etc directly on wall/ ceiling including connections with 1.5 sq.mm FRLS PVC insulated copper conductor etc. as required. 8 Each 521.00 4,168.00

10 6.1 Supplying and fixing of following types lamp in the existing electrical fitting/ fixtures etc. as required. 0.00

6.1.4 9/10 watt LED lamp 11 Each 161.00 1,771.00

11 1.33 Supplying and fixing 2 pin, 5/6 amp ceiling rose on the existing junction box/ wooden block including connection etc as required. 41 Each 64.00 2,624.00

12 1.7 Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 0.00

1.7.1 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire 130 Meter 201.00 26,130.00

1.7.2 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire(FOR CT(165m) AND STREET LIGHT(40m)) 205 Meter 246.00 50,430.00

1.7.3 2 X 4 sq. mm + 1 X 4 sq. mm earth wire 45 Meter 309.00 13,905.00

1.7.12 4 X 10 sq. mm + 1 X 6 sq. mm earth wire 40 Meter 925.00 37,000.00

13 1.5 Wiring for light/ power plug with 2 X 4 sq. mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit along with 1 Nos 4 sq. mm FR PVC insulated copper conductor single core cable for loop earthing as required. 75 Meter 309.00 23,175.00

14 2.9 Supplying and fixing following way, horizontal type three pole & neutral, sheet steel, MCB distribution board, 415 volts, on surface/ recess, complete with tinned copper bus - bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 0.00

2.9.1 4 way ( 4 + 12 ), Double door, horizontal type 2 Each 4184.00 8,368.00

15 2.12 Supplying and fixing following rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. 0.00

2.12.1 6 A to 32 A, Single pole 24 Each 237.00 5,688.00

16 2.12 Supplying and fixing following rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. 0.00

17 8.15 Supply and installation of regular/standard model A.C. ceiling fan of 1200 mm sweep with service value (CM/MM) minimum 4.00, Air delivery minimum 210 cum/min including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated copper conductor etc as required. 17 Each 2482.00 42,194.00

18 1.25 Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate/ switch box including connections but excluding modular plate etc. as required. 17 Each 358.00 6,086.00 5,673,025.00 84,658.00

19 8.17 Supply and installation of following sweep/ sizes metallic blade, heavy duty, single phase, 230 V A.C. Exhaust Fan in existing opening including making good the damage, connection, testing and commissioning etc as required. 0.00 5,674,727.00

20 5.14 Supplying and fixing following types LED street light with minimum efficacy 100 lm/w in die cast aluminium housing, toughened glass, IP 66 protection and complete with electronic driver etc on pole/building including connection earthing the body etc as required. 0.00

21 8.4 Supplying and embedding following dia G.I. pipe (medium class) in pole collar/ foundation (during casting) for cable entry including bending the pipe to the required shape complete as required. 0.00

22 8.11 Supply and fixing of fabricated Electrical control panel of cubical construction, floor/wall mounted type, fabricated out of 16 SWG CRCA sheet, compartmentalised with hinged doors, dust and vermin proof, powder coated painting of approved shade after 7 tank treatment process, cable alley, internal wiring, earth terminals, Bus bar Chamber, insulator and complete in all respect etc and panel manufactures must be approved by CPRI. (But without RYB inicator, ammeter, voltmeter, inter-connection copper conductor cable/solid copper strip, switchgears etc.) 6 Sq.ft. 1809.00 10,854.00

A/R Supplying of copper strip of all sizes for busbar strip/interconnection including drilling holes etc as reqd. 3 kg 871.00 2,613.00

23 2.4 Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections etc. as required. 0.00

24 2.7 Providing and fixing following capacity four pole ON-load/ panel mounted changeover switches inside the existing cubical panel board including drilling holes in cubicle panel, making connections etc. as required. 0.00

25 2.12 Supplying and fixing following rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. 0.00

26 8.13 Supply and fixing panel mounted digital multimeter (Voltmeter & ammeter) including CT coil and RYB pilot indictor in the existing cubical panel board including drilling holes in the panel board making connections etc as required. 1 Each 6536.00 6,536.00

27 7.7 Supply of following sizes and core PVC/XLPE insulated, PVC sheathed (heavy duty) armoured electrical power cable with aluminium conductor for working voltage upto 1.1 KV as required. 0.00

28 7.4 Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required. 0.00

7.4.1 Upto 35 sq. mm (Clamped with 1 mm thick saddle) 65 Metre 43.00 2,795.00

29 3.1 Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc. ( but without charcoal/ coke and salt ) as required. 2 Set 5033.00 10,066.00

30 3.18 Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required. 30 Metre 31.00 930.00

Total Electric Work (B) 429,177.00

Total Civil Work (A)+Total Electric Work (B) 6,838,926.00