Various Construction work in New nursery Creation Range Chhabra

Clearing jungle including uprooting of rank vegitation ,grass,brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removel of rubbish up to a distance of 50m outside the periphery of the area cleared

Earth work in excavation by mechanical means (hydraulic excabator ) manual means over areas ( exceeding 30 cm in deapth 1.5 m in width or 10 sqm on plan) icluding excavated earth, lead upto 50m and lift upto 1.50m disposal earth to be levelled and neatly dressed ,all kinds of soil

Providing and laying in position cement comcrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering all work up ti plinth level, 1:5:10 (1 cemet : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size

Random Rubble stone masonry for foundation and plinth in Cement Sand mortar above 30 cm thick wall in : Cement Mortar 1 : 6 (1-Cement : 6-Sand).

Random Rubble stone masonry for superstructure above plinth level one storey height above 30 cm. thick walls in : Cement Mortar 1 : 6 (1-Cement : 6-Sand).

Plaster on new surface on stone masonary in cement sand mortar 1:3 including racking of joints etc. complete fine finish 25 mm thick

Pointing on stone masonry in cement sand mortar 1 : 3 (1 cement : 3 sand) : flush / ruled

Providing and laying damp proof course with cement concrete Grade M-150(1:2:4) Mortar prepared with 1 % soluition of water proof compound complete as per specification 50 mm thick

Providing & Fixing of energy efficient /energy saving IP 20 LED direct retrofit Bulb in existing holder or fixture as required with system lumen efficacy ≥100 lm/Watt output ,pf 0.95 , CRI >70, minimum life time of minimum 25000 Burning Hours with , 70% of intial Lumen maintaned till life ends , CCT 3000°K / 4000°K / 5700°K /6000°K/6500°K (As per ANSI Bin) , maximum power consumption should not more than the specified rating and Fixture shall be of BIS standard and trade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. OEM must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79/LM80) certificate / Report from OEM shall be submitted. All as per pre approved by engineer in charge . for additional technical parameters of product/ work, refer Annexure A attacheded with this BSR. 9 Wa

Random Rubble stone masonry for superstructure above plinth level one storey height above 30 cm. thick walls in : Cement Mortar 1 : 6 (1-Cement : 6-Sand).

Plaster on new surface on stone masonary in cement sand mortar 1:3 including racking of joints etc. complete fine finish 25 mm thick

Pointing on stone masonry in cement sand mortar 1 : 3 (1 cement : 3 sand) : flush / ruled

Providing and laying damp proof course with cement concrete Grade M-150(1:2:4) Mortar prepared with 1 % soluition of water proof compound complete as per specification 50 mm thick

Earth work in excavation by mechanical means (Hydraulic excavator ) manual over areas (exceeding 30 cm in depth, 1.5m in width as well as 10 sqm on plan ) including disposal of excavated earth, lead upto 50m and lift upto 1.5 m disposed earth to be levelled and neatly dressed. All kinds of soil

Providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering - All work up to plinth level. 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size.)

Random Rubble stone masonry for with hard stone in foundation and plinth in Cement Sand mortar above 30 CM thick wall in: Cement Mortar 1:6 ( 1-Cement : 6-Sand).

Brick work with F.P.S. bricks of class designation 75 in superstructure above plinth level upto floor V level in all shapes and sizes in : Cement mortar 1:6 (1 cement : 6 coarse sand )

Centering & Shuttering with plywood or steel sheets including strutting, propping bracing both ways with steel props and removal of formwork for upto floor five level for : Suspended floors, roofs, landings, staircases, balconies, girders, cantilevers, bands, coping bed plates, anchor blocks, sills, chhajjas, lintel, beam, plinth beam etc.

Providing and laying in position specified grade of cement concretee for RCC structural elements upto floor five level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers (if required ) excluding the cost of centering, shuttering and reinforcement for Walls (any thickness) including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. M20 grade Nominal Mix / Design Mix .

Steel Reinforcement: Providing and fabrication reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding ( including cost of binding wire) all complete up to floor five level. (Original producers who manufacture billet directly from iron ores and rolll the bilets to produce steel conforming to IS:1786) Thermo-mechanically Treated bars (Conforming of relevent IS code ) (100 kg per cum of c.c.)

Plaster on new surface on walls in cement sand mortar 1:4 including racking of joints complete fine finish : 20 mm thick

6 mm thick cement plaster to celling of mix 1:3 (1 cement : 3 fine sand )

Providing and applying white cement based putty over plastered surface to prepare the surface even and smooth complete. New plastered Surface (Three or more coats)

Distempering with dry distemper of approved brand and Shade ( two or more coats) and of required shade on new work, over and including, priming coat of whiting to give an even shade including all scaffolding.

Finishing wall with water proofing cement paint of approved brand and manufacture and or required shade to give an even shade including all scaffolding. New work (Two or more coats applied @3.84 kg / 10 sqm)

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade: Two or more coats on new work.

Supplying and fixing stone lintels/bed plates of approved quarry rough dressed in cement mortar 1:4 Upto 15 cm thick. Window / D

Providing dab stone over chajjas duly fixed in cement sand mortar 1:6 complete . 50mm thick

Providing and fixing horizontal chajja of Red/ white sand stone 40 mm thick and upto 80 cm projection in cement mortar 1:4 (1 cement : 4 coarse sand ) including pointing in white cement mortar 1:2 ( 1 white cement : 2 stone dust ) with an admixture of pigment matching the stone shade.

Filling available excavated earth (excluding rock) in trenches, plinth side of foundation etc. in layers not exceeding 20 cm. in depth, consolidating each deposited layer by ramming and watering including lead up to 50 meter and with all lift.

Random rubble dry stone kharanja under floor.

Providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering - all work up to plinth level. M15 grade Nominal mix 1:2:4 ( 1 cement : 2 course sand : 4 graded stone aggregate 40 mm nominal size ). (flooring)

Kota stone slab flooring 25 mm thick over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete with base of cement mortar 1:4(1 cement : 4 coarse sand ) for area of each slab from 901 to 2000 sq. Cm : 864.00

P & F European type white glazed vitreous china 1st quality Double syphonic W.C (IS :2556 Mark) with P or S trap including cutting and making good the wall and floor

P & F WVC Wash basin (Ist quality IS:2556 Mark) of approved make with C.I. brackets duly painted 1 No. 15 mm C.P. Pillar cock (IS:8934 Mark) & 32 mm C.P. brass waste- coupling of approved make, P.V.C Waste pipe with PVC nut 32 mm complete including cutting & making good the wall Size Size 580 mm x 450 mm

P & F Kitchen & Lab. Sink of approved make with C.I. brackets duly painted, 40 mm C.P. waste coupling, C.P. Brass chain with rubber plug, 40 mm G.I. waste pipe up-to floor level complete including cutting and making good the wall & floor : 22 x 18 x 7 20x16x7

P & F WVC (10 litres) low-level flushing cistern with cover

P & F Bevelled edge Mirror/mirror with teak wood lipping around of special glass of approved make as per direction of Engineer-in-charge complete with 6mm thick commercial ply base fixed to wooden screws & washers. Size 600 x 450mm x 4 mm thick

P & F Towel Rail or Ring of approved quality/make: C.P. brass Towel Rail elbow type with concealed screws size 450mm (Heavy duty).

C.P. Brass Towel Ring revolving type

P & F Soap Dish or Tray of approved quality/make C.P. brass heavy and superior quality.

P & F Bath Shower of approved quality/make C.P. brass of Heavy & superior quality 150mm.

P & F Jet spray for water closet with C.P. Copper Tube flange of approved make.

P & F G.I. pipes (Internal Work) with G.I. Fittings excluding union (IS:1239 Mark) & MS clamps including cutting and making good the walls and floors: (a) Exposed on wall 2.1.1 15 mm dia nominal bore 'B' Class

P & F Bib Cock (IS : 8931 Mark), Superior quality of approved make: Brass 400 gm,15mm nominal bore

P & F Full-way Valve (IS:778 Mark) or wheel valve of approved make : Gun-metal 15mm nominal bore.

P & F PVC Storage Tank ISI Marked (IS : 12701) indicating the BIS license No), of approved make with cover, 25mm dia 1M long G.I. over-flow pipe & 25 Cm. long wash out pipe with plug & socket, including making connection etc., complete of approved design: 500 ltr

P&F rigid PVC Pipe (IS:4985 mark) class II/ (4 Kg. /Cm2 .) approved quality /make including joining the pipe with solvent cement rubber ring and lubricant. 75 mm dia

P&F rigid PVC Pipe (IS:4985 mark) class II/ (4 Kg. /Cm2 .) approved quality /make including joining the pipe with solvent cement rubber ring and lubricant 160 mm dia

P&F rigid PVC pipe fittings (IS: 4985 mark) of approved quality /make including joining the pipe with solvent cement rubber ring and lubricant: Coupler (socket) 75 mm

P&F rigid PVC pipe fittings (IS: 4985 mark) of approved quality /make including joining the pipe with solvent cement rubber ring and lubricant: 75 mm

P&F rigid PVC pipe fittings (IS: 4985 mark) of approved quality /make including joining the pipe with solvent cementrubber ring and lubricant: Door Tee 110 mm

P & F rigid PVC pipe fittings (IS: 4985 mark) of approved quality /make including joining the pipe with solvent cement rubber ring and lubricant Bend 87 .5 (75 mm)

Vent Cower

P&F rigid PVC pipe fittings (IS: 4985 mark) of approved quality /make including joining the pipe with solvent cement rubber ring and lubricant: S trp 110 mm.

Construction of Soakage well in all types of soil of approved drawing, top 90 Cm .Portion in 450mm thick masonry with CM 1:6, 80 mm thick stone slab covering, jointing of slab in CM 1:3 ,Ralthal, kharanja 40mm thick M- 15 grade C.C flooring, earth work etc . complete includingdisposal of surplus earth within a lead of 50 mtr . Inner dia 90 Cm & 10 to 12 Mtr deep.

Earth work in excavation by mechanical means (hydraulic excavator) / manual means over areas (exceeding 30 cm in depth. 1.5m in width as well as 10 sum on plan) including disposal of excavated earth, lead upto 50m and all lift upto 1.5m disposed earth to be levelled and neatly dressed. All kind of soil.

Providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering all work up to plinth level. 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size.) Water Tank

Providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering all work up to plinth level. 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size.) Water Tank

Brick work with F.P.S. bricks of class designation 75 in superstructure above plinth level upto floor V level in all shapes and sizes in : Cement mortar 1:6 (1 cement : 6 coarse sand )

Plaster on new surface on walls in cement sand mortar 1:4 including racking of joints complete fine finish : 20 mm thick

Stone slab foofling on ground floor with fine grained stone slab from approved quarry including filling of joints of parapet and slab on both sides in cement sand mortar 1:4, with celling pointing in cement sand mortar 1:3 complete as per specification and instruction of Engineer in charge.

Suppling and Fixing stone lintels/bad plates of approved quarry rough dressed in cement mortar 1:4 Upto 15cm thick.

Supplying & Fixing RCC Manhoies covers with frame of Approved make (Light duty) Size 450x450mm

Wiring of light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV grade and 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade (IS:694) on surface ISI marked ( IS:14927 P - II ) virgin material UPVC trunking & it's accessories, Hot Dipped Galvanized Modular box of 1.2 mm thick with earth terminal/ Surface Moulded virgin material UPVC Modular Box , 10 A Modular switch,Modular face plate with grid plate, 3 pin ceiling rose/holder /3 way Connector, screws, making connections, testing etc. as required. For specification of copper Conductor, Phenolic Laminated sheet's & Electrical/ Wiring accessories refer Chapter E 04, E 05 & E 07 For additional technical parameters of product / work refer Annexure 'A' attached with this Medium point (up to 6 mtr.)

Long point (up to 10 mtr.)

Wiring of 3/5 pin 6 amp. Light plug point with 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV grade and 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade(IS:694) on surface ISI marked ( IS:14927 P - II ) virgin material UPVC Trunking & it's accessories, Hot Dipped Galvanized Modular box of 1.2 mm thick with earth terminal/ Surface Moulded virgin material UPVC Modular Box, modular 10A switch, 3/5 pin 6 A modular socket, Modular face plate with grid plate, screws, making connections, testing etc. as required. For specification of copper Conductor, Phenolic Laminated sheet's & Electrical/ Wiring accessories refer Chapter E - 04, E - 05 & E - 07 For additional technical parameters of product / work refer Annexure 'A' attached with this BSR On board

S&F following sizes of ISI marked ( IS:14927 P - II ) virgin material UPVC 25 mm x 12 mm trunking along with accessories like coupler, inner, outer, elbow, square box, tee, end cap etc. on surface with screws, expansion fasteners as required. For additional technical parameters of product / work refer Annexure'A attached with this 25 mm x 12 mm

Supplying and drawing FR PVC insulated & unsheathed flexible copper conductor as per PWD specification for electrical Works with ISI marked (IS:694) and as per IS 8130 : 2013 of 1.1 kV grade . Wire should be made from 99.90 % purity copper, class 5 stranding in acc. to IS:8130/IEC 60228 for lower watt loss , oxygen free for less chances of oxidization, insulation PVC type A/C/D , flame retardant as per IS 10810-53, better amperage rating as per IS:3961 part 5, in existing surface or recessed PVC/ MS conduit/casing capping making connections with Copper Lugs of suitable size, Ferrules,testing etc. as required. OEM Must have its own in house NABL lab setup for all testing facilities for wires. For additional technical parameters of product / work refer Annexure 'A' attached with this BSR 1 x 1.5 sq.mm

2 x 2.5 sq. mm. + 1x1.5sqmm

2 x 4.0 sq. mm. + 1 x 2.5 sq. mm.

Providing & Fixing of BEE Star rated copper wounded double ball bearing capacitor start, aluminium body & Meta

llic blade ceiling fan Conforming to all the performance requirements laid down in IS 374:2019 including all amendments, as applicable ; & Carry BIS licensing (i.e. ISI marking) with down rod up to 80 cm with secondary support safety cable ( steel rope) , cotter pin with 3 x 1.5 sq.mm pvc insulated flexible copper conductor making connection testing etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR .1200 mm Sweep BEE 1 Star rated service value >=4.0 to < 4.5 )

Providing & Fixing of IP20 SMD Mid Power LED batten type integrated light fixture made from Powder coated Extruded aluminium housing with in built driver , System lumen efficacy ≥ 110 lm/Watt output, internal surge protection of 2.5 KV with Short & Open circuit protection ,THD < 10% , P. F.≥0.95, CRI >80 , life time of minimum 50000 Burning Hours with , 70% of intial Lumen maintaned till life ends , CCT 3000°K / 4000°K / 5700°K /6000°K/6500°K (As per ANSI Bin) , Maximum power consumption should not more than the specified rating and Fixture shall be of BIS standard and trade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. OEM must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79 & LM80) certificate / Report from OEM shall be submitted. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR . 1170mm(+/-10%) LED batten with min. lumen output 2200 lm

Providing & Fixing of modular type 120 W Step Fan regulator duly ISI marked (IS 11037:1984 ) with CM/L no. printed made out of unbreakable and fire retardant vergin poly carbonate with brass terminals and captive screws & silver alloy contact tip with IP-20 rating , including all as per pre approved by Engineer in charge,making connections, testing etc. as required. For additional technical parameters of product / work refer Annexure 'A' attached with this BSR 5 step fan regulator 2 Module 360 dgree rotating

Supplying and fixing of power plug point with Modular accessories as per PWD specification for electrical Works, on hot dipped galvanized modular box of 1.2 mm thick with earthing terminal/connector on surface or in recessed with suitable size of modular face place with grid plate and cover plate including cost of ISI marked modular 16 amp. Switch (IS :3854) and 6/16 amp. socket outlet (IS:1293) making connection , testing , etc. as required. For specification of Wiring accessories refer Chapter E 07 related item & For additional technical parameters of product / work refer Annexure A attached with this BSR

Providing & Fixing of single / multi tone electronic call bell as per PWD specification for electrical Works, including making connection testing etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure A attached with this BSR .

Providing & Fixing of Recessed/surface mounting heavy duty horizontal type Double Door ( Metal / Glazed )Distribution board with Metal end box made out from Galvanized steel / CRCA sheet not less then 1.2 mm thick conforming to IS-8623-1 & 3 / IEC 61439- 1 & 3, powder painted complete with reversible door (for double door DB only )100 amp. insulated copper bus bar/shorting link , copper neutral link, copper earth link , color coded interconnecting wire set of suitable rating and din bar,masking sheet, making internal DB terminations with copper lugs, Ferrules, detachable gland plate, including making connections, testing etc. as required. OEM shall have submit NABL / CPRI / ERDA accrediated lab type test reports & All as per pre approved by Engineer in charge. For additional technical parameters of product / work refer Annexure 'A' attached with this BSR Metal door (single phase) IK-09 and IP-43 with Metal end box 12 Way (12+2)

40mm x 40mm x 1.5mm thick Factory made door frame of PVC extruded section in white, grey or woodwn finish

Block board construction flush door with teak wood ply on both faces 25 mm

Item No 2 - 2 Feet Height increase Top old Pakka Wall and Repair Of Old Pakka Wall 300 Rmt

Clearing jungle including uprooting of rank vegitation ,grass,brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removel of rubbish up to a distance of 50m outside the periphery of the area cleared

Earth work in excavation by mechanical means (hydraulic excabator ) manual means over areas ( exceeding 30 cm in deapth 1.5 m in width or 10 sqm on plan) icluding excavated earth, lead upto 50m and lift upto 1.50m disposal earth to be levelled and neatly dressed ,all kinds of soil

Random Rubble stone masonry for foundation and plinth in Cement Sand mortar above 30 cm thick wall in : Cement Mortar 1 : 6 (1-Cement : 6-Sand).

Block board construction flush door lipping

Brick work with F.P.S. bricks of class designation 75 in superstructure above plinth level upto floor V level in all shapes and sizes in : Cement mortar 1:6 (1 cement : 6 coarse sand )

Plaster on new surface on stone masonary in cement sand mortar 1:3 including racking of joints etc. complete fine finish 25 mm thick

Providing and laying damp proof course with cement concrete Grade M-150(1:2:4) Mortar prepared with 1 % soluition of water proof compound complete as per specification 75 mm thick

Item No 3 Construction Work Of New Building

Clearing jungle including uprooting of rank vegitation ,grass,brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removel of rubbish up to a distance of 50m outside the periphery of the area cleared

Earth work in excavation by mechanical means (hydraulic excabator ) manual means over areas ( exceeding 30 cm in deapth 1.5 m in width or 10 sqm on plan) icluding excavated earth, lead upto 50m and lift upto 1.50m disposal earth to be levelled and neatly dressed ,all kinds of soil

Random Rubble stone masonry for foundation and plinth in Cement Sand mortar above 30 cm thick wall in : Cement Mortar 1 : 6 (1-Cement : 6-Sand).

Random Rubble stone masonry for superstructure above plinth level one storey height above 30 cm. thick walls in : Cement Mortar 1 : 6 (1-Cement : 6-Sand).

Plaster on new surface on stone masonary in cement sand mortar 1:3 including racking of joints etc. complete fine finish 25 mm thick

Providing and laying damp proof course with cement concrete Grade M-150(1:2:4) Mortar prepared with 1 % soluition of water proof compound complete as per specification 50 mm thick

Item No 4 Construction of Vermi compost Unit (20 Beds)

Earth work in excavation by mechanical means (Hydraulic excavator ) manual over areas (exceeding 30 cm in depth, 1.5m in width as well as 10 sqm on plan ) including disposal of excavated earth, lead upto 50m and lift upto 1.5 m disposed earth to be levelled and neatly dressed. All kinds of soil

Providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering - All work up to plinth level. 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size.)

Random Rubble stone masonry for with hard stone in foundation and plinth in Cement Sand mortar above 30 CM thick wall in: Cement Mortar 1:6 ( 1-Cement : 6-Sand).

Brick work with F.P.S. bricks of class designation 75 in superstructure above plinth level upto floor V level in all shapes and sizes in : Cement mortar 1:6 (1 cement : 6 coarse sand )

Centering & Shuttering with plywood or steel sheets including strutting, propping bracing both ways with steel props and removal of formwork for upto floor five level for : Suspended floors, roofs, landings, staircases, balconies, girders, cantilevers, bands, coping bed plates, anchor blocks, sills, chhajjas, lintel, beam, plinth beam etc.

Teen Shed kary

Steel Reinforcement: Providing and fabrication reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding ( including cost of binding wire) all complete up to floor five level. (Original producers who manufacture billet directly from iron ores and rolll the bilets to produce steel conforming to IS:1786) Thermo-mechanically Treated bars (Conforming of relevent IS code ) (100 kg per cum of c.c.)

Plaster on new surface on walls in cement sand mortar 1:4 including racking of joints complete fine finish : 20 mm thick

Supplying and fixing stone lintels/bed plates of approved quarry rough dressed in cement mortar 1:4 Upto 15 cm thick. Window / D

Providing and fixing horizontal chajja of Red/ white sand stone 40 mm thick and upto 80 cm projection in cement mortar 1:4 (1 cement : 4 coarse sand ) including pointing in white cement mortar 1:2 ( 1 white cement : 2 stone dust ) with an admixture of pigment matching the stone shade.

Filling available excavated earth (excluding rock) in trenches, plinth side of foundation etc. in layers not exceeding 20 cm. in depth, consolidating each deposited layer by ramming and watering including lead up to 50 meter and with all lift.

Providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering - all work up to plinth level. M15 grade Nominal mix 1:2:4 ( 1 cement : 2 course sand : 4 graded stone aggregate 40 mm nominal size ). (flooring)

Providing and laying in position specified grade of cement concretee for RCC structural elements upto floor five level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers (if required ) excluding the cost of centering, shuttering and reinforcement for Walls (any thickness) including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. M20 grade Nominal Mix / Design Mix .

Item No 5 Construction of Pakka Beds (20 Beds)

Clearing jungle including uprooting of rank vegitation ,grass,brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removel of rubbish up to a distance of 50m outside the periphery of the area cleared

Earth work in excavation by mechanical means (hydraulic excabator ) manual means over areas ( exceeding 30 cm in deapth 1.5 m in width or 10 sqm on plan) icluding excavated earth, lead upto 50m and lift upto 1.50m disposal earth to be levelled and neatly dressed ,all kinds of soil

Random Rubble stone masonry for foundation and plinth in Cement Sand mortar above 30 cm thick wall in : Cement Mortar 1 : 6 (1-Cement : 6-Sand).

Random Rubble stone masonry for superstructure above plinth level one storey height above 30 cm. thick walls in : Cement Mortar 1 : 6 (1-Cement : 6-Sand).

Plaster on new surface on stone masonary in cement sand mortar 1:3 including racking of joints etc. complete fine finish 25 mm thick

Providing and laying damp proof course with cement concrete Grade M-150(1:2:4) Mortar prepared with 1 % soluition of water proof compound complete as per specification 50 mm thick

Gate and Window fitting