House Keeping Maintenance and Operation work at Erector Hostel at 220 KV Ss Natwa Mirzapur F Y 2026 27 2027 28)

Providing catering services in erector hostels/Guest houses/ Inspection houses for upto 4 suites including maininance and cleaning of cutlery, crockery and also including provision of morning/evening tea and meals on payment basis to the guests/ occupants. (CSI No. 23.01a)

House Keeping of all suits, dormitary, dining hall, kitchen & outer area that include lobby, stairs, road, parking including cleaning/sweeping/dusting and praparation of bed with clean and ironed bed sheet /cover/pillows/blanket etc. Proper cleaning of bathroom, providing with soap, bath soap, shampoo pouch, odonil, sanitry cubes, cleaning big and small towel, Mosquito repellant as and when required its also add removal of rubbish from permises. Rates include all labour, material, T & P required for proper completion of work. (For One Month per sqm of carpet area) For all other districts in UP except that mentioned in item number 23.17. (CSI No 23.18)

Supplying and stacking of good earth at site including royalty and carriage upto 5 km lead complete (earth measured in stacks will be reduced by 20% for payment).(DSR Horticulture 2020 2.2) Chapter-28.02

Spreading of sludge, dump manure and/or good earth in required thickness as per direction of officer-in-charge (cost of sludge, dump manure and/ or good earth to be paid separately).(DSR Horticulture 2020 2.8)Chapter-28.04

Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared (DSR No.-2.31)

Clearing grass and removal of the rubbish up to a distance of 50 m outside the periphery of the area cleared.(DSR-2.32)

1:1½:3 (1 Cement: 1½ coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)(DSR NO.-4.1.2)

Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq.meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in-Charge.With cement mortar 1:4 (1cement: 4 coarse sand)(DSR-14.1.2)

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.(DSR No.-13.80)

Finishing walls with Acrylic Smooth exterior paint of required shade :new work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm)(DSR No. 13.46.1)

Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gram/litre, of approved manufacturer and of required shade and colour all complete to achieve even shade and colour :New work (two or more coats) over and including water thinnable priming coat with cement primer having VOC content less than 50 gram/litre(DSR No.13.41.1)

Providing and stacking of Polyalthia pendula (Ashok Pendula) of height 180-195 cm. in gunny bag of size 30 cm as per direction of the officer-in-charge.(DSR Horticulture 2020 7.77) Chaptere-28.06

Providing and stacking of Bottle palm of ht. 150-180 cm bottom girth 20-25cm well developed in big poly bags of size 25 cm as per direction of the officer-in-charge.(DSR Horticulture 2020 7.10) Chaptere-28.07

Providing and stacking of Mangifera indica (Mango-grafted ) of height 60-75 cm. in big poly bag of size 25 cm as per direction of the officer-in-charge.(DSR Horticulture 2020 7.53)Chaptere-28.08

Providing and stacking of Azadirachta indica ( Neem ) of height 120-130cm in big polybag of size 25 cm as per direction of the officer-in-charge.(DSR Horticulture 2020 7.5)Chaptere-28.09

Cleaning of septic tank including disposal of waste out side the UPPCL area as per direction of the Engineer-in-charge including cost of all labour,T&P etc.required for proper completion of the work.(CSI No. 20.12)

Same as in item No.20.12 above but for inspection chamber..(CSI No. 20.13)

Cleaning and opening of chocked W.C./ bath / kithchen pipe line including opening and refixing.(CSI No. 20.19)

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 3 pin 5/6 amp socket outlet (DSR E&M 2022 1.24.4)Chapter-27.02

Supplying and fixing following size/ modules, GI box along with modular base & cover plate for modular switches in recess etc as required. 4 Module (125mmX75mm)(DSR E&M 2022 1.27.3)DSR-27.18

Supplying and fixing of 20 mm of medium class PVC conduit along with accessories in surface/recess including junction box, cutting the wall and making good the same in case of recessed conduit as required. (DSR E&M 2022 1.21.1)Chapter-27.03

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required..Group C (DSR E&M 2022 1.10.3)Chapter-27.01

Rewinding of burnt ceiling fan with approved copper wire including cost of all materials, labour and T&P etc. complete (Burnt wire will not be taken back.) CSI-22.08

Supply and replacing of burnt and damaged condenser of ceiling fan of approved quality including all materials,labour and T&P etc. CSI-22.09

Taking off the defective ceiling fan from position & re hanging after receiving the repaired fan and proper connection etc.CSI-22.10

Greasing of ceiling fan after cleaning the bearing and shaft with oil / petrol and its testing.CSI-22.11

Removal of old and damaged sunfilm from the glass panes of door and window shutters,including removal of Glue completely and carefully by scraping or by any means including cost of all materials, labour T&P etc. required for proper completion of the work.CSI-22.13

Providing and fixing sun-film of Gareware or equivalent make on glass panes of door and window shutters including cost of all materials,labour and T&P etc. required for proper completion of the work.CSI-22.14

Attending to petty maintenance service like plumbing service,welder service, mansion service and carpenter service required as below. (Job attending by one no. Plumber/welder/mason /carpenter with one no. helper per hour or part of an hour.) CSI-22.18

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc.15 mm dia nominal bore DSR-18.10.1

20 mm dia nominal bore DSR-18.10.2

25 mm dia nominal bore DSR-18.10.3

32 mm dia nominal bore DSR-18.10.4

making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete :25 to 40 mm nominal bore DSR NO.-18.13.1

Providing and fixing gun metal non- return valve of approved quality (screwed end) DSR-18.19.1.1

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete :DSR NO.18.18.1

Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved.(DSR-15.60)

Cleaning panes of glass with spirit of caustic soda including supply of all materials,labour and T&P etc. required for proper completion of the work. (CSI No. 20.09)

Cleaning and sweeping of roof of residence as and when required including uprooting of rank vegetation and disposal of the garbage upto 50 M.(CSI-22.20)

Cleaning of roads and their side patteries including sweeping,removing garbage and vegetation from patteries, if any and and its disposal to dust bins.(CSI-22.21)

Providing and displaying of Areca Palm having ht. 90 cm to 1.20 m with 4 to 5 suckers, well developed, fresh and healthy with lush green foliage in 25 cm size of Earthen pot/Plastic pot & as per direction of the officer-in-charge.(DSR Horticulture 2020 3.18) chapter-28.16

Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete.10 litre capacity - White(DSR-17.18.1)

Providing and fixing G.I. inlet connection for flush pipe connecting with W.C. pan.(DSR-17.22)

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.Flexible pipe 32 mm dia (DSR-17.28.2.1)

Supply and fixing of LED Tube Light batten fitting suitable for up to 1 X 22 watt LED tube light on surface complete in all respect.(CSI No. 28.41)

Cleaning of toilets of non-residential buildings including cost of detergent powder,horpic phenyl and suitable acid etc. as required for proper completion of the work.(CSI-22.22)

Servicing of Air Conditioner (For Window/Split) by aurthorised service center complete in all respect including all labour and T&P. (CSI No. 20.30)

Servicing of Air Conditioner and filling of GAS (For Window/Split) by aurthorised service center complete in all respect including all labour and T&P. (CSI No. 20.31)

Cleaning of main drain or width more than 300 mm.including disposal of waste refuses sludge out side the board's area including washing and cleaning by clean water completely as per direction of the Engineer-in-charge including cost of all labour,T&P etc.required for proper completion of the work.(CSI No. 20.14)

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and for all lift, as directed by Engineer-in-charge.(DSR 2.6.1)

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete.(DSR 2.27)

Providing and laying 1:5:10 (1 cement : 5 coarse sand (zone-III) derived from natural sources : 10 graded stone aggregate 40 mm nominal size derived from natural sources) in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :(DSR 4.1.10))

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:4 (1 cement : 4 coarse sand) (DSR No. 6.1.1)

Providing and laying 80 mm thick C.C. paver block of M-35 grade with approved colour design and pattern. factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge.(DSR 16.91.2)

12 mm cement plaster1:4 (1 cement: 4 coarse sand) of mix :(DSR 13.4.1)

Providing and laying Double charge vitrified tile polished finish of size of Tile 600 x 600 mm floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.:(DSR 11.41A.1.1)

Providing and laying Glazed Vitrified tiles Matt/Antiskid finish of size of Tile 600 x 600 mm floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.:(DSR 11.41A.3.1)

Demolishing cement concrete Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge(DSR 15.2.1)

Supply and Fixing of 5 blade Exhaust fan ventile air dx 225 mm of Havells or equivalent make including all material, T&P etc required for proper completion of work as approved by engineer in charge.(CSI No. 28.38)

Supply and fixing of 36 Watt to 46 Watt indoor Recess mounting LED Square Fitting for Armstrong Ceiling having Powder coated die cast aluminium housing body with extended heat sink and diffuser of Special Polycarbonate meterial and driver set complete in all respect. (CSI No. 28.40)

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277. (DSR No 12.45.2)

Providing and fixing CP Brass Single lever telephonic wall mixer of quality & make as approved by Engineer in charge.(a) 15 mm nominal dia (DSR-17.22B)

Providing and fixing one piece construction white vitreous china squatting plate with an integral longitudinal flushing pipe, white P.V.C. automatic flushing cistern, with fittings, standard size G.I. / PVC flush pipe for back and front flush with standard spreader pipes with fittings, G.I clamps and C.P. brass coupling complete, including painting of fittings and cutting and making good the walls and floors etc. wherever required :Range of three squatting plates with 10 litre P.V.C. automatic flushing cistern(DSR 17.6.3)

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. (DSR - 17.31)

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.15 mm nominal dia Pipes(DSR-18.7.1)

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 :15 mm nominal bore (DSR - 18.49.1)

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 ,15mm nominal bore (DSR-18.53.1)

S/F of Jaquar make Towel Rail of model No. AQN 7711A 450 mm long as per direction of engineer in charge. This include cost of labour, material T&P etc for proper completion of work. (CSI No. 26.36)

PROVIDING AND FIXING SOAP DISH CHROMIUM PLATED WITH BRACKETS FIXED TO WOODEN CLEATS WITH B RASS SCREWS INCLUDING SUPPLY OF ALL MATERIALS,LABOUR AND T&P ETC.REQUIRED FOR PROPER COMPL ETION OF THE WORK. (NSI NO. 27.19)

Wiring for circuit/submain wiring with 2x2.5Sq.mm+1x2.5Sq.mm earth wire of FRLS PVC insulated copper conductor, single core cable in surface/recessed medium class PVC conduit as required. (DSR E&M 2022 1.14.2) (DSR-27.05

Please Enable Macros to View BoQ information

Special Condition :-

General"."

General"."

General"."

General"."

General"."

General"."

General"."

General"."

General"."

General"."

General"."

General"."

General"."

General"."

General"."

General"."

General"."

General"."

General"."

General"."

General"."

General"."

General"."

General"."

General"."

General"."

General"."

General"."

SIGNATURE OF TENDERER / AUTHORISED

PERSON ALONGWITH SEAL OF THE FIRM

Full Postal Address:……………………….

Phone No……………….. Mob. No…………