ADDITION ALTERATION OF MBT GUN SHED AT ARDE PASHAN

Amount

Demolition of Brick work or stone / boulder masonry, built in cement mortar including all quoins, arches, pillars, etc but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed.

Demolition of reinforced cement concrete slab complete all as specified and directed.

Taking down cement plaster or cement lime plaster of any description on brick or stone walls etc including racking out joints for key, scrubing down with water etc complete all as specified and directed.

Taking down chowkhat exc 1.5 sqm and n exc 4.00 sqm each without taking of shutter from frame complete all as specified and directed.

Taking down chowkhat n exc 1.5 sqm each without taking of shutter from frame complete all as sepecified and directed.

Dismantling of asbestos cement (corrugated, semi corrugated etc.) sheets in roof coverings complete all as specfied and directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings n. exc 15cm thickness (below or above GL) complete all as specified and directed.

Material and labour for pre-cast cement concrete block masonry 1:3:6 type C1 (using 20mm graded crushed stone aggregate) with solid blocks exc. 10cm in width and setting in cement mortar 1:6 complete all as specified and directed.

Material and labour for pre-cast cement concrete block masonry 1:3:6 type C1 (using 20mm graded crushed stone aggregate) with solid blocks n. exc. 10cm in width and setting in cement mortar 1:4 complete all as specified and directed.

Material and labour for reinforced cement concrete slabs supported on walls type B-1 (1:2:4) (using 20mm graded crushed stone aggregate) complete all as specified and directed.

Material and labour for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work, not exceeding 200 mm thick (horizontal or sloping) complete all as specified and directed.

Supply and fix solid PVC door frame of size 50mm x 47mm made out of 5mm thick plain colour PVC sheet reinforced with MS square tube Supply and fix in opening as per specification & drawings complete all as specified and directed.

Supply and fix Factory made solid panel PVC door shutter 30 mm thick (stile) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing. complete all as specified and directed

Supply and fix 105 mm X 60 mm size of Pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc, complete all as specified and as directed.

Material and labour for plain cement concrete 1:3:6 Type C2, ( using 20 mm graded crushed stone aggregate) for filling of hollow pressed steel frame complete all as specified and directed.

Material and labour for plain cement concrete 1:2:4 Type B-0 ( using 12.5 mm graded crushed stone aggregates) for fixing hold fast including repairing of disturbed plaster ( while taking down Door/window,ventilator frame) and matching the repaired surface with existing one complete all as specified and directed.

Supply and fix 35mm thick factory made flush shutters, solid, core construction with black board core and plywood face panals commercial type on both sides complete all as specified and directed.

Supply and fix extruded Aluminium alloy handles, fabricated type anodised size 100 mm complete all as specified and directed.

Supply and fix 150 mm long extruded aluminium alloy handles, fabricated type, anodised and fixed complete all as specified and directed.

Supply and fix 100 mm long aluminium anodised barrel tower bolt of extruded section complete all as specified and directed.

Supply and fix 150 mm long aluminum anodized barred tower bolts of extruded section complete all as specified and directed.

Supply and fix aluminium alloy anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet cast or extruded sections and fixing bolt and sliding bolt of extruded sections or cast aluminium alloy length of bolt 300mm long complete all as specified and directed.

Supply and fix aluminium alloy anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet cast or extruded sections and fixing bolt and sliding bolt of extruded sections or cast aluminium alloy length of bolt 200mm long complete all as specified and directed.

Supply and fix 100mm butt hinges extruded aluminum alloy with galvanised mild steel hinge pin anodised type B-21 complete all as specified and directed.

Material and labour for mild steel TMT bars 8mm dia and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

Disconnecting existing PVC tanks and removing to store of capacity exc 500 litre and n. exc. 1000 litre complete all as specified and directed.

Supply and fix rotational moulded polytheylene water storage tanks (cylindrical vertical with closed top) hoised and fixed in position all as specified in SSR Part I of capacity 1000 litre complete all as specified and directed.

Taking up or down steel tubing 20mm dia and connections including cleaning for refixing complete all as specified and directed.

Taking up or down steel tubing 15 mm dia and connections including cleaning for refixing complete all as specified and directed.

Supply and fix tubes medium grade 20mm bore galvanised with all fittings fixed to walls / concealed pipe work or laid in floors complete all as specified and directed.

Supply and fix tubes medium grade 15 mm bore galvanised with all fittings fixed to walls / concealed pipe work or laid in floors complete all as specified and directed.

Supply and fix 50 mm bore unplasticised PVC pipes of pressure rating 10 Kgf/cm2 fixed to walls, ceiling or in floors complete all as specified and directed.

Supply and fix ball brass valve high pressure with polythene float and flynut complete screwed for iron pipe or brass ferrule and fixed of size 20mm bore complete all as specified and directed.

Supply and fix in repair PVC connection 15mm size with PTMT nuts of length 375 mm complete all as specified and directed.

Supply and fix gun metal globe or gate valve 20mm bore with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

Dismantling and breaking up drain pipes AC /CI /PVC set in cement mortar 110mm/75mm bore complete all as specified and directed.

Supply and fix 110mm bore UPVC (SWR) pipes single socketed in any length with rubber ring joint fixed to wall complete all as specified and directed.

Supply and fix UPVC (SWR) bends any radius 110mm bore complete all as specified and directed.

Supply and fix UPVC (SWR) vent cowl any radius 110mm bore complete all as specified and directed.

Supply and fix 75mm UPVC (SWR) multi floor trap with grating including jointing with solvent cement complete all as specified and directed.

Supply and fix in repair long neck pillar cock 15mm dia CP fancy type long screwd shank complete all as specified and directed.

Supply and fix in repairs 15mm bore fancy type chromium plated bib taps with crutch or butterfly handle screwed down for iron pipes complete all as specified and directed.

Supply and fix in repair angle stop cock chromium plated screwed for iron pipe or brass ferrule, 15 mm bore and fixed complete all as specified and directed.

Supply and fix in repair towel rail 600 mm long brass Chromium plated 20 mm dia fixed to wall etc complete all as specified and directed.

Supply and fix urinal spreader for fixing with 15mm dia pipe complete all as specified and directed.

Supply and fix Push cock, CP Fancy type 15mm bore complete all as specified and directed.

Supply and fix in repair Wash hand basin, Vitreous China oval shaped, first quality, white colour, of size 550mm x 400mm x 175mm, including cutting for and pinning in ends of brackets or erecting stand, with and including CI brackets, PVC flexible pipe with both side brass nuts to joint and 750mm long PVC waste pipe 32mm dia, CP waste coupling with long screwed shanks and fly nuts, complete all as specified and directed.

Supply and fix in repair vitreous china squatting pan, 'Orissa' pattern, size 580mm x 440mm white, with integral foot rests (excluding flushing cistern and flush pipe) complete all as specified and directed.

Supply and fix PVC valveless, syphonic action type, flushing cistern, low level white with inlet, ball valve, float and handle including brackets capacity of 10 litre complete all as specified and directed.

Supply and fix in repair vitreous china urinal, half stall type, white (excluding flushing cistern, flush pipe and waste pipe) complete all as specified and directed.

Material and labour for rendering 10mm thick in cement mortar 1:6 on internal surfaces of brick work or concrete surfaces finished even and smooth without using extra cement at any height including necessary scaffolding complete all as specified and directed.

Material and labour for rendering 15mm thick in two layers on fair faces of brick work or concrete surfaces 10mm thick in cement mortat 1:6 and top layer 5mm thick in cement mortar 1:4 mixed with integral water proofing compound finished even and smooth (without using extra cement) (WPC Shall be measured and paid separately) at any height including necessary scaffolding complete all as specified and directed.

Material and labour for 5mm thick plastering in cement mortar 1:3 on ceiling and finished even and smooth without using extra cement at any height including necessary scaffolding complete all as specified and directed.

Material and labour for preparation of newly plastered surfaces of wall and applying one coat of chalk whitening preparatory to distempering to plastered surfaces and applying two coats of oil emulsion distemper at any height including necessary scaffolding complete all as specified and directed.

Material and labour for preparing newly plastered surfaces of wall applying two coat of exterior emulsion weather coat over and including a coat of acrylic primer after preparing surfaces of any height including sacffolding etc complete all as specified and directed.

Material and labour for preparation of new plastered surfaces of ceiling and applying three coats of white wash on ceiling at any height including necessary scaffolding complete all as specified and directed.

Factory made box type steel windows, shop coated, glazing with sheet glass including cutting holes 04 Nos for each window for hold fasts, 150x230x75mm, PCC(1:2:4) type B1(using 20mm graded crushed stone aggregate) for fixing hold fasts including necessary form work, including pressed steel frame duly filled with PCC (1:3:6) type B1 (using 20 mm graded crushed stone aggregate) complete all as shown in drawing No. CERD/TD-485 / 2021, sheet Nos. 1/5 to 5/5 complete all as directed. Notes : (i) Glass panes & painting shall be measured and paid separately under respective items of BOQ (ii) Hold fasts 150mm long made out of 25x6mm flat iron made to shape-04 Nos per Window.(Each side-02 Nos)

Factory made box type steel ventilators, primer coated, glazing with wired glass, including pressed steel frame duly filled with PCC (1:3:6) type B1 (using 20 mm graded crushed stone aggregate) complete all as shown in drawing No. CERD/TD-485 / 2021, Sheet No.1/5 to 5/5 complete all as directed. Notes : (i) Glass panes & painting shall be measured and paid separately under respective items (ii) Hold fasts 150mm long made out of 25x6mm flat iron made to shape-04 Nos per Ventilator.(Each side-02 Nos)

Supply and fix aluminium sliding windows three track with and including two glass shutters using and including 4mm thick tinted glass (Modi Guard) and one shutter with and including stainless steel wire gauge wire cloth of 0.31mm nominal dia and width of aperture 1.61mm using powder coated aluminium sections including necessary joining cleats, glazing clips, rubber packing PVC track, handle lock, anodised aluminium snap beading, screws etc complete all as specified and directed. (i) Three track top & vertical - Jindal main 2010 Section No. 20621 (ii) Three track bottom - Jindal main 2010 Section No. 20620 (iii) Shutter Top and bottom - Jindal main 2010 Section No. 20604 (iv) Shutter vertical middle (interlock) - Jindal main 2010 Section No. 20605.

Supply and fix Aluminium powder coated ventilators partly fix and partly lowered of aluminium section designed DG-2762 (40 mm x 32 mm x1.5 mm thick) (weight 0.668 kg/metre) frame and DG-2763 and middle section of designed DG-2763 (40 mm x 32 mm x 1.5 mm thick) (weight 0.654 kg/metre), middle section DG-2546 (17.27 mm x 17.15 mm x 1.22 mm thick) (weight 0.124 kg/metre) including 5 mm thick pinheaded figured glass louvers with blades of 100 mm heavy duty including with aluminium lever handle fixed panel shall be provided with and including 5 mm thick pin headed figured glass including all necessary rubber packing, anodized aluminium snap beading fixed with minimum 6 Nos of suitable size galvanised screws with PVC plug etc complete all as specified and directed.

Supply and fix Framed work such as MS grill framed guard bar etc confirming to Fe-410-0 or Fe-310-0 including all necessary welding etc complete all as specified and directed.

Supply and fix pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as specified and directed.

Supply and fix pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screwscomplete all as specified and directed.

Material and labour for PCC M-25 Design Mix in hard standing/pavement using 20mm graded crushed stone aggregate, thickness of concrete 25cm or less and finishing the surface even and fair including necessary formwork complete all as specified and directed.

Material and labour for PCC M-25 Design Mix in hard standing/ pavement using 20mm graded crushed stone aggregate, thickness of concrete 25cm or less and finishing the surface even and smooth without using extra cement including necessary formwork complete all as specified and directed.

Material and labour for finishing cement concrete surface by making spike rolling to surfaces or making impressions of expanded metal, while the concrete is green complete all as sepecified and directed.

Material and labour for 75 mm thick PCC 1:3:6 type C2 (using 40mm graded crushed stone aggregate in plinth protection finished even and smooth without using extra cement complete all as specified and directed.

Material and labour for Hard core of gauge n exc 63 mm of broken boulder bellow plinth protection/hard standing complete all as specified and directed.

Material and labour for forming 12mm thick Expansion joints filled with and including pre-formed bituminous filler and top 30mm primed and sealed with sealing compound, Grade ‘A’ thickness of slab 150mm complete all as specified and directed.

Material and labour for forming Contraction (Dummy) joints 65mm deep x 10mm wide, filled with and including sealing compound Grade 'A' complete all as specified and directed.

Material and labour for forming Construction joint 30mm deep x 10mm wide filled withand including sealing compound Grade 'A' complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

Supply and fix steel rolling shutters, 1.25mm thick lath with out ball bearing as specified including top cover, anchoring rod, hasp and stapple and one shop coat of primer erected in position as indicated, complete but gear operated type with chain complete all as specified and directed.

Supply and fix safety lever locks mild steel with 4 levers for rolling shutters complete all as specified and directed.

Dismantling floor, hearth or wall tilling including cement mortar bedding ( but not backing) and rubbish off the premises complete all as specified and directed.

Material and labour for Non-skid coloured ceramic tiles 7mm to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

All as per Item No. 77 above but on vertical surfaces including 10mm thick backing coat in cement mortar 1:4 complete all as specified and directed.

Material and labour for glazed coloured ceramic tiles in vertical surface 450mm x 300mm x 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match including 10mm thick backing coat in cement mortar 1:4 complete all as specified and directed.

Supply and fix door closer hydraulically regulated designations No 3 universal type suitable for door shutters of 851mm to 1000 mm in width and weight between 61 kg to 80 Kgs and fixed of aluminium (extruded section body) complete all as specified and directed.

Material and labour for roof trusses (framed), trussed, purlins, cranegantries, rails and fastenings and heavy bracket framing (beam, tee, angle, square/rectangular tube, channel of flat sections) including distance pices, cleats etc of (Fe 290Gde E-165) Quality A complete all as specified and directed.

Material and labour for preparation of new steel surfaces of any description over 10 cm in width or girth and applying two coats of synthetic enamel paint over and including a coat of pink primer complete all as specified and directed.

Material and labour for removing old paint by paint removers or burning up by blow lamps and cleaning with scrapes any no of coats over 10cm in width or girth and applying two coats of synthetic enamel paint over and including a coat of Red oxide zinc chrome primer complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in roof/floors other than ground level beam, stair case, landing, chajjas and similar items including water proofing treatment in any layers and removal of debris to distance exceeding 250 metre and not exceeding 500 metre from the site complete all as specified and directed.

Material and labour for fillet of 75mm size using PCC 1:2:4 type B-0 (using 12.50 mm graded crushed stone aggregate at the junction of all horizontal and vertical surfaces complete all as specified and directed.

Material and labour for PCC 1:2:4 (Type B0 using 12.5 mm graded crushed stone aggregate) (40mm thick avg) as in levelling course to match the undulations of roof and in coving, roof kerbs including benching etc including necessary formwork and finished rough surface complete all as specified and directed.

Material and labour for rendering 10 mm thick on fair faces of concrete surface in cement mortar 1:3 to receive the roof finishes with water proofing compound. (WPC Shall be measured and paid separately) complete all as specified and directed.

Supply and fix 3mm thick APP pre-fabricated membrane with and including non woven polyester matt central core of 160 gsm (min) impregnated and coated on both sides with and including layer of APP modified bitumen and finished with and including micro-perforated heat fusible polythene film on both surfaces over and including 0.3 litres / Sqm bituminous primer confrming to IS-3384 and applying a coat of hot blown bitumen 85/25 grade @1.2 Kg/Sqm over the membrane and finally applying two coats of aluminium paint @ 0.10 litres / Sqm each layer complete as per manufacturer's instructions and all as specified and directed . The weight of APP membrane shall not be less than 3.0 Kg / Sqm and laid over and including primed surface by using LPG/Butane torch and apply uniform pressure with roller. The overlap of membrane shall be 100 mm on sides and 150mm on end laps and complete all as specified and directed. Notes: (i) The work shall be executed only through authorised applicator of manufacturer as approval by GE. (ii) Contractor has to submit guarantee of treatment for 10 Years. (iii) Rates are inclusive of cleaning the surface by roughening, sweeping clean and washing down and applying cement slurry @ 3 kgs/sqm Complete all as specified and directed. Make :- Super Thermolay APP PL of STP Ltd, Hyperlas of M/s IWL India Ltd, Hydrostop of M/s Tiki Tar Dansoa (India) Ltd, Torchat of M/s Torchtar membranes & bitumen products Pvt Ltd, M/s Fosroc Chemicals, Asian Paints Smartcare APP membranes of M/s Asian Paints Ltd.

Supply only water proofing compound complete all as specified and directed.

Supply and fix sheet glass 4.0mm thick ordinary quality exc. 0.5 sqm in each pane complete all as specified and directed.

Material and labour for 18mm to 20 mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, windows cills, cooking platforms and like set in cement mortar 1:4 including pointing in white cement (1:2) using marble dust with admixture of pigment to match the shade of granite including provision of 15 mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

Rounding to stone / granite slabs one edge, such as in steps, cooking platform and other similar situations complete all as specified and directed.

Material and labour for complete removal of existing treatment on wall and applying two coat of exterior emulsion over and including a coat of acrylic primer after preparation of surfaces of any height including necessary scaffolding etc complete all as specified and directed.

Material and labour for complete removal of existing treatment on wall and applying one coat of chalk whitening to plastered surfaces preparatory to distempering and applying two coats of oil emulsion distemper including at any height including necessary scaffolding all as specified complete all as specified and directed.

Cleaning of shrubs growth on bldgs and making good damaged portion in cement mortar 1:3 and match the existing surfaces of any height complete all as specified and directed.

Material and labour for anti-termite treatment along the external wall below concrete or masonary apron using chemical emulsion @ 2.25 litre per linear metre including drilling and plugging holes etc in apron complete all as specified and directed.

Material and labour for anti-termite treatment of soil under existing floors using emulsion @ one litre per hole, 300 mm apart including drilling and plugging 12 mm dia holes with cement mortar 1:2 (1 cement : 2 coarse sand) to match the existing floors complete all as specified and directed.

Material and labour for providing and injecting chemical emulsion for Post Constructional Antitermite Treatment along external wall where the apron is not provided using chemical emulsion at the rate of 7.5 litres per sq.m of the vertical surface of the sub-structure to a depth of 300mm including excavating channel along the wall and rodding etc. complete all as specified and directed.

Supply and fix erection and fixing only MS framed work as in gate gde Fe-290 or E-165 and or other section with gusset plate, railing braces etc complete, drilled for fixing of steel sheeting or other coverings, gates to be prepared for hanging or sliding with and including either hooks and hinges or steel hangings door fittings and hanging also fastening and including pintol hinges, stops, hand made sliding bolts etc complete. Design, size of componets and elevation of gates shall be all as directed by Engr-in-charge complete all as specified and directed.

Scrapping loosened/cracked concrete of RCC structure by chiselling etc including removal of debris away from site complete all as specified and directed.

Material and labour for applying pressure guniting 40mm thick to all affected area of RCC/masonary structure including necessary scaffolding for the height of up to 6.00 metre from ground level including and using sprayset HBL of Fosroc or equivalent of Pidilite @ 5 ml per 100 kg of cement and coarse sand in the ratio of 1:3 as per manufacturer instruction complete all as specified and directed.

Supply and fix welded steel wire fabric n exc 4 Kg/Sqm fixed with necessary nails/fasteners and mild steel wire not less than 0.9 mm dia etc at wall/floor/slab etc complete all as specified and directed.

Excavation in trenches n. exc. 1.50 metre deep & n. exc. 1.5 metre wide for foundation etc and getting out in soft/disintegrated rock complete all as specified and directed.

Demolition and breaking up drain pipes (salt glazed ware, AC or reinforced concrete pipes) set in cement mortar complete all as specified and directed.

Material and labour for 150mm dia reinforced cement concrete pipe CL NP-2 laid and joionted complete with collars complete all as specified and directed.

Material and labour for concrete bed to drain pipes 150mm dia including packing under and completely surrounding against the side of pipes after they are laid and tested in PCC 1:3:6 type C2 using 40mm graded crushed stone aggregate complete all as specified and directed.

Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channael concrete 1:2:4 type B1 using 20 mm graded crushed stone aggregate smooth finished and reforming benching as required including removing old existing brach drain, making good to walling rendering, cutting out branch channel and making good benching for 150mm dia pipe complete all as specified and directed.

Returning filling in soft/disinterated rock including spreading levelling and watering and well ramming in layers n exc 25 cm complete all as specified and directed.

Removing excavated material n. exc. 50metre and depositing where directed at a level not exceeding 1.5 metre above the starting point in soils complete all as specified and directed.

Taking down carefully copper/Aluminium point wiring (light/socket/bell/power /point) on teakwood batten /surface conduit /in PVC casing capping along with all fittings/fixtures such as switches , socket out lets , bell push , lamp holder , ceiling roses, regulators and all electrical fittings upto 6 metre height including, making good to the disturbed surfaces of walls/ceilings, floors, roofs etc. complete all as specified and as directed.

Taking down main switches & DBs complete all as specified and directed

Taking down sub main wiring of any size of any height including ERW conduit complete and making good the disturbed surfaces all as specified and as directed.

Material and labour for point wiring with 1.5 Sqmm size, PVC insulated and unsheathed 1100 volts grade single core stranded ( multistrand) copper conductor cable drawn into & including PVC casing and caping of suitable size with all fittings and accessories PVC sleeve/dash fasteners and cadmium plated screws including sunk type pressed steel terminal boxes of 1.6 mm with 3mm thick laminated sheet top cover concealed in walls for provn of switches /sockets fan regulators fixed with MS screws and / cup washers including one continuous run of PVC insulated (green colour1.5sq mm multi stranded copper conductor cable earth wire and connected to earth dolly complete all as specified and directed for the following including providing connector for connection of tubelight fitting and all type of fans, complete all as specified and directed for the following:- a) one light point controlled by one; one way switch.

(b) one fan point controlled by one; one way switch.

(c) one 3 pin socket out let 5 amp (independent) point controlled by one; one way switch.

(d) one 3 pin socket out let 5 amp point on the same board with other switches.

All as per item No-112 above but with 2.5 sq mm size pvc insulated and unsheathed 1100 volts grade single core stranded ( multistrand ) copper conductor cable for 3 pin socket outlet 15 amp on independent board. Including one continuous run of PVC insulated green in colour 1.5 sqmm multistranded copper conductor earth wire connecting to earth dolly complete all as specified and directed.

Supply and fix switch piano, flush type 5 Amps button single pole one way complete all as specified and directed.

Supply and fix switch socket combination 2 pin cum 3 pin 5 Amp, flush type complete all as specified and directed

Supply and fix Switch socket conbination 2in1,3 pin, 5 and 15Amp /16 Amp, flush type complete all as specified and directed.

Supply and fix ceiling rose 3 terminal 240 volts 5 Amps complete all as specified and directed.

Material and labour for sub main wiring using two single core 2.5 sqmm copper conductor and drawn into & including ERW steel conduit including one run of PVC insulated copper earth continuity wire of 2.5sqmm and connected to earth dolly complete all as specified and directed. Note:Two runs of 2.5 sqmm and 1 run 2.5 sqmm cable and one run of ERW steel conduit shall be measured and paid as one length.

Material and labour for submain wiring using two single core 6 sqmm copper conductor and drawn into & including ERW steel conduit including one run of PVC insulated copper earth continuity wire of 6 sqmm and connected to earth dolly complete all as specified and directed. Note:Two runs of 6 and 1 run 6 sqmm cable and one run of conduit/casing caping shall be measured and paid as one length.

Supply and fix MCB DB double door 8 way SPN with 200 Amp rated busbar 240V complete all as specified and directed.

Supply and fix MCB DB double door 4 way VTPN with 400 Amp rated busbar 415V complete all as specified and directed.

Supply and fix MCCB TPN 63 Amps 16 KA ,415 V complete all as specified and directed.

Supply and fix MCB SPN 20 Amps to 40 Amps 10 KA ,240 V complete all as specified and directed.

Supply and fix MCB SP 6 Amps to 32 Amps complete all as specified and directed.

Supply and fix LED tube light fitting 2X18 W, 4 feet long wall mounted anodized aluminum extruded heat shrink provided for efficient heat deception and interchangeable integrated electronic driver luminaries LED as light sources housing at any height complete with all accessories including suitable lamp, internally prewired & including up with twin core twisted flexible copper cable of suitable size all as specified and as directed

Supply and fix LED fitting wall mounted luminaires 9 Watt / 10 watts with polycarbonate housing integrated electronic driver at any height complete with all accessories including internally prewired complete all as specified and directed.

Supply and fix new generation energy saving and enviromental freindly LED street light 25 watt made up of pressure die cast aluminum housing with high power LED as lighting source and lens embedded PC cover having top opening separate driver compartment with IP 66 protection and impact resistance of IK 07 at any height complete all as specified and as directed

Supply and fix high bay light 80 watt with glass including fixing arrangement and accessories at any height complete all as specified and as directed

Material and labour for earthing complete with galvanised steel earth plate electrode 600mm x 600 mm x 6.3 mm thick, buried directly in ground (earth pit not less than 2.25 meters deep below ground level) with top edge of the plate not less than 1.5 meters below normal ground level, connected to galvanised earth lead wire 4.0 mm dia by means of bolts, nuts,check nuts and washers of galvanised iron or steel all as shown in electrical plate No-03 connected to earthing test point all as specified or indicated including testing on completion all as specified and directed by Engr-in-Charge.

Supply and fix ceiling fan complete with and including electronic type regulator and accessories 230 V,1200 mm sweep complete all as specified and directed.

Supply and fix exhaust fans AC single phase 230 V / 240 V of size 300 mm sweep with louver complete all as specified and directed.

Supply and fix Air circulator fan AC single phase 230 V /240 V of size 600 mm variant in sweep with circulating function including making required fixing arrangement on wall complete all as specified and directed. Make : Turbo Force of Havell's/ Usha/ Khaitan

Taking out old unserviceable LT UG cable any size from trench complete all as specifed and directed.

Dismantling/ taking down unserviceable LT panel from site complete all as specified any directed.

Supply, laying and testing of UG cable, XLPE insulated, screened, PVC bedded galvanised steel strip or wire, armoured, electric power cable (heavy duty) with stranded aluminium conductor, 1100 volts grade of size 3.5 core 70 sqmm complete all as specified and directed. Make : Havells, Gloster, KEI

Supply, laying and testing of UG cable, XLPE insulated, screened, PVC bedded galvanised steel strip or wire, armoured, electric power cable (heavy duty) with stranded aluminium conductor, 1100 volts grade of size 4 core 25 sqmm complete all as specified and directed. Make : Havells, Gloster, KEI

Excavation in trenches not exceeding 1.5 metre wide and not exceeding 1.5 metre deep for taking out/laying of HT/ LT under ground cable and getting out in the following type of earth stata complete all as specified and as directed:- (a) Soft/ loose soil.

(b) Hard / dense soil

Returning, filling in including spreading, leveling, watering and well ramming in layers not exceeding 25cm in soils complete all as specified and directed.

Removing surplus excavated soil to a distance not exceeding 50metre depositing where directed at a level not exceeding 1.5metre above the starting point complete all as specified and directed.

Material and labour for dry crushed stone sand filling in trenches to required width at bottom and top of cable cushioning including spreading leveling and consolidation complete all as specified and directed. Note : Punned thickness shall only be measured and paid.

Supply and laying sub class B bricks, old size, laid flat adjacent to each other, perpendicular to cable with width equal to length in trenches for protection of cable complete all as specified and directed.

Material and labour for cutting of roads/ plinth for removal/ lalying of pipe and making good the disturbed surfaces as per existing adjoining surfaces complete all as specified and directed.

Material and labour for PCC 1:2:4 type B-1 by using 20mm graded crushed stone aggregate as in foundations for making good road/ foot path/ hard standing/ drain/ bldg plinth protection complete all as specified and directed.

Material and labour for GI tube, , light grade with all fittings, complete, fixed to walls, pole ceiling or laid in trenches for cable protection all as specified for the size 40mm dia complete all as specified and directed. NOTE :-(Excavation and earth work where required shall be measured separately. MS Clamps for fixing on wall / pole , etc are included in the unit rate).

Material and labour for earthing complete with galvanised steel earth plate electrode 60cm × 60cm × 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less'than 1.5 metres below normal ground level, connected to galvanised earthing strip 32mm x6 mm by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 connected to earthing test point all as specified or indicated including testing on completion complete all as specified and directed.

Supply and fix in repair aluminium strip 25mmx3mm with saddle and fixing screws etc for roof conductors and down conductors above ground level fixed on walls / roof with all neccesary fixing arrangements complete all as specified and directed. Note : Epoxy base insulator and PCC block only will be measured and paid seperately

Supply and fix in repair Test point terminal block made of gun metal or phosphorus bronze size 75mm x 75mm x25mm, drilled and screwed including, 3 NOS, 8mm dia 25mm long hex, head screw complete all as specified and directed by Engineer-in-Charge including dismantling taking out old inspection box.

Supply and fix in repair galvanised iron strip of size 32mm x 6 mm burried in ground or "fixed on wall'' with all neccesary fixing arrangements complete all as specified and directed. Note : 1. Epoxy base insulator only will be measured and paid separely. 2. All GI strip joints should be butt welded atleast 50 mm long.

Supply and fix air termination single pointed aluminium rod of 12mm dia 300mm long including dismantling taking out old air termination complete all as specified and directed.

Supply and fix PCC block of size 150mm x 150mm x150mm in PCC 1:3:6 Type C1 with using 20mm graded crushed stone aggregate for fixing on roof conductor / air terminal rod / GI Strip etc complete all as specified and directed by Engr-in-charge.

Material and labour for Earthing complete with galvanized steel earth plate electrode 60cm x 60cm x 6 mm thick buried directly in ground (earth pit not less than 2.25 metre deep below normal ground level) with the top edges of plate not less than 1.5 metre below normal ground level connected to GI earth strip 32mm x 6mm by means of GI nuts, bolts check nuts and washers earth lead protected by 40mm dia GI pipe light grade and connected to main distribution board/earthing test point all as shown in electrical plate No 3 of SSR part 1 and all as specified including testing on completion. Notes : The unit rate also including for excavation, earth work in any type of strata, plain cement concrete 1:3:6 mix, Type C1, 40mm thick using 40 mm graded crushed stone aggregate RCC 1:2:4 mix, type B1 using 20 mm graded crushed stone aggregate cover reinforced with 8mm dia TMT bars @150mm C/C both ways, GI funnel with GI watering pipe 20mm dia medium grade, wire mesh, protection pipe 40mm dia GI pipe light grade for earth lead upto 7.50metre long including charcool, salt etc complete complete all as specified and directed. Note :- GI strip 32mmx6 mm beyond 7.5 metre will be measred & paid seperately.

Supply and fix earth pit indicator made out of MS sheet of 16SWG of size 30mm x 20cm welded to " angle of size 25mm x 25mm x 3mm at a height 1Metre above ground including dismantling taking out old earth pit indicator complete all as specified and directed.

Material and labour for epoxy base insulator of suitable size 35 mm height fixed on PCC blocks / on wall on MS angle / on towers with and including nut bolts and washers etc complete all as specified and directed by Engineer-in-Charge including dismantling taking out old insulator.

Supply and fix inspection boxes /test point boxes 250mm x150mm x100 mm made out of 16gauge MS sheet with top cover including provisioin of fixing of 2 Nos epoxy insulator with and including insulating PVC sheet for incoming and outgoing copper strip for proper insulation etc complete all as specified and directed.

M/S.J.V.Datar

SHUBHAM SHANKAR GAIKWAD

VIRENDRA FABRICATORS

S.K.HARAL

Mehta Construction Co.

R. K. Industrial Fabricators