CONSTRUCTION OF COLD STORAGE AND OTHER PARAPHERNALIA AT CHITTAPUR TALUKAOF KALABURAGI DISTRICT IN KARNATAKA ON TURNKEY BASIS

Earth work in surface excavation by mechanical means for lowering and leveling the ground for all works other than foundation in all kinds of soils and upto depth not exceeding 300mm as per drawing an...

Earth work excavation for Foundation by mechanical means for all works and depth upto 3 m, as per drawing and technical specifications, including setting out, shoring, strutting, barricading, caution ...

Disposing off excess earth outside the site including loading and unloading, transportation etc., complete.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations and other similar works etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by r...

Earthwork excavation ( in deposited soil ) and filling sides of foundation upto plinth in layers not exceeding 20 cms. in depth, compacting each deposited layer by ramming after watering with lead upt...

Earthwork excavation (in deposited soil) and filling sides of foundation upto plinth in layers not exceeding 20 cms. in depth, compacting each deposited layer by ramming after watering with lead upto ...

Providing and Filling in foundation with granite / trap broken metal 100mm. and Down size and with approved sand including hand packing, ramming, watering, including cost of all materials and labour w...

Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the Material with water at OMC in mechanical mix plant carriage of mixed Materia...

P/c. soak pit, 5000mm dia including earthwork excavation, construction of dry rubble masonry walls, filling hard brick bats with charcoal etc. complete as per details, 2500mm deep.

Providing and laying in position plain cement concrete for levelling course for all works in foundation. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS...

Providing and laying in position Reinforced/ Plain cement concrete for all Sub structures of building, Irrigation works, Sub structure works of bridges, Drain works and other parallel works from 0.50m...

Do for Column Footings / Retaining Wall Footings / Raft / Base Slab

Do for Pedastal with M-25

Do for Plinth Beam with M-25

Do for Lintel with M-25

Do Slab M-25 (Ground Floor-)

Providing and laying 150mm thick RCC Deck slab using M25 grade concrete excluding cost of deck sheets and steel reinforcements including smooth finish on top as per specification. (Ground floor)

Do for Chajja with M-25

Providing and laying in Cement Concrete for all Basement and surface level works, return walls, retaining walls, sunken floors etc. The granite/trap/ basalt crushed graded coarse aggregates and fine a...

Do for RCC Wall with M-30

Do for Slab with M-30

Supplying, fitting and placing TMT FE 550 / 550D Steel Reinforcement including cost of all materials, machinery, labour, cleaning, straightening, cutting, bending, hooking, laping/welding joints, tyin...

Providing RanDom rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1-6-12 (1 cement - 6 coarse sand - 12 graded stone aggregate 20 mm nominal size) up...

Providing and constructing load bearing wall with Solid Concrete blocks of size 400x200x200mm having block density more than 1800kg/m three and minimum compressive strength of 4.00 N/mm2 conforming to...

Providing Brick work with common burnt clay Non Modular bricks of class designation 3.5 in superstructure above plinth level in all shapes and sizes in Cement mortar 1-6 (1 cement - 6 coarse sand) inc...

Providing Half brick masonry with common burnt clay Non Modular bricks of class designation 3.5 in superstructure above plinth cement mortar 1-4 (1 cement -4 coarse sand) including cost of all materia...

Providing Half brick masonry with common burnt clay Non Modular bricks of class designation 3.5 in superstructure above plinth cement mortar 1-4 (1 cement -4 coarse sand) including cost of all materia...

Providing and fixing 1mm thick M.S. sheet Door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a primi...

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid Door/winDow/Clerestory winDows and other Frames/ Chowkhat comprising of virgin PVC polymer of K value 58-60 (Suspen...

Providing and fixing factory made Green certified, Anti Termite, UV resistant, high water absorbant single extruded WPC (Wood Polymer Composite) solid plain flush Door shutter of required size compris...

Providing and fixing factory made PVC Door frame of size 50x47mm with a wall thickness of 5mm, made out of extruded 5mm rigid PVC foam sheet metered cut at corners and jointed 2 No.s of 150mm long bra...

Providing and fixing 30mm thick factory made rigid foam Prelam Panelled Door Shutters made from M.S. tube of 19x19mm, 19 gauge for stiles and 15x15mm for top and bottom rails, covered with heat moulde...

Providing and fixing aluminium work for Doors, winDows, ventilators and partitions with extruded built up standard tubular sections/ appropriate sections and other sections of approved make conforming...

Providing and fixing glazing in aluminium Door, winDow, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of...

Providing and fixing SS fly proof wire gauze to winDows, clerestory winDows and Doors to exsisting aluminium frame. Stainless steel (grade 304) wire gauze of 0.5 mm dia wire and 1.4 mm aperture on bot...

Providing and fixing M.S. grills of required pattern in frames of winDows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to steel...

Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying 2 coats of approved make and shade ena...

Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on spec...

Providing 12 mm cement plaster with Cement mortar 1-3 (1 cement- 3 coarse sand) finished with a floating coat of neat cement to brick masonry including rounding off corners wherever required smooth re...

Providing 15 mm cement plaster on the rough side of single or half brick wall of mix 1-4 (1 cement- 4 fine sand) including rounding off corners wherever required smooth rendering, providing and removi...

Providing 18 mm cement plaster in two coats under layer 12 mm thick cement plaster with cement mortar 1-5 (1 cement - 5 coarse sand) and a top layer 6 mm thick cement plaster with cement mortar 1-3 (1...

Providing 20 mm cement plaster with cement mortar 1-3 (1 cement- 3 coarse sand) finished with a floating coat of neat cement to brick/ stone masonry including rounding off corners wherever required sm...

Providing and constructing un-reinforced plain cement concrete pavement, thickness as per design, over a prepared sub base, with 43 grade cement or any other type as per Clause 1501.2.2 M20 (Grade), c...

Vaccum de-watering with vaccum pump and suction mat and compaction with skin floater clubbed with floating disc including cost of generator, HOM of machinery, Screed Vibratory, Power Floater, blade an...

Cutting transverse contraction joints 3 to 4 mm wide and depth 60mm in concrete slab using concrete cutting machine with diamond studded saw within 4-8 hours of casting of bay / slab etc. complete inc...

Providing to contraction joints polysuphide sealent (Pouring grade) confirming to BS - 5212 - 1989 into sawed groove widened at top for sealent reservoir of specified size and shape as per detailed dr...

Providing and adding approved make Floor hardner in flooring as per details.

Do For Tandur flooring for staircase including edge rounding, polishing etc. complete.

Providing and fixing 1st quality ceramic glazed floor tiles conforming to IS - 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle gr...

Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS- 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle gre...

Providing and laying Cement concrete flooring 40 mm thick with 20 mm nominal size stone aggregate using 1-2-4 (1 cement - 2 coarse sand - 4 graded stone aggregate) finished with a floating coat of nea...

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS - 13592 Type A, including jointing with seal ring conforming to IS - 5382, leaving 10 mm gap for thermal exp...

Ground Floorplus First Floor

Finishing walls with 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489-2004, Alkali and fungal resistance, dirt resistance exterior paint of requir...

Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two coat applied @ 0.90 ltr/10 M squareover an under coat of primer applied @ 0.80 ltr/10 M squareof approved brand and manuf...

Painting wood work with Deluxe Multi Surface Paint of required shade. Two coat applied @ 0.90L/10 M squareover an under coat of primer applied @0.75 L/10 M squareof approved brand and manufacture to g...

Providing and laying 80mm thick factory made precast M -30 grade Cement Concrete Paver Block as per IRC SP 63-2018 and IS 15658 for Commercial Traffic Axle load repetitions upto 10MSA and for Resident...

Providing and fixing All Primary steel including Rafters, Columns shall be Built up Sections made out of plates having a minimum yield strength of 345 Mpa. Grade 50 conforming to ASTM A 572 including ...

Providing and fixing All M.S.Secondry structural Frame including Purlins, Girts shall be made out Cold Formed steel of min yield strength of 250 Mpa including providing and painting 2 coats of anticor...

Providing and fixing Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying painting 2 coats of anti...

Providing and fixing Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying painting 2 coats of anti...

P/F 1.2mm thick G.I. Decking sheets from approved make with crest depth of 52mm made out of high tensiled, structural grade galvanised steel (240MPa yeild strength) sheet for floor including all acces...

Providing and fixing High tension foundation Bolts and nuts of various sizes including foundation bolts at column bases, excluding cost of concrete.fixing to be Done by civil contractor under the supe...

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (plus 0.05 %) total coated thickness with zinc coating 12...

Do For GI Sheet Cladding

Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (plus0.05 %) total coated thickness, Zinc coating 120 g/m2 as per IS- 277, in 240 mpa steel grade, 5-7 microns epoxy p...

Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (plus0.05 %) total coated thickness, Zinc coating 120 g/m2 as per IS- 277, in 240 mpa steel grade, 5-7 microns epoxy p...

Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (plus0.05 %) total coated thickness, Zinc coating 120 g/m2 as per IS- 277, in 240 mpa steel grade, 5-7 microns epoxy p...

Providing and fixing 3mm Clear/opal white poly carbonate profile (matching to the G I roof sheets) sheet . The work including cost of all materials, labour charges and usage charges of machinery for c...

P/F. wind driven Turbo Ventilator of 600mm dia over sheet roof manufactured out of high grade aluminium and stainless steel with all necessary fixing accessories as per manufacturers specifications.

Limit switches with power and control cabling etc. should be provided on each landing, so that cage stops automatically on reaching its desired place. Over-hoisting and Over-lowering limit switches sh...

Providing and fixing M.S. grills of required pattern in frames of winDows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to steel...

Providing and grouting below m.s. columns using GP2 or Equivalent approved make grout as per manufacturers instructions, 50 to 60mm (Max) thick.

Providing and laying Cement concrete pavement with 1-2-4 for commercial and residential building floors, hardpaths, footpaths using 1 cement - 2 coarse sand - 4 graded stone aggregate 20 mm nominal si...

Providing and fixing C.I. frames with cover of approved Ist quality and make conforming to I.S.I. Specification and fixing in C.C. (1-2-4) 7.5 cms thick including curing (Rate includes cost of all mat...

P/F. PVC or equivalant approved make Vent Pipes (Supreme or equivalent make) malleable specials such as , reducing sockets, collers etc. as required including cutting, threading and fixing with necess...

P/F. PVC or equivalant approved make Vent cowl (Supreme or equivalent make) malleable specials such as , reducing sockets, collers etc. as required including cutting, threading and fixing with necessa...

Providing plusB2-B79and laying reinforced cement concrete pipe NP3 for culverts including pointing ends, and fixing collars with cement mortar 1-2 including cost of all materials, labour, curing compl...

Providing and laying 150mm thick RCC Deck slab using M25 grade concrete excluding cost of deck sheets and steel reinforcements including smooth finish on top as per specification. (First floor)

Supplying, fitting and placing TMT FE 550 / 550D Steel Reinforcement including cost of all materials, machinery, labour, cleaning, straightening, cutting, bending, hooking, laping/welding joints, tyin...

Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying 2 coats of approved make and shade ena...

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS - 13592 Type A, including jointing with seal ring conforming to IS - 5382, leaving 10 mm gap for thermal exp...

Finishing walls with 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489-2004, Alkali and fungal resistance, dirt resistance exterior paint of requir...

SANITARY-PLUMBING WORK

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. ...

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge.

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm or 340x410x265 mm sizes respectively.

Providing and fixing PTMT 15 mm Urinal spreader size 95x69x100 mm with 1/2 BSP thread and shapes, weighing not less than 60 g.

Providing and fixing granite stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with c...

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the w...

Providing and fixing CI / PVC Nahani trap of approved make conforming to ISI specifications and construction of Cistern in CC 1:2:4 as per directions (Rate is inclusive of cost of materials and fixtur...

Providing and fixing C.P. brass bib cock of approved quality conforming

Providing and fixing C.P. brass stop cock (concealed) of standard design

and of approved make conforming to IS:8931.

P/F Chorinated Poly chloride (CPVC) pipes conforming to IS 15778, having thermal stabilty for hot and clod water supply inclding all CPVC plain and brass threaded fittings. This includes jointing of p...

P/F Chorinated Poly chloride (CPVC) pipes 25mm dia.

cP/F Chorinated Poly chloride (CPVC) pipes 32mm dia.

P/F Chorinated Poly chloride (CPVC) pipes, having thermal stabilty for hot and clod water supply inclding all CPVC plain and brass threaded fittings including fixing the pipe with clamp at 1.00mtr spa...

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 20 mm nominal bore

ball valve (brass) 25 mm dia:

ball valve (brass) 32 mm dia:

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complet...

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour.

600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 g.

Providing and fixing to wall, ceiling and floor, medium density polyethylene pipes 6.00kgf/sq.cm working pressure outside diameter with special flange, compression type fittings, wall clips, making go...

medium density polyethylene pipes 110mm dia

inspection chamber) 450 X 450 X Upto 600mm Depth

inspection chamber) 600 X 600 X Upto 600mm Depth

REFRIGERATION PLANT AND MACHINERY WORKS

INSULATED PANEL Supply and Erection as per General Technical Specifications , for walls-80 mm thick PIR panels,Density: 40 +2kg /m3 0.5 mm thick Precoated /prepainted

G.S. Sheet (min. 180 GSM) or A...

INSULATED PANEL Supply and Erection as per General Technical Specifications , for walls-100 mm thick PIR panels,Density: 40 +2kg /m3 0.5 mm thick Precoated /prepainted

G.S. Sheet (min. 180 GSM) or ...

INSULATED PANEL Supply and Erection as per General Technical Specifications, for ceiling-60 mm thick PIR panels, Density: 40 +2kg /m3 0.5 mm thick Precoated /prepainted G.S. Sheet (min. 180 GSM) or AZ...

INSULATED PANEL Supply and Erection as per General Technical Specifications, for ceiling-100 mm thick PIR panels, Density: 40 +2kg /m3 , 0.5 mm thick Precoated /prepaintedG.S. Sheet (min. 180 GSM) or ...

INSULATED FLOOR Supply and Erection as per General Technical Specifications Floor 100 mm XPS (in two layers), min 30 kg/cu.m density.

Rate for floor insulation to include supply and erection of all an...

Ancillary Materials and Services - Flashings for Internal and external wall-ceiling joints and wall-wall joints as applicable or as may be required for doors or other openings. The layout showing the ...

Ancillary Materials and Services - Silicon / Polyeurathene sealant for sealing the gaps between panels and the external / internal face of the insulation panels and any other location as may be deemed...

Ancillary Materials and Services - PUF/PIR chemical, adhesives,/ tapes / plastic caps / screws etc reqd for onsite application, as may be necessary for a complete and foolproof insulation job.

Ancillary Materials and Services -SITC of Pressure relief ports suitable for mounting on insulated panels of various thicknesses (60 mm to 100 mm) with internal heaters for room temperatures ranging f...

Ancillary Materials and Services - Making & finishing of cut outs for doors, pipes, cables, pressure ports, ventilatio grills/ diffusers etc as per requirement at site. Finishing would include filling...

Insulated Doors: for CS 1 to 4 - Insulated Doors - Swing type with single leaf 1200 mm x 2100 mm ht x 80 mm thick PIR / PUF

Providing & fixing of Insulated doors (suitable for fitting on panel stru...

Insulated Doors: For Ante-room to dock

Insulated Doors -Swing type with double shutter 2000 mm x 2500 mm ht x min 44 mm thick PIR /PUF

Providing & fixing of Insulated doors (suitable for fitting on ...

Insulated Doors: For Ante-room to dock

Insulated Doors -Swing type with SINGLE shutter 1000 mm x 2000 mm ht x min 44 mm thick PIR /PUF

Providing & fixing of Insulated doors (suitable for fitting on ...

SITC of strip curtains made of 3 mm thick transparent PVC sheet strips

with 40 / 50 mm overlapping and supporting clamps. The strips shall have free swinging motion. The strip materi...

SITC of strip curtains made of 3 mm thick transparent PVC sheet strips

with 40 / 50 mm overlapping and supporting clamps. The strips shall have free swinging motion. The strip materi...

SITC of Dock door, vertically moving with motorized movement. The shutter be made of pre-coated steel sandwich panels 40mm thick injected with PIR / PUF foam (density 40 + 2 Kg/m3) & clear ...

SITC of Retractable type suitable for heavy duty operations for door opening size as above. Polyster type fabric with PVC coating curtain.

Pair of Bumpers -estimated dimensions 250mm (Width) x 100mm (Depth) x 450mm (Height) approx. with heavy steel support

AIR COOLED CONDENSING UNITS For Cold Storage 1,2 & 3 (General details as per REFRIGERATION SYSTEM of GTS)

Complete with Reputed approved make SEMI-HERMETIC compressor working on R134A / R407C, Air...

AIR COOLED CONDENSING UNITS For Cold Storage 4 (General details as per REFRIGERATION SYSTEM of GTS)

Complete with Reputed approved make Scroll /Semi hermetic compressor working on R134A / R407C, A...

AIR COOLING UNITS - Air Cooling Units for Cold Storage 1,2 & 3 (General details as per PART II -REFRIGERATION SYSTEM of GTS)

See specification in tender docment

AIR COOLING UNITS - Air Cooling Units for Cold Storage 4 (General details as per REFRIGERATION SYSTEM of GTS)

Technical specifications as per General Technical Specifications as mentioned in the tend...

Refrigeration Piping, Fittings & Valves (General details as per REFRIGERATION SYSTEM of GTS)

The piping shall be of refrigeration quality The piping shall be of refrigeration quality seamless copper...

Suction line insulation (General details as per REFRIGERATION SYSTEM of GTS)

Suction line insulation with EPDM/ XLPE/Equivalent insulation with minimum 28G Aluminium foil Clading in the covered area...

Drain piping with rigid U-PVC pipe from A.C. units to to suitable drain point complete with 'U' Traps for each cold room and supports.Drain lines (inside the chambers) to have 10 mm EPDM / Eqvt. ins...

Controls and Instruments

(a) Thermostatic expansion valves for each ACUs

(b) Digital temperature indicator cum controllers (0 to 50 deg. C range)

(c) Liquid line solenoid valves, DANFOSS / SPORLAN /...

First charge refrigeration gas and oil etc. as required upto commissioning and final handling over of plant.

Painting of equipment/piping / piping supports etc. as per standard colour codes with initial coat of red oxide primer and two coats of synthetic enamel paint .

Electrical work for Refrigeration System

Electrical control panel shall be manufactured as per specifications menioned in GTS and approved GA drawings.

The Panel shall be comprising of following:

Miscellaneous Items

a) Vibration isolators for condensing units, supporting rods / Frame for A.C. Units with insulation, steel structure for mouting condensing units etc. as may be required

Fabrication and Erection of the duct mouthpieces for Air Cooling Units

Ducting mouthpieces for Air Cooling Units fabricated from G.S.sheet complete with collars, guide vanes, supports etc. as per appr...

Charges for Installation, Testing and Commissioning

Installation, testing and commissioning of all above equipment / material as per the system requirement. All tools and tackles, welding machines, w...

Providing fabricationg and erecting in position Structural Steel (channels, angles etc), for insulated roof/wall panel, dock door supports, primary supports at roof level for ACUs etc. as per approved...

Dimensions: 1000mm X 1200mm X 150 mm approx. ht

Colour: as approved by client

Pallet type: four side fork opening

Weight carrying capacity: 1500 Kg

Suitable to use with all kind of material ha...

Hydraulically Operated Hand Pallet Truck

Type : Hydraulically operated Hand Pallet Truck

Manufacturer : Godrej / Linde / Jungheinrich / Nilkamal / Eqvt.

Model No. : to be mentioned

Load Capacity in k...

Fly Catcher / Insect Killer

Supply & fixing of industrial type fly catcher / insect killer, 2 feet model, Stainless Steel Body 304 with stainless steel screws and stainless steel grills with UV lamp 1...

Platform type Weighing balance

Capacity: 100 Kg with 10g accuracy

Full body in SS construction,

Protected internal calibration

Red color 12.5 mm LED display pole type

Built in battery backup

Supply & fixing of industrial type air curtains suitable for door clear opening size as mentioned and specifications given below.

The Air Curtains shall incorporate centrifugal blowers m...

Miscellaneous Items :

SITC of Hi-wall type split AC units, BEE 3 star rated (suitable for cooling mode only) including condensing unit and indoor unit with necessary refrigerant piping, duly insulate...

IOT type Data logger with facility to monitor & record data of temperature & relative humidity of all 4 cold chambers from PC, Mobile etc. The data logger shall have RS-485 port, USB facility, softwar...

Year 1 (after 1 year of defect liability period)

Year 2 (after 1 year of defect liability period)

Year 3 (after 1 year of defect liability period)

ELECTRICAL WORKS

Supply, erection, testing & commissioning of RCC DP/SP structure as per EB including foundation, painting of structure and materials like GOS, LA's, DOLO fuses, ACSR conductors, insulators, H- frame a...

Supply, installation testing and commissioning of 630A, 11KV, outdoor, load break switch and necessary accessories all complete as required by BESCOM. The rate shall exclude cost of necessary civil wo...

Supplying erection, testing and commissioning of 11kV , VCB panel, suitable for outdoor application as per Data sheet-1 complete as per latest IS standard technical specification.

Supply, installation, testing and commissioning of 11kV HT metering cubicle with 3CT's, 3 PT's and 3 phase 4 wire methodology with necessary accessories all complete as required by ESCOM. The rate s...

Supply, installation, testing & commissioning of following, 11kV/433V, 200 kVA copper wound, oil filled transfomer (as per IS-1180 level -2) with off load tapping of -/+ 5% in steps of 2.5%. The trafo...

LT Cable laying 3Core x 95 Sqmm

Out door (3Core 95Sq mm. cable)

Indoor (3Core 95Sq mm. cable)

Supply and fixing of chain link fencing alround the transformer yard and HT yard fencing as per drawing using M.S.pipe, vertical support of 2200mm high including concrete foundation & necessary civil ...

LT Kisosk '(As per dwg no. CS&MP/PECS-2511/EL-SCH-01)

SDB-Millet process '(As per dwg no. CS&MP/PECS-2511/EL-SCH-01)

SMP-Cold store '(As per dwg no. CS&MP/PECS-2511/EL-SCH-01)

SDB- Utility '(As per dwg no. CS&MP/PECS-2511/EL-SCH-01)

Fire pump panel '(As per dwg no. CS&MP/PECS-2511/EL-SCH-01)

SDB-Cold store '(As per dwg no. CS&MP/PECS-2511/EL-SCH-01)

6 Way TPN MCB DB

1 No. 32A 4P RCCB 100mA + 32A TPN MCB

18 nos. of 6/10A SP MCBs

8 Way VTPN MCB DB

1 No. 40A 4P RCCB 300mA + 40A TPN MCB

14 nos. of 6/10/16A SP MCBs

3 nos. of 16A TP MCBs

4 Way TPN MCB DB

Incomer :1 No. 25A 4P RCCB 100mA + 25A TPN MCB

Outgoings : 12 nos. of 6/10A SP MCBs

12 Way SPN MCB DB

Incomer : 25A DP MCB

Outgoings : 8 nos. of 6/10A SP MCBs

6 Way SPN MCB DB

Incomer : 25A DP MCB

Outgoings : 4 nos. of 6/10A SP MCBs

4Way TPN MCB DB

Incomer : 1 No. 25A TPN MCB

Outgoings : 7 nos. of 10/16A SP MCBs

2nos. 16A Astronomical timer Switch

4 Way VTPN MCB DB

1 No. 32A 4P RCCB 300mA + 32A TPN MCB

1no. 32A TP MCB

3 nos. of 6/10A SP MCBs

Al. cable 3.5C X 300 Sq.mm arm.

Al. cable 3.5C X 185 Sq.mm arm.(DUMYY ITEM ONLY TO BE EXECUTED IF REQUIRED WITH PRIOR APPROVAL)

Al. cable 3.5C X 150 Sq.mm arm.

Al. cable 3.5C X 120 Sq.mm arm.

Al. cable 3.5C X 95 Sq.mm arm.

Al. cable 3.5C X 50 Sq.mm arm.

Al. cable 3.5C X 35 Sq.mm arm.

Al. cable 4C X 16 Sq.mm arm.(DUMYY ITEM ONLY TO BE EXECUTED IF REQUIRED WITH PRIOR APPROVAL)

Al. cable 4C X 10 Sq.mm arm.

Al. cable 4C X 6 Sq.mm arm.

Al. cable 4C X 4 Sq.mm arm.

Al. cable 3C X 70 Sq.mm arm.

Al. cable 3C X 10 Sq.mm arm.

Al. cable 3C X 6 Sq.mm arm.

Al. cable3C X 4 Sq.mm arm.

Al. cable 3.5C X 300 Sq.mm arm.

Al. cable 3.5C X 185 Sq.mm arm.(DUMYY ITEM ONLY TO BE EXECUTED IF REQUIRED WITH PRIOR APPROVAL)

Al. cable 3.5C X 150 Sq.mm arm.

Al. cable 3.5C X 120 Sq.mm arm.

Al. cable 3.5C X 95 Sq.mm arm.

Al. cable 3.5C X 50 Sq.mm arm.

Al. cable 3.5C X 35 Sq.mm arm.

Al. cable 4C X 16 Sq.mm arm.(DUMYY ITEM ONLY TO BE EXECUTED IF REQUIRED WITH PRIOR APPROVAL)

Al. cable 4C X 10 Sq.mm arm.

Al. cable 4C X 6 Sq.mm arm.

Al. cable 4C X 4 Sq.mm arm.

Al. cable 3C X 70 Sq.mm arm.

Al. cable 3C X 10 Sq.mm arm.

Al. cable 3C X 6 Sq.mm arm.

Al. cable 3C X 4 Sq.mm arm.

50 mm outer dia/38mm inner dia

110 mm outer dia/95mm inner dia

160 mm outer dia/135mm inner dia

200 mm outer dia/174mm inner dia

Excavation of trench of 900 mm deep and of required width for laying of cables/ humepipes. The rate shall include cost of refilling the excavated portion and consolidating etc., as required. The rate...

Supply and laying of sand cushioning for under ground cables laid in existing trench.

Supply and laying of brick protection for under ground cables laid in existing trench.

galvanized 50 mm (W) x 50mm (H) with cover

galvanized 100 mm (W) x 50mm (H) with cover

galvanized 200 mm (W) x 50mm (H) with cover

galvanized 300 mm (W) x 50mm (H) with cover

galvanized 400 mm (W) x 50mm (H) with cover

Hot Dipped Galvanized Iron ladder type cable trays with rungs 300 mm x 50 mm x 1.5 mm

Hot Dipped Galvanized Iron ladder type cable trays with rungs 200 mm x 50 mm x 1.5 mm

Hot Dipped Galvanized Iron ladder type cable trays with rungs 100 mm x 50 mm x 1.5 mm

Supply and fixing of conduit / structural steel support ceiling suspended type / wall bracket type clamps with necessary saddles for fixing of conduits / cables, cable trays and where ever necessary. ...

Short point upto 3m

Medium point above 3 mtrs upto 6 mtrs.

Long point above 6 mtrs upto 10 mtrs.

Two in a row above 3 mts upto 6 mtrs from tapping point to outlet via switch box

Three in a row above 6 mts upto10 mtrs from tapping point to outlet via switch box

Ceiling fan point controlled by 6A modular type switch and fan regulator. Medium point above 3 mtrs upto 6 mtrs.

Long point above 6 mtrs upto 10 mtrs.

Exhaust fan point (Single phase) controlled by 6A modular type switch and 6A socket outlet near the exhaust fan - Medium point above 3 mtrs upto 6 mtrs.

a,2x1.5 Sqmm +1x1.0 Sqmm PVC Insulated wires drawn in 20mm dia PVC conduit for additional length of point wiring.

b, 2 x 2.5 Sqmm + 1 x 1.5 Sq mm PVC Insulated wires drawn in 20 mm dia PVC conduit

c, 2 x 4 Sqmm + 1 x 2.5 Sq mm PVC Insulated wires drawn in 20 mm dia PVC conduit

d. 2 x 6 Sqmm + 1 x 4 Sq mm PVC Insulated wires drawn in 32 mm dia PVC conduit.

e. 4 x 2.5 Sqmm + 2 x 1.5 Sq mm PVC Insulated wires drawn in 25 mm dia PVC conduit

f. 4 x 4 Sqmm + 2 x 2.5 Sq mm PVC Insulated wires drawn in 25 mm dia PVC conduit

g. 4 x 6 Sqmm + 2 x 4 Sq mm PVC Insulated wires drawn in 32 mm dia PVC conduit.

h. 4 x 10 Sqmm + 2 x 6 Sq mm PVC Insulated wires drawn in 40 mm dia PVC conduit.

I. 4 x 16 Sqmm + 2 x 10 Sq mm PVC Insulated wires drawn in 40 mm dia PVC conduit.

flush mounting powder coated metal box 1 to 2Way

flush mounting powder coated metal box 3 Way

flush mounting powder coated metal box 4-5 Way

flush mounting powder coated metal box 6 Way

flush mounting powder coated metal box 8 Way

flush mounting powder coated metal box 10-12 Way

superior quality modular switch mounting polycarbonate plate 1 to 2 module

superior quality modular switch mounting polycarbonate plate 3 Module

superior quality modular switch mounting polycarbonate plate 4 module

superior quality modular switch mounting polycarbonate plate 6 module

superior quality modular switch mounting polycarbonate plate 8 module

superior quality modular switch mounting polycarbonate plate 10-12 module

6Amps one way switch.

6Amps 3way socket.

16Amps one way switch

6/16Amps universal socket

Stepped Fan Regulator.

a.16A, 3P+N+E, 3- phase socket with plug top

b.16A, 2P+E, 1- phase socket with plug top

c.120W LED, IP65 Industrial, High bay light fixture of type LHB11-120-CDL/60-M of CG make/equivalent.

LED square or round down light 5-6W

LED square or round down light 10-12W

LED square or round down light 15-18W

LED light fitting 1 x 4' - 20/22 W

LED light fitting 1 x 4' - 36/40 W

Supplying of 40 W LED IP-65 Tube Light fixture of type CIS-300-40-57-SL-DP-NGR of CG make/equivalent.

Supplying of 20 W LED IP-65 Tube Light fixture of type CIS-300-20-57-SL-DP-NGR of CG make/equivalent.

a.10W LED, bulk head light fixture of type LBHE-10-CDL of CG make/equivalent.

Fixing all types and all capacities fluorescent / false ceiling / spot light / CFL / LED fittings indoor on the wall / ceiling/ rafters / girders using 23/0.0076” twin twisted PVC insulated wires, ...

Supply and fixing of heavy duty oscillation type propeller fan available with impeller consisting of 3 blades in bracket type, column /wall mounted, 450mm sweep, 1-Phase, of Havells make/equivalent.

Supply , installatin, testing & commsioining of 1000CFM heavy duty exhaust air fan with bracket blades suitable to operate on 250v 50hz,ac supply including should have louvers and Steel Mesh to avoid ...

Supplying capacitor type ceiling fan complete with down rod blades, shackle, canopies etc., for operation on 230 volts, and 50 cycles. Single phase AC supply conforming to IS-374-1979 and with double...

Fixing a ceiling fan of all capacities and all types with necessary clamps & S hook made out of 15mm dia MS rod, with 5 amps ceiling rose of approved quality with necessary length of 23 / 0.0076 inch...

Supplying exhaust fan of 1440 RPM of 300mm (12") size with bracket blades complete for light duty suitable for operate on 230V 50Hz, AC Supply.

Fixing one exhaust fan in the nitch already left in the wall with bolts and nuts and 5 amps ceiling rose with sufficient length of 23 / 0.0076 inch PVC insulated twin core wire of approved make.

Supplying, fixing and wiring earth electrode for grounding of Lifts, Transformers, DG sets etc., Using 40 mm dia 2.9mm thick 2.5mtrs long GI pipe with GI funnel with mesh and suitable size reducer fi...

Supplying and running of GI strips for grounding connections, using necessary fixing materials as required - 25x3mm GI strip

Supplying and running of GI strips for grounding connections, using necessary fixing materials as required - 25 x 6 mm GI strip

Supplying and running of GI strips for grounding connections, using necessary fixing materials as required - 8 SWG, GI Wire

Supying and running of GI strips for grounding connections, using necessary fixing materials as required - 25 x 6 mm Copper strip

Supplying and running of GI strips for grounding connections,using necessary fixing materials as requird - 25 x 3 mm Copper strip

coppr plate 600 x 600 x 3 mm

6 meters - Top 70mm and bottom 130mm dia

9 meters - Top 70mm and bottom 155mm dia

Single Arm Bracket with 1000mm Standard 40/50MM dia

Double Arm Bracket with 1000mm Standard 40/50MM dia

Using 32mm dia G.I.Pipe

Supply, installation, testing and commissioning of gate light pole of MS pole of 50 mm dia, 600 mm long, of which 300mm above the brick wall and 300mm embeded in brick work along with 16 G, 19 mm, PV...

LED Streetlight 70 Watts

LED Streetlight 120 Watts

Fixing halogen/metal/LED flood light fitting over existing pole including clamps, bolts, nuts, and wiring using suitable capacity wires

LED Post Top Lantern with 15/20 W

Fixing charges of post top / Gate/ Garden fitting/ LED on the existing CI /GI or any other pipe using required size of reducer, wiring using suitable wires.

Supply & fixing of 2000 mm Vertical Airterminal of dia 16-10 mm with Complete Support of Roof stand selected as per angle of protection chart to meet the requirement of IS/IEC 62305. Tested for Elect...

Supply & fixing of Bridging cable to interconnect air terminal and down conductor to meet the requirement of IS/IEC 62305 .Tested for Electrical, Mechanical and Chemical as per IEC 62561. The Bridging...

Supply & fixing of Stainless Steel Clamping shoe to interconnection of air terminal and down conductor for metal building to meet the requirement of IS/IEC 62305 Tested for Electrical, Mechanical and ...

Supply & fixing of 8mm Dia Aluminum Solid Round Conductor for down conductor as per required LPL and should be tested for electrical resistivity, Tensile strength, Yield strength%elongation, salt spra...

Supply & fixing of Conductor Holder for fixing the conductor for holding 8 mm Aluminium Round solid Conductor to meet the requirement of IS/IEC - 62305. The condutor hoder shall be of type PCH 8 of Ca...

Supply of Stainless Steel Test Joint suitable connector for 8 mm round Al. conductor & Flat conductor to meet the requirement of IS/IEC - 62305. The test joint shall be of type TJRF of of Cape make / ...

Supplying, fixing and wiring earth electrode for grounding of Lifts, Transformers, DG sets etc., Using 40 mm dia 2.9mm thick 2.5mtrs long GI pipe with GI funnel with mesh and suitable size reducer fi...

Supplying and running of GI strips for grounding connections, using necessary fixing materials as required - 25x3mm GI strip

Supplying and fixing of modular switch/ Socket / telephone socket etc., on existing modular switch plate as per IS 3854 and IS 1293. - Telephone socket

Supplying & drawing PVC flexible 2 pair telephone unarmoured tinned copper cable.

Supplying & Laying of 2mm thick, heavy guage PVC conduit pipe in the concealed slab / groove cutting with suitable size bends, collars, clamps, metal junction boxes adhesive paste etc., and running b...

Supplying & installing of multicore 0.61mm, copper conductor, PVC insulated, PVC sheathed, armoured telephone cable laid drawn through,existing conduit with all necessary accessories as required. 5 pa...

Supplying and fixing of MDF krone juntion box with KRONE module / Telephone cable termination.- 5 pair - Supplying & Fixing

PVC Conduit - Supplying & laying 25mm dia

Supplying and fixing of modular Socket on existing modular switch plate as per IS 3854 and IS 1293. RJ45/I.O outlet

Supplying and drawing UTP -CAT 6E LAN cable

Supply, installation , testing & commissioning of managed L2 8 port 10/100/1000 Switch with 2 Gig SFP. The switch shall be mounted on existing rack. The rate shall also include cost of power supply ...

Supply and fixing of patch panel with CAT-6 I/O mounted on existing rack with all necessary fixing accessories. The rate shall also include providing end termination. 16 port 10/100/1000 patch panel

Supply and fixing of …mtrs cat 6 patch cable- 1 mtr

Supply and fixing of …mtrs cat 6 patch cable- 2 mtr

Supply and fixing of switch wall mounting closed rack with power manager and cable manager - 9U with 450mm depth with all necrssary accessories as required.

kVA at 0.8 p.f, 1500 rpm, Diesel Generator with alternator 125 kVA / 160kW

AMF panel suitable for .....kVA DG set 125 kVA / 160kW

100 mm dia, M.S. pipe with rockwool lagging and aluminium sheet wrapping.

Supply and erection of structural support for exhaust pipe using necessary MS frame work. The sructural support shall be made out of MS frame work using adequate size MS angles. (The vendor shall visi...

Professional Charges towards incidental expenses for obtaining approval from CEIG, EB and NOC from pollution control board for installation of 1no. 160.0 kVA DG sets.

MCC panel-fire fighting( all other specification refer tender documents)

PVC Conduit 20mm dia

PVC Conduit 25mm dia

PVC Conduit 32mm dia

Inside size of 450 x 450 mm depth not exceeding 600mm including providing 450 x 450mm RCC cover.

RCC cover 750mm x 750mm x 900 mm depth with 750x750mm

Supply & Laying of rubber mats of 11kv grade, 1.8.mtr. x 0.9mtr X 2.5mm (thick) and of sufficient thickness as required by the Electrical Inspectorate and confirming to IS 15652

Providing rubber gloves of electrical quality tested to 11 KV.

Fixing of first Aid box containing medicines for 50 persons to give first aid treatment.

Supply and fixing in position approved shock treatment chart written in English, Hindi and local language. The chart shall be framed in teakwood frame and covered with glass.

Supply & Fixing of DANGER / NO ADDMISSION. / NO SMOKING / Board made out of MS sheet metal with 2 coats of non-corrosive enamelled paint of approved shape and size as specified by local electric...

Supplying, erecting, testing & commissioning of 2kVA OFF- LINE UPS system suitable for operation on 230V, 50Hz, A/C supply, with all accessories complete and with 15 min back up. The rate shall includ...

Liasoning charges for obtaining 125 kVA power on HT supply. The rate shall include all incidential expenses towards filling application,getting feasibility report, estimate, power sanction from EB an...

B class medium duty G.I. pipe conforming to IS 1239 25 mm

B class medium duty G.I. pipe conforming to IS 1239 32 mm

B class medium duty G.I. pipe conforming to IS 1239 40 mm

B class medium duty G.I. pipe conforming to IS 1239 50 mm

B class medium duty G.I. pipe conforming to IS 1239 65 mm

B class medium duty G.I. pipe conforming to IS 1239 80 mm

B class medium duty G.I. pipe conforming to IS 1239 100mm

C class medium duty M.S. pipe conforming to IS 1239 150 mm

PN 16 80 mm dia

PN 16 50 mm dia

Pendent Sprinkler

sprinkler flexible pipe (UL Listed) of stainless steel complete 1000mm

Single headed Gunmetal

first-aid Hose Reel with MS construction spray painted in post office red 30M, Long

Supplying Installing, testing and commissioning of Hose cabinet made out of 18 gauge M.S.Sheet with double glass door with lacing arrangement and painted with two coats of Fire red Enamel paint at out...

FLOW SWITCH on sprinkler distribution header 100 mm dia

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required 150 mm

Wraping and Galing of U/G pipe line work includes one coat of anti corrossion paint (Black), including cost of materials, labour, usage charges of machinery complete as per specifications.

Electric pump -2280 lpm at 70 mtrs head

Diesel pump 2280 lpm at 70 mhead

electric driven pressurisation pump 180 lpm at 70 m Head

Supplying and fixing air vessel made of 250 mm dia, 8 mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal whe...

Supply & Installing of 200mm dia Vortex Plate inside Fire Sump with necessary fittings

Providing, installation, testing and commissioning of stainless steel Y-strainer fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet with 3 mm dia holes with stainless steel flange.150mm ...

Single arch Neoprene Rubber Expansion Bellows with MS split retainer rings and control units drilled to ANSI CL 150 SS304 Single axial metallic bellows with MS fixed flanges and tie rods 100 mm

Single arch Neoprene Rubber Expansion Bellows with MS split retainer rings and control units drilled to ANSI CL 150 SS304 Single axial metallic bellows with MS fixed flanges and tie rods 150 mm

Providing & fixing of pressure switch in M.S. pipe line including connection etc. as required.

heavy duty MS pipe conforming to IS 3589/IS 1239 100 mm

heavy duty MS pipe conforming to IS 3589/IS 1239 150 mm

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of followi...

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of followi...

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required : 100 mm dIa

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required : 150 mm dIa

Supplying, fixing, testing & commissioning of double flanged sluice valve of rating PN 1.6 with non rising spindle, bronze/gun metal seat, ISI marked complete with nuts, bolts, washers, gaskets and co...

Supplying, fabricating, STRUCTURAL STEEL SUPPORTS such as MS channels, angles, flats, rods as required at site with anchor fasteners, clamps, threaded rods, nuts, bolts, washers etc. complete with pai...

Pre-fab modular water storage tanks 50,000 lit

Zincalume (ZnAl)(G -300, AZ 150) Sheet of reputed Make, Cylindrical, Vertical, Dome Roof & Flat Bottom with necessary accessories.

Providing 2 kg C02 Gas Type Fire Extinugisher Squeeze grip type, used Unused Mechanism, Squeeze Grip, Gross Weight 9.1 kg empty Weight 7.1 kg Can Height 595 mm Diameter 108 mm, Discharge Time less tha...

Providing 6 kg Fire Extinguisher Mono Ammonium Phosphate Powder 90, Stored Pressure Type, Pressure Gauge, Gross Weight 9.40 kg, empty weight 3.4 kg, Can Height 480 mm, Diameter 160 mm, Discharge Time ...

Al. XLPE Cable 3C 50 Sq .mm

Al. XLPE Cable 3C 10 Sq.mm

Al. XLPE Cable 3C 50 Sq .mm

Al . XLPE Cable3C 10 Sq.mm

outer dia 50 mm