ADDN ALTN TO BLDG NO P 118 AT HQ NORTHERN COMD AND SPL REPAIRS TO TOILET AND ROOF TREATMENT TO BUILDING NO NP 3 AT AVN BASE OF 9 I R and O FLT UNDER GE SOUTH UDHAMPUR

Amount

Excavating in post holes ( or similar holes ) each n. exc 0.5 cum in soft /loose soil getting out, returning filling in and ramming around in layers not exceeding 25cm complete all as specified and as directed.

Excavating over areas, n exc 1.5m deep and getting out in any type of soil, complete all as specified and as directed.

Excavation in trenches and exceeding 1.5m wide and not exc 1.5m in depth in hard/dense soil and getting out all as specified.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in any type of soil, complete all as specified and as directed.

Removing excavated soils n exc. 50m and depositing where directed at a level n exc. 1.5m above the starting point complete all as specified and as directed by the Engineer-in-Charge.

PCC 1:2:4 Type B2 using 40mm graded aggregate as in foundations, filling and mass concrete complete all as specified and as directed.

Hand rails, half round or other stock section or core for wooden hand-rail straight portion drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embedding in concrete and screwing etc. wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc complete all as complete all as specified and as directed.

Rolled mild steel Fe-410w (Gde-E-250) quality 'B' Roof trusses (framed ) , trussed, purlins, crane gantries , rails and fastening and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces cleats etc complete all as specified and as directed.

Pre-painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self tapping screws complete all as specified and as directed.

Pre-painted galvatume aluminum zinc coating GI based Plain steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self tapping screws complete all as specified and as directed.

Solid PVC wall lining consisting of 5mm thick wood grain colour printed PVC sheet inclusive of solvent cement and fixing at site including PVC frame complete all as specified and directed.

Brick work with sub class 'B' bricks exc 6m mean radius straight or curved on plan built in cement mortar 1:6 including demolition of old brick/stone masonry complete all as specified and as directed.

Random rubble masonry built in cement mortar 1:6, uncoursed, well bonded, bedded and solidly hearted complete all as specified .

Raised pointing to random or polygonal rubble, uncoursed on brought upto courses random rubble stone masonary in cm 1:3 complete all as specified and as directed.

Rendering 10mm thick in CM 1:6 on fair faces of brick/concrete finished fair and even without using extra cement complete all as specified and as directed.

PCC 1:2:4 using B1 (20mm graded aggregate) for coping, corner of roof and similar work complete all as sepcified and directed.

Rendering 15mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 finished fair and even without using extra cement complete all as specified and as directed.

Preparation of new steel surfaces of any discripton not otherwise discribed over 10 cm width or girth and applying two coats of synthetic enamal paint over a coat of red oxide on steel surfaces complete all as specified and as directed.

Providing 50 mm thick cement concrete ( 1:4:8) type D2 using 20 mm graded aggregate as in sub base for hard paved area all as specified and directed.

Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and as directed.

Dura stone heavy duty vitrified tiles of size not exc 0.36 Sqm of 10-12mm thick as in floors set and jointed in neat cement slurry and pointed in white cement to match the surface including 15mm thick screed bed in CM 1:6 complete all as specified and as directed.

Dismantling floor, hearth or wall tilling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish of the premises as specified and directed.

Vitrified ceramic tiles (Double charge glossy finish), area of each tile exc 0.42sqm but not exc 1.00 Sqm, 10mm thick (square or rectangular) of superior quality as in floor surfaces set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles and including 15 mm thick screed bed in CM 1:6 complete all as specified and directed.

Double charge vitrified ceramic tiles, area of each tile n exc 0.36 Sqm, 10mm thick (square or rectangular) of superior quality as in walls surfaces set and jointed in neat cement slurry and pointed in white or coloured cement to match the light shade of tiles including 10mm thick screed bed in cement mortar 1:4 complete all as specified and directed.

Non skid ceramic tiles 7 to 8mm thick (Square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6 complete all as specified and as directed.

Glazed Coloured Ceramic tiles in vertical surface 300x600x7mm thick laid over 10 mm thick screed bed in CM 1:4, set and joint in neat cement slurry and pointed in white or colour cement to match complete all as specified and as directed..

10-12 mm thick gypsum boards seamless false ceiling including sunk or raised moulding or cop design to cater decorative LED lights as approved by Engr in Chargge, moisture resistant, including GI hanging wires & frames with intermediate, perimeter channel ceiling channel, along nuts and bolts connecting plates gypsum boards, dry wall screws soffits cleats, ceiling section, rawel plugs fixtures and screws and applying two coats of emulsion paint over a coat primer on exposed surface complete all as specified and as directed. Note : (a) Design of ceiling board as approved by GE. (b) GI grid/hanging system shall be of the same make as of false ceiling manufacturer complete all as specified and as directed.

S&F mild steel framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified .

S&F Anodised aluminium window and ventilator shutters with chowkats, side hung type without sash bar aluminium section weighing 0.55 kg/m including necessary joining cleat , glazing clips, rubber packing, frosted glass 4mm thick, anodised aluminium snap beading screws , anodised aluminium fitting such as peg stays 150mm long (1 no) hinges type B-12 100mm long (2 no ) suitable handle (1 no) etc complete all as specified.

Kitchen cabinet/cupboard in required size at site made out 18 mm thick one side decorative lamination sheet consisting of carcass/HDMR board 18/20 mm thick PVC sheet/sunmica laminated on one side & provn of shutters made out of 18mm thick one side decoartive laminated PVC sheet all reqrired brackets 5.5 screws etc. the panels shall be fabricated using adhesive and screws where ever required. All the edges shall be covered with 2 mm thick edge bonding tape or 90 degree edge bent finish, necessary drawer, openable shelve with frame work/sliders complete as per make and specification mention as per drawing with locking arragement approved by Engr-in-Charge. Colour as approved by GE. (Make: Rajshree/Sintex or equilent) Complete all as directed.

PVC steel catcher of superior quality all as specified and directed by Engr in charge or Garrison Engineer.

Hetich softcloser hinges of stainless steel premium quality complete all as specified and as directed.

Fancy type Brass handles 100mm size fixed with screws, complete all as specified and as directed.

30 mm width of flap Continous (Piano) hinges, mild steel, bright finish or electro galvanised complete all as specified and as directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) not exc. 1.5 sqm each and removing to store complete all as specified and as directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) exc. 1.5 sqm but n.exc 4 sqm each and removing to store complete all as specified and as directed.

Supply and fixing factory made uPVC white colour Casement door with 3D hinges made of (big series) frame 67 x 64 mm & sash 67 x 110 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of door upto 2.00 sqm) comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, zinc alloy (white powder coated) 3D hinges and one handle on each side of panels along with zinc plated mild steel multi point locking having transmission gear, cylinder with keeps and one side key, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws, etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality complete all as specified and directed by Engineer-in Charge. (Glass shall be paid separately) Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.

12mm toughned glass including etching design on glass as approved by Enger in Charge as in hinged doors, partitions automatic doors and similar work including cutting to shape, drilling holes, 18" SS handle, locking system etc as required complete all as specified and as directed.

Supply and fixing factory made uPVC white/coloured fixed glazed window/ventilator/Partition walls made of (small series) frame 47 x 50 mm mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area upto 0.75 sqm.) comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Glass shall be paid separately).

Supply and fixing factory made uPVC white colour Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) upto 1.50m height made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm) comprising of uPVC multi?chambered frame, with inbuilt roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, complete all as specified and directed by Engineer-in-Charge. (Glass or wiremesh shall be paid separately) Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made

5mm glass including etching as approved by Engr in Charge as in windows, partitions automatic doors and similar work including cutting to shape, drilling holes required complete all as specified and as directed.

Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified.

18-20 mm thick granite (of any type) work( table rubbed and polished) in steps, jambs, pillars, window sills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite slab complete all as specified and as directed.

Venetian blinds of vertical/horiozonatal type using 100mm wide fabric blinds of approved colour/ shade and pattern including operating arrangement such as chord/ thread, rolling arrangement, counter weight, connecting chain etc., and necessary fittings complete all as specified and directed.

Taking down cement plaster on brick or stone walls etc. including raking out joints, hacking for key scrubbing down with water etc complete all as specified and as directed.

Wall cladding tiles exterior store series of size 600 mm x 300 mm x 8-10mm thick on vertical surfaces set and jointed in neat cement slurry and pointed in white cement mixed with colour pigments to match the existing surface including 10mm thick backing coat in cement mortar 1:4 complete all as specified and directed.

Roughening surfaces of old concrete surfaces by picking up, sweeping, cleaning and washing down with water to remove dust etc including taking down tarfelt and brushing neat cement slurry @ 3 kg/Sqm including 15mm thick screeding in CM (1:4) finished even and smooth mixed with water proofing compound (WPC shall be measured and paid separately). Applying bituminous primer on roof surfaces @ 0.40 ltr/Sqm and applying one coat of hot blown bitumen of grade 85/25 @ 1.20 Kg/Sqm and provide modified polymeric APP (Atactic Polypropylene) Modified Polymeric Membrane with 100 micron high molecular high density polyethylene film. Min wt of membrane will be 3.50 Kg/Sqm and bonded completely to the surfaces with min end overlap of 15 cms and side lap 75 mm (overlaps to be bounded with thermo fused by flame) and over APP applying one coat of hot blown bitument 85/25 @ 1.2 Kg/Sqm blinded with fine sand in dry condition @ 0.5 Kg/Sqm, complete all as specified and as directed by Engr-in- Charge or Garrison Engineer.

1000 Litres rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I and PTMT ball valve 20mm dia including taking down of old tank and removing from site complete all as specified and as directed.

Repairs Gun metal globe or gate valve 20mm , with iron wheel head screwed both ends for iron pipe complete all as specified and as directed.

15mm bore GI tubing (medium grade) with all fittings and fixed complete to walls and ceiling or laid in floors/roofs including taking down old tubing, complete all as specified and as directed.

20mm bore GI tubing (medium grade) with all fittings and fixed complete to walls and ceiling or laid in floors/roofs including taking down old tubing, complete all as specified and as directed.

S&F in repair countertop vitreous chinaware wash hand basin (WHB) white size 550mm x 400mm complete including provision of pair of mild steel angle iron brackets of suitable size duly painted, 32 mm dia chromium plated waste coupling, PVC waste pipe and cutting for pinning in ends of brackets in wall etc complete.Make : Jaquar Make :KUS-WHT-35601 or its equivalent in Hindware/Cera

S&F in repairs 5 mm thick looking mirror of required size, fixed on walls with dash fasteners and chromium plated screws purposefully made to fix the glass by drilling hole in the glass complete all as specified and as directed.

S&F in repair Water closet single piece/wall hanged pattern coloured of size 535 x 380 x 400 mm in repair as approved and complete all as specified and directed by Engr-in-Charge .Make : Jaquar Cat part No KUS-WHT-35851S300UF or equivalent in Hindware/Cera

S & F in repairs 15 mm dia WHB mixer chromium plated screwed down high pressure with crutch or butterfly handle screwedboth ends for iron pipes or for unions and fixed complete all as specifie and as directed. Make - Jaquar Cat No KUP-35011BPM or equivalent in Hindware

15 mm bore Bib tap in repair complete all as specified and directed. Make : Jaquar Cat Part No CON 107KN and equvalent in CERA.

S&F in repairs 15 mm dia Angle valves/ stop cock ,fancy type and chromium plated screwed down highpressure with crutch or butterfly handle screwedboth ends for iron pipes or for unions and fixed complete all as specified and as directed. Make - Jaquar Cat No KUP-35053PM or equivalent in Hindware

S&F in repairs PVC connection 15 mm size with PTMT nuts 600mm long, fixed in repairs, complete all as specified and as directed.

Health faucet ABS body with wall hook and 1 mtr chrome plated PVC hose pipe in repair complete all as specified and directed.

Chromium plated toilet paper holder in repair complete all as specified and directed. Make : Jaquar Cat Part No ACN 1153N and equivalent in CERA.

600 mm long brass chromium plated towel rail fancy type in repair complete all as specified and directed. Make : Jaquar Cat Part No ACN-1111NM and equivalent in CERA.

Soap dish in repair complete all as specified and directed. Make : Jaquar Cat Part No ACN 1131N and equivalent in CERA.

PVC (SWR) gully trap 125/110 mm, settting and jointing with solvent cement complete all as specified and as directed.

Dismantling of cast iron or reinforced concrete drain pipe/PVC pipe 100/110 mm dia and below jointed in cement mortar and taking out of floor/walls etc complete all as specified and as directed.

110 mm PVC (SWR) pipes single socket in any lenth with rubber ring joints fixed to wall complete all as specified and as directed.

110 mm PVC (SWR) bends any radius with access door complete all as specified and as directed.

1mm thick wall care putty on wall complete all as specified and as directed

Applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and as directed.

New plaster surface of walls and applying two coat of oil bound distempers over one coat of primer and a coat of 1mm thick wall care putty complete all as specified and as directed.

PVC moulded door frame of size 50x47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, supplying and fixing in opening as per specification and drawing all as specified and as directed.

Factory made solid PVC moulded door shutter with particle board core, 28 to 30mm thick (stiles), with 2, 4 or 6 raised panel design with 2mm thick moulded PVC sheet on the front face & 2mm thick plain colour PVC sheet on back face, fixing in frame at site as per specification & drawing complete all as specified.

150mm long aluminium, anodized, barrel tower bolts of extruded section complete all as specified and as directed.

Butt hinge 100mm size, medium weight, cold rolled mild steel complete all as specified and as directed.

150mm aluminium handles, cast type, anodised complete all as specified and as directed.

4 mm dia galvanised steel wire 50 mm x 50 mm mesh made up in to matresses or cages to water tank etc complete all as specified and as directed.

Water proofing treatment to surfaces of walls/concrete slabs damaged due to moisture and efflorescence including sunken areas of bathrooms/toilets, in balconies by applying acrylic polymer modified cementitious high performance coating or treatment all as per manufacturer's instructions, complete all as specified and as directed. (Make : SmartCare Damp Block 2K/Dr. Fixit

Rendering 5mm thick in cement plaster 1:3 on fair faces of brick work or concrete surfaces as on ceiling complete all as specified.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for complete all as specified and as directed.

75 mm thick PCC 1:4:8, type D-2 by using 40 mm graded stone aggregate as in sub base floor complete all as specified and as directed.

Machine cut Kota stone slab flooring 18-20mm thick over cement screed base 15 mm thick in CM 1:6, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed.

Vitrified tiles (Dura stone heavy duty) of size 300 x 300mm x8-10mm thick as in floors set and jointed in neat cement slurry and pointed in white cement to match the surface 15mm thick screed bed or bedding layer of mortar for laying floor finishes in CM 1:6 complete all as specified and as directed.

S & F in repair 15mm bore bib tap of cast copper alloy fancy type with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified.

S & F in repair 125mm chromium plated shower roses with or without swivel joints, any size, including fixing to steel pipe or union complete all as specified and as directed.

S & F in repair sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long, complete all as specified and as directed.

S & F in repair Vitreous china squatting pan 'Orissa' pattern size 580x440 mm white with integral foot rest including connection to trap and flushing pipe complete all as specified and as directed.

S&F in repairs for Vitreous china wash down water closet Pan (pedestal pattern) white including seat cover complete all as specified and as directed.

S&F in repairs 10 litres capacity PVC low level flushing cistern white inlet float valve, handle complete including brackets complete all as specified and as directed.

M&L for vitreous china urinal half stall type white incl waste pipe fixed in repairs complete all as specified and directed.

S&F in repair concussive push button taps of cast copper alloy, screwed for iron pipe and fixed complete all as specified and as directed.

25mm bore steel tubing galvanized, medium grade with all fittings, laid in floors or fixed to walls, 15mm bore including taking down old pipe complete all as specified and as directed.

PVC (SWR) Floor trap, 75 mm dia of outlet, plain with grating including jointing with solvent cement and making good complete all as specified and as directed.

Cement concrete 1:3:6 type C-2, 75 mm thick using 20mm graded stone aggregates as in plinth protection finished fair and even with using extra cement complete all as specified and as directed.

PCC 1:2:4 type B1 using 12.5mm graded aggregate in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like on drains including formwork complete all as specified and as directed by the Engineer-in-Charge or Garrison Engineer.

Mild steel TMT bars of 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality conforming to IS complete all as specified and as directed.

Preparing old surfaces of wall and applying two coats of weather proof exterior emulsion paint (APEX or equivalent) up to G+3 floor height etc. complete all as specified and directed.

S&F 110 mm PVC (SWR) branch piece, (singal T) equal or unequal with access door complete all as specified and ;as directed

Taking down carefully, copper/ aluminum point wiring (light, fan, socket or power/ LED Light fittings) complete fitting such as switch, sockets, ceiling rose, pendants socket any type, rectangular board terminal boxes etc and making good disturbed surfaces of walls floors and ceiling complete all as directed.Keeping the LED lights in safe custody.

Taking down carefully copper/aluminium sub main wiring of size 2.5/4/6 sqmm from surface/concealed at any height and removing the materials from site and making good the disturbed surfaces of walls,floors roofs etc complete all as specified and directed.

Taking down Old/ Unserviceable MCB DBs TPN / Main Switches by disconnection of electric connection including old unsv MCCBs,MCBs, isolators etc and making good to distrubed surface complete all as specified and directed.

Disconnecting and taking down un serviceable light fittings of any description/ capacity complete all as specified and as directed.

Point wiring for one light/ fan/bell point controlled by one switch using 1.5 Sq mm FRLS copper conductor cables (multistanded) PVC insulated and unseathed in and including PVC concealed conduit as per site requirement (thickness not less than 1.5mm and 20mm dia), medium grade with Modular sunken boxes & PVC back plate for mounting modular type switches, sockets & regulators etc with front plate modular type including supplying and laying PVC insulated unsheathed 1100 volts coppper conductor cable 1.5 Sq mm as earth wire stranded and conected to earth dolly as specified.Note:- Cutting and making same the wall patchs after laying the wire and conduit using putty, white wash and distamper. The surface should be made smooth using putty and should match exactly with the existing wall finish complete all as specified and as directed.

All as per srl item No 102 but for 3 pin 6 Amps socket outlet independent board including PVC insulated PVC unsheathed 1.5 sq mm earth wire and connected to earth dolly complete all as specified and as directed.

All as per srl item No 102 but for 3 pin 6 Amps socket outlet on the same board including PVC insulated PVC unsheathed 1.5 sq mm earth wire and connected to earth dolly complete all as specified and as directed.

All as per Srl item No 102 but for 3 Pin 16 Amps socket outlet independent board with cable 2.5 Sq mm including copper PVC insulated PVC unsheathed 1.5 sq mm earth wire standard and connected to earth dolly complete all as specified and as directed.

S&F for modular switch 6 Amps single pole one way 230 V, 50 Hz, AC , with outer strip complete all as specified and directed by Engr In charge or Garrison Engineer.

S&F for modular switch 16 Amps single pole one way 230 V, 50 Hz, AC , with outer strip complete all as specified and directed by Engr In charge or Garrison Engineer.

S & F modular Bell push flush type 6 amp 230 V, 50 Hz, AC , with outer/inner cover complete all as specified and directed by Engr In charge or Garrison Engineer.

S&F for modular socket 3 Pin 6 Amps flush type 230 V, 50 Hz, AC , with outer/inner cover complete all as specified and directed by Engr In charge or Garrison Engineer.

S&F for modular socket combined 2-in-1, 6 Pin 6 & 16 Amps 230 V, 50 Hz, AC , flush type with outer/inner cover complete all as specified and directed by Engr In charge or Garrison Engineer.

M &L Ceiling rose, surface bakelite 65x 50mm two to three terminals fixed on PVC Round Blockcomplete all as specified and directed by Engr In charge or Garrison Engineer.

S & F calling Bell ding dong 230 volts single pole 50Hz complete all as specified and directed by Engr In charge or Garrison Engineer.

S & F for electronic step type fan regulator 120 watt 230 volts 50 C/S deluxe modular type complete all as spcified and directed.

S&F single pole and neutral enclosure surface mounted 240 voltswith 2 pin and earth plug and socket with one single pole MCB 20 Amps with indicator of make complete all as specified and directed.

S&F in replacement 36W (2 x 2) LED Ceiling/recess light panel for recess mounting warm white colour which provides soft-light and glare free symmetrical illumination complete all as specified and as directed.

Supply and fixing LED lights fitting 1x 20W, 230V,AC decorative box type warm white colour with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type warm white colour with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed.

Supply and fixing LED building security light fitting 30 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp,clamps,suitable bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and as directed.

Supply and fixing LED luminaire 15 watt, 220 V AC recess mounted downlighter type with high efficiency PC diffuser soft light and symmentrical illumination complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cable of suitable size complete all as specified and directed by Engineer-in-Charge or Garrison Engineer.

Supply and fixing LED luminaire 10 watt, 220 V AC recess mounted downlighter type with high efficiency PC diffuser soft light and symmentrical illumination complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cable of suitable size complete all as specified and directed by Engineer-in-Charge or Garrison Engineer.

Supply and fixing Square shape 2X2 feet 34 watt 220 volts AC surface mounted type warm white colour with high efficiency soft light and symmentrical illumination complete with drivers, holders,LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed by Engineer-in-Charge or Garrison Engineer.

S&F of decorative wall mounting 1X9W nickle finish fixture Stylo with frosted glass along with 9W warm white bulb GLS lamp luminaire complete all as specified and directed by Engineer-in-Charge or Garrison Engineer.

S&F Sheet metal enclosure double door type for MCCB TPN DB upto 125 Amps, 4 way vertical type 415 volts with 400 Amps rated busbar and neutral link including chases wall for fixing DB and making good distributed wall surfaces to match with existing specification complete all as specified and directed.

S & F replacement MCCB Three Pole & Neutral capacity of 125 amps 415 volts rupturing capacity 16 KA complete all as specified and as directed.

S&F Sheet metal enclosure double door type for DBs (when MCB to be used) 12 way 240 volts with 200 Amps rated busbar and neutral link including chases wall for fixing DB and making good distributed wall surfaces to match with existing specification complete all as specified and directed.

S&F Sheet metal enclosure MCB distribution board single pole & neutral 240 volts 8 way with IP-43 IK-09 protection double door complete with appropriate size bus bar and neutral link, fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces to match with existing specification complete all as specified and directed.(Note-MCBs will be measured separately)

S & F in replacement MCB single pole 240 volt any rating from 10 to 40 amps "C" series, with rupturing capacity 10 KA ,inculding providing thimble for out going cable complete all as specified and as directed.

S & F in replacement MCB single pole and neutral 240 volt any rating from 63 Amps "C" series, with rupturing capacity 10 KA ,inculding providing thimble for out going cable complete all as specified and as directed.

S&F Sub main wiring with two single core PVC insulated with copper conductor cable stranded of size 6 Sqmm in PVC concealed conduit 25mm dia including PVC insulated copper conductor cable 6 Sq mm as earth lead all as specified. Including taking down old sub main wire complete all as specified and as directed.

S&F Sub main wiring with two single core PVC insulated with copper conductor cable stranded of size 10 Sqmm in PVC concealed conduit 25mm dia including PVC insulated copper conductor cable 6 Sq mm as earth lead all as specified. Including taking down old sub main wire complete all as specified and as directed.

Earthing complete with galvanized steel earth plate electrodes 600 mmx600 mm x6.3 mm thick buried directly in ground earth plate not less than 2.25 m deep below normal ground level with top edge of the plate not less than 1.5 m below normal ground level connected to and including galvanized steel earth lead wire 4.00 mm dia by means of bolts, nuts, check nuts and washers of galvanized iron and steel including PCC pit in PCC 1:2:4 type B-1using 20 mm graded crushed stone aggregate, RCC frame with 40mm thick RCC cover reinforced with 8mm dia deformed bars handle. including excavation and earth work in any type of soil medium grade GI watering pipe 20mm bore with funnel and wire mesh and light grade GI protection pipe 15mm bore main board complete all as shown in electrical plate No 5 connected to main control board all as specified and testing on completion. Note: Excavation earthwork charcoal PCC pit is covered under this item including taking out existing earth plate etc.Note: if earth resistance of earthing is not found (2 to 5 Ω) satisfactory if will be redone by the contractor on his risk and cost.

Taking down ceiling fan/Exhaust fans (C/F of any size/make), cleaning its dust particles oiling,greasing,one coat of synthetic enamel white spray painting with blade ,reassemble the same along with all fittings and hanging the same back to its original position including connecting the wire to ceiling rose etc complete after completing the wiring all as specified and as directed by Engr-in-Charge. Note :- (i) The spares like condensor, ball bearing, cotter pin, nuts & bolts, connecting rods & hooks etc if found defective/damage deemed to be replaced and make the ceiling fans functional. No extra payments will be done on this account.

Material & Laying in trenches or passing through pipe, 1100 volts grade heavy duty cable with "XLPE" insulated aluminium conductor standard served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed of 25 Sqmm x 3.5 core size all as specified including taking down old cable.Note : Earth work and other connected work shall be measured & paid sperately.

M & L Dry sand for sand cushioning to under ground cable 8 cms thick before laying the cable before and 15 cms thick after laying & streching the cable in trenches, including hand punning and consolidating complete as specified. Note : for payment purpose punned thickness shall be measured

M&L Bricks sub class 'B' brick laid dry, flat with width equal to length of brick as cover laid over the cabel to give mechanical protection to underground cabels complete all as specified and as directed.

Supply and fixing GI tubing light grade 40 mm dia along the wall/ in trenches/ in duct / in culvert /road crossing and including provisioning of suitable mild steel flat iron clamps and bolts, nuts and double washers etc for holdining of GI pipe alongwith poles all as specified and directed.

Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300m sweep with, blades, and frame and louvers along with all electrical wire connection all as specified and direceted by Engr-in-charge or Garrison Engineer.

Supply and fixing high speed star rated , ceiling fan 1200mm sweep 230 volt AC single phase with all fixing accessories including providing the suitable size of fan hook in the ceiling as per site requirement complete with all suitable electrical point wiring connection as specified and direceted by Engr-in-charge or Garrison Engineer.

M/S ASHOK KUMAR PACHIALA

s l sharma and sons

M/s LAL DAYAL CONSTRUCTION CO

VIRINDER SINGH

RAMAN CONSTRUCTION CO

BHAGWATI TRADERS

RAJ MOHD

M/S SHREE RAM DUBEY AND SONS