THE CONSTRUCTION OF BLOCK DEVELOPMENT OFFICE AT DHARAMPUR SOLAN

Amount

Cutting in earth work and disposal of excavated earth upto a lead of 20 metres:-

Excavation in foundations, trenches etc., in earth work, lift upto 1.50 Metres stacking the eacavated soil not more than 3 metres clear from the edge of the excavation and then returning the stacked soil in 15cm. layers, when required in to plinths sides of foundations etc., consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated earth as directed with in a lead of 20 metres.

Excavation in drains and channels etc. in earth work including dressing of side and bed and disposing of excavated earth upto a lead of 20 metres and lift upto 1.50 metres disposed earth to be levelled and neatly dressed:

Filling in plinth with sand under floors including watering, ramming, consolidating and dressing complete.

Providing form work with steel plates 3.15mm.thick welded with angle iron in frame 30x30x5mm. so as to give a fair finish including centring, shuutering, strutting and propping etc. with wooden battens and ballies, height of propping and centring below supporting floor to ceiling not exceeding 4 Mtrs. and removal of the same for insitu-reinforced concrete & plain concrete work in:

Foundation, footings basis of columns etc. and mass concrete.

Flat surfaces such as soffits of suspended floors, roofs, landings and the like.

Columns, pillars, posts and struts Square, rectangular or polygonal in plan.

Stair cases with sloping or stepped soffits excluding landing.

Beams, cantilever, girders and lintels.Sides and soffits of beams, beam haunchings, cantilevers, bressumers and lintels not exceeding 1 Mtr. in depth in all heights from floor.

Edges of slabs and breaks in floors and walls:Under 20 cm. wide.

Providing and laying cement concrete 1:4:8 (1 cement:4 sand:8 graded stone aggregate 40mm nominal size) and curing complete excluding cost of form work in:

Providing and laying damp proof course 38mm thick with cement concrete 1:2:4 (1 cement:2 sand:4 stone aggregate 12.5mm nominal size) and curing complete.

Providing and laying cement concrete 1:1.5:3 (1 cement :1.5: Sand : 3 graded stone aggregate 20 mm nominal size and curing complete excluding cost of form work.

Foundations,footings bases of columns and the like and mass concrete.

Suspended Floor roofs, landing and shelves and their support balconies,beams,girders,bressumers and cantilever upto floor two level

Columns, pillars posts and struts upto floor two level.

Stair cases (except spiral stair cases) excluding landing but including preparing of the surface and finishing of nosing upto floor two level.

Providing mild steel/Tor steel reinforcement for R.C.C. work including bending, binding and placing in position complete upto floor two level :Tor Steel :

Providing throating or plaster drip and moulding to R.C.C. chajja.

Brick work using common burnt clay building bricks in foundation and plinth in :-Cement Mortar 1:6 (1 Cement : 6 Sand) second Class Bricks

Half brick masonry in common burnt clay building bricks in :-Cement Mortar 1:4 (1 cement : 4 sand) Second Class Bricks

Stone work for wall lining etc.(Veneer work) 40mm thick, in cement mortar 1:3 (1 cement : 3 sand) including pointing in white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade :

Red sand stone :

White sand stone :

Providing woodwork in frames of doors,windows,clerestory,windows and other frames wrought,framed and fixed in position.Sal Wood

Providing and fixing panelled glazed or panelled and glazed shutters for doors windows and clerestory windows. Including black enamelled iron butt hinges with necessary screws.40mm thick 2nd Class Teak wood.

Extra for superior type of glass used instead of ordinary glass panes in glazed or panelled and clearstory windows.5.5mm thick plate glass.

Providing and fixing flush door shutters decorative type core of block board construction with frames of first class hard wood and well matched first class indian teak plyveneering with vertical grains or cross bends and face veneering on both faces of shutter.40mm thick including black enamelled M.S. butt hinges.

Providing and fixing wire gauge shutters using galvanised M.S. wire gauge of I.S. gauge designation 85 G. with wire of dia 0.56 mm for doors windows and clerestorey windows including bright finished black enamelled iron hinges with necessary screws.40 mm thick 2nd classTeak wood.

Providing eaves board 100mm x25mm. thick including fixing in position.2nd class deodar wood.

Providing and fixing plain square edged cover fillets (beading) 40mmx12mm section with wood screws in ceiling and lining including mitring at junctions.1st class indian Teak wood.

Providing and fixing plain square edged cover fillets (beading) 60mmx12mm section with wood screws in ceiling and lining including mitring at junctions.1st class indian teak wood.

Providing and fixing M.S. grills of required patterns in wooden frames of windows etc. with M.S. Flats, square or round bars with round headed bolts and nuts or by screws.Ornamental Grill.

Providing and fixing fly proof galvanised M.S. wire gauge of IS gauge designation 85 g with wire of dia 0.56 mm to windows and clerestory windows including 60x20 mm beading of.2nd class indian teak wood.

Providing 40x3 mm flat iron hold fast 40cm. Long including fixing to frame with 10mm diameter bolts & nuts and wooden plugs and embeding in cement concrete block 30x10x15cm. 1:3:6 ( 1 cement : 3 sand: 6 graded stone aggregate 20mm nominal size)

Providing and fixing bright finished brass sliding door-bolts with nuts and screws etc. complete.300x15 mm

Providing fixing bright finished brass tower bolts (barrel type) with screws etc. complete.

Providing and fixing bright finished brass handles with screws etc. complete.125mm

Providing and fixing bright finished brass 100mm. Mortice latch and lock and a pair of levers, handles with necessary screws etc. complete (indian make of approved quality)

Providing and fixing 100mm bright finished brass floor door stopper with rubber cushion screws etc. to suit shutter thickness complete

Providing and fixing bright finished hard drawn hooks and eyes.250 mm

Providing and laying granite stone in flooring 20mm(average)thickness base of cement mortar 1:3(1cement: 3 sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of granite stone i/c rubbing and polishing complete. 20mm.thick

White glazed tiles 6 mm thick in flooring, treads of steps and landing laid on a bed of 12 mm thick cement mortar 1:3(1 cement :3 sand) finished with flush pointing in white cement.

Providing and fixing 10mm thick anti skid water proof stain and impect resistent heavy duty vetrified tiles Nitco or equivalant 600x600mmx10mm manufactured of approved shade and colour in flooring, treads of steps and landings laid over 12mm thick cement mortar 1:3 (1 cement : 3 sand) jointed with cement slurry mixed with pigment to match the shade of tiles as required complete.

Providing and laying heavy duty precast cement conrete inter locking paver blocks vibro compacted upto M- 50 grade i/c border or kurb block grey or coloured over sub-base of concrete with 25mm thick average thickness of cement mortar 1:4 (1 cement : 4 sand) laid over and jointed with neat cement slurry mixed with pigment to match the shade of blocks i/c curing rubbing & polishing complete (Sub base concrete floor to be paid for 80mm thick inter locking blocks

Providing and fixing 15 cm. wide 45 cm. overall semicircular plain G.I. sheetgutter with ironbrackets 40x3mm size bolts and nuts and washers etc. including making necessary conections with rain water pipe complete as per design. 0.80 mm Thick

Providing and fixing 0.60mm thick prepainted steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP) organic coating of 20 microns over 5 microns primer coating to back coat of polyster of 5 microns over 5 microns primer coating i/c fixing with prepainted iron J or L hooks, bolts and nuts 6mm dia metre with prepainted limpet and rubber washers complete with all accesoriees as required as per the direction of Engineer-in-charge.

Providing and fixing ridges or hips 60 cm overall with 0.60mm thick prepainted steel sheets in roofing with hot dipped metalic zinc coated sheets with top coat of regular modified polyster organic coating of 20 microns over 5 microns primer coating + back coat of polyster of 5 microns over 5 microns primer coating i/c fixing with prepainted iron J or L hooks, bolts & nuts 6mm dia & prepainted G.I. limpet and bitumen washers complete with all accessories as required as per the direction of Engineer in Charges.

Providing and fixing valley 60 cm overall 0.60mm thick prepainted steel sheet in roofing with hot dipped metalic zinc coated sheet with top coat of regular modified polyster organic coating of back coat of polyster of 5 microns over 5 microns primer coating i/c fixing with prepainted iron J or L hooks, bolts and nuts 6mm dia with prepainted G.I. limpet and bitumen washers complete with all accessories as required as per the direction of Engineer-in-charge.

Providing and fixing flushing 38cm overall with 0.60mm thick prepainted sheet in roofing with hot dipped metalic zinc coated sheet with top coat of regular modified polyster organic coating of 20 microns over 5 microns primer coating + back coat of polyster of 5 microns over 5 microns primer coating i/c fixing with prepainted iron J or L hooks, bolts and nuts 6mm dia meter & prepainted G.I. limpet & bitumen washers complete with all accessories as required as per the direction of Engineer-in-Charge.

Providing and fixing a P.G.I. sheet bend of required degree (0.63mm thick sheet)for rain water pipe 100 mm dia

Providing and fixing on wall face PVC (D-Plast) rain water pipes of working pressure not less than 4.5 kg/sqm including filling the joints with approved adhesive complete.100mm dia pipes

Providing and fixing on wall faces PVC (D-Plast) accessories for rain water pipes including filling the joints with approved adhesive complete PVC Plain bend 100mm dia

Steel work rivetted in built up sections including cutting,hoisting, fixing,in position and applying a priming coat of red lead paint .In trusses and trussed purlins in buildings

Applying priming coat over new steel & other metal surfaces after & including preparing the surface by thoroughly cleaning oil grease dirt and other foreign matter and scoured with wire brushes fine steel wool scrapers and sand paper complete.With ready mixed priming paint brushing red lead,Red-oxide/zinc oxide chrome.

Painting two costs (excluding priming cost on new steel and other metal surfaces eith enamel paint brushin to give an even shade including cleaning the surface of all dirt,dust and other foregin matters :--Enamel paint other than white :--

Applying spirit or oil stains (any colour)on wood and wood based surfaces to given an even surfaces including cleaning the surfaces of all dirt,dust and sand papering so as to produce a smooth dry and matt surface including stopping & knotting.

Polishing two coats with french polish on new wood and wood based surfaces to give an even surface including cleaning the surface of all dirt,dust,and sand papered smooth and including a coat of wood filler.

Applying Birla white wall care putty over plaster surface after thoroughly brushing the surface free from mortar drops, dust, loose materials and other foreign matters sand papered smooth to give final matter finish to the surface complete.Birla White Putty for the internal 9" walls

Finishing wall with weather proof exterior grade emulsion of approved design (Apexultima) or its equarlied on undecorated wall surfaces (two coats) to give an even shade and final finish after throughly cleaning the surface to remove all dirt, dust and other foreign matter etc including sand paper smooth complete.

Wall painting (two coats) with acrylic emulsion paint of approved brand and manufacture for interior grade on undecorated concrete/stone/plastered wall surfaces to give an even shade including thoroughly brushing the surface free from mortar dropping and other foreign matter and sand papered smooth including applying of putty a required for melting the surface.

6mm Cement plaster to ceiling (a) In Cement mortar 1:3 (1Cement:3 Sand)

10mm cement plaster in single coat on fair side of brick/concrete walls for internal plastering upto floor two level including arrises, internal rounded angles,chamfers and/or rounded angles not exceeding 80mm in girth and finished even and smooth. (iii) Cement mortar 1:5 (1 cement:5 sand)

15mm Cement plaster in single coat on the rough side of brick/ concrete/stone walls for interior plastering upto floor two level including arrises,internal rounded angles,chamfers and/or rounded angles not exceeding 80mm in girth and finished even and smooth. (iii) Cement Mortar 1:5 (1Cement:5 Sand).

Providing plinth protection 50mm thick in cement concrete 1:3:6 (1 Cement : 3 Sand : 6 Graded stone aggregated 20mm nominal size)

Providing under layer for plinth protection of 75mm thick (unconsolidated) bed dry brick/stone aggregated 40mm nominal size with rammed and consolidated and grouted with fine sand including preparation of ground.

Providing and fixing to wall ceiling and floor galvanised mild steel tubes (Medium grade) tube fitting and clamps including making good the wall, ceiling and floor:- 15mm nominal bore

15mm nominal bore

20mm nominal bore

25mm nominal bore

Providing and laying in trenches, galvanised mild steel tubes (heavy grade), tube fittings (earth work in trenches to be measured and paid separately) :- 32mm nominal bore

32mm nominal bore

40mm nominal bore

Fixing water meter stop-cock in galvanised mild steel tube including necessary fittings such as mild steel galvanised jam nut, sockets, etc. cutting and making long screws complete (water metre and stop-cock to be measured and paid for separately)

Construction chamber 300mm x 300mmx500mm inside size for stop cock with C.I. surface box 100mm x 100 mm x 75mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement : 2 sand 4 graded stone aggregate 20mm nominal size) 75mm thick foundation concrete 1:5:10 ( 1cement : 5 sand : 10 grades stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement :3 sand) finished with a floating coat of neat cement including curing complete :-with 100 mm thick walls of brick masonry in cement mortar 1:5 (1 cement: 5 sand)

Providing and fixing vitreous China wash down, water closet (European type. W.C. pan) with integral 'P' or 'S' trap including jointing the trap with soil pipe in cement mortar 1:1(1 cement : 1 sand) (Seat and over to be measured and paid for separately):-

Providing and fixing to wall ceiling and floor vitreous China low level flushing cistern with a pair of C.I. or mild steel brackets, complete with fitting such as lead valve less syphon, 15mm nominal size brass ball valve with polythene float, C.P. Brass handle, unions and couplings for connections with inlet, outlet and overflow pipes, 40mm dia C.P. flush bend including cutting holes in walls and making good the same and connecting the flush bend with cistern and closet (overflow pipe to be measured and paid for separately).

Providing and fixing plastic seat (Solid / Hollow type) and cover for wash down water closet with C.P. Brass hinges and rubber buffers :

Providing and fixing vitreous China bowl pattern urinal including connection the urinal with waste pipe by means of white lead mixed with chopped hemp (waste pipe to be measured and paid for separately. :Flat back type of size 430mm x 260mm x 350mm.

Providing and fixing to wall ceiling and floor with a pair of C.I. Or M.S. brackets complete with fittings including C.I. Syphonic apparatus, mosquito proof lid, C.P. Brass unions and coupling for connections with inlet, outlet and overflow pipes including cutting holes and making good the same (overflow pipe to be measured and paid for separately) :-

Providing and fixing C.P. brass flush pipe / spreaders for urinal with fitting such as unions, clamps etc. (all in C.P. Brass) including cutting holes and making good the same :-

Providing and fixing vitreous China wash basin with single hole for pillar tap with C.I. or M.S. brackets painted white including cutting holes and making good the same but excluding fittings:-

Providing and fixing kitchen sink with C.I. Or M.S brackets, painted white including cutting holes in walls and making good the same but excluding fittings :-600mm x 450 x 250 mm Vitreous China :

Providing and fixing C.P. Bottle Trap for wash basin and sink :-40mm dia

Providing and fixing 600mm x 450 mm bevelled edge mirror of superior glass mounted on 6mm thick A.C. Sheet or plywood sheet and fixed to wooden plugs with C.P. Brass screws and washers.

Providing and fixing C.P. Brass Towel rail complete with C.P. Brass brackets fixed to wooden plugs with C.P. Brass screws :-750mm x 20mmm

(i)Providing and fixing 600mm x 120 mm glass shelf with C.P. Brass bracket and guard rail complete, fixed to wooden plugs with C.P. Brass screws.

Providing and fixing toilet paper holder:-

Providing and fixing liquid soap container with C.P. Brass lid and brackets fixed to wooden plugs with C.P. Brass screws :-

Providing and fixing chromium plated brass soap dish with C.P. Brass brackets fixed towooden cleats with C.P. Brass screws :-

Providing and fixing C.P. Brass shower rose with 15mm or 20mm inlet :-

Providing and fixing Division Plate for Urinals 600mm x 300. Vitreous China

Providing and fixingC.P. Brass Bib tap with Cpastan Head

Providing and fixing Brass stop cocks :15mm dia

15mm dia

20mm dia

25mm dia

32mm dia

40mm dia

Providing and fixing C.P. brass angle valve 15mm without Nuts and pipe.

Providing and fixing 15mm mixer for kitchen sink with top / bottom swinging spout.

Providing and fixing one hole basin mixing Faucet.With the Wash basin for the hot and cold water supply

Providing and fixing P.V.C connection with brass unions :-300/450mm length :-15mm nominal bore

Providing and fixing brass ball valve (horizontal plunger type)-:High pressure with polythene plastic floats :-25mm nominal bore

Providing and fixing ferrule including boring and taping the main :32mm nominal bore

Providing and fixing PVC water storage tank of ISI : 12701 marked, G.I. inlet and outlet connection, 15mm nominal bore ball valve and mosquito proof PVC cover with locking arrangement including hoisting up to all heights above ground level :- 1000 litres net capacity tank

Providing and and fixing PVC floor trap ISI marked of self cleaning design including fixing with approved adhesive, cost of cutting and making good the wall and floors etc. complete 110 mm X 90 mm.

Providing and fixing high pressure PVC spigot and socket, waste and ventilating pipes ISI marked including fixing with approved adhesive etc. complete.

150mm dia

100mm dia

75mm dia

Providing and fixing PVC single equal branch plain ISI marked including fixing with approved adhesive etc. complete.150mm dia

100mm dia

75mm dia

Providing and fixing PVC collars ISI marked including fixing with approved adhesive etc. complete.150mm dia

100mm dia

75mm dia

Providing and fixing PVC plain bend ISI marked including fixing with approved adhesive etc. complete. 150mm dia

100mm dia

75mm dia

Providing and fixing PVC plain double equal branch ISI marked including fixing with approved adhesive etc. complete. 150mm dia

100mm dia

75mm dia

Providing and fixing PVC clamps ISI marked of approved design with steel screws and rawal plugs etc. complete. 150mm dia

100mm dia

75mm dia

Providing and fixing PVC reducer ISI marked including jointing with approved adhesive etc. complete.110 mm X 75 mm dia.

Providing and fixing stainless steel kitchen sink of approved standard ISI make with drain board and C.P. waste with C.I. or M.S. Brackets painted white including cutting holes and making good the same but excluding fitting.610 x 510 mm with bowl depth 200 mm.

Constructing brick masonry chamber for underground C.I. Inspection chamber and bends with common burnt clay building bricks in cement mortar 1:5 (1 cement : 5 sand ) C.I. Cover with frame (light duty ) 355mm x 610mm internal dimensions total weight of cover with frame to be not less than 38kg (weight of cover 23 kg. and weight of frame 15kg) R..C.C top slab with 1:2:4 mix (1 cement : 2 sand : 4 graded stone aggregate 20mm nominal size ) foundation concrete 1:5:10 ( 1cement : 5 sand : 10 graded stone aggregate 40mm nominal size) inside plaster 15mm thick with cement mortar 1:3 (1 cement : 3 sand) finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete.

Inside dimensions 455 mm x 610 mm x 450 mm deep single pipe line.

Inside dimensions 500 mm x 700 mm x 450mm deep for pipe line with one or two inlets.

Inside dimensions 600 mm x 850 mm x 450 mm deep for pipe line with three or more inlets.

Providing and fixing PVC single equal branch with ovel access door, ISI marked insertion rubber washer 3 MM thick bolts and nuts complete including fixing with approved adhesive etc. Complete .

110 MM (one hundred ten millimeter Dia )

75 MM (Seventy five millimeters Dia )

providing and fixing PVC door band with oval access door insertion rubber washer 3 MM thick bolts and nuts ISI marked complete including fixing with approved adhesive etc. complete

110 MM (one hundred ten millimeter Dia )

75 MM (Seventy five millimeters Dia )

Providing and fixing PVC collars ISI marked including fixing with approved adhesive etc. complete.

75 MM (Seventy five millimeters Dia )

110 MM (one hundred ten millimeter Dia )

Providing and fixing PVC Plain bend ISI marked including fixing with approved adhesive etc. complete

75 MM (Seventy five millimeters Dia )

110 MM (one hundred ten millimeter Dia )

Constructing brick masonary chamber for under ground C.I inspection chamber and bends with common burnt clay building bricks in cement mortar 1:5 (one cement: five sand)C.I cover and frame( light duty) 355x610mm internal dimension total weight with cover and frame to be not less than 38kg (weight of cover 23kg and weight of frame 15kg ) RCC top slab with 1:2:4 mix (one cement: two sand: four graded stone aggregate 20mm nominal size) 1:5:10 (one cement : five sand: the graded stone aggregate 40mm nominal size ) and inside plastering with cement mortar 1:3(one cement: three sand) finished with a floating coat of neat cementon wallsand bed concrete etc complete including curing complete. including carriage of material upto all leads and lifts in all floor

Inside dimensions 455mm x610mm x450mm deep for single pipe line

Inside dimensions 600mm x850mm x450mm deep for pipe line with three or more inlets

Providing and fixing white vitrous china flat back or wall corner type lipped front urinal basin of 430x260x350mm and 340x430x265mm sizes respectively with automatic flushing cistern with fittings R.S. or C.I. brackets standered size galvanised steel flush pipe and spreaders galvanised steel flush pipe and spreaders with brass unions and G.I clamp complete including painting of cistern and fitting cutting and making good the walls and floors where required . One urinal basin with 5 litre automatic flushing cistern .

Providing and laying brick bats 50mm size including carriage of material with all leads and lifts and other incidentals

Providing and laying C.I manhole cover 50cm dia including carriage of material with all leads and lifts and other incidentals

Providing and laying 200mm cast iron rungs with chequred or ribited non soli surface including and fixing in main holes with 200x200x200mm cement concrete 1:3:6 stone of 20mm nominal size including carriage of material with all leads and lifts and other incidentals

Vicky Kumar

KUSHLA NAND SHARMA

SUNIL THAKUR