White Washing of XEN Office Canal Colony

Amount

Dismantling Brick Work, Tile Masonry or Tile Lining and Tile Terracing in cement as per HSR Item NO. 8.5 b

Scraping cement plaster as per HSR Item No. 8.32 ( c )

Scraping white wash and colour wash as per HSR Item No. 8.32 a

First class brick work laid in cement sand mortar 1:5 in first storey upto 4 metres above plinth level. As per HSR Item No. 11.8

10 mm thick cement plaster 1:4 complete as per HSR Item No. 15.5

Preparation of plastered surfaces for oil bound distemper including sand papering the surface, applying one coat of linseed oil. and filling with approved quality filler consisting of white lead, linseed oil, varnish and chalk mitti including finishing the surface to the required finish complete as per HSR Item No 16.24

Distempering with washable oil bound distemper (of approved manufacture) two coats on old distempered work As per HSR Item No. 16.60

Providing two coats of exterior acrylic emulsion paint As per HSR Item No. 16.79 (b)

Dismantling white or coloured glazed tiles (to be carefully removed) As per HSR Item No. 8.38

Pressed steel sheet frames (chowkats) consisting of 2 mm thick steel sheet of the specified section, including iron lugs (hold fasts) iron hinges, conforming to RW.D. specifications, including bolts for fixing stops, locknotch, provision for receiving tower bolts, and finished with one coat of readymixed paint red lead non-setting primer, of approved quality, fixed in position including the cost of cement concrete 1:3:6 for filling in the frame, and cement concrete 1:3:6 for lugs complete. Door and window frame of size 76 mm x 38 mm with 35 mm wide single rebate. as per HSR Item No. 18.34 (B)

Commercial hard wood such as hollock, champ, chikrassy and chaplash (kiln-seasoed) shutters with vertical styles and rails as specified in statement No.1 (attached in the end of chapter) with 2 Nos. panels made out of three layers, flat pressed teak wood particle board both sides commercial veneered with phenol formaldehyde/synthetic resins of the specified thickness mentioned below tounged and grooved including cost of iron hinges fixed in position excluding the cost of tower bolts and handles but including labour for fixing the same, (with 12mm thick teak wood particle board commercial as panels as per HSR Item No. 17.30 (B) a

Wire gauze commercial hard wood such as hollock, champ, chikrassy etc. (non-coniferous timber other than teak conforming to I.S. specification No. 1003 kiln seasoned) door and window shutters without springs housed in chowkats including chocks, iron hinges and screws, etc., complete fixed in position (excluding the cost of tower bolts, and handles but including the labour for fixing the same 30 mm thick asc per HSR Item No. 17.31 (A)

Scraping, brushing to remove paint to bare metal surface.As per HSR Item No. 16.65

Painting two coats with ready mixed paint for metallic surfaces in all shades on old steel or iron work complete as per HSR Item No. 16.18

Applying pink primer or aluminium priming coat on wood work including preparation of surface, knotting and stopping etc. As per HSR Item no. 16.2

Painting two coats excluding priming coat with ready mixed paint in all shades on new wood work. complete as per HSR Item No. 16.4

Painting two coats with ready mixed paint in all shades on old wood work to give an even shade including rubbing down old paint. Complete as per HSR Item No. 16.6

Cup board shutter of commercial hard wood such as hollock, champ, chikrassy, chaplash etc., (non coniferous timber other than teak conforming to IS. specification no. 1003 kiln seasoned) excluding chowkat but with commercial plywood panels or faced on one side including iron hinges and screws fixed in position (excluding the cost of handles, tower bolts, hasp with stample, but including the labour for fixing the same)As per HSR Item no. 17.32 (a)

Cost of iron fittings, complete for doors and windows, such as tower bolts, handles etc. and screws for these fittings (excluding sliding bolts)(a) for single leaf shutter as per HSR Item No. 17.71 (a)

Supply and erection of pipe of 1.60 mm thickness recessed in wall and complete with M.S. boxes for housing regulators wall sockets switches etc. as per HSR Item 31.4

(i) Fan Point (b) Medium

(ii) Light Point (a) Short

(b) Medium

(c) Long

(vi) Call Bell (b) Medium

(vii) 3 Pin 5 Amp plug (a) Short

Wiring only in 1.5 sqmm PVC insulated copper conductor cable in existing conduit pipe and MS boxes covered with 5mm thick bakelite sheet including cost of switch, wall socket, ceiling rose etc. as per HSR item no. 31.38

(i) Fan Point (b) Medium

(ii) Light Point (a) Short

(b) Medium

(c) Long

(vi) Call Bell (b) Medium

(vii) 3 Pin 5 Amp plug (a) Short

(viii) 3 Pin 5 Amp plug (a) Short

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE (as approved by the Engineer-in-charge) EUROPEAN TYPE WATER CLOSET SUITE, SYPHONICTYPE consisting (a) Single trap syphonic W.C. Suite (ii) White colour as per HSR Item no. 30.5 A (i)

Providing and fixing in position best Indian make (ordinary) lavatory suites consisting of Lavatory in vitreous chinaware size as given below (to the approval of the Engineer-in-charge) including China plug for tap hole where necessary Single Colour As per HSR Item No. 30.41 (v)

Providing and fixing in position best Indian make Pedestal fittings of vitreous chinaware complete (as required by the Engineer-in-charge) as per HSR Item No. 30.44 (ii)

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE SHOWER CP. BRASS ROSE-SHOWERS 125 mm i/d as per HSR Item No. 30.66 B (ii)

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE TOWEL RAILS FIXED in with rawls lugs embedded in walls with CP. brass screws, complete in all respect INCLUDING CUTTING AND MAKING GOODS THE WALLS ETC as per HSR Item No. 30.68 (D)

Providing and fixing in position best Indian make soap dish fixed into wall with C.P. brass screws and complete in all respects including cutting and making goods the walls etc as per HSR Item No. 30.70 (a) (i)

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE BEVELLED EDGE 5.5 MM THICK MIRROR mounted On ASBESTOS Sheet GROUND FIXED IN POSITION BY MEANS OF 4 NOS. CHROMIUM PLATED BRASS SCREWS AND WASHERS over rubber washers and rawl plug embeded in the wall or chromium plated brass clamps with C.P. brass screws (as required by the Engineer-in-charge) COMPLETE INCLUDING CUTTING AND MAKING GOOD THE WALLS ETC. INDIAN MAKEas per HSR Item No. 30.71 A (i) 600x450mm

Providing and fixing in position 15 mm i/d C.P. brass bib cocks of best quality (as required by the Engineer-in-charge). As per HSR Item NO. 30.75 ( c )

Providing and fixing in position C.P. brass stop cocks (as approved by the Engineer-in-charge). As per HSR Item No. 30.76 A (i)

Providing and fixing 15 mm C.P. brass laboratory cock swan neck of best quality (to the approval of Engineer-in-charge as per HSR Item NO. 30.78 A

Providing and fixing 1st quality ceramic glazed wall tiles confirming to I.S. 15622 (thickness to be specified by the manufacturer) of approved make in all colors, shades except burgundy, bottle green, black of any size as approved by Engineer-ln-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 coarse and jointed with grey cement slurry, including pointing in white cement mixed with pigment of matching shades complete. (a) Size of ceramic Glazed tiles 200mm x 300mm as per HSR Item NO. 14.92 (a)

Providing & fixing PVC Rain water pipe 6 Kg Pressure of ISI mark in cement mortar during masonry work. As per HSR Item No. 13.89

(a) 100 mm dia PVC pipe 6 kg pressure

Providing & fixing PVC Bend ISI Mark As per HSR Item No. 13.90

(a) 100 mm dia PVC Bend

Supply of CPVC Pipes (NS Item)

(b) 20 mm i/d

(c) 25 mm i/d

Supply of CPVC TEE Bends & Sockets (NS Item)

(b) 20 mm i/d

(c) 25 mm i/d

LABOUR FOR LAYING, JOINTING, FIXING AND TESTING G.I./ P.V.C/W.I. PIPE LINES AND SPECIALS tees bends, sockets, elbows etc. INSIDE BUILDING and testing etc., complete including cutting threading.As per HSR Item No. 28.18 B

(b) 20 mm i/d

(c) 25 mm i/d

Pvdg. & fixing ceramic tiles/anti skid tiles of size 400mm x 400mm or above size of approved make in flooring, HSR Item No. 14.91

Cement concrete 1:2:4 with stone aggregate 20 mm nominal size in first storey upto 4 metres above plinth level HSR Item No. 10.61

Removing door and windows (wood and steel) with chowkats by making recesses in walls when the wall is not to be dismantled :- HSR Item No. 8.18 a & b

PROVIDING AN D FIXING IN POSITION BEST INDIAN MAKE A RANG E O F THRE E STALL URINALS 1150 M M HIGH I N VITREOU S CHINAWARE WIT H ON E NO. 1 0 LITRES CAPACITY C I . UTOMATIC FLUSHING CISTERN WIT H FITTINGS AN D FLUS H PIPE COMPLET E as per HSR Item No. 30.31 (i)

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE STALL URINAL IN VITREOUS CHINAWARE (to the approval of the Engineer-in charge) consisting of as per HSR Item no. 30.29 (i)

Providing and laying 80mm thick interlocking paver blocks of all shapes and colours in design mix cement M-35 over a bed of 30mm thick fine sand complete in all respect as per HSR Item no. 10.159

Cement concrete 1:8:16 with brick ballast 40 mm nominal size in foundation and plinth as per HSR Item no. 10.26

Supplying and fixing glass panes with teak wood moulding (c) 4 mm thick (glazing area above 55 sq dm, but upto 84 sq dm of each pane) as per HSR Item no. 17.42 ( c )

D/D credit of dismentled material as per Item No. 1

THE DARSHANA CO OP L/C SOCIETY LTD

M/S JAI BHOLE NATH CO-OP L AND C SOCIETY LTD