PROVISION OF URP BASED TECHNICAL BUILDING AT HEMRL UNDER GE I RND PASHAN PUNE

Amount

Lump sum price worked out by the Contractor for “BUILDING AND STRUCTURES, " as listed in Schedule ‘A’ Part - I

Construction of URP based magazine consisting of two Nos of RCC sheds of size 14m x 14m (Internal) with common RCC wall including Ramp, RCC platform, steel door with all fittings and fixtures complete all as shown on drawings and as specified. Note: Blast wall and Hard standing items as shown on drawing shall be measured and paid separately in relavent schedule.

Construction of static water tank of capacity 225000 litres complete all as shown on drawings and specified.

Lump sum price worked out by the Contractor for “SITE CLEARANCE AND AREA DEVELOPMENT INCLUDING DEMOLITION & EARTHWORK EXCAVATION, " as listed in Schedule ‘A’ Part - II representing __________ % _______________ percent Above / Below the lump sum price of `15,62,758.13 inserted by the MES in Schedule ‘A’ Part - II

Lump sum price worked out by the Contractor for “INTERNAL ELECTRIC SUPPLY (FLAME PROOF WIRING)” as listed in Schedule ‘A’ Part - III representing __________ % ____________ percent Above / Below the lump sum price of `1,80,150.00 inserted by the MES in Schedule ‘A’ Part - III

Lump sum price worked out by the Contractor for “ PATH/ HARDSTANDING ” as listed in Schedule ‘A’ Part - IV representing ________ % ____________ percent Above / Below the lump sum price of ₹33,69,617.43 inserted by the MES in Schedule ‘A’ Part - IV

Lump sum price worked out by the Contractor for “AREA DRAINAGE” as listed in Schedule ‘A’ Part - V representing __________ % _________________ percent Above / Below the lump sum price of ₹4,25,146.67 inserted by the MES in Schedule ‘A’ Part - V

Lump sum price worked out by the Contractor for “BLAST WALL & RETAINING WALL” as listed in Schedule ‘A’ Part - VI representing __________ % _________________ percent Above / Below the lump sum price of ₹34,85,641.27 inserted by the MES in Schedule ‘A’ Part - VI

Lump sum price worked out by the Contractor for “EXTERNAL WATER SUPPLY ” as listed in Schedule ‘A’ Part - VII representing __________ % ____________ percent Above / Below the lump sum price of ₹1,07,169.01 inserted by the MES in Schedule ‘A’ Part - VII

Lump sum price worked out by the Contractor for “EXTERNAL ELECTRIC SUPPLY” as listed in Schedule ‘A’ Part - VIII representing _______ % _________________ percent Above / Below the lump sum price of ₹3,51,675.10 inserted by the MES in Schedule ‘A’ Part - VIII

Lump sum price worked out by the Contractor for “LIGHTENING PROTECTION SYSTEM” as listed in Schedule ‘A’ Part - IX representing _______ % _________________ percent Above / Below the lump sum price of `46,069.80 inserted by the MES in Schedule ‘A’ Part - IX

SITE CLEARANCE AND AREA DEVELOPMENT INCLUDING DEMOLITION & EARTH WORK EXCAVATION Returning, filling in including spreading, leveling, watering and well ramming in layers not exceeding 25cm in soils complete all as specified and directed.

Removing surplus excavated soil to a distance not exceeding 50m depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed.

INTERNAL ELECTRIC SUPPLY Group C wiring for light point/ fan point / exhaust fan point/ call bell point with 1.5 sq.mm FRLSH PVC insulated copper conductor single core cable in surface/recessed steel conduit, FLP termination boxes and earhing the point with 1.5 sq. mm FRLSH PVC insulated copper conductor single core cable etc. complete all as specified and directed. (a) One flameproof light point point controlled by one; single pole switch/ Rotary switch.

S&F & testing PVC insulated, PVC sheathed cable galvanized steel strip or wire armoured, electric control cables (Heavy duty) with stranded copper conductor of size 4.0 sq mm, 4 core, 1100 Volts grade complete all as specified and directed.

S&F flame proof switch socket combination 4P+E (5 Pin) suitable for 32 Amps, 415 volts including plug and top, LM-6 body, certified by CIMFR and PESO , ISI marked complete all as specified and directed.

S&F Flame proof / Weatherproof LED Well Glass Light Fitting for 90 Watt with lumen out put not less than 9000 Lumens, body made out of aluminium alloy LM -6 body epoxy painted with wire guard relfector, flameproof Heat Resistant Clear Toughened ‘Type‐ A’ with LED COB / SMD (Bridge, Cree, Citizen) including suitable electronic including necessary fixing arrangments and connecting up complete all as specified and directed.

S&F Flame proof / Weatherproof LED Well Glass Light Fitting suitable for 30 Watt with lumen out put not less than 3000 Lumens, body made out of aluminium alloy LM -6 body epoxy painted with wire guard relfector, flameproof Heat Resistant Clear Toughened ‘Type‐ A’ with LED COB / SMD (Bridge, Cree, Citizen) including suitable electronic including necessary fixing arrangments and connecting up complete all as specified and directed.

S&F flame proof panel board made out LM6 material and high stainless steel hignges and nuts Incomer 63 AMPS 18KA 4P MCCB and out going 6 Amps MCB SP 10 KA - 4 Nos , 32 Amps MCB TP 10 KA - 2 Nos complete all as Gas Gr IIA, IIB certified by CIMFR Dhanbad & CCOE (PESO) Nagpur along with ISI marking complete all as specified and directed.

S&F flame proof Double compression Brass gland Chromium plated of 3/4 inch size (18.1 to 20 mm) complete all as specified and directed.

S&F flame proof Double compression Brass gland Chromium plated of 1 inch size (23.1 to 26 mm) complete all as specified and directed.

S&F flame proof Double compression Brass gland Chromium plated of 1-1/2 inch size (33.1 to 37 mm) complete all as specified and directed.

M&L for special factory made earthing electrode comprising of hot dpped galvaized MS flat inserted in to GI pipe of 88mm bore (outer), 3m length, filled with non magnetic anti corrosive material specially developed for ground resistance enhancement power around the electrode to retain moisture conforming to IS 3043 including necessary boring in ground of 200mm dia in any type of strata connecting to test point, the earth resistance shall be less than 3 ohms including provision of FRP earth pit cover complete all as specified and directed. Contractor shall improve the earthing resistance within the permissible limit without any extra cost. "MAKE: Fast Electrode / ASHLOK/ ITorrent/ U-Protec.

Note: (i) GI earthing pipe should have successfully tested for salt spray test (corrosion test) Certificate for minimum 500 hours. The Earthing Electrode should have a GTP & Drawing approval from MSEDCL infra Project. The Earthing Electrode should be tested in MSME. Any one such Earthing Electrode should have successfully type test certification by CPRI (Central Power Research Institute, Govt of India) for the Short Time current at 43 kA rms for 1 Sec; with initial peak of 90.12 kA. The rated voltage for testing in CPRI should be 400 V at rated current of 10kA. The Earth Enhancing Compound should have Test certification from NABL accredited Lab. It should be tested as per IS 1350 / AHPA guideline’s. The pH value of Compound should be 7.59, Moisture % by mass should be 8.91 & Solubility in 1:1 HCL should be 32.29 %. The Compound should be tested ELV Test as per protocol IEC 62321/111/54/CDV/ICP-OES for contain of Lead (23.0 ppm), Cadmium (15.0ppm), Mercury (Below Detection Level) & Hexa-chromium (Below Detection Level). (ii) (ii) Rate for FRP earthing pit cover shall be deemed to be included in rate quoted

Supply and fixing FAST Electrode earthing with Pure Copper Single Pipe, the pipe dia is of 76 mm Pipe & wall thickness of pipe is 2.0 mm & the cavity is filled with highly conductive, non- corrosive material along with Supply of Earth Enhancing Compound 2 Bag of 25 Kgs including necessary boring in ground of 200mm dia in any type of strata connecting to test point. The Earth Enhancing Compound should have Test certification from NABL accredited Lab. It should be tested as per IS 1350/ AHPA guideline’s. The pH value of Compound should be 7.59, Moisture % by mass should be 8.91 & Solubility in 1:1 HCL should be 32.29 %. The Compound should have test certification ELV Test as per protocol IEC 62321/111/54/CDV/ICP -OES for contains of Lead (23.0 ppm), Cadmium (15.0ppm), Mercury (Below Detection Level) & Hexa-chromium(Below Detection Level). The manufacture of Earthing should be registered under Udyam registration and certified for ISO 9001:2015

Note for item No 21 & 22 (i) Earth resistance should be less than 1 ohms. If the desired result of the earth resistance not comes under 01 ohms the contractor should fill extra earth compound with out extra payment to the Govt. (ii) Rate for FRP earthing pit cover shall be deemed to be included in rate quoted

M&L for epoxy base insulator of suitable size, 35mm height fixed on PCC blocks / wall / MS angle / Pipe / channel/ on towers / on Galvalume sheet with and including bolt size 8 mm dia, 19 mm length, nuts and washers etc complete all as specified and directed

S&F indicator for electrostatic discharge(ESD) earthing made out of 300x300x3 mm MS sheet fixed on and including 25x25x3 mm angle iron post 1 metre length with PCC 1:2:4 type B1 foundation block of size 200mm x 200mm x 300 mm height using 20 mm graded stone aggregate derived from natural sources and painting exposed surface with two coats of syenthetic enamel paint over coat of red oxide primer and writing letters for indication of ESD earthing complete all as specified and directed.

S&F fixing copper plate 150x150x3mm thick with 1 No. round soild copper bar 20 mm dia & 150 mm long brazed or threaded & fixed in the centre of the plate for manual electrostatic discharge & fixed on existing wall at height of 1.5 mtr complete all as specified and directed

S&F copper plate 600x600x3 mm thick fixed to floor by means of brass nuts/bolts and duly connected to ESDS system complete all as specified and directed.

EXTERNAL WATER SUPPLY Cutting Bituminous road and making good the same including supply of extra quantities of materials i.e. aggregate, moorum screening, red bajri and labour required complete all as specified and directed.

M&L for constructing masonry Chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve,with C.I. surface box 100mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size ) , i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete all as specified and directed.

EXTERNAL ELECTRIC SUPPLY S&F, testing, commissioning of LT UG cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 50 sq mm 3.5 core complete all as specified and directed.

S&F testing, commissioning of LT UG cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 10 sq mm 4 core complete all as specified and directed. Note. Earth work excavation, sand cushioning, cable covers will be measured and paid separately.

(a) Incoming MCCB 4 pole 415V, 63 Amps, 50Hz with thermal magnetic release and Ics 100% of Icu with rupturing capacity 16 KA - 01 No. (b) Outgoing MCCB 4 pole 415V, 63 Amps, 50Hz with thermal magnetic release and Ics = 100% of Icu with rupturing capacity 16 KA - 01 No. (c) Outgoing MCB SPN, 32 Amps 10 KA 'C' series 230V AC supply- 01 No (d) Panel mounted type digital multifunctional energy meter A, V, Z, KW, PF CT operated, LT 3 phase, 4 wire, including ct ratio 400/5 - 01 No (e) LED indicating lamps sets RYB - 01 Set (f) Astro time switch-01 No

S&F pole junction box sheet moulded compound (SMC) type with hinged door and locking arrangement of size 250 X 250 X 150 mm (internal ) comprising one , one No SP MCB single pole of capacity 6 Amps 240 volts and one No terminal for loop in & loop out suitable for three phase street light system including nuts and bolts and connecting up complete, MS clamp fabricated from 25x3mm MS flat iron complete all as specified and directed.

S&F Suitable shape street light fitting bracket made out of GI Pipe 40 mm dia medium grade or of suitable size as per requirement and shape, clamps made out from MS flat of size 40 mm x 6 mm with nuts and bolts (length of pipe should not less than 1.5 m ) and applying single coat of aluminium paint over a coat of red primer painting complete all as specified and directed .

M&L for special factory made earthing electrode comprising of hot dpped galvaized MS flat inserted in to GI pipe of 88mm bore (outer), 3m length, filled with non magnetic anti corrosive material specially developed for ground resistance enhancement power around the electrode to retain moisture conforming to IS 3043 including necessary boring in ground of 200mm dia in any type of strata connecting to test point, the earth resistance shall be less than 3 ohms including provision of FRP earth pit cover complete all as specified and directed. Contractor shall improve the earthing resistance within the permissible limit without any extra cost. "MAKE: Fast Electrode / ASHLOK/ ITorrent/ U-Protec.

Note: (i) GI earthing pipe should have successfully tested for salt spray test (corrosion test) Certificate for minimum 500 hours. The Earthing Electrode should have a GTP & Drawing approval from MSEDCL infra Project. The Earthing Electrode should be tested in MSME. Any one such Earthing Electrode should have successfully type test certification by CPRI (Central Power Research Institute, Govt of India) for the Short Time current at 43 kA rms for 1 Sec; with initial peak of 90.12 kA. The rated voltage for testing in CPRI should be 400 V at rated current of 10kA. The Earth Enhancing Compound should have Test certification from NABL accredited Lab. It should be tested as per IS 1350 / AHPA guideline’s. The pH value of Compound should be 7.59, Moisture % by mass should be 8.91 & Solubility in 1:1 HCL should be 32.29 %. The Compound should be tested ELV Test as per protocol IEC 62321/111/54/CDV/ICP-OES for contain of Lead (23.0 ppm), Cadmium (15.0ppm), Mercury (Below Detection Level) & Hexa-chromium (Below Detection Level). (ii) (ii) Rate for FRP earthing pit cover shall be deemed to be included in rate quoted.

M&L for painting with aluminium paint of approved brand and manufacture to give an even shade on existing street light poles with two coats including cross arms, channels, flat iron and clamps etc, painting three black/red bands at lower portion of pole each of 300mm height and pole numbering after preperation of lod painted steel surface by scraping with wire brush/sand paper complete all as specified and directed.

Supply and fix new generation energy saving and environmental friendly long life LED street light 60 watt made up of pressure die cast aluminium housing with high power LED as lighting source and lens embedded PC cover having TOP Opening seperate driver compartment with IP66 protection and impact resistance of IK07 including fittings & connection on existing street light pole bracket complete all as specified and directed.

LIGHTENING PROTECTION SYSTEM S&F air termination single pointed aluminium rod of 12mm dia 1200mm long complete all as specified and directed.

M&L for special factory made earthing electrode comprising of hot dpped galvaized MS flat inserted in to GI pipe of 88mm bore (outer), 3m length, filled with non magnetic anti corrosive material specially developed for ground resistance enhancement power around the electrode to retain moisture conforming to IS 3043 including necessary boring in ground of 200mm dia in any type of strata connecting to test point, the earth resistance shall be less than 3 ohms including provision of FRP earth pit cover complete all as specified and directed. Contractor shall improve the earthing resistance within the permissible limit without any extra cost. "MAKE: Fast Electrode / ASHLOK/ ITorrent/ U-Protec. Note: GI earthing pipe should have successfully tested for salt spray test (corrosion test) Certificate for minimum 500 hours. The Earthing Electrode should have a GTP & Drawing approval from MSEDCL infra Project. The Earthing Electrode should be tested in MSME. Any one such Earthing Electrode should have successfully type test certification by CPRI (Central Power Research Institute, Govt of India) for the Short Time current at 43 kA rms for 1 Sec; with initial peak of 90.12 kA.

The rated voltage for testing in CPRI should be 400 V at rated current of 10kA. The Earth Enhancing Compound should have Test certification from NABL accredited Lab. It should be tested as per IS 1350 / AHPA guideline’s. The pH value of Compound should be 7.59, Moisture % by mass should be 8.91 & Solubility in 1:1 HCL should be 32.29 %. The Compound should be tested ELV Test as per protocol IEC 62321/111/54/CDV/ICP-OES for contain of Lead (23.0 ppm), Cadmium (15.0ppm), Mercury (Below Detection Level) & Hexa-chromium (Below Detection Level).

S & F earth pit indicator made out of MS sheet of 16 SWG of size 30 x 20 cm welded to angle iron of size 25 x 25 x 3 mm at a height 1 M above ground complete all as specified and directed.

S&F epoxy base insulator of suitable size, 35mm height fixed on PCC blocks / wall / MS angle / Pipe / channel/ on towers / on Galvalume sheet with and including bolt size 8 mm dia, 19 mm length, nuts and washers etc complete all as specified and directed.

S&F mild steel with powder coated simens gray inspection boxes / test point boxes 250 x 200 x 100 mm made out of 16 gauge with top cover including provision of fixing of 2 Nos epoxy insulator with and including insulating PVC sheet for incoming and outgoing copper strip for proper insulation etc complete all as specified and directed.

M&L for PCC block of size 150 x 150 x 150mm in PCC (1:3:6) type C-1 with 20mm stone graded aggregate for fixing on roof conductor / air termination rod / GI strip etc. complete all as specified and directed.

Frends Enterprises (BID ID -3495737)

VIRENDRA FABRICATORS (BID ID -3495739)

Baljeet Singh Choudhari (BID ID -3495598)

M/s S. R. Constructions (BID ID -3495346)

Manak landmarks (BID ID -3502464)

Hariom Projects Pvt Ltd (BID ID -3495986)

D R CONSTRUCTION (BID ID -3496349)