PROVN OF COVERED SHED AT NABAGRAM MILITARY STATION UNDER GE (PROJECT) PANAGARH

Amount

Excavating in trenches, n exc 1.5 m wide and n exc 1.5m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sqm on plan and getting out soft/ loos soil complete all as specified and as directed.

M&L for plain cement concrete Type D2 1:4:8 (40 mm graded aggregate) in foundations, filling and mass-concrete complete all as specified and as directed.

M&L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

All as per item No 3 here in before but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders complete all as specified and as directed.

Use and waste Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter for fair finished surfaces of concrete complete all as specified and as directed.

Use and waste Formwork to sides of pillars, posts, struts, piers, columns etc for fair finished surfaces of concrete complete all as specified and as directed.

M&L for RCC of type B1 (1:2:4) using 20mm graded aggregate as in foundations, beam, plinth beams, base of columns etc basement slabs complete all as specified and as directed.

M&L for RCC of type B1 (1:2:4) using 20mm graded aggregate as in columns, pillars, piers, post and struts etc complete all as specified and as directed.

M&L for mild steel Roof trusses (framed),Vertical post, trussed purlins crane gantries, rails and fastenings and heavy bracket framing (Square or Rectangular hollow sections) including distance pieces, cleats etc. conforming to Fe-290 Gde-165 complete all as specified and as directed.

M&L for framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging also fastening and fixing conforming to Fe-290 (Gde E 165) complete all as specified and as directed.

M&L for Brickwork with fly ash bricks, straight or curved on plan exc 6m mean radius, built in cement morter (1:6) complete all as specified.

M&L for rendering 10 mm thick in cement morter (1:6) on brick/concrete wall surfaces of any description, and finishing the surfaces even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15mm thick in cement morter (1:4) on brick masonary surfaces or concrete surfaces on other than fair face of wall surfaces with sponge finish, complete all as specified and directed.

M&L for preparation of newly plastered surfaces of wall and applying two coats of cement base paint over a coat of chalk whiting primer all as specified and directed.

M&L for preparation of newly plastered surfaces of work and applying two coats of oil bound distemper and over a coat of chalk whiting over and incl a coat of 1 mm wall putty all as specified and directed.

M&L for Preparation of New or previously untreated steel surface or any description, over 10cm in width or girth, not otherwise described and applied two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified.

M&L for Preparation of New or previously untreated steel surface or any description n exc10cm in width or girth, when unconnected with other painting or when painted in a different tint and applied two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified.

M&L for for sand or stone dust filling and sand or stone dust cushioning under floors or in foundations including watering and consolidation complete all as specified and directed.

M&L for hard core of broken stone broken to gauge not exc 63 mm deposited, spread and levelled in layers not exc 15cm thick, watered and rammed to a true surface complete all as specified and as directed.

M&L for 100mm thick for cement concrete type D-2, 1:4:8 20 mm graded aggregate as in sub base of floor and path complete all as specified and as directed.

M&L for Non - skid Ceramic coloured tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed.

M&L for Glazed coloured ceramic tiles in vertical surface 350x250x7mm/450x350x7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match complete all as specified.

M&L for rendering 10 mm thick in cement morter (1:4) on brick or concrete wall surfaces of any description for receiving of vertical tiles complete all as specified and directed.

M&L for screed bed or bedding layer 15 mm thick in cement mortar (1:6) on floors for laying floor finish complete all as specified and as directed.

S&F pre painted galvalume aluminium zinc coating GI based corrugated corrugated steel sheet 0.5mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F pre painted galvalume aluminium zinc coating GI based Plain steel sheet 0.5mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

M&L for PCC type B1 (1:2:4) using 20mm graded aggregate as in Ditto, in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bedplates, kerbs not provided for in Item 04028, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed

Returning, filling in, including spreading, levelling, watering and well ramming in layers n. exc 25cm complete all as specified.

Removing excavated material n.exc 50m and depositing where directed at a level n.exc 1.5m above the starting point complete all as specified.

M&L for point wiring with 1.5 sqmm size single core multi stranded copper conductor unsheathed PVC insulated 1100V grade cable drawn into and including casing capping sleeves and caps of adequate width and length with accessories and fittings like bend, elbows, crosses wall crossing etc for one light/fan/call bell point controlled by one switch and with continuous earth wire as one number cable 1.5 sq mm copper conductor PVC insulated (FRLS), unsheathed connected to earth dolly and to be connected to pvc box of min 1.6 mm thick having 4 Nos nuts to 4 corners ,housing switches, sockets outlet and regulators etc. complete complete all as specified and as directed.

All as per item No 30 here-in-before but for one 5 Amp socket outlet independent board complete all as specified and directed

All as per item Ser No 30 above but for one 15 Amp socket outlet independent with 2 run of cable of size 4 sq mm and one run of 2.5 sq mm cable as earth continuity all as specified and directed

M&L for submain wiring with two single core PVC insulated unsheathed stranded copper conductor 6.0 sqmm (nominal area) drawing through PVC casing capping and 4.0 sqmm stranded copper conductor cable PVC insulated and unsheathed (green colour) 1100 volts grade for earth continuity conductor and connecting with main earth dolly Note:- (i) 2 runs of 6.0 sqmm cable and 1 run of 4.0 sqmm single core copper cable and 1 run of PVC casing capping shall be measured as single run.

S&F socket loutlet 3 Pin 5/15 Amp piano flush type all as specified and directed.

S&F switch piano, flush type single pole one way 5 Amps all as specified and directed.

M&L for ceiling rose surface type bakelite 65X50 mm two or three terminals complete all as directed.

Supply and fixing switch socket combination multipurpose 15 A flush type, 5 in 1 240 volts all as specified and directed.

Supply and hanging ceiling fans complete with blades, down rods, electronic regulator and acessories, 230 V, 1400 mm sweep, min Air delivery 210 CFM, with squirrel cage induction motor with hanging hook complete all as specified and directed.

Supply and fixing LED light fitting 20Watt with and including LED tube rod 4 feet long suitable for single phase 230V 50 Hz AC supply made with aluminum extrusion complete with all accessories internally prewired and including connecting up with three core flexible copper conductor cable of size 1.5sqmm( nominal area ) complete. Make Philips Cat part No - B085P2D5KS or eqv bajaj,havells,crompton, wipro etc

Supply and fixed MCB DB Single pole and neutral 12 way double door with 200 amps rated bus bar complete all as specified and directed.

Supply and fixed MCB four pole 'C' Curve 240 Volts of capaicty 63 Amps 10 KA rating complete all as specified and directed.

Supply and fixed MCB single pole 'C' Curve 240 Volts of capaicty 20 Amps 10 KA rating complete all as specified and directed.

Materials and Labour for earthing complete with galvanized steel earth plate electrode 600 mm x 600 mm x 6.0 mm thick buried directly in ground end vertically to a depth not less than 2.25 meter deep below ground level with top edge of the earth plate at a depth not less than 1.5 M below normal ground level connected to galvanized iron strip 32x6mm as earthing lead by means of bolts, nuts check nuts and washers of galvanized steel and connected to main switch board or main control board as directed and provision of concrete pit in PCC (1:3:6) type C1, pre-cast RCC (1:2:4) type B1, cover slab 54 cm x 54 cm x 5 cm, reinforced with 8 mm dia TMT bars @ 150 mm c/c both ways, one handle for lifting made out of 10 mm dia MS round bar, provision of funnel, wire mesh, 20 mm bore galvanized steel tubing (Medium grade) for watering, charcoal or coke and salt in alternate layers, 15 mm bore galvanized steel tubing (light grade) for protection of earth lead connection, including necessary excavation and earth work in any type of soil, dismantling and taking out old earthing plate and necessary testing complete all as shown on electrical plate No 5 of SSR Part –I (2009).

M&L for sand cushioning with clean dry sand for protection of under ground cable complete all as specified and as directed. Note :- Punned thickness of sand layer shall be measured and paid to contractor.

Supply and laying Sub Class "B" Bricks Designation 75 as in cable Protection complete all as specified and as directed.

Material and labour boring of horizontal holes /trenchless hole for 50 mm bore pipe under the road below 1.50 mtr from the road/hard surface by trencheless technology using ultrasonic technique and including necessary machine without damaging the existing road and getting out in any type of soil and disposal of soil to a distance not exceeding 50 m from the site of work all as directed. Note: Pipe Shall be measured and paid seperately.

Supply and fixing galvanised iron tubing 40 mm bore, light grade with all fittings & fixture as in cable protection laid in trenches/floor or on the Pole etc complete all as specified and directed.

Suppy, laying, jointing and testing XLPE insulated, armoured, heavy duty electric cable with aluminium conductor, 1100 volt grade, cross sectional area 25 Sqmm 3.5 core complete all as specified and directed.

Supply install, testing & commissioning factory made LT feeder pillar box out door type factory made totally enclosed dust and vermin proof single opening with double leaf shutter duly hinged with locking arrangement made of MS Angle iron frame work and CRCA Sheet of 3.15mm thick as per IS 5039 dually painted with epoxy base powder coated paint of approved shade over a coat of Red Oxide Zink Chrome Primer neccessary holes Shall be kept on the kiosk box for incoming and outgoing cable entry. All Holes Shall be provide with brass cable gland of appropriate size.The feeder piller Box Shall be Suitable for 415 volts ,50 Hz ,3 Phase 4 wire System and shall be completed with 300 amps Capacity Aluminium TPN Busbar Chamber Having TPN 3 Phase 4 Wire System Fixed on Porcelain Insulator with Suitable size PVC copper Conductor duly Sleeved with 4 Coloured heat Shrinkable PVC Sleeve, thimble Glands and shall be compolete all as directed with the following accessories .The cost PCC Plat form and dismantling of old U/S Panel Board shall be deemed to include in the coated rate of above said item complete all as specified and directed. (i) MCCB 4 pole TPN , 100 Amps ,16 KA, 415 Volts, 50 Hz - 01 Nos ( As incoming) (ii) MCB SPN 40 Amps 'C' Curve - 2 Nos (Out going) (iii) LED phase Indicator lamp (R,Y,B) with MCB SP 2 amps showing 3 phase supply switch control – 03 Nos (iv) LED Multi Function meter for Showing Multy parameters -01 Nos

Note: In case doubling/duplicancy of BOQ items , the lowest quoted rate shall be applicable for payment.

Abida Enterprises

HIGH HILLS INFRA

M/S New Builders Corporation

ANSH CONSTRUCTION

M/S SINGH ENTERPRISE

BISWAS ENTERPRISE