SPECIAL REPAIR TO OFFRS MD ACCN BLDG NO P-08 AT GWALIOR ROAD UNDER GE (EAST) AGRA

Amount

Taking down of All loose and de-bonded concrete/ screed, loose particles, dirt etc & Debris should be removed from Bldg. Roof substrate must be pressure-washed with water with, a minimum working pressure of 1,400 psi is to be used to and/or remove all dirt, dust, chalking and waste products. Remove algae, mold by using bleach solution or biowash etc complete all as specified & directed by Engr-in-Charge.

M&L apply one coat of Cipoxy 16D primer in the ratio 1:1 spreading at the rate of 0.200 kg-0.250 kg /sqm in complete dry condition where moisture contain below 7% (should be checked with moisture meter)Allow the primer coat to dry for 6 to 8 hours. Apply 1st coat of Roofseal Classic without dilution spreading at the rate of 0.70/litre/Sq.mt/Coat until all surface is covered. Lay a 45 GSM Fibre glass mesh as a reinforcing material which is incorporated in the coating when the first coat is still in wet condition. Allow the first coat to dry for approximately 4 to 6 hours. Apply the second of chemical with the same application coverage, but in a direction perpendicular to that of the first and second coats. Allow each coat to air cure for a minimum of 4-6 hours after application. Check to see no void surface is left untreated / uncoated.Allow the system to air cure for 7 days minimum etc complete all as specified & directed.

M&L for repair of All visible hairline cracks on concrete roof / screed more than 0.50 mm and not giving hollow sound, should be cut and widen in V shape with mechanical cutter in the size (10mm W x 6mm D). Fill cracks with PU sealant / Hybrid Sealant with suitable gun and smoothed with a putty knife or trowel. Allow sealant to cure a minimum (72 Hrs.) 3 days etc complete all as specified & director.

M&L for Remove loose and damaged concrete roof screed in pockets with mechanical cutter. Clean the concrete screed with high pressure water jet to remove dirt and loose particles. Brush apply a bond coat of Pidicrete URP mix in the ratio of 1:1 (URP 1: Cement 1) by volume to make it lump free slurry when applied on in the pre wet surface. Laid to fall roof screed in correct slope and gradient. Mix Dr. Fixit Pidicrete URP 10% by weight of cement in average thickness 25 mm concrete in ratio of 1:1.5:3 i.e., one bag of 50kg cements: 1.5 times volume of sand: 3 times volume of aggregates: 25L water. Level the repair mortar and finish with trowel. Moist cure should be done for 7days. Air cure screed for 7days, before application of roof top coat coating system etc complete all as specified & directed.

M&L 25 mm thick PCC 1:2:4 type B-1 (12.5mm graded aggregate) with water proofing compound as per manufacture instructions neat cement slurry with 3.0kg of cement per Sqm complete all as specified and as directed. Note : water proofing compound shall be measured and paid separately.

Demolition of cement concrete(unreinforced) of any description and in any position not otherwise specifically provided complete all as specified and directed.

M&L Cement concrete in sunkan portion filling in mass concrete Type E2 1:5:10 (using 40mm graded aggregate) Including demolition of cement concret complete all as specified and directed .

M&L for Rendering 10mm thick in CM 1:3 using water proofing compound as per manufacture instruction finished even and smooth without using extra cement and curved adqutely and after drying apply two coats of Brushbond Aquaprotect of Fosroc or equivalent both on floor and walls of sunken poriton and tested complete all as specified and directed.

Supply only liquid water proofing compound complete all as specified and directed.

Demolition of cement concrete (reinforced) in roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work complete all as specified and directed.

Disposal off/removal of old demolished material exc 1.50 km but n. exc 5 km and depositing where directed complete all as specified and directed

M&L RCC Type B0 1:2:4 Type using (12.5mm graded aggregate) in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves including necessary form work complete all as specified and directed.

S&F 5.0 cm thick sand stone slabs in sun shades, chajjas, shelves, roof slabs etc n.exc. 2m in length punched dressed on face and along exposed edges, self faced on other side and set and pointed in CM 1:4 complete all as specified and directed.

M&L PCC 1:3:6 type C-2 (using 40 mm graded crushed stone aggregate) as in plinth protection ( 75 mm thick ) laying in alternate ways finished even and smooth without using extra cement plinth protection shall be laid to alternate bay system each bay shall exceed 3m in lentgth 12mm wide and 75mm deep joint sall be filed with hot blown bitumen 85/25 and sand complete all as specified and directed.

Demolition of brick work or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars etc but excluding ashlar ficings, dressed stone work and pre-cast concrete articles complete all as specified and directed.

M&L for brick work with sub class ‘B’ bricks old size, straight or curved on plan exc 6 M mean radius, built in CM 1:6 complete all as specified & directed

M&L brickwork with sub-class `B' brick straight or curved on plan to any radius in half brick thick walls built in CM 1:4 complete all as specified & directed

Taking down cement or cement lime plaster of any discription on brick or stone walls/ ceilings etc, including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M &L for 10 to 12mm smart care ready mix repair plaster is a specially designed ready to use cement based plaster with high quality polymer additives and well graded sand and fillers which can be used for plastering (as per manufacture instructions) over exterior wall ( including necessary arrangements in multy storey bldgs up to G+1 )surfaces complete all as specified and directed. ( coverage area 24-28 kg/sqm)

M &L for 10 to 12mm smart care ready mix repair plaster is a specially designed ready to use cement based plaster with high quality polymer additives and well graded sand and fillers which can be used for plastering (as per manufacture instructions) over interior wall surfaces complete all as specified and directed. (coverage area 24-28 kg/sqm specified .

M & L Washed stone grit plaster on exterior walls in two layers, under layer 12mm cement plaster 1:4 (1 cement: 4 coarse sand ) furrowing the under layer with scratching tool, applying ement slurry on the under layer @ 3 Kg of cement per square metre, top layer 15mm cement plaster 1:1/2:2 (1 cement: 1/2 coarse sand : 2 stone chipping 10mm nominal size) in panels with groove all around as per approved pattern including scrubbing and washing, the top layer with brushes and water to expose the stone chippings .complete all as specified (Payment for providing grooves shall be made separately).

Forming groove of uniform size 15mm wide and 15mm deep in the top layer of washed stone grit plaster as per approved pattern using wooden battens, nailed to the under layer including removal of wooden battens, repair to the edges of panels and finishing the groove complete as per specifications and direction.

M&L for preparation of new plastered or unplastered surfaces of wall, concrete surfaces, and applying two or more coats of acrylic emulsion polymer paint having (waterproof rain coat of Dr fixit or eqivelent) Alkali & fungal resistance, dirt resistance exterior paint of required shade over and including priming coat of exterior applied @ 0.90 litre/10 Sqm over new surfaces of wall complete all as specified and directed.

M&L for preparation of complete removal of existing treatment or unplastered surfaces of wall, concrete surfaces, and applying two or more coats of acrylic emulsion polymer paint having (waterproof rain coat of Dr fixit or eqivelent) Alkali & fungal resistance, dirt resistance exterior paint of required shade over and including priming coat of exterior applied @ 0.90 litre/10 Sqm over new surfaces of wall complete all as specified and directed.

M&L preparing newly plastered or un plastered surfaces of wall and applying two coats of oil bound distemper with roller application over a coat of average 1mm thick birla wall care putty on new plastered surfaces complete all as specified and directed.

M&L for applying two coats of oil bound distemper with roller on old decorated wall surfaces over average 1mm thick wall care including complete removal of existing treatment with mechanical complete all as specified and directed.

M&L Preparing newly plastered or un plastered surfaces of ceiling surface and applying two coats of oil bound distemper with roller application over a coat of primer over a coat of average 1mm thick wall care putty on new plastered surfaces complete all as specified and directed.

M & L cutting holes into or through brick wall built in cement mortar superfacial area not exc 150 Sqcm and making good in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required complete all as specified and directed.

M & L cutting holes into or through brick wall built in cement mortar superfacial area exc 150 Sqcm not exc 400 Sqcm and making good in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required complete all as specified and directed.

Removing or dismantling of damage / cracked/ concrete /loose concrete / plaster of celing/ wall/ chajja/ facia to expose the sound and hard concrete using a suitable mechanical device or by hammer and chisels etc complete all as specified & directed.

M & L for applying bonding agent for bonding old to new concrete surface likes chajja/ beams/ celings/ columns/ facia etc by high performance modified Styrene- Butadiene Rubber ( SBR ) base binder . Applying of binder is as 10 sqm/ per litr ( including necessary arrangements in multy storey bldgs up to G+2 ) etc complete all as specified & directed.

M & L for applying 30 mm thick ( average ) polymer modified repair mortar for repair of RCC members likes beams, columns, chajja , facia , mortar having good compressive strength should not less than 30 Mpa and shrinkage resistance, mixing as per manufacture instruction etc ( including necessary arrangements in multy storey bldgs up to G+1) complete all as specified & directed.

S&F galvanized welded steel wire fabric as extra reionforcement to RCC members like ceilings, chajja’s, beams, columns parapet walls, waste slab etc including all cutting and waste (wt not exc 4.00 kg/Sqm) complete all as specified and directed.

M&L for treatment of soil under existing floors using emulsion @ one litre per litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement :2 coarse sand) to match the existing floors

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) complete all as specified and directed.

M&L for coloured glazed ceramic tiles in vertical surface 450 x 300 x 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match tiles including 10mm thick rendering in CM 1:4 on brick wall complete all as specified and as directed .

M&L vertified double charge dark shade tiles 10 mm thick (square/rectangular) light shed area of each tile exceeding 0.42 Sqm but not exc. 1.00 Sqm as in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles laid over and including 15mm thick screed bed or bedding layer of cment mortar (1:6) complete all as specified and directed.

All as per Item No 37 above but in skirting over 10 mm thick rendering in CM 1:4 complete all as specified and directed.

M&L non skid joint free coloured tiles (1st quality/ premium quality) 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 Sqm but not exc. 0.18Sqm as in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles laid over and including 15mm thick screed bed or bedding layer of cment mortar (1:6) complete all as specified and directed.

M&L 25 mm thick PCC 1:2:4 type B-1 (using 20 mm graded stone aggregate) as in sub base of flooring finished even and fair without using extra cement complete all as specified & directed.

M&L Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete laid over and including 20mm thick screed bed CM (1:6) complete all as specified and directed.

M&L Machine cut kota stone 20-25 mm thick as in riser of step, skirting,dado and pillar etc. laid and jointed with grey cement slurry mixed with pigment to match the shade of the stone including grinding and polishing laid over and including 15mm thick rendering CM (1:4) complete all as specified and directed.

M&L 18/20mm thick black granite (of any type) work (table rubbed and polished) in steps jambs, pillars, window cills, cooking plateforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match the shade of stone including rounding and moulding of edge and making hole for cooking gas pipe complete all as specified and as directed.

Boring holes through cooking platform lining for pipes ,etc n'exc 50mm dia and making good complete all as spd and dir by Engr-in-charge.

S & F in repairs 15 mm bore chromium plated fancy bib taps long body, cast copper alloy, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S&F in repair 15 mm bore CP Stop valve / angle valve screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified & directed.

S&F 15 mm bore CP wall mixer 3 in 1 for mixing hot and cold water provn of both hand shower and over head shower screwed down for iron pipe and fixed complete all as specified & directed.

S&F 15 mm bore CP WHB mixer for mixing hot and cold water screwed down for iron pipe and fixed complete all as specified & directed.

S&F in repair 15 mm bore CP Sink mixer swan neck for mixing hot and cold water screwed down for iron pipe and fixed complete all as specified & directed.

S&F in repair PVC Bath cabinet mirror (single door) and fixed to chromium plated brass screw and cup washers complete all as specified and directed.

S&F in repair sheet glass shelf assembly consisting of 5.50mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed

S & F in repair Soap dish chromium plated and fixed to chromium plated brass screw and cup washers complete all as specified and directed.

S & F Corner shelf with frame triple chromium plated complete all as specified and directed.

S & F in repair Toilet paper holder chromium plated complete all as specified and directed.

S & F in repair tubular towel rail 60 cm length of stainless steel 20 mm Dia with brackets type fixed with and including chromium plated brass screws and wooden/plastic cleats complete all as specified and directed.

S & F in repair health faucet with 15mm dia 1 mtr long flexible tube and wall hook chromium plated complete all as specified and directed.

S&F in repairs 10 ltrs capacity PVC flushing cistern low level (white) with inlet ball valve and handle including flush pipe, brackets, rubber bush, washers etc complete all as specified and directed.

S&F in repair vitreous china squatting pan Orissa pattern size 580x440mm white with 'P' or 'S' trap front or back inlet including footrest (excluding fluxing cistern and flush pipe) complete all as specified and directed.

S&F in repair Europen water closet snow white (one piece EWC with seat cover and twin flush fitting) of size 710 x 390 x 790mm incl necessary 'P' or 'S' trap and connection to drain pipe etc with and incl necessary fixing arrangement incl seat cover manufactures instructions complete all as specified and directed.

S&F in repair fancy type vitreous china wash down water closet pan (Pedestal pattern), white with 'P' or 'S' trap incl seat and cover (excluding fluxing cistern and flush pipe) complete all as specified and directed.

S&F in repairs Vitreous china wash basin white with full pedestal flat back size 550 x 400mm incl waste pipe, and waste coupling chain plug brackets complete all as specified and directed..

S&F in repairs kitchen sink with drainage board made of stainless steel 1mm thick with plugs, washers incl bedding in CM 1:4 to dwarf wall or including cast iron cantilever brackets and connecting union to pipe, overall size 915mm x 460 mm bowl size 410mm x 330mm x 160 mm including waste coupling and waste pipe etc complete all as specified and directed.

S&F in repairs plate rack of stainless steel , 1mm thick for kitchen or labotary, overall size 750x900 x250 mm ,fixed with plugs and washers on wall all as specified and directed.

S & F in repairs CP shower rose 125mm dia along with shower min 600mm long arm complete all as specified and directed.

S&F in repair 100 mm square Stainless steel grating with openable flap complete all as specified and directed.

S&F in repair PVC connection 15mm size with PTMT nuts, 600 mm long complete all as specified and directed

S&F in repair 500 ltrs capacity rotational moulded polyethylene water storage tank tripal layered, ISI engraved (cylindrical vertical with closed top) hoisted and fixed in position complete all as specified & directed.

S&F in repair 1000 ltrs capacity rotational moulded polyethylene water storage tank double layered, ISI engraved (cylindrical vertical with closed top) hoisted and fixed in position complete all as specified & directed.

S&F in repair 20mm dia ball valve high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe 20 mm dia (minimum weight - 210 gm) complete all as specified and directed.

Taking up or down 15mm bore steel tubing and connection including cleaning for re-fixing or removal from site complete all as specified and directed.

All as per item No 71 above but 20mm bore complete all as specified & directed.

S&F 15mm bore GI tubes medium grade, galvanised with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified and directed.

S&F 20mm bore GI tubes medium grade, galvanised with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified and directed.

S & F in repair 20mm dia Gun metal globe or gate valves with iron wheel head screwed both ends for iron pipe complete all as specified and directed.

Taking down PVC Soil waste and rainwater pipes (any size or pattern) including all fittings etc complete all as specified & directed.

S & F 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall including all necessary fittings( Band, Tee) and fixing of 100Cm/centre to centre clamps out of 50 mm by 5 mm flat iron fixed with suitable bolt / screws securing etc complete all as specified and as directed.

S & F in reapir 110mm bore PVC HDPE high density polyethylene pipes single socketed in any length with rubber ring joints fixed to laid in tranches etc complete all as specified and as directed.

S & F in reapir 75mm bore PVC (SWR) HDPE high density polyethylene pipes single socketed in any length with rubber ring joints fixed to wall including all necessary fittings and fixing of 100Cm/centre to centre clamps out of 50 mm by 5 mm flat iron fixed with suitable bolt / screws securing etc complete all as specified and as directed..

S & F in reapir 75mm bore PVC(SWR) HDPE high density polyethylene pipes single socketed in any length with rubber ring joints fixed to laid in tranches etc complete all as specified and as directed..

S & F 75 mm bore PVC (SWR) HDPE high density polyethylene pipes bends sith complete fittings of any radius complete all as specified & directed.

S & F 110 mm bore PVC (SWR) HDPE high density polyethylene pipes bends with complete fittings of any radius complete all as specified & directed.

S&F 110 mm bore PVC (SWR) HDPE high density polyethylene pipes single T with access door of any radius complete all as specified & directed.

S & F 110 mm bore PVC (SWR) HDPE high density polyethylene pipes cowl of any radius complete all as specified & directed.

S & F in repair 100mm dia cast iron Nahani trap, with grating including jointing to waste pipe fixed in cement concrete

S & F in repairs 100mm dia of cast iron floor trap, plain with grating incl jointing with solvent cement concrete type B-1 (1:2:4complete all as specified and directed complete all as specified and directed.

Dismantling unframed work timber scantling 40 Sqcm and over in section complete all as specified and as directed

Dismantling of wrought iron of mild steel work of any description not otherwise poivided complete all as specified and directed.

S&F for framed work such as grills, grating etc. with ends of bars shouldered and/or riveted or forged into spike, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railing framed work of water tank and similar work confirming to Fe 290 Gde E-165 complete all as specified and directed.

M& L for SS railing pipe shall be stainless steel, non magnetic type conforming to Grade 304, the bracket shall be fixed with SS counter sunks, flush screws to SS insert plates etc. including profile cutting, welding using special electrodes for stainless steel welding and anchor fasteners / fixing arrangements etc complete all as specified & directed.

S&F mild steel joist channel angle or tee sections fixed independently with out connecting plates etc of grade Fe-410-W (Gde E-250 quality B) complete all as specified and directed..

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) n. exc 1.5 Sqm each complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) exc 1.5 Sqm but not exc 4 sqm each complete all as specified and directed.

M&L for Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 65X100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be madeetc complete all as specified and directed.

M&L for Factory made WPC (Wood Polymer Composite) Double Rebated frame of solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 65x125 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp?ressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be madeetc complete all as specified and directed.

M&L for Factory made WPC (Wood Polymer Composite) Single Rebated frame of solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45x70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp?ressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be madeetc complete all as specified and directed.

S&F for factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and including fixing with 100mm long stainless steel butt hinges -04Nos with necessary full body threaded star headed counter sunk S.S screws, complete all as per specified and directed.

S&F 35 mm thick Factory made solid panel PVC wire gauzed door shutter 35 mm thick i.e. panel will be of wire gauze of wood grain printed PVC sheet panel. The wire gauze shall be wrapped on an additional square 8mm M.S. Solid tube and this tube shall be welded to M.S. tubes. The wire gauge shall be stretched to tighten firmly consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded wood grain printed PVC sheet used instead of plain colour PVC sheet & 5mm thick x 15mm wide PVC sheet beading used inside stiles and rails and decorative PVC beading of 10mm x 10mm used beading of exposed portion of PVC sheet beading channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing including fixing with 100mm long stainless steel butt hinges -04 Nos complete all as specified and directed.

S&F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tack or galvanised wire staples complete all as specified and directed.

S & F in repair Factory Made 18mm thick 100% Solid WPC ( Wood polymer Composite ) decorative Laminated Board of required size comprising of virgin PVC resin of K Value 57-60 ( Suspension Grade ), Calcium Carbonate and natural fibers ( Wood Powders/ rice husk/ wheat husk ) and Non toxic additives, made from Extrusion process WPC foam sheet Single Extruded ( Inner ) with having minimum density not less than 650 kg/cbm manufactured by Certified Company, having good screw holding capacity ( Screw Withdrawal strength of 2000 N ( Face ) & 1100 N ( Edge ), Minimum Compissive of 50 N/mm2 , Modulus of elasticity 850N/mm2 and resistance of spread of flame of Class A category with Property of being Termite/ Borer Free.Water/ Moisture Proof and Fire Retardant. WPC to be Laminated with PVC foil of minimum 14 microns thick of approved design pasted on both faces of shutter and fixing stainless Steel butt hinges of required size with necessary full body threaded star headed counter sunk SS Screws and all required frame as per site requirement. Material test certificate and authentication should be compulsory provided by the manufacturing company : For Kitchen Doors and Cabinets.complete all as specified and directed.

S&F 100 mm long stainless steel hinges type B-12 complete all as specified and directed.

S & F for 30mm witdth of flaps (when open) continuous (piano) hinges, stainless steel complete all as specified and as directed.

S&F 150 mm long stainless steel, barrel tower bolts of extruded section complete all as specified and directed.

S&F 300 mm long stainless steel, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or stainless steel complete all as specified and directed.

S&F 150 mm long stainless steel handles, complete all as specified and directed.

S & F 100mm Stainless steel handle for kitchen cabinet complete all as specified & directed.

S&F Floor door stopper 150 mm long of stainless steel body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified & directed.

S & F PVC door( back side) stopper 75mm long complete all as specified & directed.

S & F mild steel 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified & directed.

S&F 125mm long stainless steelHasp and Staple, safety type including bolt to hinge plate and fixed with screws complete all as specified and directed.

M&L cement concrete 1:3:6 type C-1 (using 20mm graded stone aggregate) as in bed blocks for fixing hold fasts etc. complete all as specified and directed.

S & F aluminium powder coated casement window using aluminium section as per Jindal for frame sec no 20558, shutter Jindal sec no 20559, mullion sec 20560 glazing clips Jindal sec no 17523 and 19391, including 5 mm thick sheet glass, including necessary joining clips, glasing clips, rubber gasket, hinged/ pivot, handles, locking arrangements including taking down of exsting steel window etc complete all as specified & directed.

S & F aluminium powder coated casement window using aluminium section as per Jindal for frame sec no 20558, shutter Jindal sec no 20559, mullion sec 20560 glazing clips Jindal sec no 17523 and 19391, stainless steel wire cloth netting ( 0.36 mm nominal dia) and (average width of aperture 1.40 mm ), including necessary joining clips, glasing clips, rubber gasket, hinged/ pivot, handles, locking arrangements including taking down of exsting steel window etc complete all as specified & directed.

S & F aluminium ventilator frame/shutters powder coated, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. including taking down of exsting steel window complete all as specified and directed.

S & F in repair stainless steel curtain rods or 25mm dia as in doors/windows SS brackets fancy type including screws and other necessary fitting (Knob) for fixing brackets SS funnels for 25mm dia dropry rod fixed at each end of rods compete all as specified and directed.

S & F 20mm dia stainless steel pipe for cupboard compete all as specified and directed.

M & L for applying two coats of synthetic enamel paint over a coat of red oxide primer including preparation of new steel surface over 10 cm width or girth, not otherwise described complete all as specified and directed.

M&L for preparation of old painted steel surfaces & applying one coat of synthetic enamel paint on steel surface of any description over 10 cm in width or girth complete all as specified and as directed.

Excavation in trenches not exceeding 1.5 M wide and not exceeding 1.5 M in depth for foundation, manholes, etc n.exc 10 Sqm plan and getting out in soft/loose soil complete all as specified and directed.

Returning filling including spreading,levelling,watering and well ramming in layers n. exc 25 cm thick complete all as specified & directed.

Demolition and breaking up drain pipes (salt glazed ware, AC or reinforced concrete) set in cement mortar including concrete bedding and haunching complete all as specified and directed for 150mm bore of pipe

Supply,laying and jointed 150 mm nominal bore dia DWC( double wall corrugated),socketed and sewage pipes having 6.00 M length,conforming to IS 16098 (Part-2) of SN-4 stiffiness with and including necessary jointing materials etc complete all as specified and directed .

M&L for providing pre-cast cement concrete 1:2:4 type B1 using 20 mm graded stone aggregate as in cover (for manholes and drains) including necessary form work set in CM 1:6 with and including demolition complete all as specified and directed. (Note :- Reinforcement shall be measured and paid separately)

M & L for mild steel TMT bar 6mm to 8mm dia cut to length, bent to shape required, including cranking, bending spirally, binding wire (0.90mm dia annealed) complete all as specifed and difrected.

Cutting into existing manholes for connecting new drain pipe, making good to pipe and rendering cutting out benching for and forming branch channel (1/2 round 3/4 Sec) in cement conc (1:2:4) type B-1smooth finished and reforming benching as reqd for 225mm bore pipe complete all as specified & directed.

M&L 60mm thick factory made chamfered edge cement concrete paver block of M-30 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc.,of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed.

M&L for 75 mm thick Cement concrete type D-2 1:4:8 (using 40 mm graded stone aggregate) in sub base of flooring/ hard standing finishing surface even and rough using broom finish complete all as specified and directed.

M& L writing/ letters to mention building details in displays card over will surface, the dimension of display card should be 90cmx 60 cm, location as decided by Engr-in- charge on the wall of each building. The display card shall indicate the following details by applying two coat of enamel painting as approved colour as specified and directed. BLDG NO/VINTAGE : (BLDG NO & YEAR) PERIODICAL MAINT DONE ON : (MONTH 2024/25) LAST SPL REPAIR UNDER TAKEN ON : (MONTH & YEAR) ADDN/ALTN/ ANY OTHER TYPE : OF WK CARRIED OUT WITH DATE

M&L acrylic plastic number plate of size 200mmX 200mm X 3mm and writing Qtr No. of height 10 to 15 cm in any style (bold/italic) and fixed to wall with screws complete all as specified & directed.

Taking down carefully existing unserviceable copper / aluminum point wiring of any description & in any position with and ncluding taking out existing unserviceable conduits or battens of any description with sunken boxes/junction boxes and all fitting, accessories & fixtures such as switches, ceiling roses, pendants, regulators, socket, light fittings, lamp holders etc but excluding tube light fittings and making good the disturbed surface of walls, floors, ceiling etc to match with the existing surfaces complete all as specified and directed.

M&L point wiring with 1.5 sqmm multi stranded copper conductor 1100 volts. grade FRLSH PVC insulated unsheathed cable with proper colour coding drawn in including PVC concealed conduit not less than 20 mm dia with all accessories and FRLSH PVC insulated 1.5 Sqmm multi standard unsheathed copper wire for continues earth, including cutting and chasing of wall surface for laying PVC conduit and modular sunken box and connecting earth and making good to the disturbed surface of wall/floor and matching with existing specifications. Connections of cable with MCB's or bus bar shall be done through proper size copper/brass thimbles. Note :Conduit shall be fixed on surface of roof with necessary saddles where concealing of conduit is not feasible at no extra cost for the following :- (a) One light /fan point controlled by one switch

(b) One 5 pin socket outlet 5 Amps on same board complete all as specified & directed.

(c) One 5 pin socket outlet 5 Amps on independent board complete all as specified & directed.

(d) One bell/buzzer point controlled by one push button on the same board with other switches or independent complete all as specified & directed.

(e) One light point controlled by two 2 - w a y s w i t c h e s , with cables 1.5 sq. mm size complete all as specified & directed.

(f) One telephone point wiring with cables 0.4 sq mm 2 core complete all as specified & directed.

(g) One TV socket point wiring with cables RG-6 Coaxial cable complete all as specified & directed.

All as per item No 131 here in before but with FRLSH cable size 4 Sq mm for one 5 pin 15/16 Amps socket out let on independent board/AC Box and multistrand insulated copper earth continuity conductor of size 4 sqmm all as specified and directed by Engr-in-Charge.

Supply and fixing modular telephone jack RJ-11 white colour fixed in 1 M box comprising of flush metal box, inner plate and outer cover, all conforming to IS 3854:1997 with finger proof terminals with captive screws having front fixing & removing features without removing plates complete all as specified & directed.

Supply and fixing modular TV coaxial socket outlet fixed in 1 M box comprising of flush metal box, inner plate and outer cover complete all as specified & directed..

Supply and fixing modular switch piano single pole, one way 6 Amps 1 module, complete all as specified and directed.

Supply and fixing modular switch piano single pole, two way 6 Amps 1 module, complete all as specified and directed.

Supply and fixing modular switch piano flush type 16 Amps single pole one way, one module, complete all as specified and directed.

Supply and fixing modular socket outlet 2/3 pin 6 Amps, 2 module complete all as specified and directed.

Supply and fixing modular socket multipurpose 3 pin 6/16 Amps combined 2 module, complete all as specified and directed.

Supply and fixing modular step type, 1/2 module electronic fan regulator 240 volts complete all as specified and directed.

Supply and fixing Modular Bell push 6A 1 module pole, one way, complete all as specified and directed.

Supply and fixing call bell, Ding dong type, 230 volts AC single pole complete all as directed.

S&F ceiling rose PVC Polycarbonate isolated body 62.5 x 25 mm, three terminals, complete all as specified & directed.

Supply and fixing modular cover plate with frame (inner and outer) 1 module for mounting switch and sockets all as specified and as directed.

Supply and fixing modular cover plate with frame (inner and outer) 2 module for mounting switch and sockets all as specified and as directed.

Supply and fixing modular cover plate with frame (inner and outer) 3 module for mounting switch and sockets all as specified and as directed.

Supply and fixing modular cover plate with frame (inner and outer) 4 module for mounting switch and sockets all as specified and as directed.

Supply and fixing modular cover plate with frame (inner and outer) 6 module for mounting switch and sockets all as specified and as directed.

Supply and fixing modular cover plate with frame (inner and outer) 8 module for mounting switch and sockets all as specified and as directed.

Supply and fixing blank spacer plate for single module all as specified and as directed.

Supply and fixing 20W Inverter LED batten with square profile and polycarbonate channel. Lithium Ion battery with charging time 8hours-10 hours and back up time upto 4 hours incluuding connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed.

Supplying and fixing 10 watt LED battan surface / wall mounted with specially designed powder coated aluminum housing, high optically efficient polycarbonate diffuser, in built electronic driver duly pre-wired upto terminal block and fixing arrangements for fixing the light fitting, complete all as specified and directed.

S&F decorative, wall mounting, brushed nickel finish fixture with Opal Glass diffuser suitable with 9 W LED lamp B22 base including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

S & F Bulk head , luminaire made of die cast aluminium housing 10 watt LED, internally prewired with and including premium quality diffuser for glarefree light and easy to install snap fit installer complete with all accessories, and connecting the same to electric source with & using PVC sheathed and insulated three core copper conductor cable of size 0.50 Sqmm and fixing arrangements for fixing the light fitting complete all as specified and directed.

Supply and fixing LED building security light fitting 35 Watt 230 V AC out-door type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection, fixed to pole or wall of building with and including suitable Bracket made out of 25 mm dia GI light grade pipe, 1.00 m long bent to shape by cutting & welding as required & directed and fixed with two Nos of FI clamps 35x6 mm to be tightened with suitable size of bolts, nut and washers and including painted with two coat of aluminium paint over a coat of red oxide primer, and including connecting the fitting to electric source with & including twin twisted copper flexible wire of size 0.75 sqmm three core with suitable size flexible PVC conduit including all accessories and fixing arrangements for fixing the light fitting and writing the date of fixing on security light with permt marker complete all as specified and directed. Note:-The period of defects liability shall be 02 Years from the date of installation of security light.

S&F post top lantern LED type 20 watt 230 watt volts AC outdoor type with decorative post top for 360 degree indirect light IP 65 protection with impact and corrosion resistant complete with driver, lamp including grouting of GI pipe medium grade not less than 32mm, complete all as specified and directed.

S&F exhaust fan (copper winding), steel body AC single Phase. 230V of size 300mm sweep with, blades, and frame and louvers complete all as specified and directed.

S&F exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 200mm complete all as specified and directed.

Taking down fan, sealing cable end, dismantling blades and removing fan and blades to store complete all as specified and directed.

Supply and fix in replacement of Intelligent BLDC (Brush Less Direct Current) Energy Saving Ceiling fan (copper winding) of size 1400mm sweep with smart remote for easy operation with 5 speed setting and smart features like boost mode and timer functionality for 2, 4,6 and 8 hours, 230 Volts, 50Hz, power consumtion is less than 35 watt, 5 Star rated, noiseless motor operation, inverter stabilization technology, 370 RPM, 245 CFM alongwith necessary accessorie like anti suicide down road 12", canopy, blades, BLDC motor, hanging clip etc and 03 year On Site warranty including writting the MES Number with synthetic enamel paint, including electrically connecting from fan to ceiling rose inlcluding suitable size flexible PVC conduit, complete all as specified and as directed.

Supply and fixing Geyser of 25 Ltrs capacity, 5 star rating AC single phase, 230 volts, Stainless Steel inner tank including connection with three core multistranded copper conductor of size 2.5 sqmm including necessary fixing arrangement i.e anchor nut, bolt, washer,CP pipe connection, grouting and making good to disturbed surface and cleaning of the area, complete all as specified and as directed.

M&L for sub main wiring using two 2x 6 sqmm single core PVC insulated, unsheathed stranded copper conductor cable of voltage rating upto and including 1100 Volts drawn in and including concealed PVC conduit (Medium grade) as required dia with standard accessories along-with one run of PVC(green colour) insulated , unsheathed, stranded copper conductor of size 1x 6 sqmm as earth continuity conductor connected to earth dolly including taking down of old unsv submain wiring complete all as specified and directed. (NOTE : Two run of single core PVC cable with one run of earth conductor and conduit /batten shall be measured as one unit.)

M&L for sub main wiring using two 2x4 sqmm single core FRLSH PVC insulated, unsheathed stranded copper conductor cable of voltage rating upto and including 1100 Volts drawn in and including concealed PVC conduit (Medium grade) as required dia with standard accessories along-with one run of PVC(green colour) insulated , unsheathed, stranded copper conductor of size 1x 4 sqmm as earth continuity conductor connected to earth dolly including taking down of old unsv submain wiringcomplete all as specified and directed. (NOTE : Two run of single core PVC cable with one run of earth conductor and conduit /batten shall be measured as one unit.)

Supply, fixing, connecting & testing sheet metal single pole and neutral enclosure with metal clad (two pin and earth) plug top and socket complete with and including one No MCB ( 'C' series), SP, 20 Amps, 240 Volts, having breaking capacity 10 KA complete all as specified and directed.

Supply & fix sheet metal enclosure MCB distribution board. Single pole & neutral 240 volts 12 way double door complete with appropriate size bus bar and neutral link incl taking down all as specified and directed.

Supply & fix sheet metal enclosure MCB distribution board. Single pole & neutral 240 volts 4 way with double door complete with appropriate size bus bar and neutral link incl taking down all as specified and directed.

Supply and fixing MCB SP 6 to 32 Amp ('C' curve) having short circuit rating 10KA, 240 volts complete with connection testing and commissioning. Complete all as specified and directed.

Supply and fixing MCB SPN 40 to 63 Amp ('C' curve) having short circuit rating 10KA, 240 volts complete with connection testing and commissioning. Complete all as specified and directed.

M&L for earthing complete with galvanized earth plate electrode 600 x 600 x6mm thick burried directly in ground vertically to a depth not less than 2.25 M below normal ground level ) with top edge of the plate not less than 1.50 M below normal ground level , connected to and including galvanized steel wire 4mm dia as earth lead soldered and riveted to earth plate by means of nuts, bolts, check nuts & washers, of galvanized iron or steel with connected to test point and testing on completion including 15mm GI light grade pipe for earth lead protection from earth point to earth plate, including provn adequate quantity of charcoal dust mixed with 35 % common salt to a packed thickness of not less than 15 cm in alternate layers of charcoal and salt on all sides of earth plate with 20mm bore medium grade GI Pipe for watering,GI check nut, funnel and wire mesh with and including all necessary excavation & earth work in soft/loose soil, returning filling in, removal of surplus soil to a distance 50 metre,,PCC 1:3:6 type C-1 as in earth pit, 40 mm thick RCC cover using cement concrete 1:2:4 type B-1 reinforced with & including 8 mm dia mild steel TMT bar @ 100 mm c/c Both way with suitable handle for lifting arrangement & including form work complete all as specified and shown in electrical plate No 3 of MES SSR Part I 2009 and as directed. NOTES:- (i) On testing, after completion of Job, if desired earth resistance is not obtained, the earthing shall be redone at without any extra cost by contractor.

Taking down of electric meters 10-60 amps complete as specified and direced.

S&F in repair 4 Pair Telephone Cable 0.4 sqmm copper of diameter and is insulated with a special grade polyethylene compound on the latest state-of-the-art extruders. The cores are twisted together with a uniform lay from meter to CIU units, complete all as specified and directed.

S & F Rigid non-metallic PVC conduit 20mm dia exclusive of boxes (junction/ terminal) but inclusive of all tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc complete all as specified and directed.

Supply, fixing and connecting for Electric circuits for size of 1.0 sqmm copper FRLS wire for inverter in existing conduit/casing caping complete all as specified & directed.

S&F Wall mounting fan, electric driven single phase 230 volts, oscillating type, 400 mm sweep, high quality ABS base with high speed motor and balanced blades with three leafed and 3 core copper cable of suitable size, complete all as per specified.

Supply, installation, testing and commissioning of indoor type wall mounting size min (680 X 1100 X 245mm), Polycarbonate CPRI approved OEM made Meter Panel suitable for 04 (four) Single phase meter. The panel shall be made of modular POLYCARBONATE THERMOPLASTIC ENCLOSURES which should be UV resistance in accordance with IEC 61439-1, clause 10.2.4: The panel type wall mounted on mounting structure RAL 7016. The meter panel should be anti-acid & anti corrosive & fully transparent Door for meter vision. Degree of protection against mechanical load should be IK08 (5 Joule) in accordance with IEC 62262. The manufacturer of panel shall submit a copy of CPRI test report in polycarbonate only degree of ingress protection IP65 in accordance with IEC 60529. The gasket should be internally embedded made of polyurethane and enclosure make. The manufacturer of board/panel shall submit a copy of type test report of a board made out of Polycarbonate thermoplastic panel in accordance with IEC 60439-1 complete all as specified and directed. Note : Re-fixed the energy meter in new meter cabinet including all necessary electrical connection. General Specification & Electrical Parameters: 4 Meter DB Ref No. 2236 / 2023(REV-1). Type of Panel: -Thermoplastic Polycarbonate. Panel Size: -680x 1100x 245mm Degree of Protection: -IP65(EN60 529) SystemVoltage:415V,50Hz,4wire+E Installation: -Indoor Floor mounting Cable Entry: -Incoming/outgoing from bottom. Finish Shade: -Enclosure & Accessories: RAL 7035 Mounting structure: RAL 7016 Incomer: 125 A, FP 35mA MCCB-01 Nos Outgoing: 40A DP 10kA MCB – 4 Nos (5-32)A, 1Phase PREPAID ENERGY METER-4 Nos (Provision Only) Terminals- 10SQMM TERMINAL BLOCK- 8 Nos 10SQMM TERMINAL BLOCK- 4 Nos

Supply, installation, testing and commissioning of commercial type wall mounted electric chimney made out of IS Certified Width : 60cm, Suction Power : 1400 m3/hr, Function Type : Heat auto clean, Filter type: Baffle filter (SS), Finish : Black Control: touch with Gesture, Led : 1.5W LED, Warranty: 5 Years on product, 12 Years on motor, Product Dimension (WxDxH) (In mm) 600x430x425mm, equipped with odor sensor which will sense odor and adjust speed of chimney automatically remote control, autoclean alarm softlight complete all as specified and directed.

M/S DEVENDRA KUMAR GUPTA (BID ID -3420235)

M/s Srijan Construction Company (BID ID -3420684)

CREATIVE CONSTRUCTION (BID ID -3419615)

m/s shanti consruction co (BID ID -3418404)

Asha Construction (BID ID -3419206)

M/s Laxmi Associate (BID ID -3419669)

m/s Agra Builder (BID ID -3418608)

M/S RADHEY GOVIND ENTERPRISES (BID ID -3419192)