SPECIAL REPAIR TO BLDG NO P-56(1-8) OR MD ACCN AT PR LINES IN MIRAN SAHIB UNDER GE JAMMU

Amount

B&R PORTION:- Demolition of brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed.

Brickwork with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius built in cement mortar 1:4 complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) n.exc 1.5 sqm each, complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) exc 1.5 sqm but n,exc 4 sqm each, complete all as specified and directed.

Taking down cement plaster on brick or stone walls, etc.including raking out joints,hacking for key, scrubbing down with water, etc complete all as specified and directed.

15mm thick rendering in CM 1:6 on other than fair faces of brick work or stone masonry surfaces finished even and smooth with out using extra cement, complete all as specified and directed.

5mm thick rendering in CM 1:3 on ceiling surfaces finished even and smooth with out using extra cement, complete all as specified and directed.

15mm thick rendering in CM 1:4 on fair faces of brick work or concrete surfaces finished even and smooth with out using extra cement complete all as specified and directed.

Rough cast plaster complete all as specified and directed by Engr-in-Charge.

10mm thick rendering in CM 1:4 with mixing of liquid water proofing compound Pedilite LW plus @ 200 ml per 50 Kg of cement on concrete surface such as soffits, RCC chajja, roof projection etc complete all as specified and directed by Engr-in-Charge. Note : WPC will measured and paid separately as supply only.

Preparation of newly plastered wall surfaces and applying two coat of oil bound distemper over & including a coat of wall putty of 2 mm thick, complete all as specified and directed.

Complete removal of existing treatment on old surface of wall and applying two coat of oil bound distemper over & including a coat of wall putty of 2 mm thick, complete all as specified and directed.

Preparation of newly plastered wall surfaces and applying two coat of exterior emulsion over & including a coat of chalk whiting on plastered surface (over Item No. 8) complete all as specified and directed.

Preparation of newly plastered wall surfaces and applying three coat of white wash on newly plaster surface of ceiling (over Item No. 7) complete all as specified and directed.

Preparation of old treated surface of wall and applying one coat of exterior emulsion complete all as specified and directed.

Preparation of old plaster or painted surfaces of ceiling and applying one coat of white wash complete all as specified and directed.

Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and directed.

Factory made solid panel PVC Moulded Door shutter with particle boardcore, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick moulded prelaminated PVC Sheet on the front face & 2mm thick plain colour PVC sheet on back face supplying & fixing in frame at site as per specification & drawing .

35mm thick factory made plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and all as specified.

35mm thick factory made PVC moulded panel door shutter with masonite facing on both side of (two,three or four panel design as approved) made of solid core using machine filled rigid expanded polyurethane foam . The door facing plate shall be 3.2mm thick complete all as specified and directed.

35mm thick 2nd class hard wood factory made glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.20 (a) complete all as specified and directed.

Box type steel windows (factory made) outer frame made out ERW tube 'P' section 65X45X25 mm and shutter of ERW tube 'P' section 50mmX35mmX20mm openable (double shutter) with glazed shutter on exterrnal side and gauzed shutter on internal side including steel pintel hinges steel handle 100 mm long mild steel tower bolt 02 nos on each shutter stopper of 'Z' section and its locking arrangement and mild steel hook and eyes complete all as specified and shown on drgs No CEPZTD-324/07 Sh 1/3 to 3/3. Note:- The quoted rate a shall also include:- (i). One shop coat of zinc chromate primer on all exposed surface and one coat of tar on the ends of steel surface in contact with bricks / concrte surface. (ii) 4 Nos MS steel lugs made of 20X5 mm Iron flat 200 mm long. (iii) PCC block for embedding lugs. (iv) Cooler windows where required.including 10 mm dia mild steel framed works such as grills, framed guard bars, etc and similar work conforming to Fe410-0 or Fe 310-0 complete all as specified and directed.

18/19mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing with white lamination, including teak wood liping 6mm thick on sides complete all as specified and directed.

6mm thick teak wood lipping over prelaminated particle board, fixed with nails complete all as specified and directed.

Pressed steel frames (Factory made) size of frame 105X60mm made out of 1.25mm thick black MS sheet for doors with two rebates for fixing one shutter including necessary fixing lugs, hinges, lock strike plate, etc., complete including bottom of each chowkat to be welded with 2 Nos.25X25X3mm thick flat iron projecting 10cm on either side complete all as specified and directed.

Description all as per Item No. 25 above but size of frame 125X60mm for fixing of two shutters complete all as specified and directed.

Description all as per Item No. 25 here in before but size of frame 60X40mm complete all as specified and directed.

Steel ventilators with centre hung shutter including two pairs of brass cup pivots, catch spring and pulley wheel, complete all as specified and directed.

PCC 1:2:4 type B-0 using 12.5mm graded crushed stone aggregate as in back filling, bed block for hold fast, coping, benching on corner of joints etc complete all as specified and directed.

100mm size butt hinges medium weight cold rolled stainless steel complete all as specified and directed.

75mm size butt hinges medium weight cold rolled stainless steel complete all as specified and directed.

Aluminium handles D type anodised 150mm long ISI marked complete all as specified and directed.

Aluminium handles D type anodised 125mm long ISI marked complete all as specified and directed.

150mm long aluminium anodised barrel tower bolt of extruded section ISI marked complete all as specified and directed.

125mm long aluminium anodised barrel tower bolt of extruded section ISI marked complete all as specified and directed.

250mm long 16mm dia aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections complete all as specified and directed.

100mm size hasp and staple, safety type aluminium anodised including bolt to hinge plate and fixed with screws complete all as specified and directed.

2nd class hard wood small fittings such as brackets of any type, shaped door and window stops and the like,artical not exc 200 cu. cm each and fixed complete all as specified and directed.

Mild steel 150mm long, ordinary rat tail rod pattern springs including roller & roller plate complete all as specified and directed.

Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.00mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and directed.

3mm thick sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane complete all as specified and directed.

Preparing surfaces of new wood and wood based material of any description and girth, not otherwise described, and treated with two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

Preparing surfaces of old treated wood and wood based material of any description and girth, not otherwise described, and treated with two coats of synthetic enamel paint complete all as specified and directed.

Preparing surfaces of new steel material of any description and girth, not otherwise described, and treated with two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Screed bed or bedding layer of mortar 15mm thick for laying floor finished in CM 1:4 complete all as specified and directed.

Non - skid Ceramic colour tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but n.exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match.complete all as specified and directed.

Non - skid ceramic colour tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but n.exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match.complete all as specified and directed.

10mm thick rendering in CM 1:3 other than fair faces brick work & finished the surface even and fair faces to receive tiles complete all as specified and directed.

Non - skid ceramic colour tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but n.exceeding 0.18 sqm, in skirting / dados etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match.complete all as specified and directed.

Glazed ceramic colour tiles in vertical surface 300x 200x 7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match complete all as specified and directed.

18 to 20mm granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite incl taking down old complete all as specified and directed.

Screed bed or bedding layer of mortar 20 mm thick for laying floor finished in CM 1:4 complete all as specified and directed.

Machine cut kota stone slab flooring 16-18 mm thick as in floor jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing, grinding and polishing to yield mirror finish with machine, complete all as specified.

Machine cut kota stone slab flooring 16-18 mm thick as in riser of steps, skirting, dado etc jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing, grinding and polishing to yield mirror finish with machine laid over & including including 10 mm thick plaster in CM 1:3 , complete all as specified.

Demolition of concrete (unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and directed.

50mm thick PCC 1:3:6 type C-1 using 20mm graded stone aggregate as in plinth protection etc finished even and fair, complete all as specified and directed.

Taking up or down 15mm bore steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and directed.

Taking up or down 20mm bore steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and directed.

15mm tubes medium grade' galvanised, with all fitting and fixed to walls and ceilings or laid in floors complete all as specified and directed.

20mm tubes medium grade' galvanised, with all fitting and fixed to walls and ceilings or laid in floors complete all as specified and directed.

Refixing old steel water tubing of 15mm bore and connections in new or old position fixed to walls, ceilings and floors etc. including fittings as requiered, complete all as specified.

Refixing old steel water tubing of 20mm bore and connections in new or old position fixed to walls, ceilings and floors etc. including fittings as requiered, complete all as specified.

Dismantling water tanks of capacity exceeding 500 ltr and not exceeding 1000 ltr and removing from site, complete all as specified.

1000 Litre rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) three layers hoisted and fixed in position complete all as specified and directed.

Vitreous chinaware wash hand basin white, flat back of size 450x300 mm including 15 mm CP pillar tap but including brackets fixing to wall and two Nos 10mm dia 100mm long nut and bolt over brackets and CP waste coupling complete and waste pipe fixed in repairs, complete all as specified.

Vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests and P or S trap connection to flushing pipe, antisyphonage pipe complete including provision of cement concrete bedding complete all specified in SSR Part-I fixed in repairs, complete all as specified and directed.

PVC valveless, syphonic action type, flushing cistern,10 ltrs capacity low level, white, with inlet, ball valve, float and handle including brackets fixed in repairs, complete all as specified and directed.

Low density PVC connections commercial quality 15mm bore with PTMT nuts of length 450mm complete all as specified and directed.

15mm bore bib taps long nose/long body, cast copper alloy CP fancy type with capstan handle screwed down , screwed for brass , weight not less than 450gms ferrule and fixed in repairs, complete all as specified and directed.

15mm bore angle valves, cast copper alloy CP fancy type, half turn, screwed down, high pressure , with crutch or butterfly handle, weight not less than 450 gms screwed both ends for iron pipe or for unions fixed in repairs, complete all as specified and directed.

15mm bore brass stop cock, cast copper alloy CP with long shank and cup (concealed type), high pressure, with capstan handle screwed down , screwed for brass, weight not less than 450gms screwed both ends for iron pipe or for unions fixed in repairs, complete all as specified and directed.

110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls,complete all as specified.

20mm dia gun metal, globe or gate valve with iron wheel head , screwed both ends for iron pipe fixed in repairs, complete all as specified and directed.

Shower rose brass chromium plated with swivel joint of size 125mm cast copper alloy type fixed in repairs, complete all as specified and directed.

Taking up or down CI/PVC pipes (including all fittings), with spigot and socket ends and lead joints including burning out joints and removing lead of 110/100/75mm dia pipe complete all as specified and directed.

Cast iron soil, waste and vent pipes (sand cast type) of bore 100mm dia in any length with or without ears, with cement joints fixed to wall complete all as specified and directed.

Cast iron soil, waste and vent pipes (sand cast type) of bore 75mm dia in any length with or without ears, with cement joints fixed to wall complete all as specified and directed.

Cast iron vent cowl 100mm core complete all as specified and directed.

Cast iron vent cowl 75mm bore complete all as specified and directed.

Stack clamps out of 50mmX5mm flat iron and 16mm dia round iron stays including bolts and nuts and securing ends of stay to walls or roof for 75mm bore pipe complete all as specified and directed.

Stack clamps out of 50mmX5mm flat iron and 16mm dia round iron stays including bolts and nuts and securing ends of stay to walls or roof for 100mm bore pipe complete all as specified and directed.

75/100mm cast iron floor trap with stainless steel grating including jointing to waste pipe fixed in cement concrete 1:2:4 type B1 complete all as specified and directed.

Stainless steel grating doom 125/100/75mm dia with hole ( minimum weight 25 gms) complete all as specified and directed.

20mm dia ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed in repirs (Minimum weight 210gms) complete all as specified and directed.

Brass CP towel rail 20mm dia 'D' type 60cm long between flanges complete all as specified and directed.

MS peg set of six powder coated as approved by GE complete all as specified and directed.

Drapery curtain rod of metalic 20mm dia covered with PVC coating including with MS bracket, end ball, rounded block (coated with brown/cherry/goldencolour ) of approved pattern and shade fixed in position by drilling holes in walls and fixed the brackets with raw plug and steel screw, complete all as specified and directed.

Glass shelf rectangular size 450mm X 15omm , 5mm thick glass with stainless steel bracket as per sample kept in AGE B/R office complete all as specified and directed.

Cabinet mirror of PVC moulded size 600mm X 450mm as per sample kept in AGE B/R office complete all as specified and directed.

Sinks with drainage board made of stainless steel 1 mm thick in kitchen with plugs, washer and waste pipe; including bedding in cement mortar on wall or including fixing cantilever brackets and connecting union to pipe, overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm, complete all as specified and directed.

Plate rack made of stainless steel 1 mm thick of size 600mm X 900mm fixed with washer and plugs fixed in repairs, complete all as specified and directed.

Providing precast cement concrete louvers and jallies made out of cement concrete type B-0 1:2:4 (using 12.5mm crushed stone aggregate) set in CM 1:6, 50mm thick (measured solid), including all mouldings and taking down old jallies complete all as specified and directed.

Demolition of cinder concrete of any description and in any position and removing the rubbish from work site complete all as specified and directed.

Preparing surface of sunken slab and applying 15mm thick cement plaster in CM 1:4 with mixing of liquid water proofing compound Pedilite LW plus @ 200 ml per kg of cement both on floor & wall finished surface even and smooth. The surface shall then be cured and filled with water for 48 hours and allowed to dry then apply APP based polymeric membrane minimum weighing 3 kg/sqm and minimum 3 mm thick reinforced with polyster non wove fabric (wt not less than 150gms/sqm) laid with 75mm side overlap and 100mm overlap on primed surface by forced application as per manufactures instructions over one coat of industrial bituminious 85/25 grade at the rate of 1.20Kg/Sqm over the plastered surfaces of sunken floor / wall and applying a course of a coat of binding material with blown type bitumen of grade 85/25 heating to working temperature of 180 digree celcias and applied @ 1.2 Kg/sqm over bitumen felt and sunken floor shall be filled with graded cinder concrete upto top level to receive to flooring complete all as specified and directed.

Demolition / removing of existing roof treatment of any description in any condtion including removing of top surface and removing all the debris to a distance n.exc 100m and roughening surfaces by sweeping clean ans washing down with water to remove dust etc and applying evenly cement slurry at the rate of 3kg/sqm over cleaned surfaces complete all as specified and directed.

20mm thick cement screed in CM 1:4 mixed with mixing of liquid water proofing compound Pedilite LW plus @ 200ml per 50 kg of cement finished surface even and smooth or laying of water proofing membrane complete all as specified and directed. (Note: WPC will measured and paid separately as supply only).

Cleaning the entire roof surface throughly to remove all loose particles dust/dirt particle and applying with one coat of industrial bituminious 85/25 grade at the rate of 1.20Kg/Sqm over the plastered surfaces of roof complete all as specified and directed.

APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) laid with 75mm side overlap and 100mm overlap on primed surfaces by forced application as per manufactures instructions complete all as specified and directed.

Applying a course of a coat of binding material with blown type bitumen of grade 85/25 heating to working temperature of 180 ° C and applied @ 1.2 kg/sqm over bitumen felt, complete all as specified and directed.

PCC 1:2:4 type B1 using 20mm graded crushed stone aggregate as in roof padding etc finished surface even and fair complete all as specified and directed.

PCC 1:2:4 type B-0 using 12.5mm graded crushed stone aggregate as in coping, in roof & base for water tank complete all as specified and directed.

Framed brackets of angles or tees with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angles, as necessary, as in cooler stands etc conforming to Fe.290.Gde-E-165, complete all as specified and directed.

Supply only liquid water proofing compound.

E&M PORTION:- Taking down carefully unsv aluminium / copper conductor point wiring (light, fan, light socket, power socket) complete fitting such as swithes, sockets, lamp holder, utility light fitting, fan regulator etc and removing materials from sites and making good distrubed surface of walls and roofs complete all as specified and as directed.

Taking down carefully unsv main switch / DBs alongwith MCBs / wooden board / connected fittings & fixtures any type and making good distrubed surface of walls and roofs to match the existing surface, complete all as specified and as directed. Note:-Old serviceable switches & MCB shall be taken on charge by the MES for reuse and unsv fittings shall be credited to the contractor.

Taking down carefully existing serviceable meter box along with Energy metre from building for reconditioning of meter box and setting aside the energy meter for refixing. Then applying syhnthetic enamal paint on meter box as directed by Engineer in charge at site and refixing the same after changing its hinges, screws, lock system etc including refixing of energy meter at the same meter box including making good distrubed surfaces to match with the existing finishes, complete all as specified and as directed. Note:-Energy meter will be handed over to MES store at the time of taking down and will collect from a store after copmpleting the wghole work at site for refixing.

Point wiring with 1.5 Sqmm single core multi stranded copper conductor FRLS PVC insulated and unsheathed heavy duty cable in colour code including contineous earth wire with cable of size 1.5 sqmm copper conductor flexible FRLS insulated drawn in and including concealed PVC rigid conduit / surface PVC casing caping medium grade ISI marked terminated into CI/pressed steel terminal boxes including 3.00mm thick hylam brand IS-2036 marked, laminated sheet cover for mounting switches, sockets, fan regulators etc complete all as specified and as directed for the following :-

One light/fan point controlled by one, one way switch 6 Amp complete all as specified.

One 3 pin socket outlet 6 amp on same board complete all as specified.

One 3 pin socket outlet 6 amp independent board, complete all as specified.

Description all as per srl item No 108 here in before but for one 3 pin socket outlet 16 Amp independent with cable of size 2.5 Sqmm for point wiring and 1.5 sqmm as in continuous earth wire.

Switch piano flush type 6 Amp single pole two way, (ISI marked), complete all as specified.

Switch socket multipurpose combination 2 in 1, 3 pin, 5 and 15 Amp flush type universal,complete all as specifed.

Fan regulator stepped type (electronic ) flush type for 1200/1400mm sweep AC ceiling fan, complete all as specified. .

Musical door bell, 230 volts AC supply all as specified and directed by Engineer-in-Charge.

Bell push piano flush type 6 Amp, (ISI marked), complete all as specified.

Ceiling rose (ISI Marked) 3 Phase PVC/poly carbonate, insulated body, compete all as specified.

Taking down carefully sub main wiring of any type and making good distrubed surface of walls and roofs to match the existing surface, complete all as specified and as directed.

Sub main wiring with single core cable 2x 2.5 sq mm FRLS insulated unsheathed stranded copper conductor cable 1100 Volts grade including 20mm rigid PVC conduit (Concealed) medium grade alongwith 1x 1.5 Sq mm FRLS insulated unsheathed copper conductor cable as earth wire connected with main earth dolly including chesing, cutting & making good to match with the existing surface, complete all as specified and directed. Note:-2 wire of 2.5sqmm, 1 wire of 1.5qmm and one run of pvc conduit shall be measured as one unit.

Taking down old serviceable light light fitting any capacity & setting aside for re-use, then refixing the same after necessory repair wor and making connection with three core copper flexible cable of suitable size to light fitting with ceiling rose, complete all as specified and directed.

Tube light fitting box type suitable for LED 18-20W tube Rod with end cap made out of CRCA sheet powder coated complete with hosing with all accessories pre wired and making connection with three core copper flexible cable of size 23/0.0076 from ceiling rose to PVC connection to light fitting including 18-20LED tube rod 4 feet long complete all as specified and directed. Make:-Crompton Cat Part No:-LTT8-20 for LED tube rod & DMLN1LT8-16 for fittings or Equivalent cat part of make as specified in Appx 'F' here in after. Note :- The LED batten and LED tube rod shall be of same make.

Lamp holder PVC/Polycarbonate type with back plate suitable for batten fittings, complete all as specified and directed.

LED lamp 5W, complete all as specified. Make:- Crompton Cat Part No LED 5W - B22 - CDL or Equivalent cat part of make as specified in Appx 'F' here in after.

Distribution board TPN 4 ways IP 43-'IK 09 with bus bars neutral links blanking plates double door suitable for FP MCB/Isolator/RCCB/RCBO as incommer and SP MCB's as outgoing complete all as specified Make:-Legrand Cat part No :-5076 80 or equivalent cat part of make as specified in Appx "F" here in after and comprising of following:-. a) MCB TPN 63 amps 415 volts 10 KA 'C' series for incoming-01 No. Make:-Legrand cat part No-4086 83 or Equivalent cat part of make as specified in Appx 'F' here in after. a) MCB SPN 32-40 amps 240 volts 10 KA 'C' series for outgoing-06 Nos. Make:-Legrand cat part No-4086 17-4086 18 or Equivalent cat part of make as specified in Appx 'F' here in after. Note:- MCCBs and MCBs shall be measured and paid separately

Sheet metal enclosure factory made (Double door) for DBs, single pole and neutral, 240 volts, 8 way IP 54 - IK 09 with 200Amps rated bus bar fixed on walls, including connecting both incoming and outgoing cable termination with proper taping, lagging testing and commissioning, complete all as specified. Make:- Legrand cat part No-5076 41 or Equivalent cat part of make as specified in Appx 'F' here in after. Note for item No-121-122:- The unit rates includes for cutting the brick walls to accomodate BDs to make flush to wall and making good the disturbed surfaces including finishes to match with the adjoining surface.

MCB single pole and neutral 32 amps 240 volts 10 KA 'C' series all as specified. Make:- Legrand cat part No-4086 17 or Equivalent cat part of make as specified in Appx 'F' here in after.

MCB single pole 6 to 32 amps 240 volts 10 KA 'C' series all as specified. Make:- Legrand cat part No-4085 87 to 4085 95 or Equivalent cat part of make as specified in Appx 'F' here in after.

MCB single pole and neutral 40 amps 240 volts 10 KA 'C' series all as specified. Make:- Legrand cat part No-4086 18 or Equivalent cat part of make as specified in Appx 'F' here in after.

Earthing complete with galvanised mild steel earth plate electrode of size 600x600x6mm thick burried directly in ground earth (in vertical) earth pit not less than 2.25 mtr deep below normal ground level with top edge of the earth plate not less than 1.5 mtr below ground level connected to galvanised iron or earth lead wire 4mm dia (8 SWG) by means of nut, bolt, check nuts and washer of galvanised ironincluding PCC pit in PCC 1:2:4 type B-1 pre-cast RCC cover slab using reinfocement with XPM weighing not less than 1.87 kg/Sqm with suitable handle made of 12mm round bar, including necessary excavation and earth work in any type of soil, 20mm dia medium grade galvanised steel tube for watering with one end fixed with cast iron funnel and wire mesh, 15mm dia bore light grade galvanised steel tubing upto 7.5 m length for drawing earth lead wire protection pipe, common salt, charcoal, etc complete all as shown in electrical plate No 3 of SSR Part-I and testing on completion. Note:- Rate for earth lead wire & protection pipe upto 7.5mtr length are inclussive in this item & no extra payment shall be admissible for the same.

Taking down of existing exhaust fan and re-fixing the same after necessory repair / rewinding, complete all as specified & directed.

Taking down of existing ceiling fan and re-fixing the same after necessory repair / rewinding with provn of MS hook of suitable size and length if required at site and making connection with 3 core copper cable of required size including painting whereas required, complete all as specified & directed.

Supply and laying or fixing or passing through pipe 1100 volts grade heavy duty electric cable with XLPE insulated screened PVC bedded aluminium stranded conductor served with inner sheathing of PVC tape armoured with galvanised steel wire or tape and over all PVC sheathed of size 16 Sqmm x 4 core, complete all as specified.

Excavation in trenches in any type of soil not exceeding 1.5m wide and n.exc 1.5 mtr in depth for laying of under ground electric cable and getting out complete all as specified.

Returning filling in, including spreading, leveling, watering and well ramming in layers not exceeding 25cm thick in any type of soil complete all as specified.

Removing excavated surplus materials to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point, complete all as specified.

Dry river sand cushioning to UG cable 8 cm thick before laying and 15cm thick after laying complete all as specified and directed. Note:- 1.Dry fine sand of best available quality shall be used. 2.Punned thickness shall be made and paid.

Supply and laying sub class `B` bricks laid dry flat transversely along the length of cable with width equal to the length of bricks over sand cushioning as protection cover of cable laid, complete all as specified and directed.

GI pipe light grade 40 mm bore for cable protection fixed on poles or laid in trenches, under floor, ducts, road crossing etc with fixing clamps, nuts bolts, washer of requrered size if required, complete all as specified.

BALVINDER SINGH AND SONS

M/s CHOUDHARY TRADERS

M/S A TO Z ENGINEERS