Supply Installation Testing Commissioning of 100 mm nominal diameter G.I. pipe to be fitted as rising main under implementation of National Mission on Saffron for Bore well no 87 Samboora

Amount

Earth work in bulk excavation by manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 m2 on plan) including disposal of excavated earth lead upto 50 meters and lift upto 1.5 m, as directed by Engineer-in-Charge. ( All kinds of soil)

Installation, testing & commissioning of 100 mm nominal diameter class - 'B' flanged G.I. pipe. The job includes providing & fitting of G.I. bends 100 mm nominal diameter 12 mm thick, fabrication of offsets out of G.I. pipe as per the site requirement. The M.S. flanges are to be fitted to the G.I. pipe through electric arc welding of adequate strength & consistency using "Ador Advani" welding electrodes. Providing and Fitting of R.I. cloth gaskets, nuts & bolts with plate washers to the flanged joints & cutting of pipes to lengths by gas cutting. refilling of trenches and compaction after laying of the rising main. The job is inclusive of the cost on account of tools and tackles, hire charges of machinery, carriage of pipes from Pulwama with head loads etc & testing on full load

Supply, Installation, Testing, Commissioning of 90o G.I. bend 100 mm nominal dia, 4.0 mm wall thickness, flanged on both sides

Providing and fitting of Non Return Valve (NRV) to the above rising main having following specification. The job includes providing and fitting of compatible flanges, nuts, bolts, gasket, etc. Technical Specification a) Type: Flanged swing check valve, single chamber type b) Nominal Diameter : 100 mm c) Nominal Pressure : PN 16 d) Material of Construction i) Body, Bonnet, Check valve Disk : Ductile Iron (GGG-40) ii) Hinge/Stop pin : Stainless steel iii) Plate seat : Stainless steal iv) Gasket & seal : EPDM rubber e) Corrosion Protection : Inside & outside epoxy coated Make: IVC/ VAG/ Talis

Providing and fitting of 50mm dia, flanged Air Release Valve (ARV) to the above rising main having following specification. The job includes providing and fitting of compatible flanges, nuts, bolts, gasket, etc. Technical Specification c) Nominal Pressure : PN 25 d) Material of Construction: Ductile Iron (GGG-40) ii) Hinge/Stop pin : Stainless steel iii) Plate seat : Stainless steal iv) Gasket & seal : EPDM rubber e) Corrosion Protection : Inside & outside epoxy coated. The Air Release Valve is to be provided with MS protection cage. Make: IVC/ VAG/ Talis

Earth work in bulk excavation by manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 m2 on plan) including disposal of excavated earth lead upto 50 meters and lift upto 1.5 m, as directed by Engineer-in-Charge. ( All kinds of soil) for Providing, installation, testing & commissioning below mentioned pipe.

Providing, installation, testing & commissioning of 100 mm nominal diameter class - 'B' flanged G.I. pipe. The job includes providing & fitting of G.I. bends 100 mm nominal diameter 12 mm thick, fabrication of offsets out of G.I. pipe as per the site requirement. The M.S. flanges are to be fitted to the G.I. pipe through electric arc welding of adequate strength & consistency using "Ador Advani" welding electrodes. Providing and Fitting of R.I. cloth gaskets, nuts & bolts with plate washers to the flanged joints & cutting of pipes to lengths by gas cutting. refilling of trenches and compaction after laying of the rising main. The job is inclusive of the cost on account of tools and tackles, hire charges of machinery, carriage, head loads etc & testing on full load

Providing & Laying of 03 no. cement concrete saddle blocks in M20 (1:cement, 2: course sand, 4: crushed stone aggregate) to be laid as per instructions of engineer-in-charge

Providing, Installation, Testing & Commissioning of 100 mm nominal diameter washout system which includes P/F of 100 mm nominal diameter equal TEE flanged on all sides with wall thickness 5 mm & 100 mm nominal diameter, with 4.5 mm wall thickness Kirloskar make sluice valve. The Sluice Valve of Cast Iron shall be double flanged, with non-rising spindle, conforming to IS 2906, PN - 10 Mpa rating, flanges faced and drilled as per IS 1538. The spindle is should be made of high tensile brass/bronze, and the spindle nuts and rings of leaded gun metal. The Valve must be complete with hand wheel. The Sluice Valve is to be fitted to the TEE on one side and delivery pipe on another side by a flanged joint. The flanges must be perfectly compatible to the inbuilt flanges of the sluice valve. The flanged joints are to be made leak proof by way of providing and fitting of reinforced gasket sheet, M.S fasteners (Nuts and Bolts), M.S Washers, etc.

Installation, Testing and Commissioning of horizontal pumping equipment coupled to 25 HP electric induction motor (already available withthe department) along with providing and fitting of 100 mm dia G.I. "B" Class suction / delivery pipes (Make: Prakash Surya/ Jindal/TATA) (05 mtrs each) and bends along with 25 mm sq, 3 core submersible cable (Make: Finolex/ Havells/ KEI) (100 mtr) in two limbs of to be laid from panel to motor

Providing and fitting of priming arrangement. The job includes providing of 100 litre PVC tank, 8 meter 15mm dia GI pipe along with sockets , bends, unions and 02 No. 15mm ball valves. The job also includes providing and fitting of angle iron stand. Make: Sintex/Vertex/ Star or equivalent

M/S SUPREME ENTERPRISES