REPAIR TO JOINERY CUPBOARD KITCHEN CABINET ETC AT MAP ACCN AND CLEANING OF SEWAGE LINE SEPTIC TANK SOAK WELL ETC IN ZONE F AREA OF AGE BR II UNDER GE WEST LUCKNOW

Amount

Demolition of brick work or stone/ boulder masonary, built in cement mortar or cement lime mortar including all quions, arches, pillars, etc. but excluding ashlar facings, dressed stone work and precast concrete articles etc. complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings not exc. 15 cm thickness (below or above ground level) complete all as specified and directed.

Demolition of cement concrete (reinforced) of any description and in any position not otherwise specifically provided for complete all as specified and directed. NOTE: Reinforcement shall be cut as required to facilitate demolition.

Excavating in trenches n.exc 1.5m wide and n.exc 1.5m in depth for foundation etc or for shafts, wells, cesspits, manholes, pier holes etc n.exc 10 sqm on plan and n.exc 1.5m in depth and getting out in soft/ loose soil complete all as specified and directed.

Returning, filling in, trenches including spreading, levelling, watering and well ramming in layers not exc. 25cm in soft/ loose soil complete all as specified and directed.

Removing surplus excavated material n.exc 50m and depositing where directed at a level n.exc 1.5m above the starting point complete all as specified and directed.

M&L cement concrete 1:4:8 type D-2 using 40mm graded stone aggregate as in foundations, filling and mass concrete complete all as specified and directed.

M&L for brick work with old size fly ash bricks of class designation 75, straight or curved on plan exceeding 6m mean radius built in cement mortar 1:4 complete all as specified and directed.

M&L Cement Concrete 1:2:4 type B-1 using 20mm graded stone aggregate as in lintels upto 1.5m clear span, cills, steps, seismic and other bands, plinth courses, string cources, lacing cources, parapets and railing upto 60cm in hight, copings, kneelers, apex stones, bed plates, water troughs, hold fasts and the like including weathering, slightly rounded or chamfered angles and throating including necessary formwork complete all as specified and directed.

M&L Mild Steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L Mild Steel TMT bars 6 to 8mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) area n. exc 1.50 Sqm each complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) area exc 1.50 Sqm but n. exc 4sqm each complete all as specified and directed.

Taking down shutters of any description, area n. exc 1.00sqm each complete all as specified and directed.

Taking down shutters of any description, area exc 1.00sqm but n. exc 2.00sqm each complete all as specified and directed.

Taking down shutters of any description, area n. exc 1.00sqm each and refixing in same opening complete all as specified and directed.

Taking down shutters of any description, area exc 1.00sqm but n. exc 2.00sqm each and refixing in same opening complete all as specified and directed.

Resecuring or easing & adjusting without taking down shutters of any description, area n. exc 1.00sqm each complete all as specified and directed.

Resecuring or easing & adjusting without taking down shutters of any description, area exc 1.00sqm but n. exc 2.00sqm each and refixing in same opening complete all as specified and directed.

S&F pressed steel door frame of size 125x60mm with one or more rebates, made out of 1.25mm thick MS sheets including necessary fixing lugs, hinges, lock strike plate, etc. complete as specified and fixed including one shop coat of primer complete all as specified and directed.

M&L for preparation of surfaces of wood or wood based materials, steel and iron work, new or old of any description and girth, not otherwise described and treated with tar or coal tar black paint complete all as specified and directed.

S&F 35mm thick factory made 2nd class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc, (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut or mitred beads for securing glass, gauge etc sizes of members of shutters as specified in SSR Part-I Section 8 clause 8.24(a) and fitted to chowkats complete all as specified and directed.

S&F flush shutters 30 mm thick, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

S&F 35mm thick factory made 2nd class hard wood rail and style type plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P commercial ply or 12 mm veneered particle board with commercial venneering on both faces, the size of rail and stile as per IS: 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed.

S&F factory made Solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet, reinforced with MS square tube, supplying and fixing in opening with fittings as per specification & drawing complete all as specified and directed.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for Top & bottom rails, MS frame shall be covered with heat molded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail, Panelling of plain colour PVC sheet to be fitted in the MS frame welded/ sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement and fixing in frame at site as per specification & drawing complete all as specified and directed.

Taking down side hung, aluminium door shutters of any description, area exc 1.50Sqm but n. exc 4.00sqm each and refixing in same opening including provn of easing, necessary repair like replacement of aluminium beading, aluminium hinges, jointing cleats, glazing clips, rubber packing, screws etc complete all as specified and directed.

S&F in repair anodized aluminium glazed window and ventilator shutters, side hung/ top hung type without sash bars, with aluminium sections weighing not less than 0.55kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as 01 no. 150mm long peg stays, 02 nos. 100mm long hinges type B-21, 01 no. 150mm long tower bolts and 01 no. 125mm long handles including glazed with 5mm thick tinted glass complete all as specified and directed.

S&F casement windows with net and grill single or multi shutter, made out of uPVC multi cavity frame section of size 60x60x2.5mm, suitably reinforced, and double multi shutters division are made by using sash mullions of uPVC section of size 50x64x2.5mm, shutters made out of uPVC section of size 50x85x2.5mm, reinforced and welded in corners with EPDM gasket for provn of glass and air tight, outer side of shutter glazed with 5mm thick sheet glass and mosquito shutter made out of uPVC extruded section of size 61x27x2mm with 1.2mm thick GI channel, welded in corners, fibre mosquito net fitted in shutter with required accessories, 12mm round grills are inserted in main frame and fixed as per manufacturer's instructions complete all as specified and directed.

S&F Solid PVC frame (single rebated) size 60mmx30mm made out of solid PVC foam with homogeneous fine cellular structure having smooth outer integral skin with suitable metal stiffner and fixed with 100x8 sheet metal CSK screws complete all as specified and as shown on drawing. NOTE: Door frame shall be water proof, termite proof, elegant and should have excellent screws holding strength to fix hinges and hold doors properly for a long life

S&F 28mm thick factory made solid PVC profiled panel door shutter with integral skin as frame & 3mm thick high pressure compact laminate on both sides of approved colour as infill, with ‘C’ type GI or 40x20x19mm of MS pipe as stiffner and fixed in frame at site as per specifications and drawing complete all as specified and directed.

S&F 100mm size butt hinges, medium weight, cold rolled, mild steel and fixed with screws complete all as specified and directed.

S&F 150mm size extruded aluminum alloy handles, fabricated type, anodised complete all as specified and directed.

S&F in repair 150mm size extruded aluminum alloy handles, fabricated type, anodised complete all as specified and directed.

S&F 100mm size extruded aluminum alloy handles, fabricated type, anodised complete all as specified and directed.

S&F 150mm long Aluminium, anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed.

S&F in repair 150mm long Aluminium, anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed.

S&F 300mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and directed.

S&F in repair 300mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and directed.

S&F in repair door closer, aluminium (die cast) body, hydraulically regulated, designation No 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified and directed.

M&L in repair 18/19mm thick 1st quality plywood, grade BWR, type BB fixed with screw/ nails to timber frame work as in pelmet boxes/ cup boards and cabinets etc including 6mm thick teak wood lipping alround complete all as specified and directed.

M&L 0.90mm thick decorative laminates type 1 of surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturer's instructions complete all as specified and directed.

S&F Continuous (piano) hinges, mild steel, bright finished or electro galvanised, with width of flap 30mm when open, and fixed with screws complete all as specified and directed.

S&F 100mm long aluminum anodised, hasp and staple, safety type, with mild steel hinge pin including bolts to hinge plate and fixed with screws complete all as specified and directed.

S&F in repair 300mm long, mild steel, ordinary rat tail rod pattern springs including including roller and roller plate complete all as specified and directed.

S&F in repair 50mm dia, polished, hard wood knobs for cupboards, decorative, fixed with nut, screws and washer, bright finished complete all as specified and directed.

S&F in repair floor door stopper of aluminium alloy body and tongue, anodized, with hard drawn steel spring, fixed in floor, overall length of cover plate 150mm complete all as specified and directed.

M&L for in repair 3mm thick sheet glass, ordinary quality and glazing with oil putty or wooden beads in square, area n.exc 0.5 Sqm in each pane complete all as specified and directed.

S&F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F in repair stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F in repair anodised aluminium expanded type wire cloth, 1mm nominal dia of wire and average width of aperture 5mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F in repair sliding chanel of drawer, 450 to 600mm long, mild steel, chromium plated, heavy duty, superior quality and fixed complete all as specified and directed.

M&L 2nd class hard wood, plain fillets, sectional area exc 13sqcm but not exc 25sqcm, square, rectangular or triangular in secction, wrought finished, secured with nails or brads complete all as specified and directed.

S&F in repair 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing complete all as specified and directed.

S&F in repair 5mm thick Solid PVC Wall Lining consisting of 5mm thick Plain colour PVC sheet incluseive of solvent cement and fixing at site on PVC frame as per specifications and drawing complete all as specified and directed.

Dismantling plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and directed.

S&F fibre glass reinforced translucent corrugated sheeting with two corrugations side lap fixed with coach screw and washer with EDPM seal in roof, wall etc complete all as specified and directed.

S&F multi-rib TM profile, tensile strength 550 Mpa, colour coated 0.50mm thick pre-painted galvalume aluminium zinc coated GI based corrugated steel sheet, having maximum pitch of 250mm c/c and minimum 30mm crest depth in length as per site requirement, the feed material manufactured out of 0.50mm (TCT) with coating of 18-20 microns top coat over 5 microns primer and 8-10mm alkaline back of zinc aluminium alloy of AZ-150, including the sheet shall have a hot dip metallic zinc aluminium alloy coating of zinc 43.5%, aluminium 55% and silicon 1.5% with total mass coating of 150 gms/sqm on both sides having covered width 1020mm and return leg for proper side lap as in roof covering/ cladding and fixed with self tapping screws with EDPM seal complete all as specified and directed.

M&L mild steel framed work such as grills, gratings etc. with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed.

M&L in repair structural steel work with rolled mild steel sections as in main and cross beams, hip and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors, fixed with angle cleats or other connecting plates etc and similar articles conforming to Fe-410W (Gde E-250) quality-A complete all as specified and directed.

Taking down cement or cement lime plaster any description from walls/ceiling etc including racking out joints, hacking for key & scrubbing down with water all as specified and directed.

M&L for rendering 15mm thick in CM 1:4 on fair faces of brick work or concrete surface of wall and finished surface even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15mm thick in CM 1:4 with integral water proofing compound @ 3% by weight of cement on fair faces of brick work or concrete surface of wall and finished surface even and smooth without using extra cement complete all as specified and directed. NOTE: WPC shall be measured and paid seperately under respective item.

Supply only integral waterproofing compound complete all as specified and directed.

M&L for preparation of new or previously untreated surfaces of wood or wood based materials of any description over 10cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L for preparation of new or previously untreated surfaces of steel or iron of any description over 10cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L for preparation of old or previously treated surfaces of wood or wood based materials of any description over 10cm in width or girth, not otherwise described and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for preparation of old or previously treated surfaces of steel or iron of any description over 10cm width or girth, not otherwise described and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for 75mm thick cement concrete 1:3:6 type C-2 using 40mm graded stone aggregate as in plinth protection, laid in panels, finished surface even and smooth without using extra cement and forming 12mm wide expansion joints to the full depth, and filled with pre-formed bituminous filler and top 30mm primed and sealed with sealing compound, Grade 'A' complete all as specified and directed.

M&L for precast cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate as in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves etc and similar works set in cement mortar 1:4 complete all as specified and directed.

S&F in repair Vitreous China wash down water closet pan, pedestal pattern, white, with 'P' or 'S' trap, excluding flushing cistern and flush pipe, including connection to drain pipe (or outgoing pipe) and to flushing pipe etc. and making good to floor complete all as specified and directed.

S&F in repair plastic water closet seat cover, white, closed pattern with flat bottom and cover, fixed with MS chromium plated or aluminium hinging device ISI marked as approved complete all as specified and directed.

S&F in repair Vitreous China squatting pan, 'Orissa pattern', size 580x440mm, white, with integral foot rests including PVC 'P' or 'S' trap, excluding flushing cistern and flush pipe, including connection to trap and flushing pipe etc. and making good to floor complete all as specified and directed.

S&F in repair PVC valveless, syphonic action type, low level, flushing cistern of 10 lit capacity, white, with inlet, ball valve, float valve and handle including bracket, rubber cone and flush pipe etc. and connection to pipes complete all as specified and directed.

S&F in repair 25mm dia mild steel PVC coated curtain rod, superior quality, any colour, with end brackets and end knobs and fixed to wall with wooden plug/ PVC gully with CP screws and cup washers complete all as specified and directed.

S&F in repair 100mm bore cast iron (sand cast) soil, waste and vent pipes in any length with or without ears, jointed with cement laid in trenches or in floors complete all as specified and directed. NOTE: Excavation and earth work shall be measured and paid separately under respective item.

S&F in repair 75mm bore cast iron (sand cast) soil, waste and vent pipes in any length with or without ears, jointed with cement laid in trenches or in floors complete all as specified and directed. NOTE: Excavation and earth work shall be measured and paid separately under respective item.

S&F 100mm bore cast iron bends (any radius), diminishing pieces or tapers (larger bore measured) complete all as specified and directed.

S&F 75mm bore cast iron bends (any radius), diminishing pieces or tapers (larger bore measured) complete all as specified and directed.

S&F 100mm bore cast iron branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches complete all as specified and directed.

S&F 75mm bore cast iron branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches complete all as specified and directed.

S&F in repair 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

S&F in repair 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

S&F PVC (SWR) bends of any radius, suitable for 110mm bore PVC pipes, fixed and jointed with solvent complete all as specified and directed.

S&F PVC (SWR) bends of any radius, suitable for 75mm bore PVC pipes, fixed and jointed with solvent complete all as specified and directed.

M&L cutting into existing manholes for connecting new drains, making good to 150mm bore pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished, and reforming benching as required complete all as specified and directed.

M&L cutting into existing manholes for connecting new drains, making good to 100mm bore pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished, and reforming benching as required complete all as specified and directed.

M&L for cleaning/desludging of existing soakage well of any capacity and depth with inlet/outlet chambers including taking out sludge (both organic and inorganic matter) in any form and other foreign matter etc viz sediment, sand, ash, grease, fibre, silt, roots or vegetation etc by means of sewage sucking machine and after plugging the incoming sewer line through combined high pressure water jetting/ suction (Vacuum) type machine mounted on LCV/HCV facility of high pressure vacuum and removing the sludge outside MOD land by any means at a place meant for the purpose by local munucipality complete all as specified and directed.

M&L for cleaning/desludging of existing septic tank of any capacity and depth with inlet/outlet chambers including taking out sludge (both organic and inorganic matter) in any form and other foreign matter etc viz sediment, sand, ash, grease, fibre, silt, roots or vegetation etc by means of sewage sucking machine and after plugging the incoming sewer line through combined high pressure water jetting/ suction (Vacuum) type machine mounted on LCV/HCV facility of high pressure vacuum and removing the sludge outside MOD land by any means and at a place meant for the purpose by local munucipality complete all as specified and directed. Note:- For measurement purpose, Liquid depth of septic tank shall be measured before removal of sludge.

M&L for cleaning/clearing of blocked/ chocked/ non functional sewage line up to 200mm bore of any type and location in between manholes, including manholes n.exc. 3.00m depth and sewage lines between manholes to septic tank/ soak well/ sump well and cleaning the same including desilting/ descaling of drain and manhole by manually or mechanically to make the line functional including taking out sludge and removing the sludge outside MOD land at a place meant for the purpose by local munucipality complete all as specified and directed.

M&L for cleaning/desludging of existing sewage line from nahani trap to 1st manhole by manually or mechanically of any capacity and depth including taking out sludge in any form and other foreign matter etc viz. sediment, sand, ash, grease, night soil, fibre, silt, roots or vegetation etc to make the line functional duly removing the sludge outside MOD land by any means at a place meant for the purpose by local munucipality complete all as specified and directed.

Taking out broken sewage line at a depth n.exc 1.5m and replacing with new sewage pipe line with 150mm bore SGSW pipe including jointing of pipe in CM 1:1 and haunching against the sides of pipe in PCC 1:4:8 type D-2 using 40mm graded stone aggregate including necessary excavation, earth work and disposal of material up to a distance not exc 50m and making necessary connection after cutting into existing sewage line/ manhole to make it functional complete all as specified and directed. NOTE: Cutting existing manhole and making good shall be measured and paid seperately under respective item.

Taking out broken sewage line at a depth n.exc 1.5m and replacing with new sewage pipe line with 200mm bore SGSW pipe including jointing of pipe in CM 1:1 and haunching against the sides of pipe in PCC 1:4:8 type D-2 using 40mm graded stone aggregate including necessary excavation, earth work and disposal of material up to a distance not exc 50m and making necessary connection after cutting into existing sewage line/ manhole to make it functional complete all as specified and directed. NOTE: Cutting existing manhole and making good shall be measured and paid seperately under respective item.

Cleaning of drain of size 30 to 60 cm wide including removal of mud or foul in position (to be dumped in pit made by excavation in soft soil and filled with earth) complete all as specified and directed.

M/S ANIL KUMAR

M/S SIDHARTH TRADING CO.

R K CONTRACTOR AND SUPPLIERS

M/s Sachkhand Traders

M R CONSTRUCTION

chandra kaushal supplier

Matrubhoomi Construction