8758/E8 SPECIAL REPAIR TO SECURITY FENCING IN COMMUNITY HALL (P-49) AT NAD SUNABEDA

Amount

Dismantling of RCC posts and struts of any section including taking out embedded portion and making good disturbed ground and removal all debries and complete all as directed by Engr-in-Charge.

Dismantling fencing wire, any type complete all as specified and directed.

Excavation in post hole each n exc 0.5cum getting out in hard/dense soil, returning, filling in and ramming earth or broken rubble mixed with earth around in layers not exc 25 cm, watering and removing surplus soil to a distance n exc 50m and making good surface complete all as specified and directed

Excavation in trenches, n exc 1.5 m wide and n exc 1.5m in depth for foundation, etc and getting out in hard / dense soil all as specified and directed.

Returning, filling in, includingn spreading, levelling, watering and well ramming in layers n.exc 25cm thick in soils all as specified.

Removal of excavated material n exc 50m and depositing where directed at a level n exc 1.50m above the starting point all as specified.

M & L PCC (1:4:8) type D2 (Using 40mm graded stone aggregate) as in foundation filling in mass concrete complete all as specified and directed.

M & L for Plain Cement concrete Type B1 (1:2:4) using 20mm graded crushed stone agg as in foundations, filling and mass concrete complete all as specified and directed.

M&L Pre cast RCC (1:2:4) type B1 (using 20mm graded stone aggregate) as in fencing posts, straining or terminal posts, struts etc. for fencing average cross sectional area exceeding 100 square cm and not exceeding 250 sq cm with or without chamfered angles and flat, splayed rounded or mitred tops all as specified.

Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed by Engineer-In-Charge.

All as per srl item No.10.00 here-in above but 6mm to 8mm dia

S & F for rolled flats for securing mesh as fencing post strut bend to shape holes drilled notches cut to receive MS bolts and barbed wire, embedded to concrete including tarring to steel work embedded to concrete necessary welding etc. conforming to Gde E-250 (Fe 410-W) quality `A’ ISI marked (IS-2062) complete all as specified.

S & F for 10mm dia mild steel round bars as in tie bars fixed to fencing posts including cut to length, bent to shape, welding of bar at spots as directed and other similar works, conforming to Grade Fe 410W (Gde-E250), complete, all as specified & directed.

S & F for Mild steel bolts, nut, washer (Machine made) with hexagonal head one end and screwed the other, or screwed both ends; each screwed end to be fitted with two washers and one nut hexagonal dia of shank n.exc 12mm and length of bolt exc 50mm but n.exc 100mm complete all as directed.

Supply only Chain link MS galvanisd fencing, using hot dip GI wire of size 3mm dia and size of mesh 100mmx100mm complete all as specified. Note:- Flat iron, round bars, nut bolts and washer shall be measured and paid for separately.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provission of binding wire complete all as specified. Note :- Supply only chain link fencing shall be measured and paid for separately.

M&L for preparation of new or previously untreated steel and iron surfaces of any description not exceeding 10 cm in width or girth and applying two coat of synthetic enamel paint (Ist quality) over a coat of red oxide primer complete all as specified and directed.

Material and labour for preparation of new plastered surfaces of walls and applying two coats of cement base paint over a coat of primer complete all as specified and as directed.

Material and labour for brick work with Fly ash brick, straight or curved on plan exceeding 6m mean radius built in cement Mortar 1:6 complete all as specified and as directed.

M&L rendering 15mm thick in cement mortar 1:4 on fair faces of brick masonry or concrete surfaces of walls finished even & smooth without using extra cement complete all as specified.

M&L for Plain cement concrete type C-1 (1:3:6), using 20 mm graded granite stone aggregate as in coping, surface channel, bed plates, anchorage blocks and the like, including necessary formwork, complete all as specified.

M/S SANTOSH SATAPATHY

M/s Jai Sree Hari